PROVN OF COVERED PARKING SHED, TOILET BLOCK, GARBAGE RECEPTORS, DRAIN COVER AND SECURITY LIGHT AT VARIOUS LOCATION IN RMS

Amount

Excavation in post holes (or similar holes) each n. exc 0.50 m and getting out ,in Soft/loose Soil.

Excavation in trenches n exc 1.5m in deepth and 1.5m in width and getting out soft/loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm.

Removing excavated soil to a dist n.exc. 50m and depositing where directed at a level n.exc.1.5m above the starting point

Hard core of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to true surface.

M & L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete .

M&L 75 mm thick PCC 1:4:8 type D2 (40mm graded aggregate) for floor sub base.

M&L 25mm thick PCC 1:2:4 type B1 (20mm graded aggregate) for floor .

M&L 40mm thick DPC 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork.

M&L providing cement concrete 1:2:4 type B1 (Using 20mm graded stone agg) , 40mm thick as in floor/paving etc.

M&L 75mm thick cement concrete type C-2, 1:3:6 (40mm graded stone agg )as in plinth protection finishing the cement concrete surface even and smooth without using extra cement.

M&L cement concrete 1:2:4 Type - B1 ( using 20mm graded stone aggragate) as in coping

M&L RCC 1:2:4 type B1 ( 20mm graded stone aggragate) for lintel beam, cantilevers, bressummers, manhole/ soak well/ septic tank slabs/ covers etc.

M&L PCC 1:3:6 type C-2 (using 40mm stone aggregate) as in channel/drain complete all as specified and directed.

Extra for forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms,mitred stopped ends etc

S&F milt steel TMT bars 10mm, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

All as per item no 16 but, 6mm to 8mm dia.

S&F steel work in tubular trusses including (purlins and rafters) special shaped washers etc complete using ERW or induction butt welded tubes .

S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0.

S&F Framed work as in doors or gates of angles or other section with gusset plates, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides 0 and hanging; also fastening and fixing complete.

M&L for steel ventilator with top hung shutter including hinge, steel peg stay complete.

S&F pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified .

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L rendering 15mm thick on other than fair faces of brick work or concrete surfaces with CM (1:4)finished even and smooth without using extra cement.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cement.

Non skid ceramic colour tiles (300 x 300 mm) x 7 mm thick in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed or bedding of cm 1:4 layer in floor finishes complete all as spd

M&L coloured glazed tiles 300x200x6mm thick on vertical surfaces such as skirting, dados and rises to steps etc set in jointed in neat cement slurry and pointed to match

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling and fixing in opening as per specification and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rail M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck in side with solvent cement of styles and plain colour of PVC sheet for top rail lock rail and bottom rail, on either side & gap insert for top rail bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed tohether with solvent cement, at site as per specification & drawing.

Supply and fixing 100mm size stainless steel butt hinges,medium weight, cold rolled complete all as specified and as directed.

Supply and fixing 125 mm size mild steel butt hinges, heavy weight, cold rolled complete all as specified and as directed.

S&F Extruded Aluminium alloy handles 125mm long, fabricated type anodised complete all as specified.

S&F Aluminium anodised barrel tower bolts 100mm long of extruded section complete all as specified.

S&F mild steel sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with end incl min 6 bolt, 4 nuts or bolt plate and two on staple plate 300mm long complete all as specifed and directed.

Supply and fixing 3 mm thick frosted glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane complete all as specified and as directed by the Engr-in-Charge. Make : Modifloat/Ashai/Saint Gobain.

S&F for soap dish Size 160x160x90mm fixed with chromium plated brass screws.

S&F for Tubular towel rail brass chromium plated 20mm dia D type 60cm long between flanges.

S&F 15mm GI tubing 'Medium grade' with all fiting and fixed complete tom wall and celing or laid in floor of fllowing sizes complete all as specified.

-ditto- as per item No 38 above but 20mm bore.

S&F bib taps, cast copper alloy with crunch or butterfly handle screwed down, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed of 15mm bore size complete all as specified..

S&F in for 15mm dia of pipe Angle valves fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .

Supply and fixing for 100mm dia grating doom with waste hole of PTMT (minimum weight 25gms) complete all as specified and as directed by the Engr-in-Charge. Make: Prayag / Polytuf

S&F PVC (SWR) floor trap 75mm size, plain with grating including jointing with solvent cement of 75mm dia complete all as specified.

S&F 75 mm bore PVC (SWR) branch piece single (SingleY) equal or unequal complete all as specified.

S&F PVC (SWR) pipes of 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

M & L for 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F 110mm bore PVC (SWR) branch piece single (Single Y equal or unequal) complete all as specified and directed.

S & F for 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap.

Supply and fixing 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed.

M&L for painting to cement plaster surfaces with two coats of cement base paint after preparation of surface.

M & L Preparing new plaster surface apply two coat of cement base paint over a coat of primer on external walls complete all as specified.

M&L preparation of new surface and apply three coat of white wash on the walls.

M&L for preparation of new steel surfaces of any description, over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer.

M&L for preparation of new steel surfaces of any description, n exc 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer.

S&F MS plate (plain or chequred) channel, square cut or notched complete all as specified.

S&F for 125mm dia brass CP shower rose with revolving joints fixed to 15mm bore GI pipe complete all as specified.

M&L for cast iron wk grade FG 150, unmachiuned, (gully traps, gratings, railing, frames, manhole covers and similar articles exc 5 Kg each.

Supply and erect Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (8.5 metres long), as per IS-2713 including painting with one coat of black bituminous paint through out internally and externally up to ground level and remaining external surfaces of poles shall be painted with two coats of aluminium paint over a coat of red oxide, zinc chrome primer including dismantling the old steel tubular pole, complete all as specified and as directed. (Note: Excavation & earthwork , PCC foundation & coping shall be measured & paid separately) Make: BANSAL POLES / CALCUTTA POLES / JINDAL POLES / KWALITY STEEL-KOLKATA /NATIONAL TUBING COMPANY/ NEOZNE

M&L for white 48 Watt LED street light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and directedd. Make: Havells/Crompton/Surya Roshni Ltd.

M&L for PVC pole junction boxes with inbuilt aluminuim bus bar (02 Nos) of suitable size fitted over bus bar insulator and fixing to pole complete. Make :Sintex/Hensel/C&S.

M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 10 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. Make: Richa/Polycab/Havells/RR Kabel

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, one twin core cable flat or circular complete all as specified and as directed. Make: RR Kabel/Polycab/Havells

M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

M&L for replacement of HDPE pipes fixed to wall ceiling or floor of 25 mm bore.

Kalim sons

VIHUTO YEPTHO

Shri B K Ukil