REPAIRS TO DILAPIDATED ROOF SHEETS, FALSE CEILING,

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified

Material, labour and fixed of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material, labour and fixed of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) orinsulation boards/slabs/ blankets, any thickness, including cover fillets complete & removal all as specified

Material, labour and fixed of power coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X25mm X1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 6 mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer including taking dwon existing false ceiling system complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed.

Material, labour and fixed of rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde-E- 250) quality-A etc complete all as specified and as directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Dismantling timber scantling 40 Sqcm and over in section, in any position (Unframed work) complete all as specified and as directed.

Material, labour and fixed of 2nd class hardwood in scantling , clean sawn and fixed etc complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.

M&L for Rendering 15 mm in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Supply only integral water proofing compound complete all as specified and directed.

Material and labour for Preparation of new plastered surface and applying two coats of oil bound distemper over and including a coat of alkali resistant primer etc complete all as specified and directed.

Material and labour for Preparation of new surface and applying two coats of cement base paint over and including a coat of white cement base primer etc complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nailscomplete & removal all as specified

S&F 25mm thick Iind class hardwood boarding, any description, fixed in any position with nails complete & removal all as specified

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down shutters of any description n exc 1 sq. m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed.

Supply and fixing of 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Supply and fixing of 30 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for 35 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Material and labour for 30 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats complete all as specified and as directed.

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Material and labour for 25 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 75 mm size L type complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised handle cast type 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised handle cast type 125 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing in repair of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing of 300mm ordinary rat tail rod pattern springs including roller and roller plate complete made out of brass complete all as specified and as directed

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

Mild steel work as in bands, straps, supports or stays for RWP, ventilating pipes, clamps, hold fasts, wall ties conforming to Fe-290 Gde E-165

M&L for M-10 ( nominal mix ) using 20 mm graded stone aggregate as in hold fast blockage and similar work including formwork etc complete all ss specified and as directed.

Supply and fixing of Stainless steel wire cloth, 0.36 mm nominal dia of wire and avergae width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in repair of Stainless steel wire cloth, 0.36 mm nominal dia of wire and avergae width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads etc complete all as specified and as directed.

Supply and fixing of sheet glass 3 mm thick ordinary quality glazing with oil putty in squares in each pane n.exc 0.50Sqm. complete all as specified and as directed.

Supply and fixing of figured glass 4 mm thick oin headed type glazing with oil putty in squares in each pane n.exc 0.50Sqm. complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for old Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for Brick work with half bricks class designation 75, old size, straight or curved on plan to any radius built in Cement Mortar 1:4 complete all as specified and as directed.

Removal of existing detoriated tarfelt or any other treatment including PCC padding, loose surface and removing the debris to a distance n.exc. 50m and depositing where directed etc complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. etc complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface and finished even and fair without using extra cement, mixed with water proofing compound etc complete all as specifed and as directed. Note:- Water proofing compound shall be measure and paid separately

Material and labour for applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces etc complete all as specifed and as directed

Supplying and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance n.exc 100m at low lying area complete all as specified and directed

Demolition of cement concrete (reinforced) in any position ( (reinforcement cut as required to facilitate demolition) and removing rubbish to a distance 100m at low lying area etc complete all as specified and as directed.

M&L for cement concrete M-5 (nominal mix) using 40 ,mm graded stone aggregate as in filling under sunken floors etc complete all as specified and as directed.

M&L for 25 mm cement concrete M-15 ( nominal mix ) using 12.50 ,mm graded stone aggregate as in filling under sunken floors etc complete all as specified and as directed.

Materials and labour for sunken floor water proofing treatment of various layers from bottom to top on all surfaces of slab in following sequence and including demolition and removal of existing surfaces complete all as specified and as directed. (i) Slope correction by using M-20 (Nominal mix) concrete by using 12.5mm graded stone aggregate with integral water proofing compound ( minimum 2%), finished even and smooth using extra cement all as specified and as directed. (ii) Application two coats of elastomeric cementitious water proofing on sunken wall & floor surface as per the manufacturers instruction (iii) Concrete for sunken slabs shall be mixed with WP compound as per manufacturers Instructions.(To be measured separately) (iv) Joint of Trap/WC/Soil pipes shall be properly sealed with sealing compound( if required) (v) Testing of all traps & joints and sunken slab shall be as per IS-1742 before filling of sunken slabs, including smoke tests. (vi) 25 mm outer dia of CPVC pipe spout pipe of 600 mm length Note:- This item shall be measure in length & breadth of floor area and paid accordingly.

M&L for RCC M-15 ( nominal mix ) using 20 mm graded stone aggregate as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and as directed.

Material and labour for TMT Bars Fe 500D over and icluding 10mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc complete all as specified and as directed.

Material & Labour of 20mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) including taking down existing one complete all as specified and as directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removal of debris to a distance not exceeding 50m etc complete all as specified and as directed.

Material & Labour for 75 mm thick cement concrete M-10 ( nominal mix ) using 40 mm graded stone aggregete as in plinth protection ,finished fair and even without using extra cement etc complete all as specified and as directed.

Material & Labour cement concrete M-15 ( nominal mix ) using 12.5 mm graded stone aggregate as in coping / drain haunching etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.06 Sqm and not exceeding 0.11Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material and labour for Vitrified ceramic tiles light shade 10 mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement sand mortar etc complete all as specified and as directed.

Material and labour for Vitrified ceramic tiles light shade 10 mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm , in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed in cement sand mortar etc complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store.etc complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed. Note for item no 76 & 77:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requirements as directed by Engg-In -Charge and same shall deem to be included in quoted rate.

Cutting Chases for concealed water tubing etc in brick/concrete walls and making good to facing where required and pointing in CM 1:3 cutting not exceeding 10 cm girth complete all as specified & directed.

Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink with drain board of overall size 950mmx510mm and bowl size 410mm x410mmx230mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets etc complete all as specified and as directed.

Supply and fixing of in repair uPVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supply and fixing of vitreous china wash basin white flat back, size 580 x 450 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed.

Supply and fixing of Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white with including CI ‘P’ or ‘S’ trap & integral foot rests fixed in cement concrete and including taking down existing one complete all as specified and as directed

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover white including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc and including taking down existing one complete all as specified and as directed

Supply and fixing in repairs Vitreous China half stall urinals, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, magnum urinal spreader, pointing around urinal back in cement; flush pipe, grating and Union for discharge pipe and including taking down existing one complete all as specified and as directed

Supply and fixing of 50 mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceiling or in floors etc including cutting, chasing, pinning and making floor good with existing one all as directed

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed.

S&F Soap dish MS chrome plated fixed to wall with CP screws etc complete all as specified and as directed

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed to wall with CP screws etc complete all as specified and as directed

Supply and fixing in repair bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed

Supply and fixing in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed

Supply and fixing in repairs 15 mm dia brass CP fancy wall mixer 2-in-1 system with L Bend including hand shower with fiexble shower tube1.5m long for mixing hot & cold water screwed down for iron pipe and fixed as in repairs complete with hand shower rose and tube. Make :- Cat no For wall mixter Cat No.F280016 & for Hand shower F-160046 of Hindware or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repairs 15 mm dia brass CP centre hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed as in repairs. Make Cat No Cat No. 7650 of Paryag or equivalent model of make list as given in PS

Supply and fixing in repairs 15 mm dia fancy type Stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed.

Supply and fixing in repairs 15 mm dia fancy type Stop valves,concealed type, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed.

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Supply and fixing 32 mm bore 6 kg/sqcm for outlet pipe of WHB etc complete all as specified and as directed.

Supply and fixing 40 mm bore 6 kg/sqcm for outlet pipe of WHB etc complete all as specified and as directed.

Supply and fixing Stainless steel of 304 grade of kitchen plate rack of 1mm thick sheet size 24''x24''x10'' complete all as specified and as directed.

Dismantling HDPE water storage tank of capacity n.exc.500 litre and removing from site complete all as specified and as directed.

Dismantling HDPE water storage tank of capacity exc.500 litre but n,exc 1000 litre and removing from site complete all as specified and as directed.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 1000 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supply and fixing in repair of 20 mm Ball valves ( min wt 210gms ) high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed pipe all complete complete all as specified and directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

THE SUPPLY AGENCY

M/S SANTOSHI TRADERS

M/S DHAR AND DHAR

jawaharlal jaiswal and co

M/S GOPAL ROY AND CO