Supply of spare parts for Cattle Feed Plant

Pallet Mill die 8mm hole Super Senior extra wide Size: 630 mm OD 520mm ID 222 mm Phase, 17 Rows of Holes with straight caller & m-20x12 holes both sides on 565 PCD

Roller Shells “V” grooved for above Size 250mm OD 180mm ID(Suitable for Bearing no. 32220, 182 mm wide

Roller Assembly Complete with shell & Bearing etc. Bearing SKF/FAG/ZKL

Die Holder Assembly Complete with “T” Shaft, Bearings 32324 & 32224, Bearing covers, Oil Seals etc. Bearing SKF/FAG/ZKL

Die Holder only (Alloy Steel Forging)

“T” Shaft with centralized greasing system

Spare for Roller Assembly (Cover Set)

i) Eccentric Shaft (Alloy Steel)

ii) Middle Spacer 51 mm wide

iii) Bearing Cover Plate

iv) Bearing Pressing Plate

v) Circlip 180 mm Inner

vi) Lock nut for Eccentric Shaft m-20

vii) Lock Nut Washer for above MB-20

viii) Clamping Device (Setting Ring of male female rings)

ix) Centre Bolt for roller Alen Type (Unbreako/ TVS/LPS)

x) Nut for Centre Bolt Attached with 1 male ring & Pin

Front scraper assembly

Stud for front scraper assembly

Roller locking Assembly with Two Disc and master plate

Share Pin Block

Share Pin 18 mm Dia

Paddles for conditioner of 330 mm die of SS-304 with Stud and Nut

Die Ring rear for Straight collar die (Alloy Steel EN-9)

Die Ring front for Straight collar die (Alloy Steel EN-9)

Die cover with 4 Hooks size 520 OD x 340 mm ID x 130 mm wide made of SS 304 x 3 mm thick plate SS-304

Main Bearing cover Plate front with Oil Seal 180-150-13 for Bearing 32324

Main Bearing cover Plate Rear with Oil Seal 170-150-13 for Bearing 32224

Main Bearing Pressing Ring front

Main Bearing Pressing Ring rear

Pallet Die Guard Assembly with Pallet cutter made of 6 mm thick SS 304 Plate

Feeder Complete with screw about 02 Meter long 400 mm Dia

Pallet Mill Main Pully SPC Section 9 Grove x 1220 mm Dia close grain CI Dynamically balanced +- 2 Grms.

Pallet Mill Counter Pully SPC Section 9 Grove x 230 mm Dia close grain CI Dynamically balanced +- 2 Grms.

Die Bolt 20x50 mm High Tensile (Unbreako/ TVS/LPS

Die Bolt 20x140 mm High Tensile (Unbreako/ TVS/LPS

Die Bolt Washer (Spacer)

Bush for “T” Shaft (Roller Holding Bush)

Elevator Belt 10” 4 Ply

Elevator MS Bucket 8*5, 3 Hole

Elevator Bucket Bolt(3*8, 1 1/2)

Twin Rotor With Motor 10 HP Complete

Fidder Condisnior Soft Complete SS 2 Mtr.

Sprocket Duplex 1" 10 Teeth

Sprocket Duplex 1" 14 Teeth

Sprocket Duplex 1" 18 Teeth

Sprocket Duplex 1" 19 Teeth

Sprocket Duplex 1" 25 Teeth

Sprokit Duplex ¾" 14 Teeth

Sprocket Duplex ¾" 95 Teeth

Sprocket Duplex 1" 50 Teeth

Side Glass 200 MM PVC Round

Vindish charger 3 HP Motor With Gair Box Complete

Elevator Botom Drum Complete With Bearing 4mm seet

Pellet Mill Hopper SS Make

Pellet Bin SS Make 4 MM Seet 6 M.T.

Pellet Mill Cover SS 5 MM Seet with Gard Complete

Molasses Pump 4" With Flench Complete

Molasses Pump 2" With Flench Complete

Hammer Mill Beater size 140 x 60 x 6 mm thick

Hammer Mill Sieve 5 mm Hole perforation size about 880 x 720 x 3 mm thick

Hammer Mill Beater Holding Rod 18 mm Dia

Hammer Mill Beater Spacing Bush

Elevator Top Drum about 600 mm Dia x 300 mm width complete with shaft about 800 mm length x 50mm Dia suitable for Bearing 1211 K

SS 304 Wire Mesh For Vibro 5MM OPG x 1.50 MM Dia Size 72” x 72”

Chain Conveyor Chain size 285

Chain Conveyor Chain size 385

Chain Conveyor Sprocket 9 teeth with shaft 50 mmx600 mm

Chain 1" simplex

Elevator Jacket 300x290 mm

Pellet Cooler Blower Impeller S.S with soft and bearing

T-Shaft Gun Metal Bush

Slate Conveyor Chain

150 HP Motor Bes Frem

Slate Conveyor Sprocket

Motor with Gair Box 5 HP-127 RPM PBL

Motor with Gair Box 10 HP-127 RPM PBL

Pipe 10 Inc. S.S 2 mm Thickness S.S.

Motor 3 HP- 15 RPM PBL

Pully 14” 2 Group B Section

Pully 3” +4” 2 Group B Section

Sprokit 15 Theeth Duplex ¾

¾ Duplex Chain

Duplex Chain 1" Roller

Joot Separator

Pellet Cooler Assentric

Pellet Sheev Jaali 6 mm SS

Chain Conveyor Roll

Acy Dray 5 HP 3 Face

Back Chain Conveyor Set Complete (285)

Pellet Sheev (10 M.T. Per Hour. S.S.) Complete With Motor

Sprokit Duplex 1’’ 76 Thickness

Pellet Coller S.S. 3 mm Thickness Complete 304 S.S. Hoper- S Presson Line Complete 400 mm 3 mm Thicknes

The Gas and Metal Operators

Mechserve Engineering