SPECIAL REPAIR TO BLDG NO 206, P 923, CERTAIN ROOMS OF GCA DISPLAY AND BLAST PEN INSIDE WALL AT Y 7, SE BLAST PENS AND DE BLAST PENS AT AF STN UTARLAI

Amount

Demolition of Concrete in ground floors and paving n exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Demolition of Concrete in ground floors and paving exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors laid over and including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations,filling and mass concrete/ sub base of floor, complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type -B-0 (using 12.50 mm graded stone aggregate) as in floor, finished the surface even and rough complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for Glazed coloured ceramic tiles in vertical surface 450x 350x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles complete all as specified and directed.

M&L 10 mm thick cement plaster backing of walls tiles in cement mortar 1:4 finished even and fair, complete all as specified and as directed.

Taking down cement or cement lime plaster from concrete surface,brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement. completed all as specified and directed

Demolition of pre-cast PCC block walling / brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed

M & L for block masonry with solid pre-cast cement concrete blocks made out of cement concrete 1: 3: 6 type C-1, using 20 mm graded crushed stone aggregate, exc. 10 cm in width and setting in cement mortar 1 : 6, complete all as specified and directed

M & L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of old plastered or un-plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M & L for preparation of old plastered or un-plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connections complete all as specified and directed.

S & F 15 mm bore steel water tubing "medium grade" galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

Taking up or down 20 mm bore steel water tubing and connections complete all as specified and directed.

S & F 20 mm bore steel water tubing "medium grade" galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S & F in repairs Vitreous China urinals, half stall urinal, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) ,complete all as specified and directed.

S &F in repairs Vitreous China one piece European Water Closet of size715mm x 375mm x 795 mm snow white, colour including P trap and twin flushing cistern with duroplast slim seat cover Cat No S1013139P Make Cera and equivalent makes:- Hindware, parryware , complete all as specified and directed.

S &F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type, flushing cistern 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets and 32 mm dia PVC flush pipe suitable length and making all connection and making good disturbed surface complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated Health Faucet With 1 Metre Flexible Tube and Wall Hook - Set of 2, suitable for-pedestal pattern water closet Cat No F160023,Make Hindware and equivalent, CERA, parryware , complete all as specified and directed

S & F in repairs vitreous china wash hand basins white, flat back, size 550 x 400mm including stainless steel 32 mm dia waste coupling, brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified

S & F in repairs wall hung vitreous china wash basins with full pedestal snow white flat back, size 550 x 400 X 290mm Cat No S2040105 wash basin, S2090101 full Pedestal Make Cera and equivalent to Hindware, parrywarecomplete all as specified

S & F in repairs cast copper alloy chromium plated fancy type 15 mm bore bib tap with crutch or butterfly handle , screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 15 mm bore bib tap with screwed down, screwed for iron pipe or for brass ferrule, long nose with flange and aerator , model No F2002152 , Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 15 mm bore bib tap with screwed down, screwed for iron pipe or for brass ferrule, with wall flange and aerator , model No F2002151 , Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated fancy type 15 mm bore 2 way bib tap with screwed down, screwed for iron pipe or for brass ferrule with wall flange and aerator , model No F2002163B , Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 15 mm bore dia pillar taps, with capstan heads,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S & F in repairs stainless steel chromium plated, fancy type, 15 mm bore dia pillar taps with , screwed for iron pipe , caabul (stain SS) 374 mm long , model No F1031302 , Make Cera and equivalent to Hindware, parryware, complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 15 mm bore dia Angle cock with wall flange and aerator model No F8040204 ,Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 2 way Angle cock with wall flange and aerator model No F2002211 ,Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, Urinal spreader fixing with 15 mm dia pipe. , complete all as specified and directed. Make :- CERA, Hindware, parryware

S & F in repairs cast copper alloy chromium plated, fancy type, Urinal spreader fixing with 15 mm dia pipe model No F8070201 ,Make Cera and equivalent to Hindware, parryware , complete all as specified and directed.

S & F in repairs cast copper alloy chromium plated, fancy type, 15 mm bore dia self closing angle cock prismatic for urinal with wall flange and 200 mm connecting pipe model No F9020203, Make Cera and equivalent to Hindware, parryware, complete all as specified and directed.

S & F in repairs 450 mm long PTMT connection with two brass nuts chromium plated internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed.

S & F in repair shelf for WHB made out of white acrylic sheet of size 125 mm x 450 mm fancy type including fixing arrangement etc complete all as specified and directed.

S&F for grating stain less steel 100 mm dia , complete all as specified and as directed.

S&F towel rail 600mm long of stainless steel fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S & F in repairs stainless steel soap dish of standard size complete all as specified and directed.

S & F in repairs non locking single roll toilet tissue dispenser and paper roll holder satainless steel of standard size complete all as specified and directed.

S & F 32 mm dia PVC pipes single socketed, in any length with rubber ring joints, fixed in urinal, wash hand basin etc. complete all as specified and directed.

Demolition and breaking up drain pipes 100/75 mm bore (PVC / Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified.

S&F 75 mm bore PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls or floor, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend any radius including jointing with solvent cement complete all as specified and directed.

S&F 75 mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified

S&F 110 mm bore PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any radius including jointing with solvent cement complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F 30 mm thick (style thickness) Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, Fixing in as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made solid PVC door frame of size 50 mm X 47 mm made out of 5 mm thick single side prelam PVC sheet reinforced with mild steel square tube and edges will be painted to match with prelam sheet as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

Taking down chowkhats or frames area exceeding 1.50 sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified complete all as specified

S & F mild steel mortice lock vertical type size 100mm 4 levers complete all as specified and directed .

S&F door closer hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminium body (die cast) weight between 61 to 80 kg complete all as specified and directed .

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed , complete all as specified

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section , complete all as specified

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 150 mm long Aluminium handles, cast type, anodised , complete all as specified and directed.

Taking down steel shutters with frame of any description, area not exc 1.50 Sqm each complete all as specified and directed .

S&F factory made steel ventilator with top hung shutter including box type hinges , mild steel handle & peg stay with or without glazing bar complete all as specified and directed .

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E, complete all as specified and directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed.

S & F for galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in repairs for 40mm bore brass chromium plated bottle traps for urinal with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Formwork to edges (rough finished flat surfaces ) of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

M&L for RCC1:1.5:3 (Nominal mix) type A-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

M & L for mild steel ,TMT bars 10 mm dia and above , cut to length, bent to shape required, including cranking, bending spirally for hooping, hooking ends and binding with MS wire (annealed) not less than 0.90 mm dia or securing with clips quality conforming to Fe-410-S or Fe-410 -0 ,complete all as specified and as directed.

Ditto all as per item No. 75 above but 5 mm dia and over and including 10mm dia as in stirrups spacers and binder complete all as specified and directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

S&F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling all as specified

S&F 12 mm thick Perforated particle board/ tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples or on snap grid as in ceiling , complete all as specified and as directed.

S&F in repair 12 mm thick Perforated particle board/ tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples or on snap grid as in ceiling , complete all as specified and as directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section ( framed work) , complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position ( framed work) , complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails , complete all as specified and as directed.

M&L for 18/19 mm tick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

M&L for 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 13 Sqcm but n. exc 25 Sqcm. complete all as specified and directed

M&L for 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 3 Sqcm but n. exc 6 Sqcm. complete all as specified and directed

M&L timber framed 2nd class hard wood clean swan in scantling complete all as specified and directed

M & L for preparation of new/ old plastered or un-plastered surfaces of ceiling / false ceiling board and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparation of new/ old plastered or un-plastered surfaces of ceiling / false ceiling board / wall board and applying two coats of synthetic enamel paint over a coat of pink primer, of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

M&L for Cutting holes in stone walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required ,depth of embedded portion of hold fast or lugs exc. One brick but not exc two brick from the face of the jamb in to the wall complete all as specified

M&L for Cutting chases, pinning in stone , concrete block or slab walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth , complete all as specified

M&L for Providing, cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified

S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410- W(Gde- E-250) quality- B, complete all as specified and as directed.

S & F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

M&L for preparation of old steel surface and applying one coats of synthetic enamel paint of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

M & L for preparation of old wood surface and applying one two coat of synthetic enamel paint of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

M & L for preparation of old plastered or un-plastered surfaces of wall and applying two coats of distemper oil emulsion, of any description, , complete all as specified and as directed.

S & F for 20 mm thick granite for urinal partition of size 310x700 mm fixed in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite wall, complete all as specified and as directed.

S & F in repairs corner glass shelf of size 300 x 300 mm , model No F5005103 ,Make Cera and equivalent to Hindware, parrywere, complete all as specified and directed.

M&L for stone Walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted,built in cement mortar 1: 6 complete all as specified and directed

Demolition of Concrete in Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M & L PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping or similar work etc including necessary form work complete all as specified and directed.

M & L PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in Cement concrete in surface channels and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends, complete all as specified and directed.

M&L for 20 mm thick rendering in CM 1:4 on fair faces of stone surfaces finished even and smooth without using extra cement complete all as specified and directed. fair and even complete.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth without using extra cement, completed all as specified and directed

M&L for applying two coats of cement base paint over a coat of primer on newly plastered surfaces of walls including preparation of new surfaces complete.

M&L for two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described not exc 10cm width or girth, complete all as specified and as directed.

Surface dressing n.exc 15 cm deep in soft/ loose soil on top surface of filled up earth of traverse of blast pens, complete all as directed.

Supply and stacking of approved soil/ earth out site defence land and deposited at blast pen/ traverse wall in tech area ( The soil shall be used filling against item Ser No 18), complete all as directed.

Levelling of top surface of blast pens by using approved soil ( The soil stacked at the base the same blast pens/ traveres wall obtained from ser item No 111 & 113 shall be used) in layers n exc. 30 cm thick; watering, ramming and finishing to required size, shape, etc., The levelling work shall be carried out from base of the blast pen up to top height varying from 0.00 mtr to 10.00 mtr.

Rough excavation and stacking the soil at the base of the same blast pens/ traverse wall not exceeding 1.5 m deep and getting out soft/ losse soil, complete all as directed.

Supply for loose filling back of wall for invert filler of gauge 20mm to 12.5mm grade (stone brocken aggregate) , complete all as directed.

Supply for loose filling back of wall for invert filler of gauge 40mm to 80mm grade (stone brocken aggregate), complete all as directed.

Raking out old joints/ pointing to random rubble or polygonal rubble or brought up to course, complete all as specified and directed.

M & L for raised pointing with using cement mortar 1:3 to random or polygonal rubble, uncoursed or brought upto courses, complete all as specified and directed.

Drilling /Cutting holes in through RCC wall for inserting 12 mm to 20 mm dia bar for hold fasts length exc 300mm but not exc 450mm and making good all disturbed work to match the existing. complete all as directed. Note : Drilling work shall be carriedout to blast pen/ traverse wall of 6 mtr to 10 mtr height. All safety measures shall be taken by the contractor as per safety code

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 22.5 cm and not exceeding 30cm long and 16mm to 20mm dia bolt, complete all as specified

M&L for restraining resecuring including making good existing 3 to 4 mm dia plain wire fixed to gable end of blast pen of above 6 mtr height including tying at crossings with mils steel wire staples or pins, PVC staples etc complete all as directed (each line of wire to be measured)

S&F in repair 4mm dia of wire Plain mild steel wire, galvanised class 3, in any postion including straining and fixing to steel post and / or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured)

M&L Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete less than 25 cm , including necessary form work complete all as specified and directed.

M & L for 50 mm thick PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floor finished the surface even and smooth without using extra cement, complete all as specified and directed.

M & L for 75 mm thick PCC1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for hardcore Broken stone or bouldersof gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed.

M&L for Forming construction joints 30mm deep x 10mm wide filled with sealing compound of grade 'B' complete all as specified and directed.

M&L for Forming contraction (Dummy) joints 35mm deep x 10mm wide filled with sealing compound of grade 'B'complete all as specified and directed.

M & L for 100 mm thick PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floor , complete all as specified and directed.

M&L for cement concrete 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in foundations,filling and mass concrete , complete all as specified and directed.

M&L for 150 mm thick cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in path/floor with and incl use and waste of form work and finishing the surface even and fair including necessary form work complete all as specified and directed.

M&L for Vitrified Ceramic tiles 10 mm thick light shad (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, and laid over & including 15 mm thick screed bed in CM 1:6 etc. , complete all as specified and directed.

Ditto all as per item ser No 131 Above but as in skirting / dado laid over & including 10mm thick cement plaster in CM 1:4 , complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming and finishing to required size, shape, etc., n exc. 1.5 m high from base of travers wall obtained from ser item No113 shall be used all as specified.

M&L for Drill the holes of 12mm dia up to 100 mm deep and fixing nozzel of 10mm dia with hardner chemical ( CICO No 3 and equivalent) & cement to RCC wall/ ceiling and Inject the polymer based cement grouting materials in the nozzel with pressure and seal the nozzel complete as per manufacturer's instruction , including necessary arragement the scaffolding , height varying from 0.00 mtr to 7.00 mtr. complete all as specified and directed.

M&L for Grouting 50 mm thick under stanchion bases or grillages, etc. including any temporary shuttering to edges with cement mortar 1:2

S & F GI chicken wire mesh of 0.71 mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas/facias/ columns ,beam ,concrete wall / ceiling etc complete all as specified and directed

M & L for Dubbing out average 10mm thick CM 1:4 on irregular face of old walls/ ceiling,complete all as specified and directed Note: The work shall be carried out from base of the blast pen up to top height varying from 0.00 mtr to 7.00 mtr.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surfaces of wall with cement mortar 1:4 finished even and smooth without using extra cement, completed all as specified and directed. Note: The work shall be carried out from base of the blast pen up to top height varying from 0.00 mtr to 7.00 mtr.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surfaces ceiling with cement mortar 1:3 finished even and smooth without using extra cement, completed all as specified and directed. Note: The work shall be carried out height varying from 3.00 mtr to 7.00 mtr of blast pen.

M&L for preparation on new plaster surface of ceiling & applying three coats of white wash complete all as specified and directed

Raking out of old bituminous of any description from existing expansion joints of dimensions 25mm to 30mm wide and 50mm deep removing the debris from site, treating sides and bottom of the joints with primer refilling the joints with bituminous grade 'B' complete all as specified and as directed.

Taking down roof treatment any type any description on top of roof complete all as specified and directed

M&L for cement concrete (1:2:4) type B-0 using 12.5mm stone aggregate as in roof padding benching kerbs of mud stops, rounded or chamfered on edges including form work complete all as specified and directed

M&L for rendering 10mm thick in cement mortar (1:4) on concrete surface as on roof slab, finished even and smooth without using extra cement mix with water proofing compound as per manufacturer instruction complete all as specified and directed . Note: WPC shall be measured and paid sepratelly.

Supply only Integral waterproofing compound

M&L for applying roof treatment on top of roof with 3mm thick APP modified membrane with non woven polyester reinforcement/ mat (centre core) shall be laid by torch application method with overlap 100mm on length side and 100mm on width side including a coat of bituminious oil based primer ( IS : 3884) @ 250gm / Sqm complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. complete including making good the disturbed surfaces of walls, ceilings as per existing specification complete all as specified and as directed.

M & L for point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded FRLS flexible copper conductor cable in and incuding rigid PVC conduit concealed with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch including 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in stone/block wall , replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge. Note: (i) Unit rate shall be included for cutting chases for conduits and sunken boxes and making good to wall, floors etc

M & L for point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded FRLS flexible copper conductor cable in existing concealed conduit with replacement of pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of existing size/shape for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, complete all as specified and directed by Engr-in-charge.

-ditto- all as per item Ser No 149 above but one 3 pin 5 Amp socket outlet on independent board complete all as specified.

-ditto- all as per item Ser No 149 above but for one 3 pin 5 Amp socket outlet on same board complete all as specified.

M & L for point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in existing concealed conduit with replacement of pressed steel terminal boxes of adequate size fixed flushed to the wall with 3mm thickness plastic laminated sheet cover of existing size/shape for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 sqmm FRLS,PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, including cutting chases in brick wall, replastering and making good to match the existing specificationscomplete all as specified.

M & L for point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded FRLS flexible copper conductor cable drawn in and incl PVC casing caping with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly complete all as specified and directed by Engr-in-charge.

-ditto- all as per item Ser No 153 above but for One 5 Amps socket point controlled by switch on the same board with other switches complete all as specified.

S&F switch piano flush button single pole one way 5 Amps 230 Volts,complete all as specified and directed by Engr-in-Charge.

S&F socket outlet 5 Amps 5 pin flush type, 230 Volts, complete all as specified and directed by Engr-in-Charge.

S&F Switch socket combination 2 in 1, 5 pin, 5 Amp flush type.

S & F Switch socket combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal complete all as specified.

S&F fan regulator electronic flush type stepped (rotary type) with 5 steps speed control complete all as specified

S&F ceiling rose surface bakelite three terminal isolated body fixed on PVC round block complete all as specified.

S&F LED tube light fitting 1x20w,230v, including LED tubular lamp (tube rod) , 4 feet batten fitting fixtures, complete with all accessories internally pre-wired and including connecting up with two core flexible copper conductor cable of suitable size complete all as specified

S&F of slim LED batten light fitting 1x9w,230v, 2 feet fixtures, complete with all accessories internally pre-wired and including connecting up with two core twisted flexible copper conductor cable with suitable size complete all as specified.

S & F LED light fitting (2x2 feet) size recessed type 42watt, environmental friendly energy efficient complete with all accessories prewired and including connecting up with 3 core flexible copper conductor cable with suitable size complete all as specified.

S & F sheet metal powder coated versatile double door tripal pole and neutral (TPN) distribution system for MCB provisions, 415 volts, 50 Hz AC supply 4 way fitted with two cover with copper bus bar rated 200 amps neutral link, earth bar and din rail complete all as specified.

S & F MCB TPN 63amps complete all as specified.

S & F sheet metal enclosure powder coated versatile double door single pole and neutral (SPN) distribution board system for MCB provisions, 230 volts, 50 Hz AC supply 4 way fitted with two cover with copper bus bar rated 200 amps neutral link, earth bar complete all as specified.

-ditto- all as per item Ser No. 166 but for (SPN) DBs 08 way complete all as specified.

-ditto- all as per item Ser No.166 but for (SPN) DBs 12 way complete all as specified.

S&F in replacement MCB single pole and neutral (SPN) 63 Amps complete all as specified and directed.

S&F in replacement MCB single pole and neutral (SPN) 40 Amps complete all as specified and directed.

S&F in replacement MCB single pole and neutral (SPN) 10 to 32 Amps complete all as specified and directed.

S&F in replacement MCB single pole (SP) 6 to 20 Amps complete all as specified.

S & F in raplacement of existing submain wiring with two runs of single core FRLS PVC insulated and unsheathed cable with copper conductor multi stranded having nominal area 2.5 Sqmm drawn through existing conduit concealed type and making electric connections including one run (FRLS) PVC insulated singlr core conductor cable 2.5 sqmm as a earth continuity conductor drawn through existing PVC conduit including cutting chases in brick wall wherever necessary, replastering and making good to match existing specification complete all as specified and directed by Engineer - in – Charge. Note : 2 run of 2.5 Sqmm single core FRLS PVC insulated copper conductor cable and 1 run of 2.5 Sqmm copper conductor earth wire will be measured as one unit.

-ditto- all as per item Ser No. 173 but for with 2 runs of 4sqmm and one run of 4sqmm as earth cuntinuity conductor complete all as specified.

-ditto- all as per item Ser No. 173 but for with 2 runs of 6sqmm and one run of 6sqmm as earth cuntinuity conductor complete all as specified.

-ditto- all as per item Ser No. 173 but for with 2 runs of 10sqmm and one run of 10sqmm as earth cuntinuity conductor complete all as specified.

S & F in raplacement of existing submain wiring with two runs of single core FRLS PVC insulated and unsheathed cable with copper conductor multi stranded having nominal area 2.5 Sqmm drawn into and including PVC casing caping of adequate size and making electric connections including one run (FRLS) PVC insulated single core conductor cable 2.5 sqmm as a earth continuity conductor drawn in and including PVC casing caping including cutting chases in stone masonry wherever necessary, replastering and making good to match existing specification complete all as specified and directed by Engineer - in – Charge. Note : 2 run of 2.5 Sqmm single core FRLS PVC insulated copper conductor cable, 1 run of 2.5 Sqmm copper conductor earth wire and one run of PVC casing caping will be measured as one unit.

-ditto- all as per item Ser No. 177 but for with 2 runs of 4sqmm and one run of 4sqmm as earth cuntinuity conductor complete all as specified.

-ditto- all as per item Ser No. 177 but for with 2 runs of 6sqmm and one run of 6sqmm as earth cuntinuity conductor complete all as specified.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of SI Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthing wire)

Supply & fix exhaust fan AC single phase 230/ 240 V of size 300 mm sweep 900 RPM steel body, grouted with anti vibration bush and with louver including PVC copper cable 1sqmm three core connecting from ceiling rose to exhaust fan terminal complete all as specified ans directed. Note:- Exhaust fans shall be ISI marked & having three star rating.

Taking down old unserviceable aluminium/GI strip of any size with saddles screws etc for roof conductor/down conductor including damaged cement concrete block above ground/down conductor up to test point complete all as specified.

Taking down old unserviceable earthing material burried in ground including old GI strip, earthing plate complete all as specified.

S&F in repairs Test Point Terminal Block made of Gun Metal or Phosphorus Bronze size 75x75x25mm, drilled and screwed including 3 Nos. 8mm dia, 25mm long hexagonal Head Screw complete all as per specified and as directed.

S &F in repairs air terminal single pointed aluminium rod of 12mm dia and 300mm long with GI steel tubing 40mm bore, 1.5 mtr long light grade including & fixed on PCC 1:2:4 using 20mm graded stone aggregate block of size 300x300x300mm and necessary fixing arrangement at roof complete all as specified and directed. Note:- If threaded of GI tubing is damaged then contractor will be responsible for cutting of thread for fixing of GI tubing.

S&F Aluminium Strip 25 x3 mm thick with Saddles and fixing Screws for Roof/ Earth Conductors and all Joints should be connected by Exothermic Welding or Brazing complete all as specified and directed. NOTE : All Joints should be joined by Brazing by using of nuts and bolts near test point.

S&F Galvanised Iron Strip 32x6mm thick for earth pit to earth pit grid connecting in ground in buried ground including earth work complete all as specified and directed.

Supply and lay Low density poly ethylene pipes (LDPE) of pressure size 40 mm dia laid in trenches complete all as specified and directed.

M & L for Earthing complete with Galvanised Steel earthplate of size 60x60cmx6mm thick electrode and 32x6mm GI strip as earth lead, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below ground level, connected to 32x6mm earth strip by means of nuts, bolts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I(2009), Earthing strip shall be protected by GI or steel pipe 40mm bore light grade and connected to continuous earth wire on pole/test point. watering shall be 20 mm bore GI medium grade. The earthing shall be inclusive of excavation & earth work in any type of strate, soil,, charcoal, salt, funnel PCC pit and RCC cover complete all as specified & tested complete and making a good surface of existing PCC hard standing/surface area complete all as specified.

M & L for shifting of existing LT panel board from near toe wall to 2mtr distance in back side including earth work and PCC (1:3:6) type C-2 using 40 mm garded stone aggregate as per existing height/size for panel grouting, rerouting of LT cables of different sizes with lugs complete including making good disturbed surfaces area all as specified and directed.

S & F recess mounted aesthetic LED undercanopy luminaries 80w comprises of pressure die cast housing & frame with toughened glass, IP66 protectiuon complete with all acessories internally prewired and including connetcting up with twin core twisted flexible copper conductor cable with suitable size complete with arrangement at the site all as specified make:- crompton, model:- Neptune cat part No LCN-80CDL or equivalant to Bajaj/philips

S & F in raplacement of existing submain wiring with two runs of 4sqmm single core FRLS PVC insulated and unsheathed cable with copper conductor multi stranded drawn through rigid non metallic PVC conduit and making electric connections including one run (FRLS) PVC insulated single core conductor cable 2.5 sqmm as a earth continuity conductor including cutting chases in brick wall wherever necessary, replastering and making good to match existing specification complete all as specified and directed by Engineer - in – Charge. Note : 2 run of 4 Sqmm single core FRLS PVC insulated copper conductor cable, 1 run of 2.5 Sqmm copper conductor earth wire including PVC conduit will be measured as one unit.

Taking down unserviceable main switch/DB/MCB including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed.

S & F sheet metal enclosure for fixing MCB's TPN with 200amps rated neutral bus bar 415 volts, 8 ways with double door fixed on flushed to the wall including making the hole in the wall and fixing the DB including cement work and plaster complete all as specified and directed.

S&F MCB Triple pole and neutral (TPN) 100 Amps, 415 volts complete all as specified and directed.

S&F in replacement of triple pole and earth enclosure with a 3 pin and earth plug with socket complete with triple pole MCB 32 amp capacity complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded FRLSH flexible copper conductor cable drawn through in and incl stove enamelled steel conduit 20mm dia with all acessories like sockets, bends, junction box etc. fixed on wall/ceiling with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in stone/block wall , replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge. Note: (i) Unit rate shall be included for cutting chases for conduits and sunken boxes and making good to wall, floors etc

-ditto- all as per item Ser No. 197 but for one 3 pin 5 amps socket outlet on same board complete all as specified.

-ditto- all as per item Ser No. 197 but for one 3 pin 5 amps socket outlet on independent board complete all as specified.

-ditto- all as per item Ser No. 197 but for with 4sqmm cable for one 15amp socket outlet point on independent board complete all as specified.

M & L for point wiring with 2.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded FRLSH flexible copper conductor cable in and incl stove enamelled steel conduit 20mm dia with all acessories like sockets, bends, junction box etc. fixed on wall/ceiling with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch incl 2.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in stone/block wall , replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge. Note: (i) Unit rate shall be included for cutting chases for conduits and sunken boxes and making good to wall, floors etc

S & F for submain wiring with two runs of single core FRLSH, PVC insulated & unsheathed cable with copper conductor multi stranded having nominal area 4 Sqmm drawn into and including steel conduit of 20mm dia with all acessories like sockets, bends, junction boxes etc fixed on walls with one run (FRLSH) PVC insulated single core conductor cable 4 sqmm as a earth continuity conductor including cutting chases in stone masonry wherever necessary, replastering and making good to match existing specification complete all as specified and directed by Engineer - in – Charge. Note : (i) 2 run of 4 Sqmm single core FRLS PVC insulated copper conductor cable, 1 run of 4 Sqmm copper conductor earth wire and one run of steel conduit will be measured as one unit.

Godara Construction and General Suppliers

M/S HARIOM CONSTRUCTION COMPANY

M.D. CONSTRUCTION CO.