SPECIAL REPAIRS TO BLDG NO ETA 83 STUDENT JCO MESS OF ASC CENTRE AND COLLEGE UNDER GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of debris outside MoD land and depositing where directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chaj-jas and similar sus-pended work (reinforcement cut as required to facilitate demolition) including removing of debris as ordered outside MD land complete all as directed.

Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 5 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Dismantling wall and ceiling board fibre, uplp insulation etc or insulation boards any thickness including cover fillets complete all as directed.

Dismantling of AC Corrugated or semi corrugated sheet etc any thickness including ridges as in roof covering and stacking at site where directed and removal of debris to a outside MOD land and depositing where directed complete all as directed.

Dismantling boarding, any description, fixed in any position with nails and stacking at site where directed for Credit.

Dismantling of timber scantlings 40 Sq cm and over in section in any position unframed work and stacking at site where directed complete.

Dismantling of wooden battens for tiles of any size including tiling fillets exe 15 cm spacing complete and stacking where directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Excavation in trenches and not exe. 1.5 m wide and not exe. 1.5 m in depth for foundation of drain, man hole , laying of UG cables etc. not exe. 10 Sq. m on plan and not exe. 1.5 m depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft rock complete all as specified and directed

Removing excavated surplus soil to a distance not exceeding 50 mts and depositing where directed .at a level not exceeding 1.5 M above the starting point complete all as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

All same as per item No 17 here-in-above nut not exceeding 10 cm thick -do-

Providing plane ce ment concrete Type B1 1:2 :4 using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts , boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 complete all as directed.

M&L for Type B0 1:2:4 (12.50 mm graded aggregate) providing cement concrete as in back filling of chowkats , plinth courses string courses etc . complete all as specified and as directed.

M&L for cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as required, exc half brick & not exc one brick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall).

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

M&L Second class hard wood well seasoned wooden scantling clean sawn framed & fixed to walls or timber frame fixed with screws complete all as directed.

S&F 20mm thick second class hardwood boarding, fixed with nails in any situation (except flooring and skirting), Planed one side with butt joints, complete all as specified

All same as per item No.24 here -in - above but except wooden boarding - (Note : wooden boarding obtained from item No 09 here -in - above)

M&L for Second class hard wooden battens spaced at 30 cm centre to centre clean sawn cross sectional area exceeding 5 sqcm but not exc 15 sqcm complete all as directed.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed

dS &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge.

S & F factory made UPVC white colour sliding window three track made of extruded profile with wall thickness of 2.3mm (+-0.2mm) window profile with hollow section with multi chamber. Frame (88mmx52mm), sliding sash (42mmx67mm). Sliding mesh sash (42mmx57mm) Sliding interlock (one vertical length in each shutter)(45.5mmx28mm) glazing beads (24.5mmx 16mm) will be mitred cut and fusion welded at all corners incl drilling of holes for fixing hardware and drainage of water etc making arrangements for fixing of 5 mm thick plain sheet glass ordinary quality with hardware EPDM gasket 1.2+-0.2mm thick galvanised steel frame (30mmx 18mm) 2 Nos, sliding mesh sash (26mmx10mm) profile to be inserted in required profile frame will be fixed to the wall with 8mmx100mm long fasteners Hardware (touch lock of zinc alloyed (white powder coated) steel roller system stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and required accessories area n.exc 2 sqm each. ( Note :(i) Quoted rate is deemed to be inclusive of 5 mm thick sheet glass & SS wire cloth and includes all other connected accessories.(ii) Net opening will be measured for payment purpose)

S&F100 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 100 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S & F in repair mild steel powder coated body stopper with hard drawn steel spring , 150 mm size fixed to door complete all as specified

S & F mildsteel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified

S&F in repair 25mm dia aluminium anodised decorative type curtain rods along with brackets & dome.

S&F in repair decorative type curtain rod with brackets & dome .

S & F in repairs brass chromium plated tubular towel rail, 20mm dia ‘D’ type, 600mm long between flanges complete all as specified and directed.

S&F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified.

Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed.

S & F for 4 mm thick of size 600mm x 600mm HSPC (High pressure steam cured) pre-primetered self embossed, textured designer board E-Board Classic( White colour) to be fixed and including GI based frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screw at 450mm centre to centre/ intermediate channel 09mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with & incl ceiling section(n.exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre suspended with 6 mm dia GI barhangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purline from the roof with alignment clip including providing provision for light fixtures of any size complete all as specified.

M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of floor/ foot path etc and finished the surface complete all as directed.

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.118 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 350x250x7mm / 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 51 & 52 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over and including 15 mm thick screed bedding in cement mortar 1 : 4 including Rounding to edges complete.

All same as per item No 53 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 53 & 54 : i) Quoted rate is deemed to be inclusive of cement screed.)

M&L for 20 mm thick Granite (of any type) machine cut work as in skirting , dado , urinal partition etc as ordered jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting and polishing (mirror polish i.e. full granite polish as per local trade practice) all as specified & directed

M&L for 20mm thick Granite slab machine cut of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin all as specified & as directed

M&L M-35 grade, 60 mm thick machine pressed, PVC moulded precast cement concrete interlocking paver blocks any shape and size with grey cement and pigment confirming to IS: 15658-2006, laid over and including 50 mm thick compacted sand cushion complete complete all as specified.(Note ; Quoted rate is deemed to be inclusive of 50 mm thick compacted sand cushoning).

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M & L for Rendering 15 mm thick in cement mortar 1:4 on internal concrete surface mixed with WPC @ the weight of minimum 3% by weight of cement mixed or as per manufacturer instruction , and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC measured and paid separately.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses masonry built in cement mortar or cement lime mortar all as directed

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M & L for 40 mm bore GI water tubing medium grade (ISI marked) with fittings such as bends, tees, elbows, nipples, unions, short pieces etc laid in trenches making necessary connection and testing on completion all as specified and directed..

All same as per item No 64 here-in-above but 25 mm bore of pipe -do-

S&F in repair 15mm dia cast copper alloy Bib taps, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repairs 15 mm bore angle valve , cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions

S&F in repair CP soap dish, approximate size 160x160x90mm fixed to plugs with chromium plated (CP) brass screws complete all as directed.

S&F 20 mm size Gun metal globe or gate valves (ISI Marked) conforming to IS 778 : 1984 with iron wheel head screwed box and both ends for iron pipe or union complete all as directed

All same as per item No 69 here-in-above but 25 mm size -do-

All same as per item No 69 here-in-above but 40 mm size -do-

S&F in repairs vitreous china oval counter wash hand basin white of size 520 mm x 450 mm with & including chromium plated pillar tap cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S&F in repairs vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F in repair 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repair 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints fixed to wallscomplete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F 110mm bore PVC (SWR) vent cowl jonting the same with solvent cement complete all as directed.

Taking down old rusted / wornout 20 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

Taking down old rusted / wornout 25 mm bore GI tubing after necessary disconnection & S&F new 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

E&M : Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing taken down materials to a place where ordered for crediting including making good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed..

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) on concelaed conduit conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / One fan point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5 Amp on independent board

(c) One 3 pin socket point 5 Amp on same board with other switches.(to be provide new point as user reqairment)

All as per item No. 86 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 6 pin 15 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way.

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose

Supply and fix Switch socket combination flush type 6/16 Amps 3/3 pin universal multipurpose

S&F ceiling rose surface bakelite White / Ivory / Urea finish 50 mm dia three terminals including supply and fix PVC square mounting block complete all as specified and directed.

Supply and fix fan regulator electronic , step & socket type 230 volts , suitable for 1200 /1400 mm sweep ceiling fan complete all as directed.

S&F of LED Luminarire 600mmx600mm 35/36 Watt , 230 volt, with recessed type with high efficiency PMMA diffuser soft glare free light complete with driver holders & LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm ,and old LED/FTL tube light fittings Deposit to store with all as specified and directed by Engr-in-charge.

S&F 20 Watt , 6000K, 230 Volt, 4ft Batten surface and wall mounted LED batten with aluminium housing with PVC housing & integrated electronic driver complete with all fixing accessories such as 2 nos of aluminium square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. .

S&F bldg security light light fittings 1x 35 Watt Ac 230v out door type LED street light with high pressure die cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistent including thermal managment in multiple optics complete , IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed.

S&F steet light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F submain wiring with 2 runs of 4 Sqmm single core PVC insulated, unsheathed, multi stranded copper conductor and one single core 4 Sqmm PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit/casing caping of size as ordered in walls / ceilings etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 4 Sqmm cable , one run 4 Sqmm cable and one run of PVC Conduit /Casing caping shall be measured as one unit length) .

All as per item No 99 here-in-above but 2 runs with 6 Sqmm single core cable and 6 Sqmm single core as earth contunity wire -do- . (Note :- 2 runs 6 Sqmm cable , one run 6 Sqmm cable and one run of PVC Conduit/Casing caping shall be measured as one unit length)

S&F in repair Sheet metal enclosure (ISI marked) distribution board for 415 volts, TPN 4 way Vertical type, double door, triiple pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S&F in repair Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, singal door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S & F in repair MCB TPN 40 to 100 Amps 415 volts, 'C' Series 10 kA rupturing capacity providing in DB complete and old MCBs Deposit to store with all as specified and directed by Engr-in-charge. Make Indoasian

S & F in repair MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB complete and old MCBs Deposit to store with all as specified and directed by Engr-in-charge. Make Indoasian

S & F in repair MCB single pole & neutral 40 Amps 240 volts, 10 kA rupturing capacity providing in DB complete and old MCBs Deposit to store all as specified. Make Indoasian

M&L for taking down and dismantling of ceiling fan 1200mm/1400mm sweep 230 Volt 50 C/S AC of any make or model by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing the bearing with similar type of exisitng one, worn out screws of the cover, split pin, twin core flexible copper wire of size 23/0.0076, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing etc, finally painting the ceiling fan with one coat of spray painting with white DUCO Paint & lettering & Numbering the same as per existing ,reassembling & testing the fan complete all as directed. Note :- (i) Spare Parts/accessories found unserviceable except bearing which are required to be replaced shall be measured and paid for separately under relevant items as “Supply only”. Rewinding shall also be measured & paid for separately (ii) Quoted rate is deemed to be inclusive of painting .

M&L for rewinding of ceiling fan of size 1200mm/1400mm sweep, 230 volt, 50 C/S, AC by removing of burnt winding from stator and rewinding the same with super enamelled copper winding wire of same gauge, same weight & turns including varnishing of winding & reassembling complete all as directed.

Supply & fixing and testing exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, metalic body , suitable for SP 230 / 240 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in any type of masonry wall to size by core cutting using core cutting machine & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan finally making good the disturbued surface of walls both internal & external to its original specifications to the satisfaction of Enginner-in-charge complete all as directed. Make : Havels Turbo Force SP or equivalent oin Bajaj/ CG / Orient / Usha as approved (Note : Quoted rate is deemed to be inclusive of core cutting to wall , including finishing the wall surface to its original specifications)

M&L for Sand cushioning/sand covering for underground cable protection complete all as specified. Note: Punned thickness only will be measured and paid.

Supply and laying sub class 'B' bricks of old size (standard size as per local availability) laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

S&Fmild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 50mm bore dia.

Supply, fixing ,Teting and commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of 25 Sqmm 4 Core all as specified and directed.

All as per item No 112 here-in-above but XLPE cable of size 16 Sqmm 4 Core -do-

M & L for Earthing to Main panel complete with galvanized steel earth plate electrode 600 x 600 x 6. mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4.0 mm dia as earthing lead of bolts,nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion including dismantling of old earthing materials.(for existing Main piller box)

M AND V ENTERPRISES (BID ID -3110280)

K. VENKATESH NAIDU (BID ID -3104077)