PROVISION OF 02X COVERED SHED GALVALUME SHEET OUT SIDE OF TEAM OFFICE IN ADM BLOCK P44 AT ROWRIAH41SAMinor11202425 PROVISION OF ALUMINIUM PARTITION WORK STATION AT MAIN OFFICE BLDG NO.P-5 AT SARAIBARI 41SARWMinor052024-25 PROVIS

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles and depositing off the rubbish materials where directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as directed

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as directed.

Taking up or down GI water tubing 15mm bore from trenches/ wall, ceiling or floors including all fittings, segregated and stacking the pipe complete all as directed.

Taking up or down GI water tubing 20mm bore from trenches/ wall, ceiling or floors including all fittings, segregated and stacking the pipe, complete all as directed.

Taking down old PVC PVC/ CI/ AC pipes of any dia on walls/ floors of any dia, complete all as directed.

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying GI pipe, cable etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and exc. 1.5m but not exc. 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying GI pipe, cable etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Returning filling in soft/ loose soil, including spreading, levelling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Material and labour for, earth filling in floors, laid in layers not exc. 25cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Material and labour for, sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Material and labour for, hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Material and labour for, loose filling with broken brick aggregates of gauge 40 to 80 mm in soakage pits, soakage wells, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in edging, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:2:4) type B-2 (using 40 mm graded crushed stone aggregate) for surface channel and drain, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) for holdfast/ bed block, complete all as specified and directed.

Material and labour for providing precast cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face and set in CM (1:4), complete all as specified and directed.

Material and labour for, RCC M25 (Design Mix) (using 20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material and labour for, RCC M25 (Design Mix) (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Material and labour for, RCC M25 (Design Mix) (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

Material and labour for, RCC M25 (Design Mix) (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:4), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size brick, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size, in one brick thick honey comb walling, built in cement mortar (1:4), complete all as specified and directed.

Material and labour for, cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing.

Supply and fix for, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

Supply and fix for, 75mm size butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 75mm long, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 100mm long, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 150mm long, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, extruded aluminium alloy handles, fabricated type, anodised 150mm size, complete all as specified and directed.

Supply and fix for, 150mm (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, 75mm size rim latch with two levers, of brass body, stove enamelled finish; with brass knob or lever handle and fixed, complete all as specified and directed.

Supply and fix for, drawer handles, projection drop (50mm to 65mm) on screwed plate, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix for, tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix for, harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete all as specified and directed.

Supply and fix for, ball catches with 8mm dia steel ball, and brass body and striking plate including letting in, complete all as specified and directed.

Supply and fix for, mortice lock, vertical type, size 100 mm 4 livers brass, complete all as specified and directed.

Supply and fix for, hydraulic hinges HYD-HG15SS15 degree of Prayag, complete all as specified and directed.

Supply and fix for, telescopic drawer slide TSC-SB20-ZNY soft close of Prayag, complete all as specified and directed.

Supply and fix for, mild steel flat iron 25 x 3mm as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed.

Supply and fix for, rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410 - W (Gde - E- 250) quality-A, complete all as specified and directed.

Supply and fix for, framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe 410 -W (Gde- E- 250) quality-A, complete all as specified and directed.

Supply and fix for, mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fix for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed.

Supply and fix for, rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Material and labour for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material and labour for, mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material and labour for, mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, factory made Steel ventilator with top hung shutter including hinges, steel peg stay, as per IS-1038:1983 (Amendment No.3 of May 2009), complete all as specified and directed.

Suupply and fix for, mild steel screw bolts (machine made), dia of neck 5 to 10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long, complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete as per TD drawing No. CESZ/2015/TD/005 dated 05 Jan 2015 and directed.

Supply and fix for, powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per TD drawing No. CESZ/2015/TD/005 dated 05 Jan 2015 and directed.

Supply and fix for, powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per TD drawing No. CESZ/2015/TD/005 dated 05 Jan 2015 and directed.

Supply and fix for, anodised aluminium powder coating of any colour (Minimum thickness of powder coating 50 micron) for window and ventilator shutters, fixed type/ sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. TD drawing No.CESZ/2015/TD/005 dated 05 Jan 2015, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mm x 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed.

Material and labour for, 0.9mm decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions and directed.

Material and labour for, 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including taking down old unserviceable board, complete all as specified and directed.

Material and labour for, 19mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work, complete all as specified and directed.

Material and labour for, 25mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base floor/ paving, complete all as specified and directed.

Material and labour for, 100mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base floor/ paving, complete all as specified and directed.

Material and labour for, 40mm thick plain cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor for receiving floor finish, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in bed finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in floor/ plinth protection/ paving/ bed, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.06 Sqm but not exc.0.11 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.18 Sqm but not exc.0.38 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), complete all as specified and directed.

All as per serial item No. 94 here-in-before but on skirting over and including 10mm thick backing coat in cement mortar (1:3).

Material and labour for, chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding in cement mortar (1:4), complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4), complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Material and labour for, machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, complete all as specified and directed.

Material and labour for, granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions on fair faces of brick work or concrete surfaces of manholes/ septic tank, finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of newly plastered wall surfaces and applying three coat of white wash, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer over 1mm thick wall putty, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed.

Supply and fix for, 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed

Supply and fix for, 4.0mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, 4mm thick sheet, ordinary quality, ground or obscured or frosted glass on one side and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed

Material and labour for, preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Cutting existing 40mm bore steel tubing for alterations or additions (Each cut measured), complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 25mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply and fix for 25mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply and fix for, 15mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix in repair for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix in repairs for, bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix for, bib tap, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix in repair for, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix for, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, stop valves, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repairs for, stop valves, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repairs for, stop valves, chromium plated, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix in repairs for, angle stop valves, chromium plated, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 25mm bore, complete all as specified and directed.

Supply and fix in repairs for, chromium plated, fancy type center hole mixer of standard quality for mixing hot and cold water all as per Cat No.BLQCP50071 of make Hindware or equivalent model of make as specified in PS, complete all as specified and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks double layers (cylindrical vertical with closed top) of 2000 litres capacity with ISI marked and all as specified in IS12701 including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified in SSR Part I and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701 including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed and taking down existing water tank, complete all as specified in SSR Part I and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 500 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball (Minimum weight - 210 gms), tank nipple screwed for iron pipe or brass ferrule, complete all as specified and directed.

Supply and fix for, soap dish all as per Cat No.AQN-7731 of make Jaquar or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix in repair for, toilet paper holder with flat recessed type stainless steel, complete all as specified and directed

Supply and fix in repair for, vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Supply and fix for, vitreous china squatting plate urinal, white (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and directed.

Supply and fix for, urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60gms), complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash down water closet pan (EWC) 'P' or 'S' trap (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repairs for, vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), connection to trap and to flushing cistern anti syphonage pipe including provision of PCC or lime concrete bedding and removal of debris complete all as specified and directed.

Supply and fix in repairs for, PVC valveless, syphonic action type, flushing cistern 10 litres capacity, low level, white, with inlet, ball valve, float and handle with flush pipe of polyethylene of low or high density or PVC 32mm dia including cutting & pinning in ends, making good the disturbed surfaces in cement mortar (1:3), complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash basin, white, flat back, size 550 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fix for, vitreous china wash basin, white, flat back, size 550 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, 32mm dia corrugated PVC waste pipe, chromium plated coupling 32mm dia and cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.

Supply and fix for, plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix in repair for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fix in repairs for, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fix in repair for, PVC bathroom cabinets quality as approved of size 600mm x 400mm with mirror on front door and one towel rail for hanging towel of MS chromium plated fixed with screw and wooden gutties etc. all as per Cat No.F680009CP of make Hindware or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix in repair for, sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Supply and fix in repairs for, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix in repairs for, brass chromium plated shower rose 125mm size with or without swivel joints with 225mm long arms, cast copper alloy chromium plated, fixing to 15mm steel pipe or union, complete all as specified and directed.

Supply and fix for, PVC (SWR) floor trap 75mm dia, plain with CP grating including jointing with solvent cement, complete all as specified and directed.

Supply and fix for, PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts, bolts etc., complete all as specified and directed.

Supply and fix for, 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts, bolts etc., complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) bends any radius, complete all as specified and directed.

Supply and fix for, 75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

Supply and fix in repair for, 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed.

Supply and fix for, 75mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Supply and fix for, 50mm bore UPVC low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq.cm including cutting, chasing, pinning and making good the floor as per existing, complete all as specified and directed.

Supply and fix in repair for, grating round 140 mm size of PTMT (Minimum weight 50gms), complete all as specified and directed.

Material and labour for, cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 100mm internal dia of pipe, complete all as specified and directed.

Material and labour for, cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required for 150mm internal dia of pipe, complete all as specified and directed.

Material and labour for, 150mm internal diameter salt glazed stoneware drain pipes laid in trenches and jointed, complete all as specified and directed.

Material and labour for, concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) for 150mm bore pipe, complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable 1100 volts grade, ISI 694 marked of size 1.5 Sqmm drawn in and including PVC rigid conduit (heavy duty, ISI marked) not less than 20mm dia with all necessary fittings such as bends, cross, elbow, tees etc. with MS pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting switches, sockets, fan regulator etc. and 3mm thick laminated sheet top cover (ISI marked) including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as continuous earth wire and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way switch, complete all as specified and directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 2.5 Sqmm 1100 volts grade, ISI 694 marked drawn in and including PVC rigid concealed conduit (heavy duty, ISI marked) not less than 20mm dia with all necessary fittings such as bends, cross, elbow, tees etc. with MS pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting socket outlet and 3mm thick laminated sheet top cover (ISI marked) including 2.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as continuous earth wire and connected to common earth dolly for for one socket outlet 3 pin 15/16 Amps on independent board, complete all as specified and directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 4.0 Sqmm 1100 volts grade, ISI 694 marked drawn in and including PVC rigid concealed conduit (medium heavy duty, ISI marked) not less than 20mm dia with all necessary fittings such as bends, cross, elbow, tees etc. with MS pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting socket outlet and 3mm thick laminated sheet top cover (ISI marked) including 4.0 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as continuous earth wire and connected to common earth dolly for for one socket outlet 5 pin 15/16 Amps on independent board, complete all as specified and directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one light/ ceiling fan/ exhaust fan controlled by one, one way switch, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 6 Amps on independent board, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 1.5 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 6 Amps on same board, complete all as specified and directed.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLS copper conductor cable of size 4.0 Sqmm in and including PVC rigid concealed conduit (heavy duty) of required dia with all necessary fittings including 4.0 Sqmm PVC insulated unsheathed stranded FRLS copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 15/16 Amps on independent board, complete all as specified and directed. Notes for item Nos 183 to 186 : Flush steel terminal box, inner plate and front plates shall be measured and paid sepertely under relevant item.

Supply and fix for, switch piano, flush type single pole, one way 6 Amp, 230 volts, complete all as specified and directed.

Supply and fix for, modular metal flush box 2 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 4 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 2 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 4 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 8 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, ceiling rose, surface bakelite, PVC/ polycarbonate 63.5mm x 23.5mm three terminals, complete all as specified and directed.

Supply and fix for, switch socket combination 2 in 1, 3/5 pin, 6 and 16 Amp flush type universal, complete all as specified and directed.

Supply and fix for, socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 4 way 200 Amps rated bus bar, double door type IP-43, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 way 200 Amps rated bus bar, double door type IP-43, complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply and fix for, single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole 20 Amps MCB, complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including PVC casing & capping medium duty (ISI marked) of required size with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of casing & capping shall be measured as one unit length.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including rigid PVC concealed conduit (medium duty) (ISI marked) of required size with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of rigid PVC conduit shall be measured as one unit length.

Supply and fix for, LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed. Make:- Havells cat No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent model of make as specified in PS.

Supply and fix for, LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. Make:- Havells cat No. ENDURALINEARNEOBS10WLED865SPCWH or equivalent model of make as specified in PS.

Supply and fix for LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fix for, round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fix for, LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete, complete all as specified and directed. Make:- Havells cat No. ENDCITYLITPLAT+SL35WLED75SASYBOPCWOSPD or equivalent model of make as specified in PS.

Supply and fix for, exhaust fan, steel body AC single phase 230V of size 300m sweep with, blades and frame and louvers, complete all as specified and directed.

Supply and fix for, electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.

Material and labour for, earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.50 metre below normal ground level connected to galvanised steel earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab (Reinforced with 8mm dia TMT bar @15cm centre to centre bothways and suitable handle made of 10mm dia), provision of funnel, wire mesh, 20mm bore galvanised steel tubing (medium grade) for watering, charcoal or coke and salt in alternate layers of 15cm (compacted thickness), 15mm bore galvanised steel tubing (light grade) for protection of earth lead connection, necessary excavation and earth work in any type of soil complete all as specified and indicated on electrical plate No.3 of SSR Part-I (2009) including testing on completion. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in the unit quoted rate).

Supply, laying, testing commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm, 4 core, complete all as specified and directed.

Supply, laying, testing commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm, 4 core, complete all as specified and directed.

Material and labour for, sand cushioning (dry) in trenches for protection of UG cables (below, above and around the UG cable laid in trenches) of 230mm spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and directed. (NOTE : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for).

Material and labour for, sub class 'B' brick, well burnt, old size, flat, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and directed.

Supply and fix for, GI tubing 20mm bore, light grade, laid in trenches for cable protection under the road/ path/ pole including taking down existing pipe, complete all as specified and directed.

Supply and fix for, GI tubing 25mm bore, light grade, laid in trenches for cable protection under the road/ path/ pole including taking down existing pipe, complete all as specified and directed.

Supply and fix for, GI tubing 40mm bore, light grade, laid in trenches for cable protection under the road/ path/ pole, complete all as specified and directed.

Provision of of RO plant (RO + UF + TDS) high purification capacity of 500 litres/ Hr alongwith chlorination dosing pump of capacity 0 to 5 LPH, chlorination dosing tank capacity 100 litres. Raw water feeding pump centrifugal type (make Kirloskar/ CRI), pressure dow flow graded sand filter with sufficient san, activated carbon filter with sufficient quantity activated carbon, antiscalent dosing system, antiscalent take of capacity 100 litres micron catridge filter working flow 1.0 Cum/ hr. High pressure pump vertical centrifugal type (make Kirloskar/ CRI), RO membarine elements model 4040 make Hydronotics/ Torey. Pressure vessels, fine polishing filtration system, UV disinfection system and oxone generator fully automatic operation with auto off facility including all fixing arrangement make Kent Elite or equivalenr as approved by GE, complete all as specified and directed.

M/S SAIKIA ENTERPRISE (BID ID -3221077)

NIHAR ENTERPRISE (BID ID -3221144)

M/S GOPAL ROY AND CO (BID ID -3214540)

PEE BEE INDIA (BID ID -3217541)