SPECIAL REPIARS TO BUILDING NO P13 QTR NO 1 TO 4 AT NEW FORT GLACIS NFG UNDER GE CHENNAI

Amount

B/R PORTION:

Demolition of reinforced cement concrete of any description in roofs, floors, (other than ground floors) beams, stair cases, landing chajjas and similar suspended works including separating reinforcement and removing rubbish from site and depositing whrere directed by Engineer-in-Charge complete all as specified.

M&L for reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregaate as in slab for cooking platform complete all as specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for reinforced design mix M-30 grade concrete using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all a specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for reinforced design mix M-30 grade concrete using 20 mm graded stone aggregate as in Chajjas complete all as specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for reinforced design mix M-30 grade concrete using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.Note: Reinforcement shall be measured and paid separately under relevant item.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc ,rough finished surfaces of concrete flat complete all as specified.

M&L for formwork to soffits of suspended slabs such as roof slab floor slab not exceeding 200mm thickness ,fair finished surface of concrete complete all as specified and as directed

M&L for form work to chullah hoods, chajja's, trough and similar item including edges ,rough finished flat surfaces of concrete complete all as specified.

M&L for form work to edges of concrete flat, treads, breaks in floors, window cills, concrete railings, openings in concrere walls, floors and roofs not exceedings 20cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10cm but not exc 20cm wide,rough finished surface of concrete complete all as specified.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified

M&L for Mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified

M&L for Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified

M&L for rendering 10 mm thick in cement mortar 1:3 mixed with water proofing compound PIDI PROOF LW at the rate of 200ml per bag of cement and finished even and smooth without extra cement complete all as specified. Note : Liquid Water Proofing Compound shall be measured and paid separately under relevant item.

M&L for cleaning and preparation of newly plasteres roof surfaces and applying the water proofing treatment as under. (a) Applying first course of bituminious (oil based) primer confirming to IS-3384 @ 0.4 litres /sqm over the screed bed. (b) Applying second course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C and applied @ 1.2 kg/sqm. (c) Applying third course of APP (Atactic polypropylene) based polymeric membrane minimum weighing 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 100 mm overlap by forced / torch application as per Manufactures instructions. (d) Applying fourth course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 degree C and applied @ 1.2 kg/sqm over APP membrane, (e) Applying fiveth and final course of one coat of solar reflective aluminium paint @ 0.10 Litre/Sqm on roof surfaces complete all as specified and directed. Note: Water proofing treatment shall be executed through authorised applicator of original Manufacturer

Taking down cement plaster on brick work or stone walls etc including racking out of joint , hacking for key scrubbing down with water etc.complete all as specified.

M&L for rendering 15 mm thick on fair faces of brick work in two layers, first layer 10 mm thick in cement mortar 1:6 and second finishing coat 5 mm thick in cement mortar 1:4 mixed with water proofing compound as per Manufacturers instructions and finished even and smooth on external surfaces complete all as specified. Note : WPC shall be measured and paid separately .

M&L for rendering 5mm thick in cement mortar 1:3 on fair faces of ceiling surfaces and finished even and smooth without using extra cement complete all as specified

M&L for rendering 10mm thick in cement mortar 1: 6 on fair faces of brick work / concrete surfaces finished even and smooth without using extra cement complete all as specified.

Supply only Iiquid waterproofing compound

M&L for applying three coats of white wash in ceiling including preparation of newly plastered surfaces complete as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of alkali-resistant priming paint on new plastered wall surfaces over and including applying 2 mm thick plaster of paris putty on new plastered surfaces of wall complete all as specified.

M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gms / litre and UV resistance as per IS15489:2004., alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot tinted) with silicon additives @ 1.43 litre/ 10sqm over and including priming coat of exterior primer applied @ 0.90litre/10sqm over new surface complete all as specified.

Demolition of brick masonry built in cement mortar of any description including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work including removal of rubbish complete.

M&L for brickwork with fly ash bricks , straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified

M&L for anti termite treatment to soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match with the existing floors complete all as specified

M&L for PCC 1:2:4 type B0 using 20 mm graded aggregate ,25mm thick as in sub base floor complete all as specified

M&L for Vitrified light shade ceramic tiles 10mm thick (square / Rectangle) polished, area of each tiles n.exc.0.36sqm in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified.

M&L for Vitrified light shade ceramic tiles 10mm thick (square / Rectangle) polished, area of each tiles n.exc.0.36sqm on vertical surfaces such as skirting, dados and risers to step etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified.

M&L for non -skid coloured ceramic joint free tiles 7 mm to 8 mm (Square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified.

M&L for non -skid coloured ceramic joint free tiles 7 mm to 8 mm (Square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces such as skirting, dados and risers to step etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified.

M&L for non -skid coloured ceramic joint free tiles 7 mm to 8 mm (Square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified.

M&L for glazed coloured ceramic joint free tiles of size 350mmx250mmx7mm thick / 450mmx350mmx7mm thick on vertical surfaces such as skirting, dados and risers to step etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile , over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone including grinding and polishing of approved quality of any size set and jointed in grey cement slurry laid over and including 15 mm thick screed bed in CM (1:4) including polishing the granite stone by using mechanical grinder and moulding edges compete all as specified and as directed.

M&L for rounding to edges of stone slabs, such as in steps, cooking platform, and other similar situations.

M&L for mirror polishing machine cut kota stone slab flooring 20mm to 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified

M&L for mirror polishing Kota stone slab 20mm to 25mm thick as in riser of steps, skirting, dado and pillar etc laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 10mm thick backing coat in cement mortar 1:3 complete all as specified

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area not exc.1.5 sqm each including separating guard bars/grills/wire mesh etc., all as specified and as directed

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area exc.1.5 sqm but not exc 4sqm each including separating guard bars/grills/wire mesh etc., all as specified and as directed

Taking down shutters of any description exc. 1sqm but not exc. 2 sqm each including builders hardware complete all as specified and directed

Taking down shutters of any description exc. 1sqm but not exc. 2 sqm and refixing in the same opening complete all as specified and directed

Dismantling unframed timber scantlings 40 sq.cm and over in section, in any position for hand rail etc complete all as specified

S&F first class hardwood (Teak) as in handrails of size 100mmx75mm rounded or shaped with splayed faces in straight lengths and fixed in position complete all as specified and directed.

S&F second class hard wood as in plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified

S&F 35mm thick second class hard wood plain, framed pannelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneer on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified

S&F second class hard wood 35 mm thick glazed and skeleton door shutter , open rebated and prepared to receive glass, gauge etc, (with sash bars) edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass etc, size of members of shutter as specified in SSR Part I, Section 8, clause 8.2 (a) Supplied and fitted to chowkats complete all as specified

S&F 40 mm thick flush shutter solid core construction with block board core and plywood face panel , commercial type on both sides complete all as specified

M&L for applying two coats of synthetic enamel paint on wooden surfaces including necessary preparation of new wooden surfaces of any description exc. 10cm in width or girth complete all as specified and directed.

S&F Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.4mm fixed with aluminium wire staples fixed to wood/steel frames fixed all as specified and as directed

Dismantling boarding of any description, fixed in any position with nails complete all as specified

S&F in repairs aAluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.4mm fixed with aluminium wire staples fixed to wood/steel frames complete all as specified and as directed

M&L for cutting holes in brick walls built in cement mortar for inserting hold fast etc depth of embedded portion of hold fasts exc half brick but n exc one brick thick wall and making good to the dismantled portion in cement mortar 1:3 or providing cement concrete 1:2:4 type B1complete all as specified and directed

M&L for preparing surfaces of wood and wood based material, treating ends of posts, backs of chowkats, etc.with bituminous black paint , area tarred exc 0.1 sq.m but n.exc 0.5 sqm each complete all as specified.

M&L for preparing surfaces of steel surfaces, treating small articles such as stop, covers, gully gratings, holdfasts, end of posts, backs of chowkats, etc with bituminous black paint , area n. exc 0.1 sqm each. Complete all as specified.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge metred cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mm x 15mm MS square tube inside the 19mm x 19mm square tube fixed to wall in repairs by drilling 100mm long MS screws using PVC fastener all as per specification and directed.

S&F Factory made solid PVC molded door shutter with wood free EPS 28 to 30mm thick with 2,4,6 raised panel design with 2mm thick moulded Prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing and all as directed.

S&F mild steel butt hinges of 100mm size medium weight cold rolled

S&F aluminium anodised barrel tower bolts, extruded section of size 200mm long

S&F aluminium handles cast type anodised 150 mm size.

S&F aluminium alloy, anodised sliding door bolts 300mm long with hasp and stable (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified and as directed.

S & F mild steel 300 mm , ordinary rat rail rod pattern springs including rollar and rollar plate complete.

S&F Floor door stopper of aluminium alloy body & tongue, anodised, with hard drawn steel spring.

S&F in repairs cast Aluminium (Die cast ) body door closer hydraulically regulated, designation No.2 univrsal type, suitable for door shutters up to 701mm to 850 mm in width and of weight between 36 to 60 kg complete all as specified.

S&F in repairs mortice lock vertical type mild steel size 100 mm 4 leavers with stain less steel handle set suitable for right or left, inside or out side opening doors,complete all as specified.

S&F in repais 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative chioce lamination and other side balancing white lamination fixed with screws to timber frame work complete all as specified

S&F 6mm thick external teak wood lipping over particle board fixed with nails complete all as specified

S&F in repairs contineous (piano) hinges mild steel, bright finish or electro galvanised width of flaps (when open) 30mm complete all as specified.

S&F Brass locks for drawer, cupboard shutters grade I, of size 75 mm s (2 levers) complete all as specified

S&F 40 mm brass dia cuboard knobs fixed with nuts ,screws and washers of mild steel, bright finished

S&F In repair Hasp and staple of size 125mm, alluminium anodised wire type stove enemalled black including bolt to hinges plate and fixed with screws all as specified.

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook & pintel hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way & three way straps,plate washers & similar small articles conforming to Fe290-0 Gde E-165.

M&L for dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work confirming to Fe 290 Gde-E-165 complete all as specified

S&F aluminium powder coated sliding window using alumimium section weighing not less than 0.495 Kg per RM for frame and 0.48 Kg per RM for sliding shutters including fixed with aluminium anodised snap beads, screws and fixed alongwith same section in three rolling sliding shutters, two for fully glazed with 5mm thick tinted glass fixed with glazing clips, and third one for aluminium wiremesh shutters etc complete all as specifed and directed. Note: The quoted rate shall be inclusive for all builders hard ware , tinted glass,wire mesh ,locking arrangements and other accessories as required at site.

S&F aluminium powder coated ventilators using alumimium section weighing not less than 0.48 Kg per RM for frame louvers including sliding shutters including fixed with aluminium anodised snap beads, screws and fixed alongwith same section in two rolling sliding shutters ,one for fully glazed with 5mm thick tinted glass fixed with glazing clips, and other one for aluminium wiremesh shutters etc complete all as specifed and directed. Note: The quoted rate shall be inclusive for all builders hard ware , tinted glass,wire mesh ,locking arrangements and other accessories as required at site.

S&F repairs aluminium designer curtain rods (Draw berms rod) exterior grade 3 mm thick with holding clambs and fixed to wall PVC rawel plug and brass screws all as specified and as diredcted

S&F Aluminium designer curtain rod brackets suitable for designer cutain rod as specifed here in above .

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness ,below or above ground level complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone coarse agregate as in plinth protection,finished even and smooth without using extra cement complete all as specified.

M&L for complete removal of existing treatment, washing, rubbing down and stopping of distempered surfaces and applying two coats of distemper oil emulsion over a coat of alkali-resistant priming paint over and Including applying plaster of paris putty of 2mm thick on old plastered surface of wall complete all as specified.

M&L for applying one coat of white wash as in ceiling including preparation of old decorated surface of ceiling complete all as specified

M&L for applying three coats of white wash on new wall surface including preparation of surface complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old wooden surface of any description exc. 10cm in width or girth including preparation of surface complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description exc 10cm in width or girth including preparation complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old steel surface of any description exc 10cm in width or girth including preparation complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F in repairs PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F in repairs PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints fixed in floors or trenches complete all as specified.

S&F in repairs PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed in floors or trenches complete all as specified.

S&F in repairs PVC (SWR) bend any radius with access door suitable for 110mm dia pipes.

S&F in repairs PVC (SWR) bend any radius with access door suitable for 75mm dia pipes.

S&F in repairs PVC (SWR) Vent cowl suitable for 110mm dia vent pipe.

S&F in repairs PVC SWR branch piece single 'Y' equal or unequal 110mm bore with access door.

S&F in repairs PVC SWR branch piece single 'Y' equal or unequal 75mm bore with access door.

Taking up or down old steel tubing of 15mm dia with connections including cleaning for refixing or removal to store complete all as specified.

Taking up or down old steel tubing of 20mm dia with connections including cleaning for refixing or removal to store complete all as specified.

S&F CPVC Pipes 16mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceilings or laying in floors complete all as specified complete.

S&F CPVC Pipes 20mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceilings or laying in floors complete all as specified complete.

Supply, hoisting and fixing in position of 500 litre capacity two layered Rotational Molded Polyethylene water storage tank (cylindrical vertical with closed top) complete all as specified in SSR Part- I including dismantling the existing PVC OHT

Supply, hoisting and fixing in position of 1000 litre capacity two layered Rotational Molded Polyethylene water storage tank (cylindrical vertical with closed top) complete all as specified in SSR Part- I including dismantling the existing PVC OHT

S&F in repairs ball brass valve for 20mm bore pipe high pressure with polyethylene float and fly nut complete screwed for iron pipe complete all as specified

S&F in repairs Gun metal globe or gate valve with iron wheel head screwd both ends for iron pipe and fixed for 20 mm dia complete all as specified

S&F in repairs 15mm dia pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified

S&F in repairs 15mm dia bib taps, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified

S&F in repairs PVC connection of 15mm dia 450mm long of superior quality all as specified.

S&F in repairs brass chromium plated shower rose of size 75mm with swivel joints including shower arm 15mm size, 195mm long with bend of 45 degree with flange for fixing with 15mm dia pipe completed all as specified and as directed

S&F in repairs brass chromium plated stainless steel towel rail, 20 mm dia 'D' type, 60 mm long between flanges

S&F in repairs grating round 140mm size of PTMT (Minimum weight 50gms) complete all as specified

S&F in repairs vitreous china Wash Hand Basin, white, flate back of size 550x400mm excluding taps, waste, chain and plug and porcelain stopper out including brackets completed all as specified and as directed

S&F in repair vitreous china wash down water closet, white, squatting pan Orissa pattern of size 580x440mm with integral foot rest including making necessary connections to soil pipes and flushing cistern completed all as specified and as directed

S&F in repairs vitreous china wash down water closet (pedestal pattern ) white (excluding fixing bolts flushing cistern and flush pipe ) including making necessary connections to soil pipes and flushing cistern completed all as specified and as directed

S&F in repairs PVC low level flushing cistern 10 litres capacity with complete accessories, PVC flush pipe, PVC over flow pipe etc., and connected to water closet completed all as specified and as directed

S&F plastic water closet seat cover, black or white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device.

S&F In repair towel ring PTMT of fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 90 Gms)

S&F in repairs stainless steel sink over all size of 915mmx460 mm and bowl size with draining board of 410mmx330mmx160mm, made out of 1mm thick stainless steel sheet of good quality including proven of waste coupling and 40mm dia waste pipe fitted over a pair of CI brackets all as specified and as directed .

S&F in repairs health faucet (Hand shower) with 1metre flexible tube with wall hook, Chromium Plated Make : Prayag Cat NoBEA-97

S&F toilet paper holder with flap recessed type matt chromium plated Make : Prayag cat No.BA-38

S&F PVC waste pipe for wash hand basin (size 31/32mm x 900mm length) Make : Prayag Cat No.327

S&F in PVC waste pipe for Sink waste pipe of 38mm/40mm dia , 1150mm length Make : Prayag Cat No.330

S&F in repair brass chromium plated 15mm wall mixer valve ( 2-in-1) with L Bend complete all as specified and diected Make : Prayag Cat No.8375

S&F In repair15mm dia angle cock with flange, chromium plated complete all as specified Make : Prayag Cat No.8310

S&F in repair 15mm dia Sink cock with flange, chromium plated Make : Prayag cat No 8716

S&F in repair Tumbler holder with glass Make : Prayag Cat No.BA-26N

S&F In repair 32mm brass full thread SS waste coupling for wash hand basin Make : Prayag Cat No.BE-11

S&F in repair CP brass waste coupling 40mm full thread for kitchen sink Make : Prayag Cat No BEA-16B

S&F in repair soap dish ,matt finished chromium lated (MCH/Colour) Make : Prayag Cat No.BA-05G

S&F in repair corner glass shelf superior quality matt finished chromium plated (MCH/Colour CP ) with bracket and fittings Make : Prayag cat No BEA-44

S&F in repair glass shelf matt finished chromium plated (MCH/Colour CP) of size 600mm long with bracket and fittings Make : Prayag Cat No.BEA-45

S&F In repair CP towel rack 600mm long with lower hanger stainless steel Make : Prayag cat No.BA-12

S&F in repair 15mm dia bib cock long body with flange, chromium plated Make : Prayag cat No-8308

S&F in repairs Stailness steel plate rack of size (36'' x 36 " 10") with separators and 3 tier shelves, provision of hook 9 Nos made out of stailness steel sheet of grade AI SI 304 complete all as specified . Make: Prayag CAT No 350

S&F in repair 15mm dia 2 way angle cock with flange, chromium plated Make : Prayag cat No.8311

S&F in repair CP square trap (101mmx101mm) with waste hole Make : Prayag cat No.FT-73

S&F in repair PVC cabinet mirror PTMTof size 400mm x 500mm with sided shelves fancy type of superior quality complete all as specified and as directed . Make : Prayag cat No.554

S&F in repair 15mm dia CP bib cock nozzle with flange(washing machine tap) Make : Prayag cat No.8305

Removing the building materials of any description obtained from demolition (other than soil obtained from excavated) to outside of MoD land completely all as directed by Engineer in charge at site.

INTERNAL ELECTRIFICATION

Taking down carefully copper / aluminium point wiring light, fan, socket or power complete with fittings such as switches, ceiling roses,regulators sockets etc and making good disturbed surfaces of walls, floors to match with the existing surface complete all as specified

M&L for point wiring of size 1.5 sqmm with PVC insulated unsheathed multistranded copper conductor cabel of 1100V grade drawn through new non metallic rigid PVC conduit including accessories,including cutting/chasing concealed in wall/floor and fixed on ceiling/roof etc, including pressed steel terminal boxes concealed in walls for housing modular switchs,sockets, fan regulators etc., incl provn of 1.5 sqmm PVC insulated copper earth conductor cable for earth continuity and connecting to common earth dolly complete for complete for :-

one light point controlled by one switch

one fan point controlled by one switch

one 3 pin socket outlet 5 amps on the same board controlled by one switch.

one 3 pin socket outlet 5 amps on independent board controlled by one switch.

one bell/buzzer point controlled by one bell push

As per above items No 141 for one socket outlet three pin 15 Amps controled by one switch independent board with 2.5 sqmm size cable

As per above item No. 141 for one 3 pin socket outlet. 15 Amps, independent, with 4 sqmm cables ( for Geyser )

M&L for point wiring of size 1.5 sqmm (two run) with PVC insulated unsheathed multistranded copper conductor cabel of 1100V grade drawn through non metallic rigid existing PVC conduit , in wall/floor and fixed on ceiling/roof etc, including pressed steel terminal boxes concealed in walls for housing mocular switchs,sockets, fan regulators etc., incl provn of 1.5 sqmm PVC insulated copper earth conductor cable for earth continuity and connecting to common earth dolly complete for :-

one light point controlled by one switch

one fan point controlled by one switch

one 3 pin socket outlet 5 amps on the same board controlled by one switch.

one 3 pin socket outlet 5 amps on independent board controlled by one switch.

As per above items No 149 for one socket outlet three pin 15 amps control by one switch independent board with 2.5 sqmm size cable

S& F for modular cover plate with frame 3 module

S& F for modular cover plate with frame 4 module

S& F for modular cover plate with frame 6 module

S&F modular switches suitable for type AC 240V, 6 amps 1 module

S&F modular sockets suitable for type AC 240V, 6 amps 2 module

S&F modular switches suitable for type AC 240V, 16 amps 1 module

S&F modular power sockets suitable for type AC 240V, 16 amps 2 module

S&F modular fan regulator suitable for type AC 240V, 2 module

S&F modular bell switch suitable for type AC 240V, 16 amps

S&F call bell of multi music type A/C 230 volts

S&F ceiling rose , polycarbonate, isolated body with 2 to 3 terminals

Taking down ceiling fan and exhaust fans of any size and any description including connected accessories and deposited in AGE E/M store complete all as specified and directed.

S&F ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep five star rated with brushless direct current motor (BLDC) complete all as specified and directed

S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed

Taking down the existing geyser, refixing the same after all necessary plumbing and electric works done and make necessary repairs if any, complete all as specified and as directed

S&F 20 Watts LED COOL LIGHT fitting, surface mounting general purpose LED Battens in Extruded Aluminum housing with wide range of wattages to suite variety of application areas, complete all as specified . Make : Havells Cat No. LUMILINEPLUSNEOBS20WLED865SPCSSIND or other equivalent cat part in Philips/Bajaj.

S&F 10 Watts LED COOL LIGHT fitting, surface mounting general purpose LED Battens in Extruded Aluminum housing with wide range of wattages to suite variety of application areas, complete all as specified and directed . Make : Havells Cat No. LUMILINEPLUSBS10WLED865SPCSSIND other equivalent cat part in Philips/Bajaj.

S&F 15 Watts round ceiling COOL LIGHT is a functional range of aesthetically designed surface mounted downlights with aluminum housing and heat sink for better thermal performances, complete all as specified and as directed Make :Havells Cat No. INTEGRANXTRDDLRSURD15WLED865S other equivalent cat part in Philips/Bajaj.

S&F 10 Watts COOL LIGHT environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head back-lit LED luminaire comprising of high brightness LEDs, complete all as specified and as directed Make: Havells Cat No. HEXAFT10WLED857SSYMBOPC other equivalent cat part in Philips/Bajaj.

Taking down the existing AC box of any type and any size complete by disconneting the electric supply properly and making good surface complete all as specifided and directed

S&F MCB Power unit with 4 module steel box consisting of 3 pin 24 Amps socket with Plug top and MCB SP 25 Amps, suitable for operation of AC & Geysers etc. complete all as specified .Make :- Havells/Legrand/Anchor

Taking down sub main wiring of any type and any size completely by disconneting the electric supply properly and making good surface all as specifided and directed

S&F sub main wiring complete with two runs of 10 sqmm PVC insulated unsheathed single core multistrand copper conductor cable of 1100 volts grade drawn through new non metalic rigid PVC conduit pipe concealed in wall alongwith accessories fixed on walls/floors/ceiling with one run of 10 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor all as specified and directed . Note:- Two runs of PVC insulated cable 10 sqmm ,one run 10 sqmm of earth wire and one run of conduit with accessories shall be measured as one unit length.

Taking down MCB DB of any type and any size completely by disconneting the electric supply properly and making good surface all as specifided and directed

S&F MCB distribution board made of CRCA sheet, powder coated paint comforming of IS 13032, double door fixed in switch boards/wall at various places of capacity 415 volt 8 way MCB DB, TPN with 200 Amp rated bus bar conform to IP 38 protection complete all as specified

S&F MCB distribution board made of CRCA sheet, powder coated paint comforming of IS 13032, double door fixed in switch boards/wall at various places of capacity 415 volt 12 way MCB DB, SPN with 200 Amp rated bus bar conform to IP 38 protection complete all as specified

Taking down MCCB/MCB any type and any size completely by disconneting the electric supply properly and making good surface all as specifided and directed

S&F in repairs MCCB adjustable thermal & magnetic setting 415V, 4 pole, 50Hz of cap 160 Amps 36 KA complete all as specified

S&F MCB SPN 40-63 Amps 415 Volts complete all as specified

S&F MCB of Single pole of rating 6 to 32 Amps 240 Volts complete all as specified

M&L for Earthing complete with galvanised steel earth plate electrode 60cm x 60 cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m deep below ground level with top edge of plate not less than 1.5 below ground level connected to GI 4 mm earth wire by means of bolts, nuts check nuts washers made of galvanised iron or steel earth wire protected by GI pipe 15 mm bore light grade connected upto switch board incl 20mm bore GI water pipe with funnel and wire mesh all as shown in electrical plate No.3 of SSR Part I including dearth chamber of PCC 1:2:4 type B1 using 20mm grade aggregate with RCC cover slab 1:2:4 type B1, 40mm thick with 15mm dia MS bar 100mm C/C both ways and 6 MM dia MS hooks complete all as specified inlcuding testing on completion.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft / loose soil for laying cables / pipes / erection of poles etc all as specified and as directed.

Returning filling in soil including spreading leveling watering well ramming in layers not exceeding 25 cm each all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and as directed.

M&L for fine seived excavated dry soil laid to the required width of trench at botom and top of cable as cushioning to cable complete all as specified . Note :- Thickness shall be measured after punning

Supply and laying burnt bricks, old size, sub class 'B', laid flat adjacent to each other, perpendicular to cable with width equal to length in trenches for protection of cable all as specified and as directed.

Supply and lay GI tube light grade 40mm bore with all fittings laid in trenches/ floor as in road crossing etc., complete all as specified and as directed. Note: Excavation and earth work as required shall be measured and paid separately.

Supply and lay XLPE insulated, screened, PVC bedded, galvanised strip or wire armoured, heavy duty LT,UG cable with aluminium conductor, 1100 volts grade of cross sectional area 50 Sqmm 3.5 core in trenches,under road/ floors/ along poles or fixed on wall etc. including connecting up using suitable size aluminium lugs testing and commissioning complete all as specified and directed.

M&L for cutting existing GI water tubing inposition for insertion of Tee of 80 x 80 x 40 mm size for bore of pipe GI 80 mm including excavation complete all as specified and directed

Supply and lay galvanised steel water tubing 40mm bore medium grade with all fittings such as bends, tees, unions, elbows, connecting pieces, plugs, sockets etc., laid in trenches complete all as specified and directed.

Supply and lay galvanised steel water tubing 25mm bore medium grade with all fittings such as bends, tees, unions, elbows, connecting pieces, plugs, sockets etc., laid in trenches complete all as specified and directed.

S&F 25mm boreGun metal globe / Gate valve conforming to IS 778-1984 with iron wheel head, screwed both ends for GI pipe including all fittings/ fixutres like nipple, union etc, complete all as specified and directed.

S&F 40mm boreGun metal globe / Gate valve conforming to IS 778-1984 with iron wheel head, screwed both ends for GI pipe including all fittings/ fixutres like nipple, union etc, complete all as specified and directed.

Taking out unserviceable CI/GI/PPR/UPVC/DI/HDPE water main from trenches/walls/ floors including fittings / fixtures like bend, Tee, Union, Elbow etc with socketted ends and lead joints including burning out joints and all as specified and as directed by Engineer-in-Charge. Note: Excavation and earthwork shall be measured and paid separately under relevant items.

25mm bore GI pipe

40mm bore GI pipe

YOGAA MANPOWER AGENCY (BID ID -3354015)

KS CONSTRUCTIONS (BID ID -3357654)

DJ Group (BID ID -3365287)