Smart Distribution Project and Undergrounding of Electrical Infrastructure Work under RDSS

Undergrounding of HT/LT line at important tourist places-Conversion of 33 KV OH to UG Line as per TS & Approved Drawings.

Supply of 33 KV XLPE Insulated armoured Al. Cable of size 3x300 mm2.

Digging of trench for laying of Double circuit 33KV 3x300 sq.mm XLPE cable and making of trench for two nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 33 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Digging of trench for laying of Single circuit 33KV 3x300 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 33 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x300 Sq. mm 33 KV XLPE Insulated armoured Al. Cable underground in cable trenches and earth filling of trenches

Laying of 33 KV 3x300 Sqmm. XLPE Cable underground through HDPE Pipe at 1050 mm below the ground surface.(by HDD method) for road crossing including providing and fixing cable route marker.

Hoisting of cable on double pole with the help of cable clamp with N&B of suitable size

Supply & Erection of of Heat Shrinkable Termination Kit Outdoor for 33 KV 3x300 sq. mm XLPE Cable

Supply & Erection of of Heat Shrinkable Straight Through Jointing for 33 KV 3x300 sq. mm XLPE Cable

Supply & Erection of 160 mm dia. HDPE pipe. (PE80 PN 6 as per IS:4984/2016 )

Supply & Erection of G.I. pipe 150mm with clamp and nut & bolts (Medium Duty Class B)

Supply & Erection of 11 Mtr. long Steel Tubulor Pole SP-55 with Base Plate. (410 SP 55)

Excavation & Concreting of supports with Grounting f 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 11 mtr STP Pole of depth 1.8 meter with 300 mm Muffing.As per TS.

Supply & Erection of Galvanised Angle Iron 65x65x6mm, Galvanised Channel 125x65mm, Galvanised Channel Iron 100x50x6mm as per TS & approved drawings.

Supply & Erection of 33 KV MS Number Plate (250x200mm) with Clamp and Nuts & Bolts.

Supply & Erection of 33 KV MS Danger Board(250x200 mm) with Clamp and Nuts & Bolts.

Supply & Erection of G.I. Barbed Wire.

Supply & Erection of 33kv Polymer Pin Insulator (10 KN).with N&B

Supply & Erection of Galvanised earthing rod of 20x2500 mm(GI solid Rod) etc. together with fixing arrangement as per TS.

Supply & Erection of 300 sq.mm Alu. Lug .

Supply & Erection of Single core PVC cable 300sqmm for jumpering .

Supply & Painting of Alluminium paint .

Supply & Painting of Red Oxide paints.

Supply & Erection GI new Pre Fabrication Clamp made of 50*6 mm GI strip with nut & bolts .

Supply & Erection of 33 KV Galvanized Stay Complete (GI Stay Rod 20x1800 mm Turn Buckle,Anchor Plate As per TS

Stay Set Grouting 0.3 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips (1:2:4) as per approved drawings, scope of works and TS.

Supply & Erection of GI Stay wire 7/8 .

Supply & Erection of Guy Insulator.

Supply & Erection of cable warning tape.

Supply & Erection of cable route marker .

Supply & Erection of 33 KV LA ( 3 nos =1sets) .

Supply & Erection of GI wire 6 SWG.

Dismantling of Old Existing line and carriage of dismentalled Pole/Conductor/all other material upto utility Store as per site condition.

Supplying of 33 kV, 3CX 400 Sq.mm, XLPE, armoured Cable Undergrounding work by using Horizontal Directional Drilling & Open Trench Technique

Supply of 33 KV XLPE Insulated armoured Al. Cable of size 3x400 mm2.

Digging of trench for laying of Single circuit 33KV 3x400 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 33 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x400 Sq. mm 33 KV XLPE Insulated armoured Al. Cable underground in cable trenches and earth filling of trenches

Laying of 33 KV 3x300 Sqmm. XLPE Cable underground through HDPE Pipe at 1050 mm below the ground surface.(by HDD method) for road crossing including providing and fixing cable route marker.

Supply & Erection of of Heat Shrinkable Termination Kit Outdoor for 33 KV 3x400 sq. mm XLPE Cable

Supply & Erectio of of Heat Shrinkable Straight Through Jointing for 33 KV 3x400 sq. mm XLPE Cable

Supply & Erection of 200 mm dia. HDPE pipe. (PE80 PN 6 as per IS:4984/2016 )

Supply & Erection of cable route marker .

Supplying and laying of 11 kV, 3CX 300 Sq.mm, XLPE, armoured Cable Undergrounding work by using Horizontal Directional Drilling & Open Trench Technique

Supply of 11 KV XLPE Insulated armoured Al. Cable of size 3x300 mm2.

Digging of trench for laying of Single circuit 11KV 3x300 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 11 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x400 Sq. mm 11 KV XLPE insulated cable underground in cable trenches and earth filling of trenches.

Laying of 11 KV 3x300 Sqmm. XLPE Cable underground through HDPE Pipe at 1050 mm below the ground surface.(by HDD method) for road crossing including providing and fixing cable route marker.

Supply & Erection of 160 mm dia. HDPE pipe. (PE80 PN 6 as per IS:4984/2016 ).

Supply & Erection of of Heat Shrinkable Termination Kit Outdoor for 11 KV 3x300 sq. mm XLPE Cable.

Supply & Erection of of Heat Shrinkable Straight Through Jointing for 11 KV 3x400 sq. mm XLPE Cable.

Supply & Erection of cable route marker .

Optic Fibre Cable

Supply & Laying of Optic fibre cable (single mode 8 core)

Supply & Laying of Optic fibre cable (single mode 24 core)

Supply & Laying of 35mm dia HDPE Pipe for Cable laying

Supply & Laying,of Splicing, OTDR

Supply & Erection of Partial Discharge monitoring equipment/ sensors for U/G cable

Conversion of 11 KV Line O/H to UG as per TS & Approved Drawings.

Supply of 11 kV XLPE insulated armoured Al. cable of size 3Cx185 sq.mm

Digging of trench for laying of double circuit 11KV 3x185 sq.mm XLPE cable and making of trench for two nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 11 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Digging of trench for laying of Single circuit 11KV 3x185 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 11 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x185 Sq. mm 11 KV XLPE insulated armoured Al. underground in cable trenches and earth filling of trenches

Supply & laying of 110 mm dia. HDPE pipe by Horizontal drilling by HDD method as per site condition, (PE80 PN 6 as per IS:4984/2016 )

Laying of 11 KV 3Cx185 sq.mm XLPE Cable underground through HDPE (by HDD method) including providing and fixing cable route marker.

Hoisting of cable on double pole with the help of cable clamp with N&B of suitable size .

Supply & Erection of Heat Shrinkable Termination Kit Outdoor for 11 KV 3x185 sq. mm XLPE Cable .

Supply & Erection of Heat Shrinkable Straight through Jointing Kit for 11 KV 3x185 sq. mm XLPE Cable

Supply & Erection of G.I. pipe 100 mm dia with clamps, Nut and Bolts.(Medium Duty Class B)

Supply & Erection of 11 Mtr. long. Steel Tubular Poles.SP-55with Base plate.(410 SP 55)

Excavation & Concreting of supports with Grounting f 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 11 mtr STP Pole of depth 1.8 meter with 300 mm Muffing.As per TS.

Supply & Erection of Galvanised Angle 65x65x6 mm,.Galvanised channel 100x50x6 mm, Galvanised Angle 50x50x6 mm.

Supply Erection of 11 KV MS Number Plate (250x200)with Clamp and Nuts & Bolts.

Supply & Erection of 11 KV MS Danger Board (250x200mm) with Clamps and Bolts.

Supply & Erection of G.I. Barbed wire.

Supply & Erection of 11 kv Polymer Pin Insulator (5KN), pin with N&B) .

Supply & Erection of GI earthing rod of 20x2500 mm (GI solid Rod). wire etc.

Supply & Erection of GI wire 6 SWG .

Supply & Erection of Aluminum lugs -185 Sq.mm.

Supply & Erection of Single core PVC cable 185sqmm for jumpering .

Supply & Erection of Alluminium paint.

Supply & Erection of Red Oxide paints .

Supply & Erection of Fabrication clamp made of 50*6 mm GI strip with nut & bolts.

Supply & Erection of 11 KV Galvanized Stay Complete (GI Stay Rod 16x1800 mm, Anchor Plate.

Stay Set Grouting 0.3 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips (1:2:4) as per approved drawings, scope of works and TS.

Supply & Erection of GI Stay wire 7/10.

Supply & Erection of Guy Insulator .

Supply & Erection of cable warning tape .

Supply & Erection of cable route marker .

Dismantling of Old Existing line and carriage of dismentalled Pole/Conductor/all other material upto utility Store as per site condition.

Installation of New DT as per TS & Approved Drawings.

Supply & Erection of 11 Meter long Steel Tubular Pole SP -55.(410 SP 55) .

Excavation & Concreting of supports with Grounting f 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 11 mtr STP Pole of depth 1.8 meter with 300 mm Muffing.As per TS.

Supply of 11 kV XLPE insulated armoured Al. cable of size 3Cx185 sq.mm .

Digging of trench for laying of Single circuit 11KV 3x185 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone slab after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x185 Sq. mm 11 KV XLPE insulated cable underground in cable trenches and Back filling of trenches .

Erection of Hoisting /Raising of cable on double pole with the help of cable clamp with N&B of suitable size .

Supply & Erection of Heat Shrinkable Termination Ki Outdoor for 11 KV 3x185 sq. mm XLPE Cable .

Supply & Erection of G.I. pipe 100 mm dia with clamps, Nut and Bolts.(Medium Duty Class B).

Supply & Erection of Galvanised channel 125x65mm, Galvanised Angle 65x65x6 mm, Galvanised Channel 100x50mm (For AB Switch & Fuse set) .

Supply & Erection of 11 KV Polymer Pin Insulators(5KN), pin with N&B

Supply & Erection of 11 KV MS Danger Board(250x200mm) with Clamp and Nuts & Bolts

Supply & Erection of GI Holding clamps for top channel of TPMO Switch & fuse set etc. with bolts & nuts.

Supply & Erection of 3 phase 11KV TPMO with polymer insulator (1 Set=3 Nos)

Supply & Erection of 3 phase 11KV Fuse Set (Drop out) with clamps. (1 Set=3 Nos)

Supply & Erection of of G.I. Barbed Wire.

Supply & Erection of LT Unarmoured Aluminium XLPE insulated Cable of size 1Cx50 Sq.mm.

Supply & Erection of Chemical pipe earthing(80 mm dia,3 M long) for T/F neutral &body with GI Flat earthing strip by making delta earthing as per State Norms. ( B Type)

Supply & Paniting of Alluminium paint

Supply & Paniting of Red Oxide Paint

Supply & Erection of LT Unarmoured Aluminium XLPE Cable 1Cx400 Sq.mm.

Supply & Erection of Al. crimping lugs 400 sq.mm.

Supply & Erection of Al. crimping lugs 50 sq.mm.

Construction of elevated T/F plinth and foundation on 2x(9INCH*9INCH) RCC Piller upto the height of 9.8Fit from the ground level. The size of Top T/F plinth will be 1.5Mtrx1.8Mtr having the structure of GI channel of Size 125x65x6mm -2500mm for11KV DO fuse unit including cost of all civil material as TS

Supply & Erection of 11/0.4KV Copper Wound 250 KVA Transformer

Supply & Erection of Outdoor type LT Disribution Boards with a rupturing capacity of 50KA at 415V or as called for individual items (CPRI Approved manufacturer), openable in front and back suitable for 3 plase, 4 wire, 50Hz AC supply and an ambient temperature of 45 deg. C. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 as per IS 2147-1962 and IS: 8623. The panels/switches boards shall be fabricated out of 14-SWG CRCA sheet steel and provided with 16 SWG hinged doors . MAIN LT PANEL AT SUB STATION- 250 KVA (Type A-4) Incomer- 1 No. 400 Amp. TPN MCCB On/Off Indicating Light Metering on Incomer - 1 Set of Digital Ammeter with ASS - 1 Set of Digital Voltmeter with VSS - 1 Set of LED type Phase Indicating Light (22.5 mm.) with Control MCBs Outgoing - 3 Set of 160 Amp. TPN MCCB with Spreader & Extended handle - 3 Set of 100 Amp. TPN MCCB with Spreader & Extended handle (Installation of LT Distribution Boards for LT underground system (Type-A, B & C))

Plinth & foundation of Outdoor type LT Disribution Boardsfor 250 KVA Transformer

Supply & Erection of 11 KV Galvanized Stay Complete (GI Stay Rod 16x1800 mm, Anchor Plate.

Stay Set Grouting 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips (1:2:4) as per approved drawings, scope of works and TS.

Supply & Erection of GI Stay wire 7/10

Supply & Erection of Guy Insulator .

Supply & Erection of 9KV LA .5KA Distribution Class LA .( 3nos - 1set) .

Shifting of existing DT as per TS & Approved Drawings.

Supply & Erection of 11 Meter long Steel Tubular Pole SP -55.(410 SP 55)

Concreting of supports with Grounting of 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 11 mtr STP Pole of depth 1.8 meter with 300 mm Muffing.As per TS.

Supply of 11 kV XLPE insulated armoured Al. cable of size 3Cx185 sq.mm

Digging of trench for laying of Single circuit 11KV 3x185 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone after laying of cable into the trench including providing and fixing cable route marker.

Laying of 3x185 Sq. mm 11 KV XLPE insulated cable underground in cable trenches and earth filling of trenches

Hoisting of cable on double pole with the help of cable clamp with N&B of suitable size

Supply & Erection of Heat Shrinkable Termination Ki Outdoor for 11 KV 3x185 sq. mm XLPE Cable

Supply & Erection of G.I. pipe 100 mm dia with with clamps, Nut and Bolts.(Medium Duty Class A)

Supply & Erection of . Galvanised channel 125x65mm,.Galvanised Angle 65x65x6 mm, Galvanised Channel 100x50mm , with clamp & nut bolt .

Supply & Erection of 11 KV Polymer Pin Insulators(5KN), pin with N&B

Supply & Erection of 11 KV MS Danger Board(250x200mm) with Clamp and Nuts & Bolts .

Supply & Erection of GI Holding clamps for top channel /Base Channel/AB Switch & fuse set etc. with bolts & nuts.

Supply & Erection of 3 phase 11KV TPMO with polymer insulator (1 Set=3 Nos)

Supply & Erection of 3 phase 11KV Fuse Set (Drop out) with clamps. (1 Set=3 Nos)

Supply & Erection of Outdoor type LT Disribution Boards with a rupturing capacity of 50KA at 415V or as called for individual items (CPRI Approved manufacturer), openable in front and back suitable for 3 plase, 4 wire, 50Hz AC supply and an ambient temperature of 45 deg. C. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 as per IS 2147-1962 and IS: 8623. The panels/switches boards shall be fabricated out of 14-SWG CRCA sheet steel and provided with 16 SWG hinged doors in. MAIN LT PANEL AT SUB STATION- 630 KVA (Type A-2) Incomer- 1 No. 1250 Amp. TPN ACB with Inbuilt MPR Release with On/Off Indicating Light Metering on Incomer - 1 Set of Digital Ammeter with ASS - 1 Set of Digital Voltmeter with VSS - 1 Set of LED type Phase Indicating Light (22.5 mm.) with Control MCBs Outgoing - 4 Set of 400 Amp. TPN MCCB with Spreader & Extended handle - 2 Set of 250 Amp. TPN MCCB & 2 Set 100 Amp TPN MCCB with Spreader & Extended handle

Supply & Erection of Outdoor type LT Disribution Boards with a rupturing capacity of 50KA at 415V or as called for individual items (CPRI Approved manufacturer), openable in front and back suitable for 3 plase, 4 wire, 50Hz AC supply and an ambient temperature of 45 deg. C. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 as per IS 2147-1962 and IS: 8623. The panels/switches boards shall be fabricated out of 14-SWG CRCA sheet steel and provided with 16 SWG hinged doors inc. MAIN LT PANEL AT SUB STATION- 400 KVA (Type A-3) Incomer- 1 Set of 800 Amp. TPN MCCB with Spreader & Extended handle Metering on Incomer - 1 Set of Digital Ammeter with ASS - 1 Set of Digital Voltmeter with VSS - 1 Set of LED type Phase Indicating Light (22.5 mm.) with Control MCBs Outgoing- 4 Set of 250 Amp. TPN MCCB with Spreader & Extended handle - 2 Set of 100 Amp. TPN MCCB with Spreader & Extended handle.

Supply & Erection of Double Compression Weatherproof Nickel Plated Brass Cable Glands for Armoured Cable gland of suitable size along with Lugs( 4 nos Per Glands ) and all accessories

Plinth & foundation of Outdoor type LT Disribution Boardsfor630KVA Transformer

Plinth & foundation of Outdoor type LT Disribution Boardsfor 400 KVA Transformer

Supply & Erection of G.I. Barbed Wire.

Supply & Erection of LT Unarmoured Aluminium XLPE insulated Cable of size 1Cx50 Sq.mm.

Supply & Erection of Chemical pipe Earthing (80 mm dia,3 M long) for T/F Neutral and Body with GI Flat earthing strip my making delta earthing as per State Norms. ( B Type)

Supply & Paniting of Alluminium paint

Supply & Panting of Red Oxide Paint

Supply & Erection of LT Unarmoured Aluminium XLPE Cable 1Cx400 Sq.mm.

Supply & Erection of Al. crimping lugs 400 sq.mm.

Supply & Erection of Al. crimping lugs 50 sq.mm.

Supply & Erection of 11 KV Galvanized Stay Complete (GI Stay Rod 16x1800 mm, Anchor Plate.

Supply & erection of GI Stay wire 7/10 .

Supply & Erection of Guy Insulator .

Dismantling of Old ExistingTransformer and shifing to new DP then making connection in all respect.

Construction of elevated T/F plinth and foundation on 2x(9INCH*9INCH) RCC Piller upto the height of 9.8Fit from the ground level. The size of Top T/F plinth will be 1.5Mtrx1.8Mtr having the structure of GI channel of Size 125x65x6mm -2500mm for11KV DO fuse unit including cost of all civil material as TS .

Supply & Erection of 9KV 5 kA Distribution Class LA .( 3nos - 1set) .

Conversion of Overhead LT Line into Underground Cable Against Shifting of existing DTs as per TS & Approved Drawings.

Supply of 3 ½ Core ,240 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification .

Supply of 3 ½ Core ,150 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply of 3 ½ Core ,95 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply of 3 ½ Core ,25 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Digging of Trench by excavation of earth, laying of bricks to cover the cable and filling of sand & earth ramming and dressing properly with complete job for laying of LT XLPE insulated cable.

Laying of XLPE insulated ( 3.5 x240sqmm ,3.5 x150 sqmm ,3.5x95 sqmm & 3.5 x25 sqmm) cable underground in trenches inside HDPE pipe

Supply & laying of HDPE Pipe 160 mm Suitable for 3.5 C x 240 sqmm Cable by Open Trench.

Supply & laying of laying laying of HDPE Pipe 110 mm Suitable for 3.5 C x 150 sqmm Cable by Trench.

Supply & laying of HDPE Pipe 110 mm Suitable for 3.5 C x 95 sqmm Cable by Open Trench.

Supply & laying of HDPE Pipe 50 mm Suitable for 3.5 C x 25 sqmm Cable by Open Trench.

Supply & laying of HDPE Pipe 160 mm Suitable for 3.5 C x 240 sqmm Cable by HDD Method.

Supply & laying of HDPE Pipe 110 mm Suitable for 3.5 C x 150 sqmm Cable HDD Method.

Supply & laying of HDPE Pipe 110 mm Suitable for 3.5 C x 95 sqmm Cable HDD Method.

Supply & laying of HDPE Pipe 50 mm Suitable for 3.5 C x 25 sqmm Cable HDD Method.

Supply & laying of HDPE Pipe 160 mm Suitable for 3.5 C x 240 sqmm Cable by Moling Method.

Supply & laying of HDPE Pipe 110 mm Suitable for 3.5 C x 150 sqmm Cable Moling Method.

Supply & laying of HDPE Pipe 110 mm Suitable for 3.5 C x 95 sqmm Cable Moling Method.

Supply & laying of HDPE Pipe 50 mm Suitable for 3.5 C x 25 sqmm Cable Moling Method.

laying of 3.5 C x 240 sqmm Cable by HDD Method.

laying of 3.5 C x 150 sqmm Cable HDD Method.

laying of 3.5 C x 95 sqmm Cable HDD Method.

laying of 3.5 C x 25 sqmm Cable HDD Method.

laying of 3.5 C x 240 sqmm Cable by Moling Method.

laying of 3.5 C x 150 sqmm Cable by Moling Method.

laying of 3.5 C x 95 sqmm Cable by Moling Method.

laying of 3.5 C x 25 sqmm Cable Moling Method.

Supply & Erection Cable end termination using total double compression brass glands and crimping type Aluminium Thimbles( 4 nos per glands) for 3.5Cx240 sqmm

supply & Erection Cable end termination using total double compression brass glands and crimping type Aluminium Thimbles( 4 nos per glands) for 3.5Cx150 sqmm

Supply & Erection of Cable end termination using total double compression brass glands and crimping type Aluminium Thimbles( 4 nos per glands) for 3.5Cx95 sqmm

supply of Erection Cable end termination using total double compression brass glands and crimping type Aluminium Thimbles( 4 nos per glands) for 3.5Cx25 sqmm

Supply ,& Erction of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 400 amps Al. busbar. (Type-B1) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 160 Amp. TPN MCCB - 3 Nos. & 100 Amp TPN MCCB -3nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply , & Erection of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 300 amps Al. busbar. (Type-B2) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 100 Amp. TPN MCCB - 5 Nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply , & Erection of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 300 amps Al. busbar. (Type-B3) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 100 Amp. TPN MCCB - 4 Nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply & Erection of Chemical pipe earthing of Outdoor type Distribution feeder pillar Box my making delta earthing ( B Type)(80 mm dia,3 M long)

Supply & Erection GI Strip 25x3 mm .

Supply & Erection of 3-ph 415 V , Distribution Service Piller for LT. 100 Amp MCCB Incoming ,4 nos 32 Amp with Sp MCB, 12 Nos 16 Amp with SP MCB .Rating Feeder Type CRCA Distribution Service Piller suitable for Outdoor Installation.at CRCA ,as per techincal specification & drawing .

Grouting of Distribution Service Piller Box .

Supply & Erection of Pre Fabrication & Nut bolt of Distribution Service Piller Box.

Construction of Plinth for Outdoor type Distribution feeder pillar Box ( B 1Type)

Erection of Plinth for Outdoor type Distribution feeder pillar Box ( B 2Type)

Erection of Plinth for Outdoor type Distribution feeder pillar Box ( B 3 Type)

Supply & Erection of GI earthing rod of 20x2500 mm( GI solid Rod). and 6 SWG GI wire etc. together with fixing arrangement as per TS. (C-Type)

Supply & Erection GI wire 6 SWG

E. Metering

Shifting of single phase meter on the boundary wall outside the premises with all connections

Shifting of three phase meter on the boundary wall outside the premises with all connections

Providing service connection to 1-Ph Consumer meter (Connection of Meter )

Providing service connection to 3-Ph Consumer meter (Connection of Meter )

Supply & Laying of Single Phase two wire Cu. LT unarmoured PVC cable (2x4 Sq.mm.) Undergrounding .

Supply & Laying of Three Phase Four wire Cu. LT unarmoured PVC cable (4x6 Sq.mm.) Undergrounding .

Supply & Laying of Three Phase Four wire Cu. LT unarmoured cable (4x10 Sq.mm.) Undergrounding

Supply & Layng Erection of PVC pipe Heavy Gauge 50 mm dia. Inc all necessaory Assesories for LT 1-ph & 3-ph Cosumers

Dismantling of Old Existing line and carriage of dismentalled Pole/Conductor/all other material upto utility Store as per site condition.

Conversion of Overhead Street Light to Underground Cable as per TS & Approved Drawings.

Supply & Erection of armoured LT XLPE armoured cable 4x25 sq.mm armoured

Supply & Erection of HDPE Pipe 50mm (PE80 PN 6 as per IS:4984/2016 )

Supply & Erection of Heritage pole of 7.2 mtr long with all fittings

Supply & Erection of GI earthing rod of 20x2500 mm( GI solid Rod). and 6 SWG GI wire etc.

Supply & Erection of GI wire 6 SWG

Supply & Erection of LT Junction Box

Removing electric line which are creating hinderance for traffic as per TS & Approved Drawings.

Supply of 33KV, 3x300 sq.mm XLPE Cable

Digging of trench for laying of Single circuit 33KV 3x300 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 33 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Cable laying charge of 3x300 sq.mm 33KV XLPE Cable by drilling/molling method in HDPE Pipe single circuit including providing and fixing cable route marker.

Hoisting of 33Kv cable on pole and making connection

Supply of 11KV, 3x185 sq.mm XLPE Cable

Digging of trench for laying of Single circuit 11KV 3x185 sq.mm XLPE cable and making of trench for one nos cable with brick on both side, sand filling into the trench and finally trench will be covered with stone/Precast slab ("PuVVNL 11 KV HT" engraved) after laying of cable into the trench including providing and fixing cable route marker.

Cable laying charge of 3x185 sq.mm single ckt 11KV XLPE Cable by open trench method using sand, brick and patiya

Cable laying charge of 3x185 sq.mm double ckt 11KV XLPE Cable by drilling/ moling method

Hoisting of 11Kv cable on pole and making connection Including GI Pipe 110 mm

Supply & Erection of STP 13.0 Mtr long (410 SP 72)

Supply & Erection & erection of STP 11.0 Mtr long (410 SP 55)

Supply & Erection of STP 9.0 Mtr long (410 SP 33)

Excavation & Concreting (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 9 mtr STP Pole of depth 1.5 meter with 300 mm Muffing & Stone pad 300x300x75 smm. As per TS

Excavation & Concreting of supports with Grounting of 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 11 mtr STP Pole of depth 1.8 meter with 300 mm Muffing.As per TS.

Excavation & Concreting of supports with Grounting of 0.44 cum (1:2:4,1-cement, 2-coarse sand,4-concerate of 20mm Size) of 13 mtr STP Pole of depth 2.1 meter with 300 mm Muffing.As per TS.

Supply & Erection of Galvanized Channel 125x65x6mm,100x50x6, angle 65x65x6 and angle 50x50x6 as requirement

Supply & Erection of of Heat Shrinkable Termination Kit Outdoor for 33 KV 3x300 sq. mm XLPE Cable

Supply & Erection of 33KV 3X300 sq mm XLPE Straight through Cable joint /kit

Supply & Erection of Pole clamp for 11mtr STP.

Supply & Erection of G.I. pipe 150mm dia with Clamps, Nuts and Bolts (Medium Duty Class A)

Supply & Erection of G.I Pipe 100mm dia with Clamps, Nuts and Bolts (Medium Duty Class A)

Suppl & Erection of HDPE pipe 160 mm by HDD method (PE80 PN 6 as per IS:4984/2016 )

Supply & Erection of HDPE pipe 110mm by HDD method(PE80 PN 6 as per IS:4984/2016 )

Supply & Erection of GI N&B of size with washer

Supply & Erection of Dog Conductor

Supply & Erection of 11 KV Polymer Pin Insulator (5KN), pin with N&B

supply & Erection 11KV 'V' Type Cross arm

supply & Erection 11KV polymer Disc Insulator with fittings 70 KN

Supply & Erection of Galvanized Stay set 16x1800 sq mm (including stay rod, stay clamp, turn buckle,I bolt and anchor plate )

Stay Set Grouting 0.2 cmt concreting 1 part cement, 2 part sand, 4 part 40 mm size stone aggregate chips (1:2:4) as per approved drawings, scope of works and TS.

Supply & Erection Stay Guy Insulator

Supply & Erection Stay Wire 7/10 SWG

Supply & Erection of GI Earthing rod (2500X20mm)

Supply & Erection of Heat Shrinkable Termination Kit Outdoor for 11 KV 3x185 sq. mm XLPE Cable

Supply & Erection of Cable Jointing kit H&S, 11KV, 3x185 sq.mm S/T

Supply & Erection of Sackle Insulator

Supply & laying of 3 ½ Core ,240 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply & laying of 3 ½ Core ,95 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply & laying of 3 ½ Core ,150 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply & laying of 3 ½ Core ,70 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply & laying of LT Unarmoured Aluminium XLPE Cable 1Cx400 Sq.mm.

Supply & Erection of Double Compression Weatherproof Nickel Plated Brass Cable Glands for Armoured Cable of suitable size along with all accessories

Supply & Erection of Chemical pipe earthing (80 mm dia,3 M long) ( B Type)

Supply & Erection of Single Phase two wire Cu. LT armoured PVC cable (2x4 Sq.mm.) incl. Clamp & Assessories

Supply & Erection of Three Phase Four wire Cu. LT armoured PVC cable (4x6 Sq.mm.) incl. Clamp & Assessories

Supply & erection of Three Phase Four wire Cu. LT armoured cable (4x10 Sq.mm.) incl. Clamp & Assessories

Supply & Erection PVC pipe Heavy Gauge 25 mm dia. Inc all necessaory Assesories for LT 1-ph & 3-ph Cosumers

Supply & Erection of LT XLPE Cable AL. 3.5x95sq.mm

Supply & Erection of ACSR Weasel Conductor

Supply & Erection of Barbed wire

Supply & Erection of LT MS Number Plate with Clamps and GI Nuts & bolt

Supply & Erection of 33 KV Polymer Pin Insulatorwith pin (10 KN) & with N&B

Supply & Erection of 33 KV 'V' Type X-Arm

Supply & Erection of G.I.Wire 6 SWG

supply & Erection of LT Piercing connector

supply & Erection of LT Suspension clamp with I-hook

Supply & ErectionLT Dead end clamp with I-hook

Supply & Erection of 11 KV MS Danger Board(250x200mm) with Clamp and Nuts & Bolts

Supply & Erection of 3 phase 11KV TPMO with polymer insulator and clamp (1 Set=3 Nos)

Supply & eEection of 3 phase 11KV Fuse Set (Drop out) with clamps. (1 Set=3 Nos)

Supply & Erection of Pole mounted LT Distribution pannel openable in front and back suitable for 3 plase, 4 wire, 50Hz AC supply and an ambient temperature of 45 deg. C. The Cubicle should be weather proof, dust proof, vermin Proof .The panels/switches boards shall be fabricated out of 14-SWG CRCA sheet steel. Incomer- 1 Set of 800 Amp. TP MCCB with Extended Busbar and Out going - 3 set 200Amp. TP MCCB with bus bar arrangement.

shifting of 6 – way Distribution feeder pillar, TP & N , 3 phase ,415 v , 315 Amps incoming rating type suitable for outdoor installation , in accordance with Technical Specification

Shifting of 3-ph 415 V , Distribution Service Piller for LT. 100 Amp Incoming 4 nos 32 Amp, TPN 12 Nos 16 Amp SPN.Rating Feeder Type Distribution Service Piller suitable for Outdoor Installation.

Supply & Erection of LT Unarmoured Aluminium XLPE Cable 1Cx630 Sq.mm.

Supply & Erection of LT Unarmoured Aluminium XLPE Cable 1Cx240 Sq.mm.

Supply & Erection of LT Unarmoured Aluminium XLPE insulated Cable of size 1Cx50 Sq.mm.

Supply & Erection of Alluminium paint

Supply & Erection of Red Oxide Paint

Supply & Erection of Al. crimping lugs 630 sq.mm.

Supply & Erectionof Al. crimping lugs 240 sq.mm.

Supply & Erection of Al. crimping lugs 50 sq.mm.

Supply & Erection of Allu. lug 400sq.mm

Supply & Erectionof Aluminum lugs -300 Sq.mm.

Supply & Erection of Aluminum lugs -185 Sq.mm.

Supply & Erection of Outdoor type LT Disribution Boards with a rupturing capacity of 50KA at 415V or as called for individual items (CPRI Approved manufacturer), openable in front and back suitable for 3 plase, 4 wire, 50Hz AC supply and an ambient temperature of 45 deg. C. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 as per IS 2147-1962 and IS: 8623. The panels/switches boards shall be fabricated out of 14-SWG CRCA sheet steel and provided with 16 SWG hinged doors inc. MAIN LT PANEL AT SUB STATION- 400 KVA (Type A-3) Incomer- 1 Set of 800 Amp. TPN MCCB with Spreader & Extended handle Metering on Incomer - 1 Set of Digital Ammeter with ASS - 1 Set of Digital Voltmeter with VSS - 1 Set of LED type Phase Indicating Light (22.5 mm.) with Control MCBs Outgoing- 4 Set of 250 Amp. TPN MCCB with Spreader & Extended handle - 2 Set of 100 Amp. TPN MCCB with Spreader & Extended handle.

Plinth & Foundation for Outdoor LT Distribution Board

Supply & Erection of LT straight through joit kit for 3.5x240 sq.mm

Supply & Erection of LT straight through joit kit for 3.5X150 sq mm

Supply & Erection of LT straight through joit kit for 3.5X70 sq mm

Supply & Erection of LT A B Cable Size (3x120+1x95+1x16) sq mm with Bare Massenger

Supply & Erection of Three phase LT SMC Box with Clamps

Supply & Erection of copper Z clamp for 400 KVA T/F with nut bolt & washer

Supply ,& Erction of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 400 amps Al. busbar. (Type-B1) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 160 Amp. TPN MCCB - 3 Nos. & 100 Amp TPN MCCB -3nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply , & Erection of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 300 amps Al. busbar. (Type-B2) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 100 Amp. TPN MCCB - 5 Nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply , & Erection of outdoor type feeder pillar panel to be made of 2 mm CRCA sheet and covers will be 1.6mm CRCA sheet duly powder coated paint with 300 amps Al. busbar. (Type-B3) Incomer - 250 Amp. TPN MCCB - 1 No. Outgoing - 100 Amp. TPN MCCB - 4 Nos. The Cubicle should be weather proof, dust proof, vermin Proof and enclosure protection shall be IP-55 (suitable for outdoor applications) as per IS

Supply & Erection of 3-ph 415 V , Distribution Service Piller for LT. 100 Amp Incoming, 4 nos 32 Amp SP, 12 Nos 16 Amp SP.Rating Feeder Type Distribution Service Piller suitable for Outdoor Installation.

Grouting of Distribution Service Piller Box .

Supply & Erection of Pre Fabrication & Nut bolt of Distribution Service Piller Box.

Supply & Erectionof 3 ½ Core ,25 sqmm. Armoured Al conductor XLPE insulated 1.1 kV grade armoured Power cable as per Technical specification.

Supply & Erectionof GI Pipe 15mm dia

Shifting and connection of single phase meter on the boundary wall outside the premises with all connections

Shifting and connection of three phase meter on the boundary wall outside the premises with all connections

Dismantling of service pillar, feeder pillar & LTDB

Erection of DT FENCING- Fencing around the Distribution transformer by WPC Board as per TS & Approved Drawings.

Supply & Erection fabrication of GI angle of size 65x65x6mm for Designer board support

Supply & Erection fabrication of GI angle of size 50x50x6mm for Designer board support

Grouting of GI angle support after digging of pit, 3 fit below the groud level to fabricate the structure as per norms

Providing & fixing of specially designed WPC board by CNC cutting machine All around the transformer on plinth with the help of fabricated structure of GI Angle 65x65x6mm

Providing and fixing of openable gate in designed MDF board with all fixing and locking arrangement.

Software for Control Centre As per TS

SCADA Server

DMS Server

OMS Server

FEP server with interface switches

ISR server

NMS server

DTS server

Developmental server

Commnuication Server

Web/Directory server

SMS gaterway

Workstation with dual TFT Monitors ( S/S monitoring)

Workstation with dual TFT Monitors (Network monitoring)

Remote VDUs with one TFT Monitors

Developmental console with one TFT

DTS/Workstation Console with dual TFTs

DLP/ LED based Video Projection system with 3x4 Module configuration with each module at least 67" diagonal with common projector

Storage & Backup Devices

External RAID Mass storage device ( for 24 months online backup)

Exteranl DAT drive

Switches

Layer II switch (SCADA/DMS LAN)

Layer II switch ( Planning & Development system LAN)

Routers

Router for interfacing IT system & SCADA/DMS DR centre

Router at remote VDU

Security system (DMZ)

Web server with load balancing

Mail server

Router

Firewall & network IDS/IPS

Layer II switch

Other Active Devices

GPS Time synchronisation system

Time, day & date digital displays

Printers

Color inkjet printer

B/W Laser printer

Software For Control Center

SCADA software

ISR Software

DMS software

OMS Software

DTS software

Developmental software

Network Management Software

RDBMS package

GIS Adaptor/Engine for importing data from GIS system under IT system

Mandatory Spares

Hardware For DR Center As per TS

SCADA Server

DMS Server

OMS Server

FEP server with interface switches

ISR server

NMS server

DTS server

Developmental server

Commnuication Server

Web/Directory server

SMS gaterway

Workstation with dual TFT Monitors ( S/S monitoring)

Workstation with dual TFT Monitors (Network monitoring)

Developmental console with one TFT

DTS/Workstation Console with dual TFTs

DLP based Video Projection system with 3x4 Module configuration with each module at least 67" diagonal with common projector

Storage & Backup Devices

External RAID Mass storage device ( for24 months online backup)

External DAT drive

Switches

Layer II switch (SCADA/DMS LAN)

Layer II switch ( Planning & Development system LAN)

Routers

Router for interfacing IT system & SCADA/DMS DR centre

Security system (DMZ)

Web server with load balancing

Mail server

Router

Firewall & network IDS/IPS

Layer II switch

Other Active Devices

GPS Time synchronisation system

Time, day & date digital displays

Printers

Color inkjet printer

B/W Laser printer

Software For DR Center As per TS

SCADA software

ISR Software

DMS software

OMS Software

DTS software

Developmental software

Network Management Software

RDBMS package

GIS Adaptor/Engine for importing data from GIS system under IT system

Mandatory Spares

RTU base equipment comprising panels, racks, sub-racks, Power Supply modules, CPU, interfacing equipment, required converters & all other required items/accessories including complete wiring for all modules for locations mentioned at Vol Vi (Should be compatible for IEC 62056 along with other protocols metioned in SBD)

Multifunctuions transducers

Contact Multiplying Relays (CMRs)

Heavy duty relays for Control

Dummy Breaker Latching Relays

Transformer Transducers

Single TFT PC for LDMS

Software For LDMS

LDMS software

TEST EQUIPMENTS for RTU

RTU Database Configuration & Maintenance Software tool

Master Station cum RTU Simulator & Protocol analyser software tool

Laptop PC for above software tools along with interfacing hardware including Hub

Mandatory Spares

FRTUs

Mini pole mounted FRTU base equipment along with enclosure suitable to work in open environment (Adequate protection from water & dust) , racks, sub-racks, Power Supply modules with power backup , I/o modules, CPU, interfacing equipment, required converters & all other required items/accessories including complete wiring for all modules for locations mentioned at Vol Vi

Contact Multiplying Relays (CMRs)

Heavy duty relays for Control

Multifunction trnasducer

Test Equipments for FRTU

FRTU Database Configuration & Maintenance Software tool

Master Station cum FRTU Simulator & Protocol analyser software tool

Laptop PC for above software tools along with interfacing hardware including Hub

Mandatory Spares

Annual charges for 100MBps Links with RTUs

MPLS Router

Annual charges for 2MBps Links with FRTUs /FPI

Modems

Mandatory Spares

Main Equipments - Control centre

UPS with suitable rating running in parallel redundant mode*

Main Equipments - DR Centre

UPS with suitable rating running in parallel redundant mode*

For RTU / Data Concentrator / Communication Eqpts.

DC Power Supply (DCPS) system based on SMPS

For FRTU

24 V DC Power Supply (DCPS) system based on SMPS

Remote VDU location

UPS (2 kVA )

Mandatory Spares

Supply & Erection SECTIONLIZER

11 Kv Sectionlizer .Rod Type Earthing complete with GI strip(1 nos) & structure

Supply & Erection 11 Kv FPI Communicable

Numerical relay

Numerical relay /BCPU

SCADA Compatible RMUs

Supply & Erection of Outdoor type 11 KV SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with One VCB and two LBS,FPI & FRTU along with supply through 1 kVA auxilliary power transformer 11/0.230 KV as per Discom Specs along with other allied material like cable, ternination kits etc. to connect the same with system Rod Type Earthing complete with GI strip ( 2 nos) & foundation work

Supply & Erectionof Outdoor type 11 KV SF6 type extensible and motorized 4 way smart Ring Main Unit (RMU) complete with two VCB and two LBS, FPI & RRTU along with supply through 1 kVA auxilliary power transformer 11/0.230 KV as per Discom Specs along with other allied material like cable, ternination kits etc. to connect the same with system Rod Type Earthing complete with GI strip ( 2 nos) & foundation work

Supply & erection of Outdoor type 11 KV SF6 type extensible and motorized 5 way smart Ring Main Unit (RMU) complete with three VCB and two LBS ,FPI & FRTU along withI along with supply through 1 kVA auxilliary power transformer 11/0.230 KV as per Discom Specs along with other allied material like cable, ternination kits etc. to connect the same with system Rod Type Earthing complete with GI strip ( 2 nos) & foundation work

Supply & Erection of Outdoor type 33 KV SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with one VCB and two LBS with FPI & FTRU along with supply through 1 kVA auxilliary power transformer 11/0.230 KV as per Discom Specs along with other allied material like cable, ternination kits etc. to connect the same with system, Rod Type Earthing complete with GI strip ( 2 nos) & foundation work

Facility Managament Services for 5 Years after GO-LIVE

DT Health Management ( DTMH)

Lug temperature Sensors

Oil Level Sensor

Oil Temperature Sensors

4G Gateway

Any other sensor

Software as a Service (SaaS) based web-dashboard( 12 Month)

Annual Maintenance ( 12 month)

Drone based asset management

Supervisor

Drone rental

Payload rental

Data collection

Transportation

Demand Response

Autogrid - 50 k participants (Annual License &Integration)

Autogrid - 200 k participants (Annual License &Integration)

Autogrid - 250 k participants (Annual License &Integration)

Consumer & LV Network Analytics two year support

System integration cost (one-time)

Platform fee

Data processing & reporting charges

P2P Energy Trading

One-time Platform Development & License Fee (USD 250K)

Onboarding Fees for Users (Assuming 200 Consumers/Prosumers, USD 20/user)

IoT Based Monitoring of HV Switchgear

Thermography Sensors

Humidity and Ambient Temperature Sensors

Partial Discharge Sensors

DCU for high voltage environment

Sofware for dashboarding and reporting

Compack Substation

Supply & Erection of Outdoor type 11 KV SF6 type extensible and motorized 3 way smart Ring Main Unit (RMU) complete with One VCB and two LBS,FPI along with FRTUwith supply through 1 kVA auxilliary power transformer 11/0.230 KV as per Discom Specs along with other allied material like cable, ternination kits etc. to connect the same with system Rod Type Earthing complete with GI strip ( 2 nos) & foundation work As per TS

Supply & Erection 11 kv/415V,400KV oil cooled Transformer with of load tap changer

Supply & Erection of 11 kv/415V,1000KV oil cooled Transformer with of load tap changer

Supply & Erection LV SB 413, 3P,800A Air Circuit Breaker as Incomer and 4 nos 3P.630A,MCCB As outgoing Feeder having separate DT Meter compartment

Supply & Erection LV SB 413, 3P,1600 A Air Circuit Breaker as Incomer and 4 nos 3P.630A,MCCB As outgoing Feeder having separate DT Meter compartment

Supply & Erection Automatic Power Factor coorection panel of 300 KAVR capacitor bank ,contractors and intellegent power factor correction Relay

Supply & Erection Automatic Power Factor coorection panel of 120 KAVR capacitor bank ,contractors and intellegent power factor correction Relay

Supply & Erection of DTHM software platform fee for 12 months

Voltage Regulation and Harmonics Management

Power Quality Meter/ Analyser

Active Harmonics Filter

Smart Inverter (Pilot)

Substation/Network Health and Safety

Video Survelliance

Thermal Imaging (Fixed Camera)

Back-up hardware, software and cloud/ server storage

Heat and Smoke Detectors (Roof mounted)

Silicon Sleeves for OH conductors

Insulated Poles

Joint Box/Kits

Hand held Cameras

PPE and accessories

GIS Mapping Update and Integration

Asset survey update

GIS software operations and maintenance (AMC)

GIS software Integration with AMI

Network Planning Tool

Network Planning Tool

PD Analytics Solution / Equipment for U/G cabling

Supply of PD Analytics Solution / Equipment for U/G cabling

Cloud based DERMS application for 5000 RE Prosumers (Solar Rooftop etc. )

Montecarlo Limited (BID ID -4622030)

Jakson Limited (BID ID -4712246)

Bidder Name

Jakson Limited

Montecarlo Limited

LARSEN AND TOUBRO LIMITED