ADDN/ALTN AND SPECIAL REPAIRS TO BLDG NO. TA-09 AND T-37A OF MED REGT AT AJMER, SPECIAL REPAIRS OF BARRACK NO. 5 OF RMS AT AJMER, ADDN/ALTN OF BLDG NO. 10 (OLD CADET MESS) OF RMS AND MINOR WORK AT AJMER MIL CANTT UNDER GE NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling inlcluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finishedeven and smooth without using extra cement, complete all as specified and directed.

M & L for preparation new plastered surfaces of walls and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

M & L for preparation old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and applying two coats of oil bound distemper of approved shade over a coat of primer over 1 mm thick wall care of putty complete all as specified and directed

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer over 1 mm thick wall care putty complete all as specified and directed

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old concrete surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring of size not less than 550X550mmX18-20mm thick over 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado, window cills and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match including rubbing & polishing complete all as spd & directed.

M&L for cement 25 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in sub base of floor, complete all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified & directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding, and rubbish off premises etc complete all as specified and directed.

M&L for glazed ceramic coloured tiles, size 450 mm X 350 mm, 6-7 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over 10 mm thick screed plaster in CM 1:4 complete all as specified and directed

M & L for Non-skid Ceramic tiles 7 to 8 mm thick ( Square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

All as per the item No 17.00 above but as in skirting over 10 mm screed plaster in CM 1:4 complete all as specified.

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge. Make: Everest/Armstrong

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roof fixed with L-type or J-type or cranked hook bolts complete all as specified & directed.

All as per srl item 22.00 above but except sheets.

M&L for asbestos cement two piece adjustable plain wing ridge 6 mm thick complete all as spd & directed.

S & F second class HW 35mm thick, factory made, plain framed, paneled shutter (Two panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

Supply and fixing for 2nd class HW 35 mm thick, gauged and skeleton shutters (Two Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned & chemically pressure treated complete all as specified and directed.

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M S square tube, supplying and fixing in opening as per specification and drawing completeall as specified and directed

Supply and fixing of 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description n exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

S&F 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

Demolition of stone/brick masonry built in cement or cement lime mortar all as specified and directed.

M&L for old size brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

All as per serial item No. 42.00 above but except brick.

M&L for old size brick work with fly ash bricks straight or curved on plan to any radius in half brick thick wall, built in CM 1:4 complete all as specified and directed.

M&L for providing chequered cement concrete coloured tiles 25cm x 25cm x 22 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment laid over and including screed bed or bedding layer 20 mm thick in cm 1:4 as in floors complete all as specified and directed.

M & L for 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone agg as in sub base etc complete all as specified and directed.

M & L for PCC 1:2:4 type B-2, using 40 mm graded stone agg as in surface channel & drain etc complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but n. exc 2.00 sqm each leaf and removing from site.

Taking down existing unservicable treatment of any description including cement plaster/cement concrete of any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed.

M&L for five layered APP modified polymeric water proofing membrane , 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00 Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for PCC 40mm thick (minimum consolideted thickness) type B-0, using 12.5 mmgraded stone aggregate as in padding finished even and smooth wothout using extra cement with existing slope with V shaped grooves 6mm wide and10mm deep @0.40Sqm of each panel on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

S&F in repairs vitreous china wash down water closet squatting pattern ( Urissa pattern) with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed.

S&F in repairs Vitreous China Urinal, Half stall type, white including connections to flushing pipe and outgoing pipes fixed in repairs complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float and handle fixed on walls by driling holes and using PVC rawl plug of suitable size complete al as spd & directed.

S&F in repairs wash hand basin vitreous china white / ivory colour flat size 550 x 400mm fixed including waste coupling, waste pipe & connection pipe complete all as specified and directed

S&F in repairs stop valve 15 mm bore cast copper alloy fancy type ISI marked chromium plated with long shank & cup (concealed type) screwed down high pressure screewed both ends for iron pipe complete all as spd & directed.

S&F in repairs 15mm bore PVC connection 45cm long with 2 Nos PTMT nut at both ends complete all as spd & directed.

S & F in repairs 15 mm bib taps standard of PTMT any colour high pressure screwed for iron pipe ( minimum weight 90 grams) complete all as specified and directed

S&F in repairs pillar taps fancy type cast copper allloy capston headed, chromium plated, screwed down, high pressure with long screwedshank and fly nut, screwed for 15mm bore iron pipe complete al as spd & directed.

S&F in repair brass chromium plated shower rose of 125mm size with swivel joints, incl . Fixing to steel pipe or union of 15mm bore complete all as specified and directed.

S&F in repairs angle valve 15mm bore cast copper alloy fancy type ISI marked chromium plated with long shank & cup screwed down high pressure screewed both ends for iron pipe complete all as spd & directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item No. 64.00 above but 20 mm bore.

All as per srl item 64 above but 25.00 mm bore.

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item No. 67.00 above but 20 mm bore.

All as per srl item No. 67.00 above but 25 mm bore.

Fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc complete all as specified and directed.

All as per srl item No. 70.00 above but 20 mm bore.

All as per srl item No. 70.00 above but 25 mm bore.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

Supply only water proofing compound ISI Marked complete all as specified and directed.

M&L for random rubble stone walling uncourses, built in CM (1:6) complete all as specified and directed.

All as per serial item No. 79.00 above but except stone.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm as specified.

M & L for 20 to 25 mm thick machine cut kota stone shelves including rubbing & polishing, set in CM (1:4) incl cutting inserting into wall not less than 50mm deep and making good to disturbed surfaces complete all as specified and directed.

S & F 125mm double action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

Taking out of old grill & M & L framed work such as grills, gratings, etc, with ends of bars shouledered and /or reiveted ,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work coforming to Fe 290m Gde E-165 complete all as spd and directed.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook, complete all as specified & directed.

Dismantling of timber scantling 40 Sq cm and over in section as in framed work in any position complete.

S & F framed work as in roof trusses purlin, rafter and batterns of angle or other section with gusset plates , rails , braces, etc complete of Fe 410-W (Gde E-250) , drilling for fixing of steel sheeting or other covering doors etc to be prepared for hanging complete all as spd and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of wall and applying three coats of white wash complete all as specified and directed

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

Taking out old un serviceable tubular towel rail & S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S&F in repairs Chromium plated stop cock 15 mm dia screwed down light pressure screwed both ends for iron pipe or for union complete all as spd & directed

S&F in repairs CI Nahani/Floor trap 75 mm outlet with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as complete all as spd & directed

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Dismantling of existing unserviceable water tank of any description capacity exc 250 Ltr but n.exc 500trs capacity each complete all as specified and directed

Supply and fixing 500 Litre capacity rotational moulded polyethylene water storage tanks, white colour, double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as spd & directed.

M&L for 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and M&L 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) finished concrete surfaces even & smooth complete all as specified and directed

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc complete all as specified.

Taking down CI pipe 100/75 mm fixed wall and floor etc including accessories complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only old serviceable 100 mm bore CI pipe retrieved from item No. 107.00 as on wall with fixing clamps.

S& F 100 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only old serviceable 75 mm bore CI pipe retrieved from item No. 107.00 as on wall with fixing clamps.

S& F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

S& F 100 mm CI bend, fixed with cement solvent complete, all as specified and directed

M&L for 35 mm thick (measured solid), precast cement concrete (1:2:4 type B0 using 12.5mm graded crushed stone aggregate) louvers and jallies, including all mouldings but excluding frame, set in CM 1:6, complete, all as specified & directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

S&F sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 4.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

S&F sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed in and including non metallic rigid PVC concealed conduit 20 mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including one green colour cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Engr-in-Charge of following. Make of wire: Polycab/Finolex/Havells, Conduit: Anchor/Polycab/Finolex

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 119.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

Supply and fixing of switch piano type, flush button single pole, one way 5 Amps, complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing of switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing of socket outlet 5 Amps, 5 Pin, flush type, complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing of socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all, as specified & directed. Make : Cona / SSK / Havells

Supply and fixing stepped type ( switch type) electronic ceiling fan regulator flush type, AC, 230 volts , complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing of ceiling rose,surface type bakelite 65x17.5 mm, three terminals, complete all as specified and directed. Make : Cona / SSK / Havells

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired . Make Havells/Bajaj/Philips/Crompton

Supply and fixing LED lamp 9/10 watt , 230 volts , 50 Hz, B-22 base for fixing in lamp holder and wall mounted decorative light fitting complete all as specified and directed. Make : Bajaj / Philips / Havells

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make:- Havells Cat part NoPHOTONULTRA2.01212T8SSTL20WLED 865SPC (for tube) REGALBATTENT8UPTO1X22WDSBSWH (for batten)Bajaj Cat Part No BLRB 18W CWc for tube , BLRB - DB 118 for batten , or equivalent model of Philips/Crompton

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed. Make :- Havells Cat Part No LHEOAP7UZ6W010 or equivalent model of Philips/Crompton

Supply and fixing and testing energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make : Havells, Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC, or equivalent model of Crompton/Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB distribution board triple pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 415 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Supply and fixing of MCB SPN 10 to 40 Amp capacity, 10KA , 'C' curve complete all as specified and directed. Make :- : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Supply and fixing of MCB TPN 63 Amp capacity,415 volt complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make:- Havells/Bajaj/ Usha

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed. .

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unserviceable existing earthing complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly complete all as specified and directed.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all as specified and directed. .

Supply and fixing tubes light grade GI tubing 50 mm dia with all fitting laid in trenches complete all as specified and directed.

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size.

SHREE GURU NANAK CONSTRUCTION COMPANY

Abdul Gani Abdul Sattar