PROVISION TOILET NEAR TRADESMAN SHOPPING COMPLEX, GEYSER IN BUILDING NO P 19AND SPECIAL REPAIR TO BLDG NO ENP 06, WIRING IN BLDG NO P 43 TO 50 INCLUDING OTHER CONNECTED WORKS AT ASC CENTRE AND COLLEGE UNDER AGE BR-I AND AGE EM OF GE CENTRAL BANGA

Amount

B/R PORTION : - Dismantling of Asbestos Cement Corrugated or Semi-corrugated sheeting, any gauge, thickness, in roof covering including ridges complete as directed. (measured flat overall)

Dismantling timber boarding, any description, fixed in any position with nails complete all as specified and directed.

Demolition of brick work/concrete block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debrises out side MD land complete all as specified and directed.

Cutting into existing manholes for inserting new drain pipe, 150mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

Taking down eaves gutter and rain water pipes (any size or pattern) including fittings heads, shoes, bends, swan necks etc (measured overall as fixed along the centre line over fittings and acessories) complete all as directed.

S & F 0.80 mm thick plain galvanised steel sheeting conforming to IS 277 having minimum grade of zinc coating @120 gm per square metre, as in valley, gutters, drip and straight flashings complete all as directed.

M & L for surface excavation averaging 15cm deep and n.exc 30cm deep and getting out as in soft/loose soil including removing the soil to a distance exc 250M but not exc 500 M and depositing where directed complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance exc. 1.50 KM but not exc 5 KM and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for moorum/sand/red bajri filling under floors or in foundations laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

Supply and fixing RCC pipe, 150mm bore, class NP-3, laid and jointed with collar complete all as directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in bed to drain pipes and forming cradles against the sides of pipes after they are laid and tested complete for 150 mm bore PVC/DWC/RCC drain pipes complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in slabs supported on walls, beams and column in floors, roofs, landings, balconies and in shelves and the like complete all as specified and directed.

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, balconies and in shelves and the like for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Form work to sides/edges of concrete flats, floor and roofs, in walls, horizontal or slopeing and the similar work, 10cm to 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, manhole etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

S & F 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with screws/nails in any situation as in eaves board, etc complete all as specified and directed.

Fixing only second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with by using new screws/nails in any situation as in eaves board, etc complete all as specified and directed. Note : - Old serviceable timber boarding retrieved under item No 02 shall be used.

S&F 30mm thick Flush shutters, solid core construction, with block board core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

M & L for pressed steel frame of size 125mmX60 mm made out of 1.25mm thick plain black steel sheet for door with one or more rebates including supply and fixing by welding necessary lugs, hinges, lock plate and PCC filling into frame using plain cement concrete 1:2:4, type B0 etc complete all as specified and directed.

S & F box type steel windows/ventilators double side shutters ie glass and wire mesh shutter, including pressed steel frames made out of CRCA sheet of 80X60X1.25mm thick double rebated, shutters box type made out of CRCA sheet of 40X20X1.0mm thick, 12mm square guard bar/grill welded to steel frame, window shutters side hung, ventilator shutters top hung, box type hinges, aluminium die cast handles for glass shutters, iron flat type handles for mesh shutters, telescopic stays etc complete all as specified in TD drawing No TD/539 dated 09.02.2004 of Chief Engineer Chennai Zone and PCC filling into frame using plain cement concrete 1:2:4, type B0 etc complete all as specified and as directed . NOTE:- (i) Quoted rate under this item shall deemed to be inclusive of steel frame, both side steel shutters, guard bars/grills, handles, telescopic stays, beading/fillets for fixing glass/wire mesh including cost elements for fixing of glass & wire mesh and mearurement/ payment shall be considered as one unit by comprising all these elements. (ii) Glass and wire mesh shall be measured and paid as supply only separately under respective item.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws for PVC door complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

Supply only 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 4 mm thick, sheet glass, pin head/figured glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F band, straps, supports or stays for rainwater pipes, ventilating pipes, including bolts if required hooks (stay), heavy duty, for large gate, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and the similar small articles drilling holes for bolts etc conforming to Fe-290 Gde- E-165 all as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

S & F for false ceiling of 4mm thick HSPC (High Presure Steam Cured) pre-primed self embossed texured designer ceiling board, cement fibre board of size 595X595 mm (E-Board Classic, white colour) to be fixed in and including GI snap grid with rool formed out of hot dip galvanised steel capings (Powder coated finished) 600X600 mm system. The suspension system consisting of perimeter wall angle of size 38X24X0.90mm of thick GI sheet to secure on wall portion fixed with the help of rawl plug @ 450mm centre to centre universal main runner of T shaped section with single rotary stitching of size (32X24X0.9 mm) made from 0.0.9mm thick GI sheet of length 3.60 metre to be spaced @ 1200 centre to centre cross runner T shaped with double rotary stitching of size (28.6X24X0.9 mm) of length 1200mm made from 0.90 mm thick GI sheet spaced @ 600mm centre to centre (1200X600mm) of size module intermadiate T shaped cross runner of size (28.6X24mm) of length 600mm made of 0.0.90mm thick GI sheet to form (600X600mm) size of module including suspension of the ceiling from the roof/structural members, soffits angles, cleats, by using GI suspenders of 3mm dia GI wire and level adjusters including U clamp of GI fixed in ceiling all complete and making opening by cut out the ceiling board for ceiling light fittings as required and as per manufacturer's instruction or as directed by Eng-in-charge. Make :- Eternit Everest / lafarge/ Armstrong or equivalent as approved by GE

All as per item No 48 above but fixing only using old serviceable ceiling materials retrieved under BOQ item No 08 here-in-before.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for non-skid, ceramic, joint free of matt finish, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, jint free of matt finish, coloured tiles 8 to 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.36 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for ceramic, coloured tiles 7 to 8 mm thick as in skirting/ dado/ vertical surface to match the length of floor tile procured under No 52 above including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, joint free of matt finish, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, 300x600mm X 7 to 8mm thick as in skirting/ dado/ steps including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, etc complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in coping, kneelers, bed plates etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceilings (sunshed, chajja, fins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer to plastered and other surfaces including providing wall care putty two coats in 1 to 2 mm thick on plastered surface complete all as specified.

M&L for complete removal of existing treatment of wall and applying two coats of 100% premium acrylic emulsion paint having VOC not less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of approved tint/shade (Company depot tinted) with silicon additive @ 1.43 litre/ 10 Sqm over and including applying priming coat of exterior primer @ 0.90 litre/10 Sqm over new/old surfaces of wall complete all as specified.

M&L preparation of plastered surfaces of wall and applying two coats of 100% premium acrylic emulsion paint having VOC not less than 50gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of approved tint/shade (Company depot tinted) with silicon additive @ 1.43 litre/ 10 Sqm over and including priming coat exterior primer applied @ 0.90 litre/10 Sqm over new surfaces of wall complete all as specified.

M & L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces ofceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparation external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (Apex ultima superior quality) paint over a coat of primer as per manufacturer's instruction including providing 1 to 2 mm thick wall care putty complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of old or previously treated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Taking up or down 15mm bore, Steel tubing and connections.

Taking up or down 20mm bore, Steel tubing and connections.

Supplying and laying of 16mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 15 mm bore bib taps (bearing ISI marked) cast copper chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: Jaquar/CERA /HindwareKohler//Parryware/Somany

S&F 15 mm bore stop valves (bearing ISI marked) cast copper alloy chromium plated high pressure with capstan head screwed both ends for iron pipe or for unions complete all as specified and directed. Make: Jaquar/CERA /HindwareKohler//Parryware/Somany

S&F Vitreous China Urinal, bowl type (approximate size 340X280X470mm), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar; fixing flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to urinal/flushing cistern, trap and waste pipe). Make : CERA Cat No S4020103/Prayag Cat No 4999 or equivelent of Parryware/Hindware

S & F vitreous China wash down water closet pan (pedestal pattern), coloured, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with recess bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long and 32mm dia flush pipe, S or P Trap & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make of Pan CERA Cat No S3010108 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, including provision of chromium plated fancy type long neck pillar tap with capstan head suitable for 15 mm bore pipe, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, 45 cm long PVC connections including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2040105 or equivelent of Parryware/Hindware/Prayag

S & F brass, chromium plated, 15mm bore wall mixer with L bend for mixing hot and cold water, screwed down with provision of over head shower and cock for iron pipe and fixed complete all as specified and directed. Make: PRAYAG Cat No BS -31/ CERA Cat No F7020302CH or equvelent of Make Hindware/Parryware/CERA

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle brackets including 15mm dia 450 mm long, PVC connection pipe with PTMT nut and washer complete all as specified and directed. Make CERA Cat No B1010109 or equivelent of PRAYAG/HINDWARE/Parryware

S&F 15 mm bore bib taps fancy type with flange cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO QT-F3001151/PRAYAG Cat No 7306 or equvelent of Make Hindware/Parryware

S&F 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: PRAYAG cat No 7226/CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware

S & F brass chromium plated tubular towel rail, 20mm dia 'D' type, 600mm long between flanges complete all as specified and directed. (Make: CERA Cat No F5004103/PRAYAG Cat NO BA-20 or equivalent of Parryware /Hindware)

S&F rotational moulded polyethylene water storage tanks 500 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple, union suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head including taking down old unserviceable tank and removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple, union suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head including taking down old unserviceable tank and removing from site complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

E/M PORTION : - (EARTH WORKS AND CONCRETE WORKS IF ANY RELATED TO E/M WORKS SHALL BE MEASURED AND PAID UNDER RESOECTIVE ITEM CATERED IN B/R PORTION) : Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one switch

All as per item No 97 above but for one 3 pin socket point 5 Amp on independent board

All as per item No. 97 above but with 2.5 sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose Make : Anchor/Cabtree/Legrand/Standard

Supply and Fixing water electric heater/gyeser, storage vertical type and heating element of 2 KW, any colour, 25 Litre capacity, BEE 5 star rated complete with all acessories, making neccessary electrical connection, 15 Amp 3 pin plug & testing on completion all as directed. Make : Racold/Orient Electric/Usha/Bajaj/VENUS

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, TPN 4 way vertical type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 4 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix Sheet metal enclosure (ISI marked) distribution board for 240 volts, 2 way with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix isolator 3 pole 40 Amps, 415 volts, 25 KA rupturing capacity

Supply and fix MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

S&F in replacement Pride plus inverter batten of make Havells, LED tube light fitting of 20 watts 6500K , 230 volt, with polycarbonate channel , lithium Ion battery with charging time 8-10 hours and back up time 4 hours complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7FN1W020 OR equivelant of make Crompton Greaves/Bajaj/Philips/Wipro

S&F new generation energy saving environmental friendly long life, with high power LED building street light/security light 1x 30/25 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 protection and impact resistant of IK7 prewired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make:- Superb street light of Havells Cat No LHEXAYP7PN6K030 or equivelent of Crompton Greaves/Bajaj/Philips/ Wipro

S&F security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for Sub main wiring with two runs of 2.5 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables conforming to IS- 694-1990, 1100 Volts grade drawn through grey colour PVC conduits, medium grade, of suitable size conforming to IS-9537, fixed to surface of wall/ceiling etc with all accessories, fittings, fixures including 2.5 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

M & L for Sub main wiring with two runs of 4.0 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables conforming to IS- 694-1990, 1100 Volts grade drawn through grey colour PVC conduits, medium grade, of suitable size conforming to IS-9537, fixed to surface of wall/ceiling etc with all accessories, fittings, fixures including 4.0 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

Supply and Fixing exhaust fan, 300mm sweep metal body, AC single phase 230/240 Volt including bird free louver shutter cut to fit with hole for exhaust fan including providing holes grouting bolts and 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make : - Usha/almonard/Crompton/Khaitan/Bajaj. NOTE: - Quoted rate deemed to be inclusive of making hole in brick/stone wall by using core cutting machine for providing exhaust fan in wall including making good to match with existing and necessary fixing arrangement of louvre using nut, bolts, washers etc complete.

Supply and Fixing air circulating fan mounting on wall, 450mm sweep metal body, AC single phase 230/240 Volt including 3 core flexible copper conductor cable of size 24/0.20 sqmm, 5 Amps plug top complete all as directed. Make : - Usha/almonard/Crompton/Khaitan/Bajaj.

Material and labour for cutting existing 15 to 20 mm bore water supply pipe line in position/without taking down screwing & threading for alterations or additions including providing new union/Tee complete all as directed.

Supply, laying/fixing, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S&F 15 mm bore bib taps (bearing ISI marked) cast copper alloy with crutch or butterfly handle screwed down to iron pipe complete all as specified and directed. Make: CERA/ Hindware/Parryware/PRAYAG

S&F 15 mm bore stop valves (bearing ISI marked) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. Make: CERA Hindware/Parryware/PRAYAG

Supply and fixing 15 mm dia PVC connection 600mm long high pressure heavy duty braided type suitable for hot and cold water in geyser with 15mm dia brass union at both ends complete all as specified and directed by Engr-in-charge. Make: CERA/Hindware/Parryware/Prayag

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

S & F 50mm bore GI pipe "light grade" for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings, two coats of aluminium paint over a coat of zinc chromate primer complete all as specified

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, 4 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

PRACHANIVA CONSTRUCTIONS