Construction Work

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Upto 2m depth

Upto 2-3m depth

Upto 3-4m depth

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation and basement, etc with Crushed Stone sand (M-Sand) in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling in basement with Stone dust (Quarry dust) in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing two legged pipe scaffolding using 40mm first class M.S pipe including fixing cross bracing. EJP couplers for cross bracing and base plates including erection of scaffolding conveyance charges, loading and unloading charges and removing after completion of the work and taking away from the site et., as directed by the departmental officers

Providing and laying in position, Standardised Concrete Mix M-40 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 440 kg/m3 and maximum water cement ratio of 0.40, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation Basement

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality Fly ash bricks of size 23x11x7cm for foundation and basement including curing etc.,complete complying with standard specification.

Foundation and basement

Ground Floor

FIRST FLOOR

SECOND FLOOR

THIRD FLOOR

Fourth FLOOR

Fifth FLOOR

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below. (Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers. (The chemical should be got approved by Executive Engineer before use on work).

Plastering, Putty and Painting work

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying and applying of two coats of Ceiling Putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand prepared (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Flooring work

Flooring with Italian Marble Slab 20mm thick in required areas over a base layer of CM 1:3, 20mm thick with Epoxy grouting Cerabond 39 material and tiles matching with patterns, fixed to correct line, plumb, joints well cleaned, grouted with matching colour approved readymade grout, cured, etc. The marble slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete.

Supplying and laying of 8mm thick Woven Carpet of approved make with new one of fixing in position of thick Carpet including ( thorough scrapping of the existing floor and applying pattis to bring the floors smooth surface and fixing the unitex sheet with good adhesive fevicol of SR 998 and pressing the sheet in the floor to the standard including the wastage of unitex processed and conveyance to the site etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Paving the floor with best quality Double Charged Vitrified Tiles of size 1200x 600 x 10 mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete. (The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification).

Providing and laying of flooring with glazed full body vitrified tiles - glossy GVT tiles from Somany with any type of design texture such as marble finish, wooden, bamboo, stone finishes etc., scratch less, stain free and of size 1800 x 1200 mm and thickness between 19mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 12mm thick over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge including cost of overheads & contractors profit etc., complete for finished item of work. (APSS No.701 & 707) -

Paving the floor with best approved quality fine polished Ruby granite slab 1200mm x 600mm, 18mm to 20mm thick and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

CLADDING AND DADOOING WORK

Clading the walls by supplying and fixing of Italian Marble Slab 18-20mm thick in required areas over a base layer of CM 1:3, 20mm thick with Epoxy grouting Cerabond 39 material fixed to correct line,plumb,joints well cleaned, grouted with matching colour approved readymade grout, cured, etc. as directed and for fixing the marble slab in position wherever necessary. The quality and colour of marble slab should be got approved by the Executive Engineer before use on works

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge. Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works provided by Armstrong over the lowest and second aluminium section at an on centre distance of 600mm. Place the inside clip on the groove end of the panel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure.

Dadooing walls with double charged vitrified tiles of size 1200mm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. nbatly in all floors, curing, etc,,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works)

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Providing grooving to granite slab at the intermidate edges of the vertical face with neat finishing etc., complete with standard specification and as directed by the departmental officers . The cost including higher charges of machines and albour charges etc, complete.

Nosing to the granite slabs by cutting the granite slabs of 18mm to 20 mm thick edges and makeing semicircular shape to required size and nosing with semicircular shape and polishing using hand machine and the nosing with cirular shape and polishing with hand machine and the nosing is made highly smooth and gloosy, the cost includes labour charged and cost of machineries and polishing charges etc.,

Truss and Roof Sheet Work

Supply, Fabrication, Erection, alignment and levels as per approved shop drawing of structural steel work in built up sections comprising of ISMB, ISMC, angle, plates and round bar section,purlins, tie runners with sag rods, etc., Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, sand blasting, shop assembly, transport to erection site, storing, leading to erection site and apply a coat of anti-corrosive yellow primer paint of approved make and two coat of MRF enamel paint prior to erection t complete job in all respect. a) Connection Bolt are E350 GR.8.8 (IS3757) b) Hot Rolled are E350 GR, or Equivalent , Plate Grade E350 and all structural steel confirm to IS2062.c) Specification for Cold formed Light gauge Structural Steel Sections Confirm to IS: 811 d) Purlin but with Painted cold rolled steel sections Z Section MET- Z Purlin 250 X 60 x 2.5 e) Sag rod f) Painting confirm to IS 1477 part 1& 2.The rate is inclusive of design ,shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using cranes, labour charges for erection, cost of all materials involved and painting two coats over one coat of primer and as directed by the departmental officers.

Supplying and fixing of Continuous sandwich PUF panel 100mm thick either side singe piec,pre fabricated,moular,factory made units which consist of an insuating layer of rigid polyurethene foam between two layers of sheet of pre coated GI sheet of 0.50mm thick to produce straight to finishpanels withall necessary fixtures to complete the work in all repsect. The rate is inclusive of design,shop, drawing preparation,submissio for approval etc., and also inclusive of anyother incidential charges as such as lifting uisng cranes,labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supply and fixing of 2mm thk Aluminum Gutter with expansion joint at every 12.00m.,The rate is inclusive of design, shop, drawing preparation, submission for approval etc., and also inclusive of anyother incidential charges as such as lifting uisng cranes,labour charges for erection, cost of all materials involved and as directed by the departmental officers.

RAINWATER PIPE ARRANGEMENTS

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 6 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cost iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160mm dia

WATERPROOFING ARRANGEMENTS

Supplying and installing of not less than 1.5mm composite thick self-adhesive HDPE membrane, Dr.fixit Prebond S which is performed HDPE fully bonded membrane that bonds to the wet concrete cast on the membrane, having the following properties., 1. Puncture resistance of 1000N (as per ASTM E 154) 2. Tensile strength of HDPE without Adhesive (Film) of 25Mpa (as per ASTM D 412 Modified), 3. Elongation > 500% (as per ASTM D 412 Modified), 4. Peel Adhesion to concrete of 880N/m (as per ASTM D 903), 5.Dimesional stability of 0.50% (as per ASTM D 1204), 6.Hydrostatic head resistance not less than 60m head of water (ASTM D 5385-6), The size of Each membrane sheet on HDPE membrane Should be 2.40X20meter or 3 meter x 20 meter. This system should be fully bonded on the RCC and consists of higly resillent HDPE film, self-adhesive polymer layer and trafficable granular layer. The membrane shall have minimum of 75mm side and end laps which shall be sealed with double sided adhesive tape. All vertical surfaces will be fixed using prefixed gaskets/shot gun etc., complete complying with standard specification and as direct by the departmental officer.

Supply and applying water proofing treatment with membrane type water proofing methods using polymer modified bituminous membrane made using atactic poly propylene (APP) based with UV resistant, ground chemical resistant, high melting points, flexible and high adhesive strength. The membrane should have 4mm thick and 5.50 kg/sqm weight. The membrane shall be reinforced with non-woven polyester reinforcement of minimum 180 gm/sqm having tensile strength 850 N/ 5cm (L) and 575 N/ 5cm (T) including coating with compatible primer of bituminous base and torch application with overlap of 100mm wherever required. The membrane surface shall be protected with granules. The reinforcement provided shall be able to withstand the traffic flow density after construction and shall carry a minimum guarantee period of 10 years. The Rate inclusive cost of membrane, primer, and labour charges for laying by the loose torching on full surface or at overlap based onsite condition, including construction joint treatment and defective concrete surface treatment etc. complete complying with standard specification and as direct by the departmental officer.

Providing, mixing, laying polymer based water proofing treatment for the Sunken Toilet / Lift well / OHT Rcc wall by applying cement based, flexible, waterproofing compound confirming to IS:2645, to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specifications mentioned above providing cement mortar 1:3, waterproofing cover plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate quoted is inclusive of preparation of surface, which includes cleaning of surface polymer mortar curing, labour, tools and equipment, etc. Rate inclusive of grouting with cement and sand required for the treatment, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45cm for drip pipes, etc. complete.

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diameter - Depth per cm

100 mm dia

150 mm dia

200 mm dia

Packing the Toilet floor pipe corecutting for providing pipeline using Crystaline bonding agent which shall be applied as a bonding coat and non-shrink grout, after necessary surface grinding.

100 mm dia

150 mm dia

200 mm dia

Brick Jelly lime concrete 1:2:5 (one lime, two sand and five brick jelly) using 40mm gauge brick jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor finish, curing etc., complete complying with standard specifications (for flooring in toilet portions except water closet portions)

Laying of screed concrete using Cement concrete mix 1:2:4 ( one cement, two sand and four hard broken stone jelly) using HBGS 6-10mm ISS metal for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specification and as directed by the departmental officers

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Extra for vaccum dewatering in fresh concrete works 80 to 120mm thick by levelling with double framed screed vibrator finishing with power floatter and power trowel and indentical works etc., complete and as directed by the departmental officers.

Paving the top of roof with solar reflective ceramic tiles (required design) of 305x 305x 7mm thick of approved quality and colour laid in cement mortar 1:3 (One cement and three sand) 20mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint ,curing etc., complete complying with the standard specification and as directed by the departmental officers. (The make and brand of the tiles (Johnson endura or equivalent) should be got approved by the Executive Engineer before use on works)

Labour Charges for De-watering water using 10 HP Capacity desiel Engine pump set with necessary raw material such as supply of sucttion hose, deleviry hose uptom 100ft distance supply of diesel, supply of engine oil, labour charges for operating the engine and helper (Day& NightHours) for de watering the water from low level and building inne portion to outer main Drains etc., the rate inclusive of hire charges for diesel engine, cost of fuel, cost of engine oil. labour charges, hire charges for connection additional hose, conveyance charges for loading and unloading etc., complete as directed by the departmental officers.

FALSE CEILING ARRANGEMENTS

Supply and installationi of Anutone (or) Equivalent Brand of Acoustical False Ceiling of subtex ebony, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120Kgs/m3, weight 1.8/2.4/3 kg/m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angel with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 Main T wtih flange width 15mm, height 32mm and length 3600mm, , from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel ot the Main T15 to result in 600 x 600mm double. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance etc. complying to standard specification.

Supplying and fixing Gyp Board Suspended MR single layer false ceiling using 12.5 mm thick Gyp Board conforming to IS 2095 - 1982 fixing to Gyp steel GI perimeter channels of size 20 mm x 27 mm x 30 mm(web) of 0.5 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using Intermediate channels (45 mm x 15mm x 15mm x 0.9 mm) from soffit at 1220 mm c/c with ceiling angle (25 mm x 10 mm x 0.5 mm) fixed with GI Cleat and steel expansion fasteners & connecting clip to the ceiling channels (with knurled web of 51.5 mm x 26 mm x 10.5 mm x 0.5 mm) fixed in direction perpendicular to the intermediate channel at 457 mm c/c and fixing the 12.5 mm tapered edge Gypboard with 25 mm drywall screws at 230 mm c/c & jointing and finishing using joint compound and paper tape to have a flush look including filling the tapered & square edges with jointing compound, overheads and contractors profit, etc. complete for finished item of work as per USG KNAUF. PLAIN GYPSUM MOISTURE RESISTANT BOARD (USG / KNAUF)

Providing and fixing Green Pro Certified, Roll formed Linear 300C Slat Ceiling manufactured out of 0.7mm thick coil-coated Aluminium Alloy AA 3105. Perforated Aluminium Panel of 2 mm diameter diagonal patten with 5 mm centre to centre apertures represents 16 % openness with the Panel size is 300mm X 29 mm deep with panel lengths up to 6 meters, Coil Coated on a Continuous Paint Line, and shall be stove-enamelled in a continuous coil coating process with the white colour (RAL 9010) on the exposed side and the reverse side with polyester primer. The coated coil is passed thru ARKU SIX Hi configuration roller levelling process to ensure the flatness of the coil. Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3105 (Al. Mg) for higher strength and good roll forming characteristics. The panel shall be clipped to a baked enamelled aluminium carrier of 41.5mm wide x 62mm deep x 0.95 mm thick in standard length of 3 to 5 mtrs. made of double-baked stove enamelled aluminium magnesium alloy AA3XXX black with cut-outs to hold the panels. The Carrier shall be suspended by means of G.I. suspension rod 6mm in diameter, and a Galvanised suspension spring clip at a distance of 1.2 meters centre to centre. HUNTER DOUGLAS ALUMINIUM LINEAR PERFORATED CEILING (300mm x 29mm)

Providing & Fixing of Green Pro Certified AL - Lay-in Tile Plain False Ceiling on 15mm ‘T’ Framework of module 600mm x 600mm. Panels shall be manufactured by Hunter Douglas of size 584 mm x 584 mm made out 0.7 mm thick white colour (RAL 9010) coil coated on a continuous coil coating process on Aluminium Alloy 3105. a good corrosion resistance Luxalon Aluminium Tile ceiling system should meet the required standards for Green Product certification. The manufacturer should be ISO 9001:2015 Quality Management System Certification compliant with in house testing facility and should have their own registered manufacturing facility in India. HUNTER DOUGLAS LAY-IN ALUMINIUM WHITE FINISH PLAIN METAL TILE 600 X 600mm

Providing & fixing Cornice with gypboard 150mm wide of suitable design. The joints shall be finished with joint paper tape by using joining compound of India Gypboard ltd. The ceiling surface shall be painted with three coats of approved quality plastic emulsion over a coat of primer etc. complete as directed by the departmental officers.

HANDRAILS

Providing stainless Steel handrails with 10mm thick toughened glass with necessary fixtures. The rate include all labours, transport, scaffloding and other incidental charges in cluding all fittings etc. The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

DOORS

Providing and fixing of Dormakaba Operable Partition consisting of series of individual flat elements of 100 mm thick travelling along the ceiling track assembled to form a solid wall. The sound insulation of the operable partition should be 55dB tested under third party reputed laboratory in accordance to EN 20140-3. Elements must be constructed of a torsion-free steel horizontal tube frame and number of such frames should be based on the height of the walls and torsion-stiff vertical aluminium profiles, bolted together to make the element strong and sturdy. The frame must be claded either side with 16mm HDWR panels hung in acoustic free suspension from the panel frame. The elements must be inter-connected by means of a positive locking concave/convex aluminium profile with EPDM Gaskets and an integrated magnetic strip, having a linear attraction of 40N/m and polyurethane rubbers at four corners. Each element must have a spindle mechanism which should be connected to the spring loaded top and bottom retractable seal. The spindle mechanism should be operated manually by a bayonet connected crank handle that acts as a lock in function during cranking process. The horizontal top and bottom seals must be retracted as per the operating mechanism and should ensure a contact pressure of 800N at top and bottom when the seals are completely extended. The seal spindle mechanism must be accessible while the panel is hanging for servicing and adjustment if necessary. Total disassembly of the panel frame to access internal components is not acceptable. No fixed sweep seals allowed in top and bottom of the element that would rub against the track or floor while moving the element. The telescopic element or the end closure element must open and close 450mm horizontally. Each element must be suspended from the aluminium track on capable of withstanding a maximum load of 1000kgs per element.The trolley shall consist of Steel body with 4 wheeled roller bearings. Junctions used for Panels Turning shuold be of Steel Body. Rollers should be manufactured from Rust Proof Materials. Rollers should be unidirectional and self-guided. Track & Rollers should have interchangeable guides for smooth movement of panels to the desired parking slots.

Finishing the collapsable partition surface with veneer sheets of best variety and approved quality including necessary labour charges for laying through scrapping and polishing. The rate is including the GST of all materials such as veneer sheets, adhesives, polishing materials, hire charges for all tolls and plants, scaffolding arrangements etc. complete complying with standard specifications as directec by the departemental officers

Supply & Fixing of Door of Veneer finish Mikasa door of required size made of Hettich 316 grade with Best Ghana Teakwood Frame of Size 75mm X 125mm with flush Shutter of solid bond wood block board type with commercial ply on both faces 35 mm thick conforming to IS:2202 which is Laminated with Ghana Teak Veneer Lamination of 4mm thick with Pencil Grains conforming to IS 14315 on one side and 1mm PVC door cladding on the other side Including supply & fixing of Stainless Steel Hardware - 3 No.s Hinges - 9117214-BB4330 5 Knuckle - 2 Ball bearing butt hinges 4" x 3" x 3mm Grade SS 304 - Finish SSS, 1 Nos. SS Tower Bolt 300 mm long, 9121050 - 278 Dead Lock Type 2 Package, 6 Nos of 12mm Dia wedge anchors, including all Labour charges for wrought and put up and fixing in position, overheads and contractor's profit etc., complete for finished item of work.Door Handle of height 300mm with key hole located at 950mm from finished floor level.brass tower bolt on shutter inside. Rate to include architrave.

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1500mm x 2100mm with following specifications. A.Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b.Door leaf 1mm: Galvanized 120 GSM branded make JSW c.Shutter Thickness: 46mm d.Honeycomb: In-fill e.Glue Macroplast UR-7221 f.Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS304 - Finish SS g.Door Closer with Standard Arm Finish:Silver h.Lock Set: Dead Lock with both side key i.Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating : Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l.Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n.Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame 0.Rated Glass Schott Pyran with Frame p.Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, plastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.

Supplying, Erecting and Fixing Ornamental design Door made of as per the approved design. The above door consists of two openable doors with two leaves, openable doors altogether to a required size with frames similar to that openable doors in detailed below. the alround frame has been fixed with Teakwood planks of required size, outer border of frames should be fixed with Architrave, the door has been provided and finished with best melamine varnish finishing, scrapping the existing T.W panelled throughly on both sides of the door, sand papering without affecting the teakwood plank grooves and natural design with preparation of surface using sand paper and finishing the smooth wooden surface and applying of melamine polishing on the teakwood panelled door surface using spray machine on uniform layer of smooth surface formed without any air bubbles after finishing the work, Hydraulic Floor Springs (Heavy Duty) Double Acton Hydraulic Floor Spring of approved quality, brand, manufacture as per BIS Standards for doors including cost of cutting floors as required, embedding in to floors and stainless steel cover plates with aluminium pivot and single piece MS sheet outer box with side plate etc., with required raw materials, Brass tower bolt, Antique type ornamental design Brass handles etc. The rate should be inclusive of cost of all materials, labour charges for wrought and put up the doors with kadasal charges, labour for scrapping charges and transportion charges, etc complete complying with standard specification and as directed by the departmental officer (the materials quality are approved by the EE Before use of work.

Dormakaba automatic Sliding door operator ES 250 PRO Easy 6150 mm with low-noise drive motor without gearbox, TÜV design tested for 1.5 Million Cycle of opeartion in accordance with low voltage guidelines of IEC /EN 60335-2-103 and fulfils EN 16005 and DIN 18650-1 / DIN 18650-2 standards. With the clear passage width up to 3000 mm. The Profile Finish should be Silver Anodized E6/C0, with operator dimensions (H x D) : 100 x 180 mm. Drive with acoustically decoupled and exchangeable running rail and wear-resistant special surface. Rollers made of special plastic, Counter rollers as derailment protection.Mounting plate with prefabricated fixing holes and threaded holes. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time 0- 180 Sec, with smps, Class of protection IP 20.Program Switch with Knob, ES 250 PRO Easy, Maximum Panel Weight Carrying Capacity of 2X 125 Kgs & 1X 125 kgs each leaf. The Max. opening and closing force by the opeartor should not exceed 150N and maximum power consumption should not exceed 130W during opeartion mode.The operator should be equipped with EM failsafe lock with Nemo Combi sensor with 2x Microwave for activation and double rows of 24 spots failsafe Safety infrared curtains without the need of Photocell. The system shall have constant power supply 230V+ 5%, 50Hz, AC . Clear Opening 3000 * 4000 mm(W X H)-Weight of each panel up to 125kg . Operator will be fixed at a height of 3000mm and remaining 1000mm is supported with dormakaba 316 grade Rodan series spider fittings.The Spiders Shall be Manufactured my Investment casting process of grade SS316. The BHFB / BHAB bolts shall be of SS316 grade with all necessary accessories.A spring washer confirming to SS316 acts as a locking mechanism to secure nut in place ensuring full tightness for long period of time. Mounting Instruction: MS Post support required to fix the automatic door operator . Note : Minimum 2500mm distance required from one operator to another operator .

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and ioints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing M.S. Grills for doors, windows and ventilators of approved design and as directed by the departmental officers including cost of ms grills labour charges and cost of one of red oxide primer coat etc., complete complying with standard specification and as directed by the departmental officers.

Painting with Industrial Grade MRF epoxy paint works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing of Vertical Venetian windows fabric blinds with the following specifications Vanes:Vanes of 100 mm in fabric of approved colour and type with stainless steel vane carrier at the top of each vane. Each vanes have to be connected by small ball chain Railing Extruded aluminium powder coated in approved colours. External dimensions to be 44mm wide x 33mm high. Controls: The controls to be placed at right hand or left hand of rail as required. The minimum vane overlap in the closed position is 17mm. The vanes to be rotated to any position through 180 deg in both the directions. Cord and ball Chain Rotation or tilt of vanes to be controlled by an endless ball chain. The transverse of vanes to be controlled by a polyster braided cord attached to the leading traveller.

CUBICLES

Providing and fixing Greenlam Sturdo Classique Evergreen Toilet Cubicle( of Following standard dimension which includes 60mm door size width) made of heat,bacteria,water, chemical, Scratch,impaqct and anti bacterial resistant 12mm thick solid comapact laminate panels tested by SHriram Test House.Finish of the compact laminate should be Suede/*Raw Silk,which includes doors,plisters and intermediate panels finished with approved texture/ Shade as per the detailed drawings and as per IS2046 (Indian detailed drawings and as per fire resistant BS-476/97 Standard. The product should have Green Guard Certificate.This also includes providing and fixing inmposition necessary hardware made out of Staineless steel (Grade 304) as per manufacture's specifications and Architects instruction.like (1) Door Knob,(2) Gravity Hinges (3) Thumb turn lockset with occupancy indicators,(4) coat hooks with door stopper (5) U- Channels, (6) Adjustable foot/ Pedestal ,(7) Top rail with corner connector (8) Rubber noise deafening tapr, (9) SS Screws and wall plugs. The top fitting should consist of SS round top ral which will get fixed with plisters with SS panel tube holder, SS corner Bend(Connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the SS top rail. All screws woll of 304 Grade in Stainless steel with satin finish.All plisyers are supported by Stainless steel Bottom cladding will be anchored to the floor with a clearance height upto 1500mm and dircted by the departmental officers.

Providing & fixing Greenlam Sturdo Altura Urinal Privacy Dividers self-supporting 12mm thick compact laminates made out of, urea free, thermosetting phenolic resins treated Kraft papers as core material and Amino plastic resin treated decor papers on the finish surface, conforming to latest and applicable IS: 2046-1995, EN 438:2016 and NEMA LD3-2005 quality standards with Antivirus, Antibacterial and Antifungal properties (conforming to ISO 21702:2019, JIS Z2801:2010 and ASTM G21-2015 standards respectively) to fulfil the applicable requirements of indoor air quality certifications for Greenguard-Gold standards. This also includes providing and fixing in position necessary hardware made out of hardwares as per manufacturer’s specifications & Architects instructions like (1) L bracket (2) Screws & wall Plugs ( SS- 316 ). Available Design Options 1)-Dual Design Privacy Dividers : 12mm thick compact laminate size 450mm(D) x 1190mm(H), joined by using H profile ,Aluminium grade 6063-T6 in natural anodised finish. Fixed on wall with the help of SS grade 316 brackets. 2)-Minimal Touch Privacy Dividers: 12mm thick compact laminate size 450mm(D) x 1190mm(H), designed with slot for minimal wall touch for better hygiene . Fixed on wall with the help of SS grade 316 brackets.

ELEVATION GLAZING WORK

Providing and fixing Glass partition using 12mm thick toughened glass (Saint Gobain or equivalent make) to be fixed with SS Patch fittings at the site including filling of silicon sealent at all edges, gaps, wherever necessary as per the site conditon. The cost shall includes all the fittings, transportation, fixing, all labours, contigencies etc.,complying with standard specification and as directed by the departmental officers.

Providing and fixing of Wall Cladding (GFRC / Hunder Douglus Glass cladding/Equivalent superior brand) sided having required frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147 or equivalent in dust free conditions the gaps between to be filed with whether sealant and backer rod to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

R.O.WORKS

REVERSE OSMOSIS PLANT (RO) Supplying and erecting in position of 1000 Litres per Hours capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact

Supply and fixing of Automatic Multiport Valve 1” for Media Filters for the RO Plant DMF Backwash and Rinsing Applications etc, complete and as directed by the departmental officers.

Supply and fixing of Automatic Flushing Systems for Membrane in RO plant with LPS and microprocessor panel etc, complete and as directed by the departmental officers.

Supply and fixing of Dosing Systems – PH Booster alkaline water & Antiscalant, Dosing Pump – 2 No, Capacity 0 to 4 LPH , Make- PP- Head – 4 Kg/cm2- Accessories -Foot valve Dosing valve etc., Dosing Tank – 2 No, Capacity 30 Liters etc, complete and as directed by the departmental officers.

Supplying and fixing in position of Stainless steel RO product water storage tank of 1000 litres capacity suitable mounted on terrace with all inlet, outlet and drain arrngement and manhole at top of the tank including bottom supporting arrangement etc., complete and as directed by the department officers.

Supplying and fixing best quality and make of ready ,made PVC tank (Made of HDPE materials) of the following litres capacity as directed withh all accessories like cover locking arrangements etc., including conveying jointing delivery line scour pipe, over flow pipe etc and lifting the tank to the top of the building placed in position at the place as shown by the departmental officers etc., complying with standard specification

Supply & Fixing of Water Cooler for RO water drinking applications: ( Normal , Hot & Cold) Ro Product water from the RO Plant was stored in a water cooler. Auto cut off arrangements in a cooler helps to avoid over flow of RO water. Provision of Normal & Cooling water taps is available in the cooler. From the tap point’s normal & cooling water can be utilized for drinking applications. SPECIFICATIONS: Storage capacity(Liters) : 80, Nominal cooling Capacity(Liters/hr) : 20, No. of Faucets ( 1 Normal +1 Hot + 1 cold ) : 3 , Dimensions mm (W x D x H) : 660 x 575 x 1575 mm, Make : Blue Star

Internal and External Water Supply

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. External water supply

Below Ground Level

65 mm dia

50 mm dia

Above Ground Level

50 mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements. Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing PVC specials needs to be allowed

UPVC Elbow

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Tee

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Bend

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Coupler

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Hex Nipple

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Union

65 mm dia

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Reducer

65x50mm dia

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

20 x 15 mm dia

UPVC Reducer Elbow

65x50mm dia

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

20 x 15 mm dia

UPVC Reducer Tee

65x50mm dia

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

20 x 15 mm dia

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.Internal water supply

Above Ground Level

32 mm dia

25 mm dia

20 mm dia

Supplying CPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements. Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing PVC specials needs to be allowed

a. Elbow

32mm dia

25mm dia

20mm dia

32mm dia

25mm dia

20mm dia

c. Bend

25mm dia

20mm dia

15mm dia

d. Coupling

32mm dia

25mm dia

20mm dia

e. Union

32mm dia

25mm dia

20mm dia

f. Nipple

32mm dia

25mm dia

20mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

65mm dia

50 mm Dia

40 mm Dia

32 mm Dia

25 mm Dia

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia PVC Pipe

160mm dia PVC Pipe

250mm dia PVC Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Elbow

160mm dia

110mm dia

PVC Elbow with Door

160mm dia

110mm dia

PVC Tee

160mm dia

110mm dia

PVC Tee with Single Door

160mm dia

110mm dia

PVC Tee with Double Door

160mm dia

110mm dia

PVC Bend

160mm dia

110mm dia

160mm dia

110mm dia

PVC "Y" with Single Door

160mm dia

110mm dia

PVC "Y" with Double Door

160mm dia

110mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications.(The PVC cowl should be got approved by the Executive Engineer before use on works)

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

CLEAR SIZE 0.60X0.60x0.60

CLEAR SIZE 0.60X0.60x0.90

CLEAR SIZE 0.90X0.90x1.20

CLEAR SIZE 0.90X0.90x1.50

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

CLEAR SIZE 0.60X0.60

CLEAR SIZE 0.90X0.90

Supplying and fixing position Floor drain in polished chrome gratings of Jaquar/Kohler or approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The floor drain should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia Polished chrome Angle Valve (heavy duty) approved make of Jaquar / Kohler or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position White / Colour Glazed wall hung toilet with Pure clean bidet cleaning seat of approved make (jaquar / Kohler or equivalent) with CP bolts, nuts, CI chair, other hanging arrangemets, bakelite/ polypropiline seat cover with CP hinges, rubber buffer, CP brass screw, washer including all genuine accessories,Transportation and Labour charges for dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC should be got approved by the Executive Engineer before use on works)

Providing and fixing in position of Pneumatic or Mechanical tank 3/6L with Full frame approved make jaquar/Kohler or equivalent of concealed type In wall tanks with dual flow facility comprising of faceplates with buttons including all genuine accessories, brass/SS screws and washer,Transportation and Labour charges for dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The Wall tank should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia two way bib tap in polished chrome (heavy duty) with Health faucet metal hose in polished chrome of Jaquar/Kohler or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing White glazed Urinal Sensor DC with Urinal sensor with AC adaptor (AC+DC) with flusing adjustable in polished chrome of Jaquar / Kohler or equivalent type with one pair of Cast Iron concealed brackets, 32 mm dia bell mouth PVC connection and waste water Pipe with dome grating, 15 mm dia G.M. Wheel Valve, 15 mm dia "B" class G.I. Pipe, 15 mm dia nylon connection,15 mm dia brass Nipple,1 No. C.P. spreader, testing etc., complete as directed by the departmental officers.

Supplying and fixing in position best quality White / colour glazed Self rimming oval type wash hand basin of size 536x414mm with single faucet hole of approved make of Jaquar / Kohler or equivalent with a pair of cast iron brackets, including cost 15mm dia pillar tap in polished chrome, 32mm dia"B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Bottle Trap in Polished chrome (heavy duty) of Jaquar/Kohler or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Bottle trap should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Special type of mirror and frame approved quality of size 1000 x 780mm mirror fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing in position Towel ring in polished chrome of approved make (Jaquar / Kohler or Equivalent) with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The towel ring should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Tissue holder in polished chrome of approved make (Jaquar / Kohler or Equivalent) with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The Tissue holder should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Soap dish holder in polished chrome (jaquar / Kohler or equivalent) including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications.(The soap dish should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Step can in Stainless steel 6L capacity (jaquar / Kohler or equivalent) etc., complete complying with standard specifications.

Supplying and fixing in position Square toilet tissue holder with cover plate in polished chrome of approved make (Jaquar / Kohler or Equivalent ) with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The toilet holder should be got approved by Executive Engineer before use on works).

Borewell

Drilling of bore well any where in tamil nadu including transportation from one place to another place with in tamilnadu alluvial soil or sedimentary strata of clay and sand or sand, stone, shale, pevles, boulders etc,.By first taking pilolt bore of 140mm / 150mm dia and then enlargiing to required dia direct or reverse rotary mud circulation method using rotary rig, fuel, labour drilling, netonite mud and water required for drilling at the site ( site will be shown by the Officers) inclusing construction of mud pit.

Upto 60 m Depth ending below ground level

From 60 m upto 90 m Depth ending from ground level

From 90 m upto 120 m Depth ending from ground level

From 120 m upto 150 m Depth ending from ground level

From 150 m upto 180 m Depth ending from ground level

From 180 m upto 210 m Depth ending from ground level

Reaming from 140/150mm pilot bore to 300mm dia bore as directed by the departmental size bore as directed by the departmental officers upto following Depth ending from ground level..

Upto 60 m Depth ending below ground level

From 60 m upto 90 m Depth ending from ground level

From 90 m upto 120 m Depth ending from ground level

From 120 m upto 150 m Depth ending from ground level

From 150 m upto 180 m Depth ending from ground level

From 180 m upto 210 m Depth ending from ground level

Supplying unplasticised ribbed screwed PVC casing pipes without slot of pressure 6 KG/m2 in the drilled hole of the following dia 3 m length with screwed and socket ends and cantering ruide for every 15 m length of pipes as per ISI 12818/1992 including welding the joints supplying and pouting the annular space with pebbles of size and quality etc, complete

160mm dia plain PVC casing pipe Plain (cs)

160mm dia plain PVC casing pipe Slotted

Labour charges for insetring 150mm dia PVC.Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with the PVC Coupler with cement paste etc,.complete.

Supplying and Fixing of R.C.C hume pipe 300mm dia and wall thickness of 50mm and laying in proper position complete complying with standard specification and as directed by the Departmental officers.

Charges for developing the bore well with air compressor of capacity 600cfm/150PSI for a minimum 8 hours until clear water is obtained including transportation charges for air compressors etc., complete

Supplying of best and approved quality of HDPE 63 mm dia pipe of the following size including laying in the borewell and tying with copper wire etc., complete complying with standard specification

Supplying and fixing of 20mm dia Nylon rope for submersible motor of approved quality in etc,complete complying with standard specifications.

Supplying abd fixing of 160mm dia PVC end cap for bore well

Supplying and fixing of 5 H.P submergible Pump set of approved brand etc complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of 3 Phase Panel Board including labour charges of approved brand etc complete complying with standard specification and as directed by the departmental officers.

Supplying fixing and connecting of 4 core 6 sqmm 1.1 KV grade armoured aluminium conductor cross linked poly ethylene insulated pvc sheathed cables conforming to IS 7098 (part I) /1988 and as amended thereafter with ISI marking etc., complete complying with standard specifications and as directed by the departmental officers.

FIRE FIGHTING ARRANGEMENTS

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm nominal dia

100mm nominal dia

80mm nominal dia

50mm nominal dia

40mm nominal dia

25mm nominal dia

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply and fixing in position of Fire Fighting Duct Window having proper glass window type double door with universe open key, painted inside white and outsid post office red for the sizes of 1300 x 900 x 500mm (L x B x D) fabricated using 25 x 3mm MS 'L' Angle and all sides covered with 2mm thick MS sheets, suitable arrangements to kept 2 Nos. of Fire Fighting Hoses and 1 No. Branch Pipe, mounted in fire duct using anchor fasteners, etc., as per standard specifications and as per directed by the Departmental Officers.

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Wrapping and Coating Anti-Corrosive Treatment for under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers 150mm

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.100mm

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

FIRE EXTINGUISHERS

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

NON SCHUDULE ITEM & RATE

Supply & Installation of Gun Metal Ball Valve of size 25mm dia size including necessary Fittings

Supply & installation of MS angle / Channel Support for above mentioned pipes with necessary Anchor fastner, U Clamp, Painting etc.,

Supply & Installation of in position the sign board of "EXIT " with arraow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End ).

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End( 5 points / Coil) Higher End (LIFT WELL)

Supply and fixing of 30W recess LED 2X2 feet and luminaire lumens not less than 3600 lumens with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 34W LED full glow light fitting with lumens not less than 3200 lumens with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 16W cylindrical suspended (White/Black colour) mounted LED luminaire: Extruded aluminium housing, toughened glass cover,electronic driver duly wired upto terminal block, Luminaire lumen of 2000lm with necessary connections.

Supply and fixing Round fitting 18 watts LED luminaire with special application luminaire shall be designed to provide undisrupted lighting for dusty and humid indoor car parking with necessary connections.

Supply and fixing of 115W LED highbay symmetric beam luminaire with housing made of die-cast aluminium with necessary connections

Supply and fixing of Mirror Light Fitting with Accessories

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED lamp with LED bulb

Supply and Fixing of 250 watts LED flood light fitting on AI frame work with necessary connections

Supply and Fixing of EXIT Lamp Fitting

supply and fixing of 120W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 1200mm (48") sweep BLDC fan High speed complete with 300 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall with louvers

Supply and fixing of 24" heavy duty wall Mounting Fan louvers

Supply and fixing of 450mm (18") sweep (heavy duty) AC exhaust fan complete without provision of holes in the wall

Design, supply, erection, testing and handing over of High Mast Structure Crompton /Havells/Bajaj/make or equivalent with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 20 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 6 Nos. of 500 W LED flood light luminaries complete head frame assembly, Pulley drive, stainless steel wire rope single/double drum self lubricating winch arrangement suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast.

a) Design and casting of suitable foundation with 1:2:4 mix RCC concrete with 30 cm projection above the ground level with 1 metre Width x 1 metre Length and 2 metre depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site - 1 Job b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitablefor 3 phase 415 V 50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch - 1 Set

c) Feeder pillar box comprising 0.90 m x 0.45m x 1,20m floor AI frame with 63 A TPN main switch 1 no , 63 A fuse unit 3 nos, 63 A power contactor with automatic timer arrangements and reversing starter for the 3 phase motor - 1 Set. d) Neon aviation obstruction light (Crompton/bajaj make - 1 No. f) Hot dip galvanized lightning arrestor - 1 No. g) 500W LED Flood light luminaries of specially Heavy type water poof Dust proof integral luminaries fitting provided with 500 Watts LED Light fitting with LED Bulb with drives, Alglas coated reflectors, with cable connection etc,.and with assembly complete complete as per standard specification. - 6 nos (For Truck Bay & Service Area)

Supply and erection of 9.5 Mtr Flood light type pole with Fusion bonded epoxy coating & Marine Grade coating with powder coating of desired colour for corrosion free protction used in sea shore areas( Make: K-Lite-Sport king /equivalent) to with stand wind velocity as per IS -875. The pole shall be erected on the foundation concrete with foundation bolt M31 x750 mm four numbers (4 Nos ) and suitable size door at the bottom with locking arrangements along with Suitable single arm bracket as per the drawing attached made of Special pipe with following pole specification.

Height of pole: 9500mm ;

The pole will have four number of (Three tier 60W) LED light (Make K-Lite /equivalent) suitable for internal roads and fixed , rigidly to prevent any turning movement of bracket due to wind with concreting with construction of masonary pedestal of suitable size with 11 metres of 1.5 sq.mm pvc insulated 3core copper wire with necessary connection. The junction box provided with one number four way terminal blocks with 01 No - 6A SP MCB with backlite sheet and standard type terminal with connection complete, testing and commisiioning as directed by the departmental officers

Supply and erection of 5 Mtr Single arm pole with Fusion bonded epoxy coating & Marine Grade coating with powder coating of desired colour for corrosion free protction used in sea shore areas( Make: K-Lite-Mayur /equivalent) to with stand wind velocity as per IS -875. The pole shall be erected on the foundation concrete with foundation bolt M31 x750 mm four numbers (4 Nos ) and suitable size door at the bottom with locking arrangements along with Suitable single arm bracket as per the drawing attached made of Special pipe with following pole specification.Height of pole: 5000mm The post will have one number of 50W LED street light (Make K-Lite /equivalent) suitable for internal roads and fixed , rigidly with 4 Nos bolts and nuts to prevent any turning movement of bracket due to wind with concreting with construction of masonary pedestal of suitable size with 8 metres of 1.5 sq.mm pvc insulated 3core copper wire with necessary connection. as directed by the departmental officers (For the Landscape Area)

Supply and erection of 3 Mtr Single arm pole with Fusion bonded epoxy coating & Marine Grade coating with powder coating of desired colour for corrosion free protction used in sea shore areas( Make: K-Lite-Mayur /equivalent) to with stand wind velocity as per IS -875. The pole shall be erected on the foundation concrete with foundation bolt M31 x750 mm four numbers (4 Nos ) and suitable size door at the bottom with locking arrangements along with Suitable single arm bracket as per the drawing attached made of Special pipe with following pole specification.Height of pole: 3000mm The post will have one number of 30W LED light (Make K-Lite /equivalent) suitable for garden area.The post is fixed rigidly with 4 Nos bolts and nuts to prevent any turning movement of bracket due to wind with concreting with construction of masonary pedestal of suitable size with 8 metres of 1.5 sq.mm pvc insulated 3core copper wire with necessary connection. as directed by the departmental officers (For the Landscape Area)

Supply and erection of Aesthetically designed decorative 2x 12 W wood bollard 200 x 170 x 600mm LED Bollard light fitting with non corrosive SS fasteners guarantee against corrosion,Safety class II Protection class IP 54 ( Make K-Lite duo jado /equivalent)

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no 6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End (for Lift well)

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (PDB& Lift DB)

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm.with the following in flush with wall with earth connection only.(63 Amps 4P MCB-1 No, 63 Amps4P,30mA RCCB/ELCB MCB Isolator-1 No 63 Amps DP MCB-3 Nos, 6 Amps to 32 Amps SP MCB- 12 Nos)

Supply and run of 2 of 1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire with painting of suitable colour

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire with painting of suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductorof 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continous earth wire connection of 4sq.mm copper wire with painting of suitable colour

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 6 sq mm copper wire with painting of suitable colour.

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 10 sq mm copper wire with painting of suitable colour.

Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 6sq.mm copper wire with painting of suitable colour

PASSENGER LIFTS

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over with safety certificate of 1 no 26 persons Passenger lift(Gearless Lift without Machine Room) as per the following specifications and duties. 1. Location: Convention Centre,Muttukkadu,Chengalpattu District, Chengalpattu. 2.No of lift: one no 3.Type of lift: passenger lift 4.Capacity of lift: 26 persons/1800 Kgs 5.Speed: 1m / sec 6.Type of drive: V3F drive with enhanced ride comfort and near zero level functions 7.No of floors: GF+2 Floor 8.Total travel: 12 mts approximately 9.Leveling accuracy: high level accuracy with smooth and jerk free stopping 10. Construction of CAR: No 3 hardened sheet high quality stainless steel car and hand rail granite flooring and Perspex false ceiling with LED light fitting 11. Position of machine: directly above the lift well. 12. No of landing service: One in each floor front side- 4 no’s 13. No. of car entrance: one in the front side only 14. Car entrance door: power operated automatic V3F drive center opening sliding SS door

15. Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings 16.Lift well Size : 2300 mm (wide)x 2990 mm (depth). 17.Lift pit depth:1600 mm 18. Car size: 1600 mm (width)x2400 mm (depth) x 2200 (Height) 19. Car clear opening: 1200 mm wide x 2000 mm height. 20.Lift machine room size: 2500mm(H) x 4300mm(D) 21. Power supply: 400 / 440 v three phase 50 Hz AC supply for power and 230 V 50 Hz single phase power supply for light. 22.Control: micro computer (micro processor):based simplex collective control with / without attendant 23. Car fittings: LED lighting with 2 nos 300 mm sweep cabin fan. 24. Lift well: RCC construction with brick masonry existing. 25. Induction: UP / DOWN digital 26.Emergency alarm bell: battery operated bell to be provided with automatic charging device

27.Emergency light: battery operated light to be provided with automatic charging device 28.Fire mans switch: to be provided at the GF 29. Minor builder works: to be provided by the lift contractor. 30. Scaffoldings: to be provided by the lift contractor. 31. Sill angles and facia plates: SS to be provided by the lift contractor. 32. Steel for lift machinery: to be provided by the lift contractor. 33. Servicing and maintenance: free comprehensive servicing and maintenance for one year Guarantee period to be provided by the lift contractor. 34. Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories.

35. Provision for intercom with phone: to be provided by the lift contractor. 36.Lift license: preparation of drawings payment of charges to CEIG and insurance policy and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor 37. Floor position announcer: to be provided by the lift contractor.38.Special features a) Infra red door sensor with full height screen b) Full width half height rear panel mirror c)Tubular SS hand rail in car d) Stainless steel signal features e) Vandal proof SS button with SS cover f) SS door frames for landing doors g) V3F door operator h) Call register signal i) Stainless steel facia plates for car operating panel and landing fixtures j) Steel ladder for lift machine room k) On / off switch for fan and light l) Over load warning indicator with audio announcer m)Voltage stabilizer for control circuits

n)Braille button o) Pit ladder and Balustrade assembly 39.Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries 40. Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department 42. Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year.

SERVICE LIFT

Supply and Laying of 3 1/2 X 300 sqmm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 3 1/2 X 300 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 300 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 300 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 X 185 sqmm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good .

Supply and clarnping of 3 1/2 X 185 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clarnping of 3 1/2 X 120 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clarnping of 3 1/2 X 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clarnping of 3 1/2 X 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 4 x 25 sqmm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clarnping of 4 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 4 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 4 x 25 sqmm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete .

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and providing cable end termination of 4 x 10 sqmm . PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. .

Supply, erection of 300 mm Width X 75mm Height X 3mm Thick GI ladder type cable rack system made out of sheet steel folded to required shape with adequate number of supports.

Supply, erection of 600 mm.width X 75mm Height X 3mm Thick. GI ladder type cable rack system made out of sheet steel folded to required shape with adequate number of supports. .

Supply and erection of M.S. Material for ladder type cable trays, cable supports, SB, DB's supports, iron embeded in the wall, steel structure in open Area painted with two coats of primer and two coats of enamel paint. Substation to main panel room , ahu room and lighting conduit trays and suspensions of lighting conduit

250A Power panel- Design, Supply, erection, testing and commissioning of 250A floor mounted cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4 Nos. of 1” X ¼ ” tinned copper bus bar for 3 phases and neutral (25mm x 6mm) and 2Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creepage distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming: 1)Supply and fixing of 1 No. 250A 4 pole 433V LT MCCB confirming

to IS with Thermal Magnetic Release making capacity of 25 KA breaking for easy maintenance as per CEIG, IEconnection and terminations as required in specification. Outgoing: 1) S & F of 160A 3 Pole MCCB—4 Nos 2)S & F of 63A 3 Pole MCCB—2Nos Inter connecting the all LT MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve colour coding of phases and neutral indication. Double Earth connection of the MCCB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets of supply and fixing Electronic Multifunction Meter class 0.2S flush mounting L&T or equivalent make.Supply and fixing of danger board withSiemens grey powder coating with superScribing the names of places to which supply is fed feeder izes of cables direction of cables etc. rection of panel board complete with suitable oundation bolts and nuts including uitable M.S Channel, concreting, testingand commissioning L&T,C&S,SIEMENS,ABB) equivalent make.

160A Power panel- Design, Supply, erection, testing and commissioning of160A floor mounted cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4 Nos. of 1” X ¼ ” tinned copper bus bar for 3 phases and neutral (25mm x 6mm) and 2Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creepage distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming:1)Supply and fixing of 1 No. 160A 4 pole 433V LT MCCB confirming

to IS with Thermal Magnetic Release making capacity of 25 KA breaking for easy maintenance as per CEIG, IEconnection and terminations as required in specification. Outgoing: 1) S & F of 125A 3 Pole MCCB—1No 2)S & F of 63A 3 Pole MCCB—5Nos Inter connecting the all LT MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve colour coding of phases and neutral indication. Double Earth connection of the MCCB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets of supply and fixing Electronic Multifunction Meter class 0.2S flush mounting L&T or equivalent make.Supply and fixing of danger board withSiemens grey powder coating with superScribing the names of places to which supply is fed feeder izes of cables direction of cables etc. rection of panel board complete with suitable oundation bolts and nuts including uitable M.S Channel, concreting, testingand commissioning L&T,C&S,SIEMENS,ABB) equivalent make.

250 Amps Feeder Panel:- Design, Supply, erection, testing and commissioning of 250A floor mounted cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4 Nos. of 1” X ¼ ” tinned copper bus bar for 3 phases and neutral (25mm x 6mm) and 2Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creepage distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming: 1)Supply and fixing of 1 No. 250A 4 pole 433V LT MCCB confirming to IS with Thermal Magnetic Release making capacity of 25 KA breaking for easy maintenance as per CEIG, IEconnection and terminations as required in specification.

Outgoing: 1) 63 A 4 Pole MCB—12 Nos 2) 63 A 4 Pole Terminal block —12 Nos Inter connecting the all LT MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve colour coding of phases and neutral indication. Double Earth connection of the MCCB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with ,Supply and fixing of danger board withSiemens grey powder coating with superScribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable oundation bolts and nuts including uitable M.S Channel, concreting, testingand commissioning L&T,C&S,SIEMENS,ABB) equivalent make.

Bus Bar Chamber:- Supply and Fixing of 400A Wall Mounted Busbar Chamber with 400A TP MCCB Switch as Main Switch with necessary interconnection etc

Supply and erection and commissioning of outdoor type pillar box with angle iron supports and with double door & made of 16 gauge MS sheet of size locking arrangements finished with anti-corrosive treatment and painting with indication lamp with weather proof ventilation arrangements mounted on suitable concrete pedestal with cable entry holes to accommodate the control gears, cubical type modular type panel in sheet heavy gauge complete with 2 coats of enamel paint with two independent compartments with sealing provision to accommodate 4 way vertical type MCB DB, etc.and With Supply and fixing of Three phase Vertical type 4way MCB distribution board with Metal Door cover Code IP42 Protection , with 125A 4 pole MCCB as incoming and 4 No 63A TP MCBs as Outgoing on existing Pillar box with interconnection by copper cable, entry boxes with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Hager/Legrand make)

Supply, fixing, testing and commissioning of 10 kVA 3 phase UPS (Three phase input and Single Phase output ) with batterys and all necessary interconnection with system backup of 1 hour.

Earthing as per ISI standard with an Earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40 mm complete withearth plate of size 125 mm x 50 mm x 6 mm with necessary funnelling and masonry work with 38 mm RCC cover Slab for the brick mansonry

Supply and run of 1 of No.8 SWG Copper wire for earth connection

FAÇADE LIGHTING

Supply ,fixing and testing of exterior rated Architectural LED RGB flood lighting luminaire; suitable for facade lighting with Die-cast aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness, Total System wattage not exceeding 130 W with system lumen output should be more than 5400 lm with all LEDs on. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control with necessary connections

Supply ,fixing and testing of DMX Controller for the system including all other accessories required for the running of the system Controller should have Input Power 5-5.5V DC 0.6A and Output Protocol DMX512 with 4 universe, 2 universe should work in Stand Alone Mode and 2 universe should work in live mode with laptop/ tablet / computer. The universe should be expandable from 2 to 4 DMX512 universes. It should be compatible for Programmability with PC.

Supply ,fixing and testing of DMX address writer to write automatically address of DMX fixtures.

Supply ,fixing and testing of DMX Splitter with Input Voltage range : 190-240V AC, Power Consumption 5W max. Housing is made of CRCA with powder coated finish Mounting, 19 inch rack mountable, Operation Temperature -30°C to +55°C, 8 Output with 3pin XLR terminal sockets, Ingress Protection Rating IP20. This unit takes the DMX Signal from DMX Controller & split the signal into 8 separate output channels. The output terminals of Splitters are optically isolated from the input. Splitters should be capable to amplify the DMX signal & allowing the data link to be extended by max. 300 m (1044 ft.) using AWG 22 DMX cable or 150 m (500 ft.) using AWG 24 DMX cable or maximum 20-25 fixture per output channel. To be provided with IP enclosure if installed in external environment.

Supply ,fixing and testing of DMX Signal Amplifier to boost the Signal, IP 65 rated module to enahce the depleting DMX Signals, should have IP 66/67 rates inbuilt connectors compatible with Luminaires. It should be offered with inbuilt electronic ciruit for functioning. No external LED driver needed.

Supply ,fixing and testing of surface mounted, exterior-rated LED linearstrip light with 12W / Mtr ,5m roll with 480lm/mluminaire with all the necessary accesories as below that is designed for grazing architectural lighting applications waterproof and anti-dust LED strips. IP65, sealed with anti-UV silicon tube with slot for PCB fixation. CRI80 for better vivid color rendering SDCM<5, Robust Design & IP68 rating for outdoor use, with DMX control interface. Luminaire has input voltage range of 220-240 VAC, 50/60Hz, THD<20%, operating temperature -40°C to 50°C, IP68 & IK06 protection, Lumen maintenance of 20,000 hrs @ L50 at 35°C with 3 years warranty.

Supply ,fixing and testing of Aluminium profile with diffuer and necessary accessories.

Supply,fixing and testingof IP65 and above rated 150W/24V Driver

FIRE ALARM

Supply and installation of 2 loop analogue addressable fire alarm panel, 2 x 40 character backlit LCD, 2 independent sounder circuits, Sound Alarms, Silence/Resound,Mute Buzzer, Accept, Reset buttons, 12 button alpha numeric key pad and 4 cursor keys, Fire, Fault, Test, Disablement, Delayed Mode, Alarms Silenced, Buzzer Muted, Sounders Disabled, Relays Disabled, Power, Supply Fault, CPU Fault, Sounder Fault and Earth Fault indicators, inbuilt battery charger with 2 x 7 AH 12 volts battery.

Supply and installation of addressable smoke detector photoelectric type with base, LED to operate on 24 v dc supply.

Supply and installation of addressable electronic sounders cum strobe wall mounting type.

Supply and Installation of Addressable manual call points press type.

Supply & installation of addressable input/output control module interface units

Supply and installation of 2 core x 1.5 sqmm copper Armoured cable fixed on wall or ceiling with clamps, screw.

Supply & installation of MS junction boxes 4x4x2 inches suitable for mounting smoke detectors

Supply and installation of Beam Detectors for high ceiling area with capability of 100 metres distance. Consisting of transmitter and receiver unit with glass reflectors. To work on 24 volts DC supply

Supply and Installation of 950 W line Array passive Speaker Configuration 2x 6.5” (1.5 VC) LF 2 x 1.4” (2.5” VC) HF Frequency Response 80 Hz - 18kHz +3dB,SPL 129 dB SPL @ Coverage Angle @ 110° H x 12° V , wooden enclosure.Dimensions (WxHxD) mm 583 x 244 x 481. Make: Axiom/ L Acoustics /Proel

Supply and Installation of Corrosion free vertical quick release pin from OEM. Make: L Acoustics/Axiom/Proel

Supply and Installation of Corrosion free Horizontal Rigging fly bar kit for speaker & subwoofer from OEM. Make: L Acoustics/Axiom/Proel

Supply and Installation of 900+900 W, dual 15” Manifolded passive fylable Subwoofer, Configuration 2 x 15” (3” VC), Frequency Response 39 Hz - 120 Hz, SPL 139 dB,, Dimensions (WxHxD) mm : 571 x 800 x 582, Net Weight 65 kg,enclosure 15 mm phenolic birch plywood. Make: Axiom/ L Acoustics/ Proel

Supply and Installation of stage Monitor 12 Inches, Active coaxial 2 Way bi-ampable Element . The speaker cabinet must have frequency range of 70Hz-18kHz(+/ -3dB), sensitivity (1W/1m) 129 dB SPL @1m or more, power handling 1200 W class D Amplifier, Coverage angle 80 Degree Horizondal and 80 Degree vertical , Dimension 507mm(W) X 316mm(H) X 403mm (D) , weight max 16Kgs, contain 2) XLR/TRS Combo 3.5mm Input, and (1) XLR link Output. 15mm Phenolic birch plywood, Black textured paint and POWERCON main 4 pole for signal and power. Make: L Acoustics/Axiom/Proel

Supply and Installation of Master Amplifier ,Digital sound processor, In and Out Main sharebased digital signal processor ,RTA, SPLM, PRONET remote control,power capacity of 2 x 3000 W stereo amplifier rack.,Class H ,stereo power Amplifier with In built DSP ,Class one Complete with FIR Filters, Audio Limiters, Output delay per channel, GEQ per channel, PEQ per channel, Load impedance and having PC remote control option . Make: L Acoustics/Axiom/Proel

Supply and Installation of Digital signal processor, 2 In and 6 Out, 40 bit floating point resolution CORE DSP, 24 bit AD/DA converter, 110dB dynamic range, 5 bands of parametric equilizer on each in and out , 28 bands graphic equilizer, Limiter/compressor, upto 600ms delaytime on each input and output, Grouping function,SPL management.. Make: Moose /Axiom/Proel

Supply and Installation of 32 channel XLR input audio Digital mixing console 4stereo input, dual stereo master output, 4 Subgroup, 4Aux Output, USB input, sonarlee Audio software output, for record and edit with 100mm fader audio mixing console with independent 48Volt phantom power supply with display. Make: Behringer/Midas/ soundcraft

Supply and Installation of 24 Input / 8 Output IDR stage receiver and transmitter for audio and RJ45 network.Make: Behringer/Midas/ soundcraft

Supply and Installation of Wireless Dynamic handheld microphone Inbuilt transmitter ,Transparent 32 bit digital audio, 120dB dynamic,388 channelband, tansmitter and receiver over IR scan and sync, tuning band width compatible Designed to be used with most of acoustic vocal mounts for different acoustic application Back dynamic , Polar Pattern Cardioid , Frequency Response 20 - 20000 Hz Sensitivity -45 dB Max Spl for 1% THD 130 dB S/N Ratio 70 dB Impedance 2000 ±30% Power Requirement 12-18 V DC and ACV Power Cable and accessories. Make: Eikon/ Powerdynamic/Rode

Supply and Installation of Wireless collar microphone UHF Wireless Lapel Microphone with Receiver Transparent 32 bit digital audio,120dB dynamic,388 channelband, tansmitter and receiver over IR scan and sync, tuning band width compatible Designed to be used with most of acoustic vocal mounts for different acoustic application Back dynamic , Polar Pattern Cardioid , Frequency Response 20 - 20000 Hz Sensitivity -45 dB Max Spl for 1% THD 130 dB S/N Ratio 70 dB Impedance 2000 ±30% Power Requirement 12-18 V DC and ACV Power Cable and accessories. Make: Eikon/ Powerdynamic/Rode

Supply and Installation of 600 mm long condenser gooseneck microphone with base and light ring, Sensitivity: -40dB ± 2dB / 100Ω ±30%, Frequency response: 40Hz-20kHz (-3dB), Power supply Phantom 48Vdc Batteries 3V (2x AA),Switch: ON-OFF, XLR Connector. Make: Eikon/ Powerdynamic/Rode

Supply and Installation of Dynamic Neodynamium Super Cardiod Professional wired microphone Neodynamic Dual Coil Capsule Frequency response 50 to 19000hZ sensitivity-74 dbV , SPL @ 137dB load Impedence 600 ohms. Make: Eikon/ Powerdynamic/Rode

Supply and Installation of professional stereo headphone. Make: Eikon/Yamaha/Rode

Supply and Installation of 19 Inches Standard 36U Height and 1000 mm Depth Audio Equipments Rack Internal Control Wring, L angle Support, Dummy IU Space for each and every Equipment front Acrylic Door, Rear M.S Door and Side Lowers MS Door for Both Side and Suitable for the above Equipments etc., Make;Valrack/Eq

Supply and Installation of 19 Inches Standard 12U Height and 1000 mm Depth Audio Equipments Rack Internal Control Wring, L angle Support, Dummy IU Space for each and every Equipment front Acrylic Door, Rear M.S Door and Side Lowers MS Door for Both Side and Suitable for the above Equipments etc., Make;Valrack/Eq

Supply and Installation of suspended vertical fixing bracket with robe & chain with accessories. Make: Custom/Eq

Supply and Installation of 2x 2.5 sqmm OFC Ultra-flexible conductors speaker cable in existing pipe. Make: Proel/ Powerdynamic/Scp

Supply and Installation of 2 core shiled OFC Professional balanced microphone cable 2x0,22mm2 with flexible overall jacket. Make: Proel/ Powerdynamic/Scp

Supply and Installation of 4 Pole speakon connectors. Make:Proel/ amphenol /Neutrix

Supply and Installation of gold plated 3 pin XLR Connectors. Make: Proel/ Amphenol/Neutric.

Supply and Installation of 25 mm PVC pipe and accessories. Make:Custom/Eq

Towards Charges for testing and commissioning of Audio video system, Tunning, Alligment of the above audio system in the 2 Nos Convention Halls including one year on site warranty for hardware and software upgradation.

GST at 18%

P and C Projects Private Limited (BID ID -1164664)

GMS Elegant Builders I Pvt Ltd (BID ID -1164043)

BNR INFRASTRUCTURE PROJECTS PVT LTD (BID ID -1162920)