PROVN OF BOUNDARY WALL AROUND CERTAIN BUILDINGS AND OTHER SANCTIONED WORK UNDER GE WEST MATHURA

Amount

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Dismantling posts or struts ( wood, steel or RCC) embedded in concrete, brick work etc, any section and any length including taking out embedded portion and making good disturbed ground complete all as specified and directed by Engineer-in-Charge. Note :- Dismantling of existing galvanised iron steel barbed wire / chain link fencing shall be measured and paid for separately.

Dismalting chain link fencing of any description fixed to any type of fencing posts complete all as specified and directed by Engineer-in-charge.

Excavation in trenches in soft/loose soil not exc. 1.5 M wide and not exc. 1.5 M deep and getting out including forming bottom to required level or slope for laying of cable, pipe and concrete bed or for manhole etc not exc. 10 Sqm on plan all as specified and directed by Engineer-in-Charge.

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation over areas exc 1.5m but not exc 3m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Surface excavation n exc 30cm deep and average 15cm deep and getting out in soft/loose soil all as specified and directed.

Returning, filling in soft/loose soil including spreading, leveling and watering well ramming in layers n.exc. 25cm all specified and directed.

Removing surplus soil to a distance exc 250m but n.exc. 500m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under- reamed piles and mass concrete complete all as specified and directed by Engineer-in -charge.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stone aggregate for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and other similar works complete all as specified and directed and directed.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stone aggregate as in chajjas etc complete all as specified and directed.

Formwork to sides of concrete foundations footings bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter for rough finished of flat surface complete all as specified and directed.

Formwork to sides of pillers, posts, struts, piers, columns and stanchions of square , rectangular or polygonal for rough finished surface of concrete complete all as specified and directed.

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. complete all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished of flat surface complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT MS bars of 5mm dia and upto 10mm dia as in stirrups and spacers cut to lengh bent to shape reqd incl cranking bending spirally for hooking for column and binding with MS annealed wire not less than 0.9mm dia complete all as specified and directed.

M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for Mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc complete all as specified and directed by Engineer-in-charge. Note :- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment.

M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface, finished even and fair without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid saperately.

M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on other than fair face of brick or concrete surface, finished even and fair without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid saperately.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed.

Supply only liquid water proofing compound of approved complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

S&F super heavy duty 5mm thick corrugated shape PVC walll linning with decorative any colour PVC sheet as per sample approved by GE, inclusive of solvent cement and fixing at site on PVC frame as per specifications and manufacturer instructions complete all as specifed complete all as specified and directed.

M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint on walls complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for PCC (1:4:8) type D-2, using 40mm graded stone aggregate in foundation, filing and mass concrete complete all as specified and directed.

M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof:- (a) Cleaning plastered roof surfaces and applying a coat of Oxidised bitumen based solvented primer @0.3 Kg/Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed. (b) M&L for APP modified polymeric waterproofing membrane 3mm thick with non woven polyster core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be seated by flame complete all as per manufacture instructions and as directed.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

S&F precast hydraulically pressed PCC tiles of size 25cm x 25cm x 20mm thick laid over and including screed bed 15mm thick in CM (1:4) set and jointed in neat cement slurry and pointed in CM (1:3) mixed with WPC of approved make in screed bed and pointing on roof complete height upto G+2 story bldg all as specified and directed.

M&L 75 mm thick Cement concrete type D-2, (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in sub base of floors, complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 30mm thick factory made solid PVC moulded door shutter with particle board core with 5mm thick PVC moulded sheet on the front face and 5 mm thick PVC plain colour sheet on back face complete all as specified and directed by Eng-in-charge.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F Aluminium handle cast type anodized 150 mm long complete all as specified and directed by Eng-in-charge.

S&F stainless steel butt hinges 100mm complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

Supply & fixing factory made ‘Z’ type section steel windows with side hung shutters including projecting type hinges with steel handles and peg stay without glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply & fixing factory made ‘Z’ type section steel windows with side hung shutters including projecting type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item.

S&F 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified.

S&F Stainless steel gratings 100mm bore size fixed with white cement complete all as specified and directed.

S&F CP angle cock fancy type chromium plated 15 mm bore screwed down, high pressure screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 630x450mm including waste pipe and brackets but excluding tapes, chain and plug etc complete all as specified and directed by Eng-in-charge.

S&F 15mm bore CP pillar taps, swan neck, fancy type, cast copper alloy (minimum weight 350 gm) along screwed down high pressure with lettered hot & cold with long screwed shanks and fly nuts screwed for GI pipe complete all as specified and directed.

S&F PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and directed.

S&F vitreous china wash down, water closet pan (pedestal pattern), white including fixing bolts and connection to flush pipe and drain out going pipe and closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, CP jet including PVC connection complete all as specified and directed.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and32mm dia PVC flush pipe complete including jointing to socket of flushing rim, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge.

M&L for cutting chases, pining in making good to facing where required and pointed in CM (1:3) to ends or edges of brick wall etc and cutting chases for concealed conduit wiring etc and making good, match with existing surfaces by applying white/colour wash cutting not exc 10cm girth complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with solvent joints laid In trenches or fixed in floor / wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with solvent joints laid In trenches or fixed in floor / wall complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive complete all as specified and as directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed.

S&F 750 ltr capacity Rotational moulded polythene water storage tank white colour in triple layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F vitreous china urinal Half stall type, white incl CP spreader screwed for iron pipe and fixed complete including providing and fixing plugs with and including 60mm long brass screws, pointed around urinal back in cement, fixing discharge pipe, flush pipe, grating and union for discharge complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, coping, parapets and railing upto 60cm height, copings bed block,roof kerbs or mud stops, kerb stone, kneelers, apex stones, bed plates, surface channels and drains, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc. including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for salt glazed stone ware drain pipe 150mm grade 'A' laid in trenches and jointed in CM (1:1) complete all as specified and directed.

M&L for concrete bed to drain pipes 150mm dia including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, septic tanks, soakage wells etc. including placing in position and set in CM (1:6) complete all as specified & as directed by Engineer-in-charge. Note: - Reinforcement shall be measured and paid for separately.

M&L for Point wiring complete with 1.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 1.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

All as per item No 82.00 (here-in-before) but for one socket outlet 5 pin, 5amps on the independent board complete all as specified and directed.

M&L for point wiring with 2.5 sqmm PVC insulated, unsheathed FRLSH multistrand copper conductor cable 1100 volts grade drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all and including conduit fittings and fixing accessories 1.2mm thick sunken anodised pressed steel terminal boxes with 3.0 mm thick hylam sheet cover for mounting switches, socket etc including 2.5 Sqmm FRLSH multistrand copper conductor cable as continuous earth wire complete for one socket 16 Amp socket outlet controlled by one switch on independent board.complete all as specified and directed.

S&F socket out let, 3/6 pin suitable for 15 Amp plug top multipurpose 230 volt complete all as specified and directed.

S&F socket outlet flush type 5 pin suitable for 5 Amp 230 Volts all as specified and directed.

S&F switch Piano flush type 5 amp single pole one way 230 volts all as specified & directed.

S&F switch Piano flush type 15 amp single pole one way 230 volts all as specified & directed.

S&F ceiling rose of 65x50mm PVC/polycarbonate three terminal surface bakelite complete all as specifiend and directed.

S&F lamp holder insulated body with back plate batten/angle type for batten fittings complete all as specified and directed.

S&F LED bulb base B22 of capacity 10 watts not less than 700 lumens output at 6500K colour temp, complete all as specified and directed.

Supply & fixing tube light fitting with surface and wall mounted decorative ultra slim round profile LED lighting fixture, 20 watt LED with entruded polycarbonate, environment friendly, energy efficient ready to use with polycarbonate diffuser & integrated electronic driver complete all as specified and directed.

Supply & fixing MCB single pole 240 volt any rating from 6 to 32 amps, C series with rupturing capacity 10 KA complete all as specified and directed.

Supply & fixing MCB Single Pole Neutral 240 volt any rating from 32 amps, C series with rupturing capacity 10 KA complete all as specified and directed.

Supply & fixing sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply and fixing Geyser 25 ltr capacity in 5 Star rating, digital display, shock safe plug, incoloy glass coated element, feroglass technology, PUF insulation 0.8 Mpa high working pressure, Whirlflow technology, IPX-4 protection suitable for, 50 Hz, AC 240Volt, single phase supply, white blue with overall length approx 620 mm with wall mounting accessories & 02 Nos SS-304 connections 600 mm long complete all as specified and directed.

Supply & fixing security light with LED street light, 35 Watt, IP - 66, Impact resistance - IK07, colour temp- 5700 K, Class-I in pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & top opening for easy maintenance. Polyster powder coated grey after phosphochromate treatment High efficiency long life LED modules with SMD LED package mounted on MCPCB. Lumen efficacy of LED >110 lm/W with PC lens to ensure better uniformity of light distribution. Powered by Built-in, Potted electronic LED driver (SMPS based constant current supply) with lower THD, Output Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection upto 10 kV with external SPD & other safety tests as per IS 15885 Part-2/ Sec13 alongwith arm with single arm bracket OD 58 mm (max) with clamp, nut, bolts etc mounted on wall complete in all respect complete all as specified and directed.

Supply and fixing Exhaust fan metallic body of size 300 mm sweep, 50 Hz, AC 240Volt, 900 RPM, dynamically balanced impellers for smooth & vibration free operation, pre-lubricated double ball bearing for maintenance free running with aerodynamically designed & balanced blade, air delivery 1275 Cum/hr, noise level 40dB- 45dB and power consumption (50 W±10%) heavy duty single phase supply including mild steel louvers all as specified and directed.

M&L earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to arthing test point all as specified or indicated including testing on completion complete all as specified and directed.

S&F 20mm gun metal globe or gate valve conforming to IS : 778 ISI marked with iron wheel head screwed both ends for iron pipe including GI fitting socket, nipple, unions as well cutting of pipe and necessary earth work complete all as specified and directed.

M&L for dry sand (Tibba sand) and punning for cushioning to underground cable complete all as specified and directed by Engineer-in-charge Note: - For payment purpose thickness after punning shall be measured.

M&L for sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade of cross sectional area 16 sq mm 2 core confirming to IS-7098 (Part-I-1988) laid in trenches, along poles through pipes etc complete all as specified and directed by Engineer-in-charge. Notes :- (i) Excavation, earth work, sand cushioning, cable protection and GI pipe shall be measured & paid for separately under respective items of BOQ (ii) Road cutting / floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall deemed to be inclusive of the above provisions.

Ms Kamal Kant Agarwal (BID ID -3435570)

VANI CONSTRUCTION (BID ID -3440762)

B S ENTERPRISES (BID ID -3440844)

BHARDWAJ CONSTRUCTIONS (BID ID -3432178)

B R ENTERPRISES (BID ID -3435218)

ARCHI ENGINEERS (BID ID -3439796)

Deepak Saxena (BID ID -3435203)