PROVN OF CERTAIN WORK SERVICES FOR IMPROVEMENT OF SECURITY INFRASTRUCTURE AT AF STN BORJHAR

Amount

B/R PORTION

Dismantling structural steel work including doors, gates, but excluding framed truss etc. complete all as specified and directed.

Demolition of reinforced cement concrete in foundations, columns, beams and similar works complete all as specified and directed. (Note: The quoted rate inclusive of reinforcement cut as required to facilitate demolition)

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Removing mortar from bricks, cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish complete as specified and directed.

Dismantling of barbed wire on top of perimeter wall complete all as specified and directed. (Note: Each line wire to be measured.)

Dismantling of concertinacoil of any specification on top of perimeter wall complete all as specified and directed. (Note: Running length of the fencing/wall shall be measured as one unit for payment purpose.)

Surface dressing not exceeding 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in Soft/loose soil complete all as specified and as directed.

Excavation over area n. exc. 1.5 M depth for foundation etc. and getting out in soft/loose soil complete all as specified and as directed. (Note: During excavation work, no mechanical excavator is permitted at site, excavation through manually only.)

Excavation over area exc. 1.5 M and n. exc. 3.0 M depth for foundation etc. and getting out in soft/loose soil complete all as specified and as directed. (Note: During excavation work, no mechanical excavator is permitted at site, excavation through manually only.)

Excavation in trenches not. exc 1.5 m wide and not exceeding 1.5 m in depth for foundation etc drain, manhole, laying of cable not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed. (Note: During excavation work, no mechanical excavator is permitted at site, excavation through manually only.)

Excavation in trenches not. exc 1.5 m wide and exceeding 1.5 m but not exceeding 3.0 m in depth for foundation etc drain, manhole, laying of cable not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed. (Note: During excavation work, no mechanical excavator is permitted at site, excavation through manually only.)

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level, not exceeding 1.5 metre above the starting point complete all as specified and directed.

Removing excavated soil to a distance exceeding 250 m but not exceeding 500 m and depositing where directed at a level, not exceeding 1.5 metre above the starting point complete all as specified and directed.

Returning, filling in trenches including spreading leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil, complete, all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 (using 40mm graded stone aggregate) as in foundation, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 (using 40mm graded stone aggregate), cast in situ, in benching, coping and the like etc including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Material & Labour for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc, complete all as specified and directed.

Material & Labour for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in columns, pillers, piers,posts and struts etc complete all as specified and directed.

Material & Labour for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material & Labour for RCC M-30 (Design mix) (using 20 mm graded stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc, complete all as specified and directed.

Material & Labour for RCC M-30 (Design mix) (using 20 mm graded stone aggregate) as in columns, pillers, piers,posts and struts etc complete all as specified and directed.

Material & Labour for RCC M-30 (Design mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m spa complete all as specified and directed.

Use and waste of steel form work to sides of concerte foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work complete all as specified and directed.

Use and waste of steel form work to sides of pillars, posts struts,piers,columns and stanchions, complete all as specified and directed.

Use and waste of steel form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping), complete all as specified and directed.

Use and waste of steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams fair finished surfaces of concrete etc complete all as specified and directed.

S&F mild steel TMT bar 10mm dia and over (Grade Fe-500D ) cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F mild steel TMT bar 6 to 8mm dia (Grade Fe-500D ) cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No. 32 here-in-before but 5mm dia and over upto and including 10mm dia (Grade Fe-500D or higher) in stirrups, spacers and binders etc.complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

All as per item No. 34 here-in-before but except bricks complete. (NOTE: Serviceable bricks obtained from demolition shall be re-used.)

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including one shop coat of zinc chromate primer paint including preparation of surface complete all as specified and directed.

S&F mild steel Tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs gutters, arches, etc king rods and straining bolts conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F mild steel framed work as in angle iron such as grills, grating, etc, with ends of bars shouldered and or reivated or forget into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk way railings, gates to shape as directed, drilling holes, notching for wire etc, and similar works conforming to Grade E-165 (Fe 290), complete, all as specified and directed.

S&F Fibre glass reinforced translucent corrugated/plain sheeting 2 mm thick with side lap fixed with coach screw 'L' /'J' type or cranked hooks and washer complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed of granite over and including 15 mm thick screed bed or bedding layer of mortar 1:4 complete all as specified and directed.

M&L for providing and laying factory made kerb stone of M-25 grade cement concrete in position to the required level line, curvature, jointed with CM 1:3 including making joints with are without grooves including making drainage, opening etc complete all as specified and directed.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed, with grey cement and pigment laid over & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator, complete all as specified and directed.

M&L for painting to new steel surface of any description not otherwise described over 10 mm width or girth with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Supply and installation of 4mm thick aluminium composite pannel (ACP) sheet cladding with forming tray on aluminium hollow tube complete all as specified and as directed. Note:- The ACP shall be 4 mm thick (AL-45) with 0.50mm thick aluminium coil in both sides and polythene sandwitched panel of 3.00mm thick. The size of ACP board 1220x2440mm or 1250x4880mm. The board is to be cut in proper size and fixed with cadmium screw with frame work. the frame work is to be done as per manufacturer instruction and cost of frame work is deemed to be included in the unit rate of ACP cladding.

M&L for bracket stainless steel chromium plated letters alphabet, Airforce sign, dash, bracket of size 15cm including fixing to ACP sheet complete all as specified and as directed.

M&L for provision of gypsum board of 9mm thick ceiling tiles size 595mm x 595mm for including aluminium anodised section of size, wall angle 30mm x 25mm x 2mm thick, main / cross tee-section 15mm x 15mm x 1.4mm and suspended with 2.18 mm thick GI wire of suitable length and including fixed & aluminium snap grid all as per clause 10.38.1 of SSR Part-I and as per manufacturer’s instructions, complete all as specified and directed.

S&F 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 'colour' having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws and bituminous washers as in roof complete all as specified and directed.

S&F aluminium, powder coated, frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F 5.5mm thick sheet glass, ordinary quality, coloured/tinted/silver finish and glazing with oil putty including rubber beading cleats etc in square n exc 0.5 sqm in each pane complete all as specified and directed.

M & L for powder coated aluminium door shutters,aluminium section weighing 0.55 kg/m (minimum thickness of powder coating 50 micron)including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. powder coating of any colour complete all as specified and directed. (Note : Sheet glass / panel board shall be measured and paid under respective item)

M&L for bringing approved earth as stipulated in 3.22.6 of SSR (Part-I) from outside MD land distance beyond 6.5 KM but not exc 10 KM and forming embankement including spreading in layers n. Exc. 25 cm thick, watering, ramming complete all as specified and as directed. Note:- (i) Payment shall be made for solid quantity arrived after consolidation. (ii) Before execution of this earth shall be tested/ checked for suitability to use. (iii) Mechenical earth compactor shall be used for compaction of earth in layer. (iii) Quoted rates shall be inclusive of all taxes and royalities.

M&L for rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne but n.exc 12 tonne including watering as necessary and consolidating to required level , gradient or camber filling the hollows and depressions with approved earth, complete all as specified and directed.

M&L for 150 mm soling (or sub base) with broken boulders or broken quarried stone, interstices filled, surface formed and rolled and consolidated to required gradient and camber completes all as specified and as directed.

Material & Labour for 100mm thick GSB (Granular sub-base) grade V as per Morth table 400-I of MORTH, IRC specification spreading in single layer, watering, ramming/rolling by tandem vibrator roller & transverse gradient and required camber for achive field compaction at least 98% of MDD (Maximum dry density ) determined using modified procter density determination method as per IS code and CBR (Min 20) as per MoRTH complete all as specified and as directed.

M&L for 150mm thick (Compacted thickness) Water Bound Macadam (WBM) (in two layers of 75mm each layers compacted seperatly) as per table 400-II MORTH, IRC specifation with cruched stone aggregate of specified grading, rolled & consolidated using 8 to 10 tonne capacity power road roller to required gradient and camber complete all as specified and as directed.

M&L for preparing unsurfaced water bound macadam surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt and applying evenly a priming/ tack coat with bituminous primer of grade VG-10 by cutback bitumen at 10 kg per 10 sq metre etc complete all as specified and directed.

M&L for providing premix Semi Dense Asphaltic Concrete (SDAC), 40mm consolidated thickness with 5.5% binder content (using paving Bitumen of grade VG-30) by weight of total mix, rolled and compacted using 8 to 10 tonne capacity power roller to required gradient and camber complete all as specified and as directed.

M & L for painting lines, dashes, arrows, letters etc on roads, pavements and the like exceeding 10 cm wide with water based road marking paint with adequate number coats, white are golden yellow including preparation of surfaces, complete, all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete all as specified and directed.

M & L for 80mm thick machine pressed precast concrete coloured, rubber moulded, designer ( reflecting type) interlocking paver blocks of M-40 Grade confirming to IS 15658-2006 of of shape and size as directed, laid over & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator, complete all as specified and directed.

S&F MS framed brackets or angles or tees with web and flange cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, n exc 10 kg each brackets, conforming to Fe 410 or Fe-310 complete all as specified and directed.

S&F MS framed work such as grills, grating etc., with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar work confirming to Fe-290, Grade E-165, complete all as specified and directed.

S&F MS Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F concertina coil (reinforced punched barbed tape single layer) fixed on Y shape angle over security wall complete all as specified and as directed. [NOTE: (i) Dia of concertina coil 600 mm / 610 mm dia. (ii) Nos of turns in concertina 50 to 53 turns. (iii) weight of each coil 9.5 to 10 kg. (iv) Coverage per coil 6RM. (v) Verntral core wire Made from high tensile spring steel core wire confirming to IS 4454 duly hot dipped galvanized bracket confirming to IS 2629) with dia 2.59mm (+/-) 0.05mm UTS 145 -160 kg per sqm, zinc coating 250-300 gms /sqm. (vi) Running length of the fencing/wall shall be measured for payment purpose.]

S&F galvanised two strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type standard rail straining bolts, including securing or tying at crossing with and provision of galvanised steel pin etc., complete all as specified and as directed. (Note: Each line wire to be measured.)

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall, cornices etc and applying two coat of 100% premium acrylic weather coat exterior emulsion (anti-fungal, 1st quality, smooth clasic) paint having VOC content less than 50 gm/litre, as per IS 15489:2004, of approved colour over and including a coat of exterior alkali resistant primer applied @ 0.90 litre/ 10 Sqm, complete all as specified and directed.

E/M PORTION

M&L for Point wiring with 1.5 Sqmm PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLSH type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.6mm thick, with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point or bell point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLSH type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metallic bodies of luminaires/ fan at other end complete as per site requirement and all as specified & directed by Engr-in-Charge for the following:- (a) One light / fan / bell point controlled by one number one way switch. (Note:- Unit rate include for cutting chases for conduits and sinking for boxes & making good to wall, floors etc.)

S&F switch piano flush button 5/6 Amp single pole one way 230 volts white finish all as specified & directed.

S&F for PVC/polycarbonate isolated body ceiling rose surface type bakelite 65x50mm three terminal including connection complete all as specified and as directed.

S & F LED light fittings, 4 feet, 40 watt, 220 volts,AC, decorative box type with driver including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S & F factory made sheet metal enclosure double door designed SPN 8 Way DB, IP 42 with 200 Amps rated copper busbar, grouter/ fixed flush in wall with and including suitable flat iron complete with, neutral link, dinrail suitable for mountaning MCB’s complete all as specified and as directed. (Note:- MCBs shall be measured and paid separately)

S&F MCB SPN 16-32 Amps, 230 Volts, 50 Hz with 10 KA, 'C' series complete all as specified and as directed.

S&F MCB, Single pole, 6-10 Amps, 230 Volts, 50 Hz with 10 KA, 'C' series complete all as specified and as directed.

S&F Air circulator metallic steel body, single phase, 230 V, 50 HZ of size 450 mm sweep, 1400 RPM, CFM 150 cum/hr heavy duty type with suitable metallic louver, blades, frame & flexible three core copper conductor cable of suitable for connecting with ceiling rose complete including fixing on post/wall complete all as specified and as directed.

Supply, fixing/ laying, testing, connecting and commissioning of LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) of size 70 Sqmm, 3.5 Core as per IS:7098 (Pt-I), with multistranded aluminium conductor, 1100 Volts grade laid in trenches/ on wall/ poles/ ducts/ inside protection pipe including cable glands, lugs and MS saddle clips of suitable size (where ever cable laid on ceilings / walls without cable duct) complete all as specified and as directed. (Note: Excavation & earth work, cable cover, sand cushioning shall be measured and paid seperately under respective items.)

All as per Srl Item No. 78.00 here-in-before but for 50 Sqmm 3.5 core complete.

All as per Srl Item No. 78.00 here-in-before but for 16 Sqmm 4 core complete.

Supply and spreading dry river sand in trenches for protection of underground electric cable, spread in uniform 23 cm thickness and punned down gently to 18 cm complete all as specified and as directed. (Note: Punned thickness shall be measured and paid.)

Supply and laying well burnt Sub Class 'B' locally available best quality laid in trenches perpendicular to UG cable above sand cushioning for cable protection complete all as specified and directed.

Supply and install steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP - 31 (9 metres long) conforms to IS & with and including GI brackets of 40 mm bore, light grade, 1.5 RM long for fixing street light luminaires, including applying two coats of black bituminous paint internally and externally upto planting depth and applying two coats of aluminium paint over a coat of red oxide primer, externally from top of coping complete all as specified and as directed. [Note :- (i) Excavation and earth work, PCC foundation and coping shall be measured and paid separately. (ii) The contractor should provide Test Certificate from the manufacturer against confirmation of IS 2713 (Part-1 to 3)-1980, IS 1161-1998, IS 2062 E250, IS 1367 Part 3, BS EN ISO 1461-1999 or Eqvt & BS EN 5135 or Equivalent. (iii) All welding works related to pole should be carried out at the factory premises of the manufacturers.]

S & F IP 66/ 67 thermo plastic-polycarbonate cable junction box of size 155X210X92 with terminal which is totally shock proof, water proof, halogen free, silica and having internally embedded gasket technology, complete all as specified and directed.

S&F LED street light luminaries with aesthetically designed IP-66, pressure die cast aluminium housing and toughned flat glass with wattage 70 W Rated CCT 5700K ± 5%, 230V, 50 Hz, power factor > 0.95, with surge protection 4 KV (internal) Inbuilt 10 KV external SPD, wall or surface mounting using adjustable MS cradle complete all as specified and directed.

S & F LED flood light 70 watt 230 V AC outdoor type aluminium alloy pressure die-casted housing control gear box for better heat dissipation and aesthetic appeal in multiple optics and equipped with IP 65 upto 4 KV (internal) surge protection, complete all as specifid and directed.

M&L for PVC insulated and PVC sheathed 1.5 sqmm 3 core copper flexible cable 1100 volt grade conforming to IS 694 for connection of street light fitting from junction box to light fitting complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600mx600mmx6 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to earthing test point and testing on completion complete all as specifed and directed. [NOTE : (a) Proper earthing pit should be provided with pit cover. (b) Excavation/earthwork is deemed to be included in the quoted rate. (c) In case of desired test result is not achieved, the earthing shall be redone with out any extra cost to the department.]

M&L for Earthing complete with GI earth plate elecrode of size 600 mm × 600 mm × 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to GI earth strip 25 mm x 4 mm by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work pre-cast RCC(1:2:4) type B-1 pit cover 50mm thick, reinforced with 8mm dia TMT bars @100 mm /C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab and PCC(1:2:4) type B-1 concrete pit and angle iron frame and opening arrangement) including providing charcoal or coke and common salt in alternate layer of 15 cm compacted thickness all around the earth electrode with funnel and 20 mm bore galvanized iron watering pipe (medium grade) wire mesh, copper lugs, complete in all respect, protected by 32 mm bore (light grade) GI pipe up to earthing test point as directed, connected to O/H continious earth wite on pole and testing on completion complete all as specifed and directed. [NOTE : (a) Proper earthing pit should be provided with pit cover. (b) Excavation/earthwork is deemed to be included in the quoted rate. (c) In case of desired test result is not achieved, the earthing shall be redone with out any extra cost to the department.]

S & F 80mm bore GI tubing, light grade, with all fittings, fixed on wall /pole through MS flat (25x3mm), nut, bolts & washers, complete all as specified and directed. Note: The quote rate shall be inclusive of MS Flat iron

S & F 80mm bore GI tubing, medium grade, with all fittings, laid in trenches, complete all as specified and directed.

S & F 50mm bore GI tubing, light grade, with all fittings, fixed on wall/pole through MS flat (25x3mm), nut, bolts & washers, complete all as specified and directed Note: The quote rate shall be inclusive of MS Flat iron.

S & F 50mm bore GI tubing, medium grade, with all fittings, laid in trenches, complete all as specified and directed.

M & L for horizontal boring under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine for passing GI protection pipe of 50 to 80 mm bore etc complete all as specified and directed. (Note: GI pipe shall be measured and paid seperately under respective items.)

NOTE: Schedule of cedit amount of Rs 13,26,200.00 shall be deducted from the total quoted amount of BOQ.

KAIZEN INDUSTRIES

M/S PRASANTA MAHANTA

M/s Bikash Enterprises