Construction of Slaughter House at Papparapalli ward No.10 in Sy.No.43/1 in Kayalpattinam Municipality

Amount

Earth work excavation in all classes of Soils and Sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering , bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the Departmental officerswith an initial lead of 10mts and initial lift of 2mts and clearing and levelling the site etc, complete complying with standard specification. ( TNSS NO or NBC No 23,24, V,VI S2)

2nd depth

Plinth Beam

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Cement Concrete of mix 1 : 4 : 8 (One Cement four sand eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification.

Supplying and filling of well gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification

Supplying , errecting and Centering for Side and Soffiots including necessary supports for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90x60cm & 10 gauge stiffened, welded with steel angle of size 25x25x3mm for boarding laid over silver oak joists (Country wood) of size 10x6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 -13cm dia.spaced @ 75cm c/c etc., complete complying with standard specifications for Pavement Drain etc., Complete.

Plane Surface

Column

Supplying and Fabrication of Steel and placing in position MS / Ribbed tor steel grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc., Complete complying with standard specification in force per Kilogram.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers -

Ground Floor

Brickwork in cement mortor 1 : 5 (One Cement and five Sand) using best quality of country bricks of size 83/4x41/4x23/4 including all cost of materials and Labour Charges including Curing charges etc., Complete as per standard specification.

Ground Floor upto 4.50mt

Special Ceiling Plastering in Cement Morter M. 1 : 3 (One cement, three sand) to 10 mm thick including all cost and conveyance of all materials to site including cost of cement which will be purchared locally by the contractor and conveyance of the same to the actual work site and cost form work including watering curing and all leads of good potable water and all other.

Weathering Coarse with concrete broken brick jelly concrete on 20mm. Gauge in pure slaked shell lime (no sand to be used) over roof slab be proportion of brick jelly to being 32 : 12.5, Well beaten with wooden beaters giving the required shape and thickness as directed by the Departmental Officers.

Finishing the Top with One Course of Machine Pressed Tiles of Size 200 x 200 x20 mm of Approved quality laid in cement mortor 1 : 3 (One part of cement and threepart of sand) mixed with water Proof Compounds 2% by weight of cement used and the top pointed with the same mortar etc., complete.

Supply and fixing of Polished Rajasthan kota stones 20mm thick with machine ctting edges for Flooring inculding laying Vibrating, curing and finishing bearing surface at the sides and bottom of the slan, beams of shall be finished smooth with cm 1:3 and craft paper laid without claiming extra cost complete complying with standard specification and as directed by the departmental officers

Paving the floor with descrgned coloured vitrified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three M- Sand) 20mm thick and pomted with same coloured cement neatly etc., complete.

Plastering in Cement Mortar 1 : 5 (one cement and five sand) to 12 mm thick including all cost and conveyance of all materials to site including cost of cement which will be purchared locally by the contractor and conveyance of the same to the actual work site and cost form work including watering curing and all leads of good potable water and all other.

Painting the walls with Two Coats weather Proof Exteriour Emulsion based emulsion Paint over one coat of primer as instructed by the departmrntal officers including Preparation of surface curing, etc complete in all floorscomplying with standard specification. ( The Colour and shade of the paint shall be got approved by the departmental officers.)

Supply and Fixing of Stailess Steel Doors with frame ( Box section using Stailess Steel frame of 1.6mm thick ), of size 100mm x 60mm with a rebate of 30 /35mm x 15mm on one side of the frame including supplying and fixing dovetil splayed Stailess Steel hold fast, cost of material and Labour including all incidental charges etc., complete complying with standard Specifications.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work

Supplying and Fixing of Push and Pull type Rolling Shutter confirming to IS 6248/1979 and as amended from time to time. With ISI make of approved size and section using 18 gauge G.I.sheet. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., and as directed by Engineer incharge.

Supplying and fixing in position of Iron grills of required size using 32 x 32 x 6mm angle around and 2 Nos of vertical at center with b flats diagonally to the existing open space for grills into necessary hold fast conveyance and one coat of primer etc., complete for Windows and others.

Painting the new iron works such as steel doors, Windows,Ventilators windows bars,balustrades etc, in all floor with two coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc, complete complying with Standard Specification. ( The Make, Quality and colour of paint should be got approved by the engineer in charge before use on works ) ( TNSS NO or NBC No 61 V VI (54) 3)

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supplying and Fixing in position best approved of BIS quality 110mm P.V.C Rain Water down fall pipe having a pressure of 4Kg / Sq.cm including cost of necessary PVC shoe,PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc, and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc, complete. The rate shall be inclusive of cast of removable cast iron grating. The PVc pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.00mt pipe length etc, Complete Complying with Standard Specifications.

Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC Unsheathed Cu. Conductor of 1100V grade in cuitable PVC rigid pipe concealed in wall and Ceiling with PVC accessoires in flush with wall with 3mm thick with TW Switch box and 5A F.T. Switch Inflush with wall coverd hylam sheet of 3mm thick with paiting of suitable colour for concealed P.V.C Light point / Fan Point (for Electronics Regulator) (PWD Elect.SOR SD.No.23)

Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC Unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and Ceiling with PVC accessoires in Flush with wall 150mm x 100mm x 113mm TW Switch box with 3mm thick Hylum sheet cover for 5A 3 pin non inter locking CS Plug with continuous earth wire connection of 14SWG TC wire and making good of the Concealed portion with suitable colour for CONCEALED PVC PLUG POINT (PWD Elect.SOR SD.No: 36)

Supply and run of 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in 25mm dia GI Pipe(Class B) suitably bent at both ends with necessary angle iron upright and end supports for mains mains(PWD Elect.SOR SD.No.69)

Supply and fixing of 16Amps DP switch with metal glad of 500V with fuse and nuetral ( side handle) on suitable TW box PWD earthing (PWD Elect.SOR SD.No.146)

Supply and Fixing of TNEB meter Board suitable for 32A Single Phase Service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper Flat) on TW Plank of Size 375mm x 300mm x 19mm with Supporting TW Reepers of 1" thick an either side with Painting with Suitable bolt and nuts for fixing the TW Plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB Meter to Fuse Unit (SD No :125)

Supply and run of 4 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V on 7/20 GI bearer wire for service connection mains (PWD ELECT SOR 24-25 SD-67)

SUPPLY AND DELIVERY OF 25 MM DIA G I PIPES TWAD SOR 24-25 Page No.27

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work SD 212

Supply and fixing of single box type 4'18W LED Fitting on wall or ceiling with LED light fitting with PVC unsheathed Copper leads from terminals to the fitting. (PWD SOR 2024-25 P.No.168)M-1274

Supply and fixing of 48W LED Street Light Fitting with LED Complete. (PWD SOR 2024-25, P.169)m-1291

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp (SD 107)

Conducting Geophysical survey, quality and quantity test and transportation charges etc, (This includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist)

Drilling 6" vertical bore in hard rock area to any required depth as directed by the board officers including labour charges for inserting casing pipes assembly in the directed hole including welding the joints if necessary grounding the casing pipes etc., and including transporting from one place to another etc., complete TWAD SOR-2024-25 P.g.No-197

Supply and delivery of PVC casing pipe of the 200mm dia pipes as per IS / 12818 / 92 and as amended from time to time to suit the borewell upto 150m depth (CM) with ISI marking including, loading, unloading , freight, stacking and transit insurance charges etc, complete. TWAD SOR 24-25 Page No.6

Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc.,complete. TWAD SOR 24-25 Page No.197

Supplying, laying and jointing G.I. Pipes of approved quality and best variety of "B" class pipe of the following dia including labour fixing G.I. Specials, including charges for cutting and threading of pipes, cost of such specials with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., etc., complete UPVC Pipe 32 mm TWAD SOR 24-25 Page No.7

50mm dia GI Pipe TWAD SOR 24-25 Page No.27

50mm dia GI Elbow TWAD SOR 24-25 Page No.32

50mm dia GI Flange TWAD SOR 24-25 Page No.32

63mm pvc bend TWAD SOR 24-25 Page No.10

63 mm pvc Elbow TWAD SOR 24-25 Page No.10

63 mm pvc pipe(6ksc) TWAD SOR 24-25 Page No.5

63 mm pvc Tee TWAD SOR 24-25 Page No.10

Supply and fixing of 50mm dia GM Gate Valve with ISI make, the cost shall including materials, fixing and labour charges etc,complete as per standard specification. TWAD SOR 24-25 Page No.33

Supply of 4 SQ.MM PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 TWAD SOR 24-25 Page No.124

Supply of 3 HP THREE PHASE 100 lpmx75m SUBMERSIBLE PUMPSET SUITABLE FOR 150MM DIA BOREWELL WITHOUT PANEL BOARD AS PER IS 8034/2002 TWAD SOR 24-25 Page No.104

Supply of 3 HP THREE PHASE PANEL BOARD- D.O.L. WITH TWO LEVEL GUARD . PANEL BOARD SHOULD BE PROVIDED AS PER SPECIFICATION TWAD SOR 24-25 Page No.119

Supply of 32 Amps TPN Metal clad switch with rewirable fuse units PWD SOR 24-25 Page No.173

Supply of 32 Amps Porcelain fuse unit (500 V) PWD SOR 24-25 Page No.175

Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx 4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc.,TWAD SOR 24-25 Page No.91

Supply and fixing 200mm dia PVC End cap as Bore cover on top for securing TWAD SOR 24-25 Page No.10

Supply and Erection of Nylon Rope PWD SOR 24-25. P -156

Labour charges for the erection of submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps, erection clamps, pressure gauges etc., complete and testing the pumpset and trail run for 10 days.TWAD SOR 24-25 Page No.204

Provision for HDPE Water Tank 2000 liter capacity TWAD SOR 24-25 Page No.87

Refilling with excavated earth in layers of 15cm thick including watering and ramming to consolidation etc complete

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 80mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with Stone Dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, Stone Dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Manufacturing, supply, fixing and commissioning of 5 KLD Capacity of Effluent Treatment Plant. 25mm MS Flat at 20mm spacing with handle for bar screen. 1 No. of CI non clog horizontal centrifugal effluent transfer pump having 1 cum / hour at 12m head capacity, 2 Nos. of CI non clog horizontal centrifugal sludge transfer pump having 1 cum / hour at 12m head capacity, 2 Nos. of HDPE tank having 50 litters capacity with 0 to 6 LPH at 0.3 kg/cm2 capacity of chemical dosing pump, 1 No. of roots, twin lobe 2.0 Hp motor having capacity of 30cum /hour at 0.3 Kg/cm2 for air blower motor, MS fabrication air distribution grid with valves, fittings and 24" size of polyurethane distribution hoses. 1 No. of MS Tank consist of aeration tank, secondary setling tank, filter feed tank. 2 Nos. of Monoblock centrifugal filter feed pump having 1 cum/hour at 20m head capacity with base plates and couplings. 1 No. of vertical, cylindrical type pressure sand filter having 3.0 Kg/cm2 working pressure and not less then 5.0Kg/cm2 design pressure with 1.0 m3/hour service flow rate. 1 No. of vertical, cylindrical type activated carbon filter having 3.0 Kg/cm2 working pressure and not less then 5.0Kg/cm2 design pressure with 1.0 m3/hour service flow rate. 1 No. of flow meter having capacity of 1.0 m3/hr. The rate including all material cost and all labour charges for erection and commissioning of ETP etc.,Complete as directed by departmental officers.

Construction of Bar Screen chamber having size of 0.50 x 0.50 x 1.0m base slab and side wall made with RCC. Effluent collection tank having size of 2.50 x 2.50 x 2.50m, base slab and side wall made with RCC. Sludge drying bed having size of 1.00 x 1.00 x 1.00m, made with Brick. Installation of MS packaged tank having size of 6.00m x 4.00m x 0.30. The rate including all material cost and all labour charges for erection and commissioning of ETP etc.,Complete as directed by departmental officers.

SHEIK ABDUL KADER (BID ID -1334178)