Construction of ITI Bus Stand at Ranchi Jharkhand

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above groundlevel), including cutting of trunks and branches, removing the roots andstacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth

DISMANTLING WORK

Dismantling pucca brick or lime work including stacking servieable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all comlete as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads all complete ap per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M. Lead and disposal of unserviceable materials with all leads all complete ap per direction of E/I.

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

EARTH WORK

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Ordinary rock

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor. With Chlorpyriphos EC 20% with 1% concentration

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

R C C WORK

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls {any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-Ill) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly ). All works upt0 plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of layinh but excluding the cost of centering ,shuttering finishing and reinforcement including admixtures in recommended proportions as per IS : 9103 to accelerate rated srtting of concrete, improve workability without impaiting strenth and durability as per direction of engineer in charge (note :- Cement content considered in this item is 330 kg/cum excess/ less cement used as per design mix is payable/ recoverable seperataly All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Centering and shutteing including struting, propping etc and removal of form for Foundations, footings, bases for columns, etc for mass concrete

Centering and shutteing including struting, propping etc and removal of form for Walls ( any thickness) including attached pilasters, butteresses, plinth and string course etc

Centering and shutteing including struting, propping etc and removal of form for Suspended floors, roof , landings , balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shutteing including struting, propping etc and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shutteing including struting, propping etc and removal of form for Columns, Pillars, Piers, abutments, Posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

BRICK WORK

Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75A brickwork in CM (1:3) in superstructure with approved quality of clean coarse sand of FM 2 to 2,5 including providing 10mm thick mortar joints , cost of screening, materials, scaffolding, raking out joints to 15mm depth curing, taxes and royalty all complete as building specification and direction of E/I

providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9"x4'5"x3" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|.

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

WOOD WORK

Supplying, fiiting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors windows skylights fanlights and C/W celetial window opening including wedge over all clamps complete including application of two coats of wood preservative of approved quility onthe surface buttling walls and lintels all complete as per building specification anddirection of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flus

h shutter door and windows with black board core blended with high quality phenol formal clehydes synihetic resin both side commercial veneered of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pe building specrfication and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.9.127.2 1.0 mm thick

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36KGto 80KGand door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120 gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters. The frame shall be filled with mineral wool Insulation having density minimum 96Kg/sqm. The frame will have a provision of G.I. anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80) suitable for fixing in the opening along with factory made template for SS ball bearing hinges of size 100x89x3 mm for fixing of fire rated glazed shutter. The frame shall be finished with an approved fire resistant primer or powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- Charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (paneling to be paid for separately).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per anufacturer’s specification and direction of Engineerin- charge 9.117.1 Extruded section profile size 48x40 mm

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). 12 mm thick frameless toughened glass door

"Thickness of Compact Laminate : 12mm Color of HPL Boards: Dual Standard Compact Color Customizaon :WITH SS 304 FOOT SLIDING LATCH WITH INDICATOR (CORONA SAFETY)Size of Cubicle : 1000mm (W) X 1550mm (D) X 2003mm (H)Door Size : 1750mm (H) x 600mm (W)Divider Size : 1775mm (H)Overall Height Of Cubicle : 2003mm (Including boom Gap of 150mm) Accessories: Standard - Merino Make Aluminum, Stainless Steel - 304 Grade accessories) a) Aluminum ""U"" Channel b) Aluminum ""F"" Channel (Only Corner Unit) c) Aluminum Door Stopper Channel d) Aluminum Top Rail e) SS Coat Hook f) SS Privacy Thumb turn c/w Occupancy Indicator g) SS Door Knob h) SS Spring Loaded Bu Hinges with Cover i) SS Adjustable Foot 316 Grade j) Rubber Door Stopper Lining k) S.S.Screws 304 G & P.V.C Wall Plugs SPECIAL NOTE - Warpage Criteria is 3.0 mm/1000mm for MRS panels as per EN standard- 438.LAMINATE-T LINE BEIGE 871,FMRSUMPPNLZZSS00001 URINAL MODESTY SS MAKE MERINO OR EQUIVALENT"

FMRSUMPPNLZZSS00001 URINAL MODESTY SS MAKE MERINO OR EQ

UIVALENT" "Thickness of Compact Laminate : 12mm Color of HPL Boards: Single Standard and Plain Compact Color Size of UMP : 500mm (W) X 900mm (H)Overall Height Of UMP : 1550mm (Including boom Gap of 650mm) Accessories: Standard - Merino Make Stainless Steel - 304 Grade accessories) - SS a) SS Right Angle Brackets b) S.S.Screws 304 G & P.V.C Wall Plugs SPECIAL NOTE - Warpage Criteria is 3.0 mm/1000mm for MRS panels as per EN standard- 438."

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately).Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC {Wood Polymer Composite} solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives {maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N {Face) & 900N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In• Charge. {Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

STEEL WORK

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Single Skin Roof: Supply and fixing of KingZip/KINGSPAN CURVED “SELF SUPPORTED” SECRET FIX STANDING ROOFING SYSTEM IN 0.9 mm THICK AA 3004 ALUMINIUM ALLOY. The general roof-construction shall comprise from bottom to top:(1) First Layer - Halters – Aluminium Halters/ – in grade 6082 (T6), of suitable height with thermal barrier pads to be fixed to the sub purlins with SS 304 screws only (2) Second layer – Kingspan Jindal KingZip Aluminium 65/400 Straight profile sheeting manufactured from aluminium self-supported standing seam roof system from aluminium alloy AA 3004 H44 (AlMn1Mg1) as specified in BS EN 1396: 2007 minimum material thickness of 0.9 mm and PVDF2 finish ( standard colours ) on the exposed surface.The profiled roof panel should have 24nos. of Micro ribs of height 1.5mm in between 3Nos of Mini ribs for extra strength Accessories, Fasteners. The material properties shall be as follows: Ultimate tensile strength: minimum 200 N/mm2, 0.2% Proof Stress: min 185 N/mm2, Modulus of elasticity: 70,000

N/mm2. Sheets are to be laid to meet the requirements of the building geometry and fixed on Aluminium Halters. Halters to be fixed to the top hat/purlins with SS 304 screws All installation is to be carried out by approved trained roofing installer. The roofing system provider should have both Factory Mutual (FM-4471) & UL Certification (UL-90). The Roofing system provider should have Thomas Bell Wright International Consultants certificate against the testing done for Water leakage ( Static & Dynamic ) and Air Infiltration test as per ASTM E 283-04,ASTM E330-02 (2010),ASTM E331-00, AAMA 501.1.05,AAMA 501.2-09 . All installation is to be carried out by approved trained roofing installer. The installation team shall be fully trained and approved by the supplier.

Aluminium Flashing 0.9 mm thick: Flashings manufactured from aluminium alloy AA 3004(AlMn1Mg1) as specified in BS EN 1396: 2007 minimum material thickness of 0.9 mm and Fluorocarbon PVDF finish on the exposed surface. The material shall be other same colour. Girth – 400mm to 570mm

Gutter- Providing and fixing of 2 mm thick Aluminium gutter with double side vulcanised rubber Expansion joints at every 6m length. Necessary down take spout with diameter upto 150 mm at required intervals & other accessories like Cover plate, end caps and welding at joints. The Girth of gutter would be upto 1200mm.

Supplying,frtting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer. Using M.S. angle 40x40x6 mm for diagonal braces

FLOORING WORK

Providing and laying heavy duty vitrified floor tiles of approved shade and make, conforming to IS:15622, Group B I a (water absorption ≤ 0.5%), size 600x1200x10 mm or approved equivalent, double charged/full body/homogeneous type with matt or anti-skid finish, laid over a 15 mm thick cement mortar bed in proportion 1:4 (1 cement: 4 coarse sand), and fixed using high polymer-modified quick-set tile adhesive (Type II as per IS:15477) in average 6 mm thick bed over prepared surface, including filling joints (approx. 3 mm) with epoxy grout/white cement mixed with matching pigment, curing, cleaning, edge finishing, machine cutting wherever required and disposal of debris, all complete as per drawing, specifications and direction of Engineer-in-Charge.

Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 SQM

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade

Providing and laying 25mm. thick kotah stone slab flooring of approved size, texture and colour over 19 mm thick base of lime morter (1:l:1) ( Lime putty : surkhi: coarse sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size.

Providing and laying 25mm. thick kotah stone riser of steps, skirting and pillers of approved size, texture and colour over 12 mm thick cement morter (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1 : 3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specificaton and directon and E/I.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing curing and po

lishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Granite stone 18 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying 1st quality Ceramic glazed wall tiles thickness to be specified by the manufacturer) in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

ROOFING & WATER PROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Roof/Terrace Water proofing:

Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."

(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectifcation to be done as per satrsfaction of E/C protected from damage before screed over it. Watqr proofing Brand:*Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copolmer, Part B Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370)Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.'15) Elongation at Break -35% without Fibre Cloth and 20% wilh Fibre Clot (Accordrng to ASTM D 2370)

(d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured."

itemH1Code689

(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years.

Covering of treated surface wrth PCC :- Providing 50mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Providing and mixing Liquid lntergral water proofing compound in Conctrete or plaster as per rnanufacturer specificatioqand as per cjirection of Eng - in Charge Brand- Sika Plastocrate plus, MYK proof WP 1 0, Fosroc-Cc.rnplast X4211 C, Dr fixit Pidiproof LW+ or Equivalent

Providing and filling of 6 mm groove between 50mm PCC panels with 6 mm thick deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring grade)as per drawing and technical specification and direction of E in charge (with 18 % GST ). Brand:- sika - polysulshide,fosroc- thioflex 600, dr fixit pidi seal PS (42P) ,MYK seal PS or euivalent.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applyi

ng cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

FINISHING WORK

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing two coats of oil bond Distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone of fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification direction of E/I

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls, scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

ALUMINIUM WORK

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid .in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 10 mm depth and 10 mm width

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/ structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent biMTR.allic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the periMTR.er for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site condi

tions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc.,

enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having

all the performance characteristics etc. all omplete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in SQM. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 SQM from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing MTR.hod for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331- 09 testing MTR.hod for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing MTR.hod for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME- 330-10 testing MTR.hod for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing MTR.hod for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Supply and installation of 4mm thick Aluminium Composite Panel shall consist top and bottom Aluminium Sheet of 0.5mm thickness of Aluminium Alloy AA3105 grade H 14 temper passing EN 485-2. The top sheet shall be coated with PVDF/FEVE coat by continuous coil coating process and shall be of 25 - 28micron thickness passing AAMA 2605 standard and has 15-year warranty. The bottom Aluminium sheet shall have service coat. The 3mm thick core shall be of FR mineral and the ACP shall be Factory Process Certified for FR in accordance to DIN 4102 Class B1. The Aluminium Composite Panel shall be supplied from the certified unit. The weight of the ACP Panel shall not be less than 7.3 Kg/Sqm.The Rain Screen cladding will have all the supports of Aluminium Extrusion designed of AA6063 T5 grade in accordance to EN 485-2. The frame work shall be done by using Male Female RAIN SCREEN System having Aluminium Alloy 6063 T5/T6, Omega Profile ALPL/P/211, Male Profile ALPL/P/311 & Female Profile ALPL/P/312. All ACP old at corners shall be provided with 'L' Cleat of 2 mm thick at suitable interval. It is recommended to coat all the extrusions with PVDF powder coating of 45 to 60 microns having 10year warranty in accordance to AAMA 2605. The cladding shall be so designed that all the expansion joints are open and in accordance to linear thermal expansion of the alloy. Only on the last end joints weather silicon seal shall be used to pack the system and not allow any water seeping through the ends. All the expansion joints kept open shall be ventilated and allow air circulation to keep the building cooler in summers and warmer in winters. These joints shall also be pressure equalized so that water shall not touch the building walls. Normal to the plane of the wall between supports, deflection of the secured perimeter-framing members shall not exceed L/175

or 3/4", whichever is less. Normal to the plane of the wall, the maximum panel deflection shall not exceed L/60 of the full span. Maximum anchor deflection shall not exceed 1/16". At 1-1/2 times design pressure, permanent deflections of framing members shall not exceed L/100 of span length and components shall not experience failure or gross permanent distortion. At connection points of framing members to anchors, permanent set shall not exceed 1/16". MAKE-Aludecor ,Alucobond,Alpolic and Arey ovine.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all Tsections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Designing, Manufacturing, supplying, fixing and testing of Glass Fibre Reinforced Concrete (GFRC) Columns including base and capital with thickness ranging from 50mm to 100mm as per approved size, pattern, Design and colour. The columns to be designed for height up to 30 meters considering safety factors as per IS code.Providing and fixing Glass Reinforced Concrete (G.R.C) Column with Capitol and Base of in approved design, pattern, size and colour to be cladded on existing structure of MS or RCC. The column set shall include Capitol and Base in accordance to the size and length of the column. The GRC column should be made from ‘53 grade’ Cement manufactured by ‘JK/BIRLA Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘N.E.G. JAPAN’ or equivalent, Super Plasticizers manufactured by ‘SIKA’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Mould or equivalent. The fixing of column should be ‘Dry fixing’ as per the drawings approved by engineer in charge. the cost includes the cost of scaffolding for height upto 15mtr. The column set shall include Capitol and Base in accordance to the size and length of the column. Frame work to be paid extra as per drawings.

LUXALON® Aluminium, Un-perforated, 300C Ceiling System: Providing and fixing Luxalon® 300C un-perforated Aluminium

panel ceiling manufactured by M/s. Hunter Douglas of approved colour consisting of panel 300mm wide x 30 mm deep x 0.7mm thick with bevel edge, panel length up to 6 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics. The Panels shall abut each other with a narrow V grove. Panel shall be clipped to a baked enamelled aluminium panel carrier of 41.5mm wide x 62mm deep x 0.95mm thick in standard length of 5 mtr made of doubled baked black enamelled aluminium alloy AA (Al. Mg) with cut outs to hold the panels in a module of 300mm closed at a distance 1.00 mtr. Panel carrier shall be fixed to suitable steel substructure provided by the main contractor as per design requirement. Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint, enamelled twice under high temperature, one side with a full primer and finish coat the other side (inner side) with a primer coating and Skin Coat on a Continuous Paint Line. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffusers, columns etc.FINISHING OF SURFACE OF STRIPS FOR INTERNAL USE (ALUMINIUM): The coils from which the aluminium panels shall be manufactured on high speed cold rollforming machine & the coil shall be stove enameled on continuous coil coating paint line with dried in place roller coated application for pre treatment. The coils to go through four stages of pre treatment, three times oven baked through conversion coating, priming and finishing coat, ensuring superior adhesion, high corrosion resistance and good colour retention. The coils shall be painted on both sides after being degreased. Prime coat of at least 5 microns to be applied at both sides, and a black coat of 5 microns of neutral colour to be put on the inner surface and 5 microns of binder and 15 microns of top coat of desired colour shall be additionally provided on the exposed surface.DIMENSIONAL TOLERANCES:Gauge: The tolerance in thickness is 0.03 mmWidth: The tolerance in the width of the strip is +0.2 mm.FIXING: The panels shall be clipped to carriers. The carriers shall be suspended with e help of threaded rods of galvanized steel. The threaded rod hanger to be made of 6 mm dia galvanized steel and suspended to the ceiling by means of anchor fasteners. WORKMANSHIP: The ceiling shall be erected in continuous sequence. Spans would not exceed those approved by the Engineer-in – Charge. All work in this section shall be performed In an efficient manner byinstallers approved by the manufacturers and as per manufacturers recommended procedures. MEASUREMENT: Measurement shall be made correctly to two decimal places and shall be taken out to out of the finished work. Area shall be calculated in square meters corrected two placed of decimal.

Providing and fixing of 16 Passenger Lift/ 1020Kgs / 1.25 Speed / 2 Floors / 2 Stops / Stainless Steel skretch proof with cast iron counter weight and T section guide rail for car and counter with lift licence.Car Cabin approved design and make

CARRAIGE OF MATERIALS

SAND (UPTO 38KM LEAD)

CHIPS (UPTO 37KM LEAD)

METAL ( UPTO 37 KM LEAD)

BRICKS (UPTO 10KM LEAD)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality-Circular shape 560 mm internal dia

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Supplying, filling, spreading & leveling Brick bat inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone

boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

RCC ROAD AND PARKING

Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres.Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.) For Grading -II Material

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing

Cement Concrete Pavement Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in abatching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Screed & Finishing: Only Laying design mix good quality concrete Grade as approved and as directed by the Engineer in charge. Levelling & compacting using Leveller beam & finishing concrete surface, Broom Finish using floater complete in approved panel size with approved slope as per special form work, Timber Formwork with steel 'L' angles, imported tools for flooring, complete workable RMC at site, in panels of approved size as per approved drawing and as directed by the Engineer in charge.

Non-metallic Floor Hardener: ITEM EXTRA STANDARD COLOUR HARDNER - @ 4 KG/SQM

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge.

80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

BORE WELL

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete

. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. column pipe - do - do - all complete job as per direction of E/I.

HORTICULTURE WORK

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

PREPARATION WORKS

Fine dressing of the ground

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m diameter and 1.2 m deep

Holes 90 cm diameter and 90 cm deep

Holes 60 cm diameter and 60 cm deep

Holes 45 cm diameter and 45 cm deep

MAINTAINANCE WORK

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.

TREES

Providing and stacking of Delonix regia (Gulmohar) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) height 120-135 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis krishna height 75-90 cm., multibranched in earthen pot size 30 cm as per direction of the officerin- charge.

Providing and stacking of Ficus religiosa (Peepal) height 150-165 cm. in poly bag size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus benghalensis (Banyan) height 120-135 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) height 120-130cm in polybag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Spathodea campanulata height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Plumeria rubara height 120-150 cm., 3-4 branches and thick stem in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Largerstroemia indica of height 90-105 cm. multibranched in poly bag of size 25 cm as per direction of the officerin- charge

Providing and stacking of Polyalthia longifolia (Ashok) height 150-165 cm. in earthen pot size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tectona grandis (Teak) height 150-165 cm. in polybag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tamarindus indica (Imli) height 120-150 cm. in polybag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) height 60- 75 cm. in poly bag size 25 cm as per direction of the officer-in-charge

Providing and stacking of Eugenia jambolana (Jamun) height 150-165 cm. in poly bag size 25 cm as per direction of the officer-in-charge

Providing and stacking of Phyllanthus emblica (Amla) height 150-165 cm. in big HDPE Bag as per direction of the officer-in-charge.

Providing and stacking of Foxtail palm ht. 240-270 cm bottom girth 35-40 cm well developed in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Bottle palm ht. 210-240 cm bottom girth 30- 35 cm well developed in big HDPE bag as per direction of the officer-incharge.

BAMBOO

Providing, stacking and Displaying Bamboo Buddha valley variety with umbrella shape plant having 120 cm to 135 cm ht. plant with fresh & healthy foliage well developed in 40 cm Cement pot/ Plastic pot and as per direction of the officer-in-charge.

SHRUBS

Providing and stacking Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 20 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-incharge.

Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pot of size 30 cm as per direction of the officer-in-charge.

Providing, stacking and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 cm to 60 cm spread 75 to 90 cm ht. plant, specimen bushy plant,in 35 cm Cement Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pot of size 20 cm as per direction of the officer-in-charge.

Providing and stacking Duranta Golden, having ht. 15 cm to 20 cm bushy shape with fresh and healthy leaves in 15

cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bag of size 20 cm as per direction of the officer-incharge.

Providing and stacking of Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pot of size 20 cm as per direction of the officer-in-charge.

Raphis excelsa,lady palm

Providing and stacking of Tecoma gaudichaudi of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (chandni variegated) of height 45-60 cm. with 3-4 branches earthen pot of size 20 cm as per direction of the officer-in-charge.

Providing, stacking and Displaying Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in 20 c.m Earthen Pot/Plastic Pot and as per direction of the officer-in-charge

Providing, stacking and Displaying of Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.

GROUND COVERS

Providing and stacking Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking Chlorophytum (Green), full of leafy suckers in 20 cm size of Earthen Pot /Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Jatropha multifida (red colour) of height 45-60 cm. with 2-3 branches in earthen pot of size 20 cm as per direction of the officer-in-charge.

Sprenger's asparagus,Foxtail fern

Syngonium podophyllum,Syngonium butterfly

Tradescantia pallida

GRASS

ELECTRICAL WORK

Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required. Group A

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required

2x2.5 sq mm + 1x2.5 sq mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire.

2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire

4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire

4 x 16 sq.mm. + 2 x 6 sq.mm. Earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections painting etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA "C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required.

6/32 amps, Single pole

40 amps DP

50/63 amps, TPN

Supplying and fixing Single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 Way (4 + 24), Double Door Horizontal Type

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following Rating, Double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 63 Amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as Required. 40 Amps

TELEPHONE, TELEVISION & DATA SYSTEM

Supplying and Fixing Following Size/ Modules, GI Box Alongwith Modular Base & Cover Plate for Modular Switches in Recess etc. as Required. 1 or 2 Module (78mm x 78mm x 45mm)

Supplying and Fixing Following Modular Switch/ Socket on The Existing Modular plate & Switch Box including connections But Excluding Modular Plate etc. as required.

Telephone Socket outlet.

TV Antenna socket outlet.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm.

Supplying and drawing following pair 0.5 mm dia FR PVC insulated copper conductor, Unarmored Telephone cable in the existing surface/recessed steel/ PVC conduit as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as requ

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying & Fixing Modular Type Computer jack RJ 45 ISI mark 1 Module on existing Mounting plate and box Complete with all accessories as required.

INTERNAL LIGHTING FIXTURES & FANS

SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required.

12W LED Round Down Light

15 / 16 W LED Round Down Light

18 /20 W LED Round Down Light

Bulk Head fitting with 9/10Watt LED.

Supply of LED Mirror Light with power 8/10W rated voltage 230V 50 Hz aluminium/ PC body with rauuning life minimum 30000 Hours

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. 20/22 W LED Tube Light

SITC LED Batten light (System lumen efficacy ≥105 <120 lm/Watt) 40 watt

SITC LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt) 40 watt

Supply & Installation, testing and commissioning of 9-15W LED Bracket Light fitting suitable for 9-15 Watt LED Light with all accessories as required. (Havells Cat no LHFOECE1TZ1O01/ Philips model no 31425/wipro make/ similar to BAJAJ make)

Supply insttalation , testing and commisioning of following size ceiling fan 3 balde confirming to IS : 374:2019 incuding wiring thedown roads of standed lenth ( upto 30 cm ) with 1.5 sqmm PR PVC, insulated copper wire suitable for 230V 50Hz single phase supply etc. compleyte as required. 1200mm (48 Degree) BLDC 5 star rating 32W ceiling fan

Supply and fixing of step type electronic fan regulator on existing modular plate switch box including connection but excluding modular plate etc as required.

Installation, testing and commissioning of ceiling fans/bracket fan of all sizes including wiring the down rod .of standard length (up to 30 cm ) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required.

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

MAIN LT PANEL, HT PANELS & SUB DISTRIBUTION PANELS

11KV SINGLE PANEL HT VCB (INDOOR)- ONE INCOMER CUM OUTGOING IN IP-4X ENCLOSURE

Design, Manufacture and Supply of 1 Panel, 11 kV HT VCB Switch Board with Following Accessories :

Incoming

800A, 11kV, 350MVA for 3 Sec., TP, Horizontally isolated, horizontally drawout type, motorised spring charged, closing mechanism, motor voltage 230V AC, shunt tripping & Closing coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum Circuit Breaker(VCB) With Mechanical & Electrical OFF/ON Indicators & Provided with Following - 1 No.

CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of 100/5/5A ratio - 3 Nos.

IDMT relay with 3 elements for over current (50-200%) and 1 element for earth fault protection(10-40%). - 1 Set

Anti Pumping Relay - 1 Set

Master Trip Relay - 1 Set

Trip circuit supervision relay - 1 Set

Potential Transformers, 3 Phase, 3 Limb, Drawout Type, Resin Cast 11000/(Root 3)/110/(Root 3) Ratio Class 1 Accuracy, 100 VA Burden, with HV fuse on primary side and MCB / MPCB on secondary side. - 1 Set

6 Windows Annunciator with Hooter - 1 Set

1 Window for over current trip - 1 Set

1 Window for earth fault trip - 1 Set

1 Window for master trip relay - 1 Set

1 Window for Emergency Stop Push Button - 1 Set

2 Windows Spare - 1 Set

A set of breaker ON/OFF/Trip/DC control supply healthy/Trip circuit healthy/ Spring Charged VCB in test / VCB in service & R,Y,B phase indication lamps. - 1 Set

Emergency stop push button - 1 Set

Limit switches with 4 NO/ 4 NC breaker auxiliary contacts - 1 Set

Control:- T-N-C (Trip, Neutral, Close) breaker control switch with indication arrangement. - 1 Set

All control wiring with protection & test terminal block as required. - 1 Set

Strip heater with thermostat for moisture absorption. - 1 Set

Suitable for connection to 3C x 240 sq.mm. Cross linked polythelene(XLPE) 11kV cables or as called for. - 1 Set

Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set

HT Danger Plate - 1 Set

Incoming as described above. 1 Sets

Powerpack as Required to Be Included (220V/24V DC), 7AH Battery for Each Breaker Module.

SINGLE PANEL 11KV HT VCB PANEL AS DESCRIBED ABOVE

MAIN LT PANEL

NOTE:- MCCB's Wherever Specified shall have Rotary Handle.

Suppy , installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 2mm CRCA sheet steel fabricated cubical type Main L.T. Panel floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 52, TTA Type, with proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable as required. Panel Should Be Internal Arc tested at 50ka for .3 sec as per IEC61641.

(Under no case temperature of main LT panel shall be more at any point of the panel. To avoid heating necessary exhaust fans shall have to be provided along with top louvers).

Degree of protection IP-42

The internal control wiring shall fuse less. All control wiring and metering protection shall be by MCB's.

Colour: Siemens Gray Powder Coated or as per approved shade.

Powerpack as Required to Be Included (220V/24V DC), 7AH Battery for Each Breaker Module.

SINGLE PANEL 11KV HT VCB PANEL AS DESCRIBED ABOVE

MAIN LT PANEL

INCOMER FROM 160 KVA OUTDOOR TRANSFORMER - 1 Nos each having following

1 Nos. 400 amps four pole MCCB of fault breaking capacity 50 KA (Ics=Icu) fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicator and frame earthing contact ,confiming to IS 13947-2 1993 as amended upto date complete with following Accessories.

1 set of 3 CT's of ratio 400/5A, Class 1.0 accuracy 15 VA burden for APFCR.

Independent manual spring closing mechanism - 1 No.

Microprocessor release (EMI and EMC certified) for over current, earth fault and short circuit protection - 1Set .

3Nos. Phase indicating LED lamps with 2 Amp backup MCB, breaker ON/OFF/Trip indication light with 2A MCB , test terminal block set, MCB , circuits as per standatd practice , auxiallry contact for positive interlocking of the breakers as required.

Shunt trip coil 220 Volt AC.

INCOMER FROM DG SET (62.5 KVA) - 1 Nos each having following only switchgear provision in LT Panel if DG Set required

1 Nos. 200 amps four pole MCCB of fault breaking capacity 50 KA (Ics=Icu) fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and

service/test/isolated position indicator and frame earthing contact ,confiming to IS 13947-2 1993 as amended upto date complete with following Accessories.

1 set of 3 CT's of ratio 200/5A, Class 1.0

Protection releases with LSIG and Over voltage ,under voltage,Reverse power protection Relay & Metering & Accessories for each D G set incomers

3 Nos. Phase indicating LED lamps with 2 Amp backup MCB, breaker ON/OFF/Trip indication light with 2A MCB , test terminal block set, MCB , circuits as per standatd practice , auxiallry contact for positive interlocking of the breakers as required .

Shunt trip coil 220 Volt AC.

1 nos battery charger with DC voltmeter and ammeter suitable for the DG sets (62.5 KVA)

INTERLOCKING

Interlocking logic electrical Interlocking between incomers and bus coupler and it should have auto start and auto trip facility for Automatic Operation of The Breakers With Manual Over Rid Facility.

BUS COUPLER

One Number 400A 4 pole edo ACB as Bus Coupler with ON/OFF Indication.

BUS BAR

500A TPN Aluminium bus bar with heat Shrink Sleeve

OUTGOING

ALL THE MCCB'S SHALL BE EQUIPPED/ PROVIDED WITH ALL ACCESSORIES & IN BUILT PROTECTION RELEASES

1 Nos. 160 AMPS TP+N MCCB

1 No. 200A 50KA 4P MCCB (Spare)

1 No. 125A 50KA 4P MCCB (Spare)

Other items such as

1 set of control wiring

1 Set of designation plates

NOTE :- Adequate Quantity of Fire Suppression system with Pneumatic gas cylinder and Heat Sensitive Pneumatic tubing to be used in panel as per the current fire norms & SURGE PROTECTION DEVICES Type 1 ( Class B), 4 Mode, spar type suitable for 10/350µs surge, 3Nos. phase to earth and 1Nos. neutral to earth with impulse Current Iimp. ≥ 50KA Per mode & In ≥ 25kA per Mode.

Complete Panel as Above

FLOOR DISTRIBUTION PANELS

SITC of cubicle Panel suitable for 415V, 3 phase, 4 wire 50 HZ Ac supply system, fabricated in conmpartmentalized (preferbly) design from CRCA sheet of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN aluminium alloy bus bars of high conductivity, DMC/SMC bus bar supports, , bottom base channel of MS section not less than 50mm x 50mm x 5mm thick, entire pannel shall have a common copper earth bar 25mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of AI. bus bars and control wiring with 2.5 sq.mm. FRLS PVC insulated copper conducter S/C cable, cable alleys, cable gland plates in two half. i/c providing following switch gears :-

INCOMER : 125 AMP 25KA FP MCCB

Other items such as

BUS BAR : 160 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves.

1 Set of designation plates

OUT GOINGS :

FLOOR DISTRIBUTION PANELS

10 Nos 63 AMP 4P MCB Including 1 set of Indication Lamp

3 Nos 40 AMP DP MCB Including 1 set of Indication Lamp

complete panel as above and complete

MAIN LIFT PANEL

Other items such as

Design, manufacture, supply, installation, testing and commissioning of Floor Mounting Panel cubicle type panel fabricated out of CRCA sheet steel , floor mounted totally enclosed switchbaord suitable for use of 415 volts , 3 phase, 50 HZ complete with aluminium bus bar and all accessories including supply and fixing of following incoming and outgoing switchgears, Panel Should Have Double Earthing Provision which connected to the nearest earth grid.

INCOMER : 200 AMP FP MCCB

BUS BAR : 250 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp.

The Maximum allowable temperature for the Bus bar to be restricted to 90 deg C. The temperature rise should be restricted to 45 deg C above ambient temperature.

Shunt trip coil 220 Volt AC.

2 No. 100A 25KA 4P MCCB

1 Nos. 200 amps four pole MCCB of fault breaking capacity 50 KA (Ics=Icu) fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and

1 No. 100A 25KA 4P MCCB

LIFT PANEL (TYPICAL)

INCOMER : 100 AMP FP MCCB

INTERLOCKING

BUS BAR : 125 AMP, 500 Volts, 3 phase 50 HZ 4P high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 0.8 sq mm /amp.

BUS COUPLER

Other items such as

1 No 63 AMP 4P MCB Including Indication Lights (Lift)

1 No 40 AMP DP MCB Including Indication Lights (Machine Room DB)

1 No 40 AMP DP MCB (Spare)

1 No 63 AMP 4P MCB (Spare)

EXTERNAL LIGHT FEEDER PILLAR

Design, Manufacture, Supply, Installation, Testing and Commissioning of Panel Fabricated out of 16 SWG CRCA sheet steel, IP 54, wall / floor mounting type with rain canopy The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid.

INCOMER:

TPN Aluminium bus bar with heat Shrink Sleeve rated for 125A.

18 nos 20A SPN MCB

2 nos 63A 4P MCB

2 nos 40A 4P MCB

1 Set of control wiring

SUPPLY OF L.T. CABLE:

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I).

3.5 core, 300 sq.mm.

3.5 core, 240 sq.mm.

3.5 core, 185 sq.mm.

3.5 core, 95 sq.mm.

3.5 core, 50 sq.mm.

3.5 core, 35 sq.mm.

3.5 core, 25 sq.mm.

LT CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

LT CABLE JOINTING & END TERMINATION

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required.

3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 95 sq. mm (45mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

SUB STATION

Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 5 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with On Load Tap Changer (OL

TC)..... 160KVA

Supply, Installation, testing and commissioning of Automatic Power Factor Correction (APFC) panel, indoor type floor mounted free standing totally enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in compartmentalized designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process for powder coated of approved shade ( RAL 7032-Siemens gray or as approved by Engineer-in-Charge)..... 50 KVAR

Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings.......... 62.5kva

Supply of H.T. Cable

Supply & Testing of following 11 KV (E) grade multicore Aluminium conductor XLPE insulated cable, insulation screening with extruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required. 3 C x 240 Sq. mm 11 KV (E)

H V CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size exceeding 120 sqmm but not exceeding 400 sq.mm direct in ground including excavation, sand cushioning protective covering and refilling the trench etc. as required.

H.T Termination: DSR ITEM

Supply and making Indoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV (E) grade as required. 3 C x 240 Sq.mm (11KV E)

Supply and making Outdoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV (E) grade as required. 3 C x 240 Sq.mm (11KV E)

Supply and Making Straight Through Cable Jointing With Cast Resin Compund, Including Ferrule & Other Jointing Materials for Following Size of 3 core, XLPE Aluminium conductor cable of 11KV (E) grade as required. 3 C x 240 Sq.mm (11KV E)

EARTHING

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Earthing with Copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Providing and fixing 25 mm X 5 mm GI strip in 40mm dia GI Pipe from earth electrode including connection with GI nut bolt, spring, washer, excavation and refilling etc as required

Providing and fixing 25 mm X 5 mm Copper strip in 40mm dia GI Pipe from earth electrode including connection with brass nut bolt, spring, washer, excavation and refilling etc as required

Providing and fixing 25 mm X 5 mm Copper strip on surface or in recess for connections etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

UPS SYSTEM

SITC - Online UPS- Input supply: Three Phase, Output supply: Three Phase, The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up 10KVA (Each Power module shall be < 10 KVA)

CABLE TRAYS

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. (Cable Tray Bends as per Requirement)

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

CONVENTIONAL FIRE ALARM SYSTEM

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25mm dia

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. 2x2.5 sq mm

IP CCTV SYSTEM

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG LSZH as per ANSI/TIA 568 C.2 and ISO/ IEC 11801–2nd Edition, ROHS Compliant, solid copper conductors, tested @250 Mhz, with HDPE insulation of individual conductor and over all Dia of 5.8mm for Connectivity of Hub room to End Point.

Supply, Installation, Testing & Commissioning of 3MP IP Network TDN Low-Light IR Rugged Indoor / outdoor Dome Camera, 1/2.8" CMOS or better, 3MP (2304 x 1296) @ 25fps or better, triple stream at various resolution up to 25fps, Min. Illumination required 0.005 lux @ F1.6 (color), 0 Lux IR On, 4 IR LEDs Smart IR with upto 50m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265 & H.264 High Profile & MJPEG , Triple stream, 2.7 to 13.5mm 5X motorized focus & zoom lens, Field of View FoV H:88°-24°, BLC, HLC, 3DNR White Balance, Minimum Edge Intelligence Video Analytics : Motion Detection, Tampering, 4 Privacy Mask, 8 Region Of Intreset, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 6W, IP 66/67, IK 10 vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certific

ations: ONVIF Profile S/G/T compliant, UL/CSA 62368-1, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000) compliant

Supply, Installation, Testing & Commissioning of 3MP IP Network TDN Low-Light IR Rugged indoor/ outdoor Bullet Camera, 1/2.8" CMOS or better, 3MP (2304 x 1296) @ 25fps or better, triple stream at various resolution up to 25fps, Min. Illumination required 0.005 lux @ F1.6 (color), 0 Lux IR On, 4 IR LEDs Smart IR with upto 60m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265 & H.264 High Profile & MJPEG , Triple stream, 2.7 to 13.5mm 5X motorized focus & zoom lens, Field of View FoV H:85°-24°, BLC, HLC, 3DNR White Balance, Minimum Edge Intelligence Video Analytics : Motion Detection, Tampering, 4 Privacy Mask, 8 Region Of Intreset, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 6W, IP 66/67, IK 10 vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T compliant, UL/CSA 62368-1, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000) compliant.

Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light 2MP 40 X IP IR PTZ Camera, 1/2.8" CMOS, 2MP@ 50fps, H.265, H.264, Min. Illumination required 0.1 lux (color), 0 Lux B/W IR on, 120dB True WDR, HLC, BLC, triple stream, Lens wide 4 to 5mm - Tele 160 to 200mm, 40X motorized focus & zoom lens, Inbuilt/Externla IR uo to 200 Meters, Built in Video Analytics such as Video Motion Detection, Camera Tampering & Auto Tracking, 3DNR, Defog, Electronic Image Stabilization, 24 Privacy Mask, shutter speed 1/1 to 1/10,000 second, PAN Speed upto 400°/s, PAN Range 360° Endless, Tilt Speed upto 400°/s, Tilt Range -20° to +90° (Auto Flip ), 256 Presets, Dual channel Audio G.711a/G.711u/G726, 256GB SD card support, Alarm: 2 In, 1out, High-PoE (UPOE) and 24VAC, IP 66, IK 10 vandal proof, Inbuilt Heater, Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S & G compliant, UL, CE, EN, FCC, NDAA Section 889 & RoHS compliant.

Supply , Installation , Testing and commissioning of 16/32/64 Channel NVR (Network Vedio Recorder), for recording upto 64CH @ 1080P with 08 nos. SATA HDDs minimum 64TB storage or more (recording requirement all cameras recording at 2MP, 25fps for 30 days),H.265/H.264/MJPEG/MPEG4 codec decoding, Front Control Pannel with LEDs Indication, 3 nos. USB, iPhone; iPad; Android based Mobile clients, Video Export feature on USB, Search Mode: Time/Date; Alarm; Motion Detection (MD); Exact Search (accurate to a second); Smart Search, Dual HDMI Output, Alarm Input (16 nos.), Alarm Output (6 nos.), 16 POE Ports, eSATA Device, 320Mbps each Incoiming & Outgping throughput, Operating Temperature –10°C to 55°CCertification : CE, FCC & UL including fixing accessories and cable termination with required connectors/Jack, complete in all respect as per instruction of engineer in-charge.

Supplying, installation, testing & commissioning of 2MP Fixed Dome Network Camera High quality image 1/2.8" CMOS sensor 1920*1080)@30/25fps; 720P (1280*720)@30/25fps Ultra 265, H.265, H.264 Smart IR, up to 30m (98ft) IR distance Day/night, Adjustment angle Rotate: 0° ~ 360°, DWDR, Privacy Mask Up to 4 areas, White Balance Auto/Outdoor/Fine Tune/ Sodium Lamp/Locked/Auto2, Digital noise reduction 2D/3D DNR, Flip Normal/Vertical/Horizontal/180°, HLC Supported BLC Supported, Network 10/100M Base-TX Ethernet, CE: EN 60950-1 UL: UL60950-1 FCC: FCC Part 15.

Supply, Installation, Testing and commissioning of Managable 24 port Switch with Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as required.

Supply, installation, testing and commissioning of of 8 TB HDD all accessories complete as required.

Supply installation and commissioning of 55 inch LED monitor for display of camera.

EXTERNAL LIGHTING

S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. 20/25W LED Post top lamp clear

S.I.T.C of Following rating approved make LED Bollard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, confirming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)

S.I.T.C of Following rating LED Flood Lighting Luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC 50Hz. Luminarie shall be confirm to IS 10332 Part 5/section 5 and shall be complete with all necessary accessories as required.

90/100W LED Flood Light

200W LED Flood Light

S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270

AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required.(Approved Make:- Havells / Philips / Crompton / Wipro). 70/72W LED Street Light

Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm).

1M Single Arm Suitable for 70MM Top

Installation, Testing & Commissioning of the 7 mtr Octagonal Pole & Light Fitting with the help of suitable tools and plants, and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity og 10T/sqmtr but excluding wire and mcb

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I). 2 core, 6 sq.mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. 3½ X 25 sq. mm (28mm)

Supplying and laying of following sizes FR PVC insulated single core copper wire in existing conduit complete as required. 3x2.5 sq mm

Supply of 12mtr High Mast Light in one section construction S355 grade as per BS - EN 10 025 top dia 100 mm, boittom dia 360mm, plate thickness 3mm 12 side polygon galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI Single spike lighting protection, maximum wind speed 47m/s as per IS : 875 (part III) with 6 nos foundation bolt of PCD 445mm TS 600/24mm dia /850mm long. luminarie carriage : material for 40 NB ERW Class B - MS Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded, 2 sections having carring capacity upto 8 luminaries. Trailing cable : 5core 2.5 sqmm. PVC flexible copper conductor winch/power tool : double drum, SWL 750 kg with 0.75HP 6 Pole single speed integral motor rope : Grade AISI 304, 7/19 Construction, dia 5mm, BLC 1450 x 2 having 2 no of continuos rope. aviation obstruction light: twin dome aviation obstruction lights LED type as required. (but excuding feeder pillar)

Installation, Testing, Commissioning of High Mast and Light fixture with help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC Sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 Grade concrete for the high mast considering safe soil bearing capacity of 10T/mtrs sq for 12 mtr High mast

MANHOLE & HUME PIPE

Providing and laying non pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixtures of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

150 mm dia

250 mm dia

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

HDPE PIPES

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.

SPILT AC UNITS

SITC of 1.5Tr. 5 Star split A.C (Inverter Type) IS-1391-part-1

SITC of 2.0Tr. S Star Split A.C (hiverter Type) IS-1391-part-l

SITC of Copper Tube of size l I 4 '' for split ac unit 1 /l.5/2/3 tr capac:ty nitride rubber insul;1tion

SITC of 4 KVA wall mounted .:iutom;ltic voltage STABLIZER from range HOV to 28OV

SITC of Drain pipe for ac

SITC Outdoor stand for 1.5Tr Split AC

SITC Outdoor stand for 2.0Tr Split AC

HVLS FANS (HIGH VOLUME LOW SPEED)

Supply, Installation, Testing and Commissioning of energy saving high volume low speed ceiling mounted fan consisting of 8 airfoil blades, 14 feet diameter (sweep), VFD (variable frequency drive) operated with inbuilt protective module with maximum speed 80 rpm, air delivery 7550 cum/min, maximum power 0.4 kW, noise limit 43 dB suitable for operation on 230 V, 50 Hz ac supply including making connection with suitable size wire (as prescribed OEM) upto length of 30 m, inclusive of fixing materials etc. complete as required.

PLUMBING WORKS

SANITARY INSTALLATIONS

Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I 'p' trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M long with one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all complete as per specification and direction of E/I. (A) 580 mm. long (c) With 10 lit. low level PVC Cistem

Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I. (ii) E.W.C. with 'S' trap (b) 10 lit. low level PVC Cistem

(b)Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.

(i) 600mm x 450mm size

(c)(iii) C.P. brass liquid soap container

Provinding and fixing wash basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good t

he walls whereever required : White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer

Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete Flexible Pipe 32/40 mm Dia

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Providing and fixing CP brass single lever low flow Sink mixer with 15 mm CP brass single lever pillar cock with pop up and waste complete including cutting and making good the walls where required.ROCA make (Model -RT5A3060C00) or Equivalent.

Providing and fixing C.P concealed four way diverter with thermostatic mixer with shut off valve and diverter, including cutting and making good the walls, wherever required. (Make:- Jaquar - Four way diverterKUB-35421, Thermostatic mixer 35671 or Equilent)

Providing,Fixing satin finish stainless steel AISI 316 grade wall mounted coat hook on door complete. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. MAKE JAQUAR MODEL NO.- ACN-1161N or EQUIVALENT.

DRAINAGE INSTALLATIONS

Providing, fixing, testing and commissioning of UPVC SWR pipe type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps etc. conforming to IS:14735-1999 and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint as required/applicable. 110 mm (OD)

Providing, fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design having 50 mm water seal with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) including cost of cutting and making good the walls & floors wherever required. 110 mm inlet x110 mm outlet.

Providing, fixing, testing and commissioning of UPVC inlet fittings (hopper) receive waste from fixture waste with maximum 3 inlets 40, 50 & 63 mm OD size, fabricated from 110 OD UPVC SWR pipe, UPVC sockets, fixed to UPVC traps including solvent weld joint/rubber ring joint, complete with all civil work set in cement concreate 1:2:4 as required including cost of cutting and making good the walls & floors wherever required.

Providing, fixing, testing and commissioning of UPVC waste Pipe conforming to IS : 4985-2000 class III including all moulding fittings conforming to IS : 7834 (Part-1 - Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For fixtures waste).

Providing and fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD

Providing,Fixing satin finish stainless steel AISI 316 grade wall mounted coat hook on door complete. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. MAKE JAQUAR MODEL NO.- ACN-1161N or EQUIVALENT.

DRAINAGE INSTALLATIONS

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround 100mm dia. SW / CI / waste pipes including bed concrete as per standard design

Providing, fixing, testing and commissioning of UPVC rain water pipes (IS : 4985-1983 class-III ) including injection moulded fittings (heavy duty) (plain or door) e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site [For Balcony Drain + Terrace Rain Water Downtake Pipe]. 160 OD

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATER SUPPLY INSTALLATIONS

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (Exposed on wall Terrace)

32 mm dia, nominal bore

40 mm dia, nominal bore

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40 mm nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete.

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm dia nominal bore

Provide and fixing PTMT ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D. plastic ball 50 mm dia NB, 242mm long. Weighing not less than 1240 gms.

Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitting, including fixing the pipewith clampsat 1 m spacing. This includesjointing of pipes &fittingwith one step CPVC solvent cement and cost ofcutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.(Concealed work including cutting chases and making good the walls etc.)

15mm nominal outer dia. Pipes.

20mm nominal outer dia. Pipes.

25mm nominal outer dia. Pipes.

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The

tail pieces, tapers etc if required will be paid separately) : 50mm diameter

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified 100 mm nominal bore 50 mm dia.

Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design. 32 OD mm.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. With F.P.S. bricks

SEWERAGE & DRAINAGE INSTALLATIONS UPTO MAIN ROAD FIRST MANHOLE

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:

150 mm diameter

200 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

150 mm diameter S.W. pipe / RCC pipe

200 mm diameter S.W. pipe / RCC pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 180 x 150mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes: Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

For pipes 350 to 450 mm diameter

Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FIRE FIGHTING WORK

(WET RISER SYSTEM - PUMPING EQUIPMENTS)

Supplying, Installation, Testing and Commissioning of Electric Driven Pressurization Pump (TERRACE Pump) suitable for auto operation and consisting of following: complete in all respects as required. The pump shall also be capable of discharging not less than 150 % of the rated discharge at a head of not less than 65% with the rated head.

a) Horizontal type, centrifugal end suction type pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal, gland packing and flow of 450 Ipm at 35Mtr. head confirming to IS:1520.

b) Suitable HP (Minimum 4.0-5.0 HP) squirrel cage induction motor TEFC type 2900 RPM suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP-55 class of protection for enclosure, horizontal foot mounted type with Class - 'F' insulation, confirming to IS:325.

c) Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge , pressure switch with valve etc. Suitable cement concrete foundation duly plastered, with anti vibration pads etc. complete as per manufacturer's design & standards and as per detailed specifications.

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header on the top of each riser fabricated out of 6 mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal ball valve complete with all accessories etc. pressure gauge, synthetic enamel paint of approved shade as required of the following sizes 1.2 Meter high and 250 mm dia

(HYDRANTS SYSTEM)

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS : 5290 (Type A), with 80 mm dia flanged inlet, with ABS cap and chain complete with all accessories etc. as required.

Supply, Installation, Testing and Commissioning of 63 mm dia. 15 Mtr. Long RRL hose pipe with 63 mm dia. male and female stainless s

teel couplings duly binded with GI wire rivets etc. ISI marked, IS 636 (type-A) as required.

Supplying and fixing 63 mm dia. Stainless Steel branch pipe with 20mm dia nozzle conforming to IS:903. suitable for instantaneous connections to hose pipe coupling etc. as required.

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction, spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required. 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 20 mm dia. ball valve & nozzle. Drum and brackets for fixing the equipments on wall. Connection from riser with 25 mm dia (Gun metal) stop valve & M.S. Pipe.

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following.

Gunmetal single headed Hydrant valve - 1 No.

Fire Hoses 63mm, 15 M long with accessories - 2 Nos.

Short branch - 1 No.

First Aid hose Reel - 1 No.

Fire Extinguisher - 2 Nos.

Fireman's Axe - 1 No.

Pressure Gauge - 1 No.

The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way - 100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

(PIPING, VALVES AND ACCESSORIES)

Supplying, laying, fixing, testing and commissioning of following sizes (NB) of class 'C' M.S. pipes confirming to IS 1239 and 3589 including cutting, threading, welding etc. and providing all fittings e.g. elbows, reducers, clamps, hangers, flanges, gaskets, nuts, bolts and washers etc. including painting of pipes and fittings with red paint over a coat of ready mixed primer, both of approved quality and shade including cutting holes and chases in brick or RCC walls/slabs and making good the same etc. complete in all respect as required. (The Welding shall not be done for piping less than 50 mm dia.)

150 mm dia

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. 20/22 W LED Tube Light

100 mm dia

80 mm dia

65 mm dia

25 mm dia

Supplying, Installation, Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with EPDM rubber lining seat and CF-8 stainless steel disc duly ISI marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required.

150 mm dia

65 mm dia

Providing, Installation, Testing and Commissioning of double flanged cast iron Dual Plat Check Valve (Non-Return Valve), PN 1.6 of following sizes confirming to IS : 5312 complete with EPDM rubber lining seat and stainless steel disc, rubber gasket, Gl bolts, nuts, washers etc. as required. 150 mm dia

Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required. 150 mm dia

Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications. 150 mm dia

Providing & fixing of pressure gauge in M.S. pipe line including connection etc. as required.

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

(FIRE EXTINGUISHERS)

Powder Fire Extinguisher (Stored Pressure type) Capacity 09 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe locking arrangement, pressure gauge, operation manual and bracket. Operating Temperature: - 10ºC to + 55ºC. Brand LIFEGUARD

Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006 4.5kg capacity cylinder

Providing and fixing in position approved make fire bucket of 24 gauge, galvanized steel, standard 9 liters capacity and of round bottom shape, panted white inside and red outside and black on bottom dome with letters ‘FIRE’ in black and gold with all mounting bracket and screws.

Providing and fixing of fire Bucket Stand including sheet metal (16 gauge) shade for 2 buckets. Platform and associated civil works complete.

(MOTOR CONTROL PANELS)

Supplying, assembling, erecting, connecting, testing and commissioning of Outdoor type fire fighting double door lockable type with epoxy paint. This panel shall be mounting on MS/brick pedestal support upto 400 mm high from ground level,cubical, dust, vermin proof and outdoor type (IP65) fabricated as per specification laid in document with following incomming and outgoing feeders including making connections/inter-connections testing and earthing etc. required with necessary interlocking with existing panel as shown in drawing as per specification and mounted with the followings.

1 No. - 630A 4P ATS

1 No. - 630A TPN MCCB of fault breaking capacity 50 kA (Ics = Icu upto 500V), fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with following accessories for each MCCB.

Independent electrical/manual spring closing mechanism - 1 No.

Microprocessor releases based relay(EMI & EMC certified) for over current, earth fault & short circuit protections with trip indications for each - 1 set.

Dual core calibrated digital Multifunctional meter of class 1.0 to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral) and 3 Nos. dual core CT of A Class 1.0 accuracy and 15 VA burden.

Following indicating lamps and push buttons for each MCCB with back up 2A SP MCB .

3 No. Phase indicating Lamps .

Indicating Lamps for the following;

Bus Bar

800 Amp. 50 kA, TPN Al. Bus Bar

Outgoings:

Following rated 420V,50KA MCCB's with overcurrent and short circuit releases Microprocessor based with ON,Trip indications, front operating handle & door interlock along with 2A SP MCB backup protection and control terminals & wiring as required. etc. complete in all respects as mentioned in specifications and as required For each outgoing:

125 Amp. TP MCCB -4 Nos.(4 spare)

16 Amp. TP MCCB -2 Nos.(2 spare)

quired. - 2 set.

The Panel shall have necessary arrangement to start the pumps at automatic mode in following sequence. a) The Jockey Pump is start to maintain the drop in pressure in pipe line and also in case of opening of any hydrant to maintain the required pressure. b) The main fire pump will start in case of jockey doesnot able to maintain the required pressure due to opening of any fire hydrant. c) To start the diesel engine operated fire pump in case of failure of power supply or in case of minimum fire pump is not able to required pressure.

(d) Diesel Engine Control

Control for Diesel Engine comprising:-

(ii) Indication lamp for High Water Temp. and Engine on indication and suitable tripping devices, overload, earth fault protection relays etc as required.

(iv) All standard relays and accessories for automatic operation of diesel engine.

(e) System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of Main Fire Pump, Pressurization Pump in sequence as per specification consisting of relays, timers, sensor, annunciation window for fault indication, complete as per specification.

Fire panel as above

FURNITURE WORK

BED (WITH BOX):- Having an overall size of 1875mm x 900mm x 410mm. The Frame of the Bed is made of CRC ERW rectangular pipe of 50mm x 30mm size 1.5mm thickness. The Back rest of the bed is made of MS CRCA sheet of 2mm thickness. The bed has a modular construction the main frame having an overall size of 1770mm x 900mm is placed on a four 100mm x 100mm conical supports duly nut bolted to the head and leg side frame. The leg and head frame have a metal insert connector (pipe insert) 100mm long. The insert will add to the load bearing capacity of the bed. The bed shall have levellers made of nylon studs with screw inserts with adjustment of 10mm. HOSTEL BED BOX Dimensions:- Having an overall size of 1200mm x 840mm x 381mm. The Bed Box frame is a combination of 0.8mm and 1.0mm thick CRC steel sheet confirming to IS:513 grade D quality on the main body and top lid respectively. The top lid shall have minimum three and two stiffeners on the horizontal side and vertical side respectively. The lid has two hinges. Thus, having a load bearing capacity of 150 Kgs approx. The Legs of the storage box are made of 1.6mm thick CRCA MS sheet. The bed box shall have levellers made of nylon studs with screw inserts with adjustment of 10mm. Colour Available as per Client Choice- Brown, Blue, Orange, Green, Yellow With Glory Colour. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

MATTRES:- ECOAIR™ LATEX MATTRESS, Size -As per Bed, Double Sided, Removable Cover, Firm Fill Material-Memory Foam. Nilkamal Sleep Product Dimensions as per bed size specifications Pinhole technology for superior air circulation Latex foam for bouncy and supportive feel, alleviating body pain Removable and washable zipper cover Cool Tencel fabric for soft touch & comfort Durable & long lasting Warranty for 10 years. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

STEEL LOCKERS:- Locker type Having an overall size of 1855 mm H x 480 mm W x 480 mm D. Conforming to BIS specification IS:3314-1984(with latest amendment). 5-lever lock conforming to IS 729(latest). Internal locking arrangement (for 6 locker type). Pedestal fitted with 3 mm Teflon bush with 125 mm Pedestal height. Steel sheet material- Cold reduced carbon steel sheet conforming to CR0 grade of IS 513:2016 (with latest amendment). Minimum thickness of steel sheet for sides, back, top, partition, shelves, doors, pedestal- 0.8 mm thick, Hinges Plain butt type made from M.S sheet of minimum 1.6 mm thick. Handle of each door made up of Electroplated mild steel. Finish coat with enamels conforming to IS 151(latest), Colour Available as per Client Choice- Brown, Blue, Orange, Green, Yellow With Glory Colour. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certifi

cation. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.

SS DINING TABLE 6 SEATER WITH FIXED CHAIR:- Overall size of the Dining Table 7’ L x 3’ W x 30” H total stainless steel (S.S) structure & body. Table top height is 30” from floor level and round type sitting stool height is 18” from floor level: all structures using 16-gauge S.S square frame (2” x 1”) and S.S sheet of 18 gauge with necessary bending and molding: Total 8 Nos. round sitting top (S.S) attached design in both sides. All S.S sheet will be SS 304 grade and 18-gauge (totally rust and moisture proof), pipe for sitting stool OD is 2” round S.S tube and table to tool pipe OD is 1 ½” (one and half inch) round S.S tube (16 gauge). Main Table Top thickness is 1”. THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018, ISO 21015:2007, IS 13871:1993 (7 Stage Powder Coating). GREENGUARD GOLD BY UL Certificate UL 2818-2022 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings along with Green-guard by certification compliance. (AII ISO Certification is from NABCB and IAF accredited certifier only}. Girha Certificate, AIOTA (All India Occupational Therapists Association) for Office, Educational & Hospital Furniture Range, IGBC (Indian Green building Council) certification.ISO 13485:2016, The OEM should be a member of BIFMA. The name of the OEM should be reflected in BIFMA website. BIFMA (Business& Institutional Furniture Manufacturers Association) Level-3 certification. IAQ Gold Certification for atleast 10 products and certificate has to be submitted for the same. GRIHA CERTIFICATION- GRIHA V.2015 & SVAGRIHA For Atleast 10 Products.