COMPREHENSIVE DAY TO DAY MAINT VARIOUS B/R, E/M AND B/S RELATED ITEMS IN WING I, II, IV, AND V AT ARTY CENTRE UNDER GE NASIK ROAD CAMP.

Amount

Attending day to day complaints related to joinery work such as repairs to cupboard, kitchen shelves, pelmet box, easing of doors and windows, kitchen knobs fitting and fixing wire mesh, glass, repair of aluminum shutters etc as ordered/required on all working day to attend the complaint cell by rep of contractor at 0900am and report to complaint cell at every evening at 0500pm on daily basis after satisfactory complition,complete all as specified and directed. Material such as nails,screws, washers, putty/beading for glass, nut & bolts shall be included in the quoted rate. Note :- (i) The complaint against docket shall be taken from MES Complaint cell at every morning at 0900 am by rep of contractor on daily basis. (ii) Every docket will submitted at complaint cell on daily basis of same day at 0500 pm or early morning on next day after satisfacotry complition. (iii) Necessary T&P, equipment and safety gear shall be provided by the contractors. (iv) Rs. 150.00/complaint shall be recovered against non attending of every complaints. (v) Material will be measured (after fixing) and paid separatly as supply only under respective items. Note :The complaints of docket for B/R portion, E/M portion & B/S related items shall be taken from MES complaint cell by rep of the contractor & also dress code for rep of Contractor / worker shall be followed as approved by GE

Supply only wooden beading exc 13 sqcm but n exc 25 sqcm Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads

M&L for fixing in repair 25 mm matt finish Stainless steel curtain rod best quality as approved by Engr-in-charge

M&L for fixing in repair Stainless steel ornamental piece with bore dia of 25 mm for free end of curtain rod .

M&L for fixing in repair Stainless steel projecting bracket to support curtain rod of size 25mm.

Supply only Door stopper of stainless steel body.

Supply only Galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm including necessary beadings and fillets complete all as specified and directed.

Supply only 3mm thick sheet glass ordinary quality, in square or reqd shape n exc 0.50 Sqm each pane including oil putty complete all as specified and directed.

Supply only 200mm long mild steel barrel tower bolt, stove enamelled black with bright bolt complete all as specified and directed. .

Supply only 250mm long sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Supply only 150mm aluminium alloy handle, cast type, anodised

Supply only door closer hydraulically regulated,designation No.1universal type, Aluminium body suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed.

Supply only glass shelf assembly consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply only Towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Attending day to day complaints related to water supply only & plumbing work such as leakage of bib cock,/pillar cock/ stop cock angle valve of any description changing the washers, cleaning of air lock in the pipe, leaking low level or high level flushing cistern by adjusting the float valve and including removal and replacement of rubber washer in PVC siphons and adjusting the float valve of over head tanks and leaking PVC bends/galvanised iron pipes etc as per site requirement on all working day to attend the complaint cell by rep of contractor at 0900am and report to complaint cell at same day at 0500pm on daily basis after satisfactory complition, complete all as specified and directed. Material such as threads, washers, lead etc shall be included in the quoted rate. Note :- (i) The complaint against docket shall be taken from MES Complaint cell at every morning at 0900 am by rep of contractor on daily basis. (ii) Every docket will submitted at complaint cell on daily basis of same day at 0500 pm or early morning on next day after satisfacotry complition. (iii) Necessary T&P, equipment and safety gear shall be provided by the contractors. (iv) Rs. 150.00/complaint shall be recovered against non attending of every complaints. (v) Material will be measured (after fixing) and paid separatly as supply only under respective items.

Supply only water tank cover for tanks of size 500 ltr or 1000 ltrs complete all as specified and directed.

Supply only PVC seat cover for EWC of white colour complete all as specified and directed.

Cleaning of RCC/PVC water storage tanks any type of capacity by removing organic material and dirt etc. from wall and base after bailing out/opening wash out and plugging inlet pipe and washing the surface by applying bleaching powder or any other approved by Engr In Charge, including taking down and refixing of any type and size of pipe and filling with fresh water and replacing the top cover in position etc as per direction of Engr In Charge

Supply only 15 mm bore bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply only 15 mm bore bib tap, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply only 15 mm bore Stop valves, cast copper alloy, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

All as per above Item No.22.00 but 20mm bore.

Supply only 15 mm bore Stop valves, fancy type chromium plated cast copper alloy, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply only 15 mm bore Pillar taps, cast copper alloy , with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply only 15 mm Brass CP Wall Mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Supply only 32mm waste fittings, brass, chromium plated for wash hand basins,sinks etc with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed complete all as specified and directed.

All as per above item No. 27.00 here- in- before but 50mm dia.

Supply only Grating doom 125mm dia of stainless steel with hole/without hole complete all as specified and directed.

Supply only 15mm PTMT Bib tap standard of any colour screwed, for iron pipe and fixed complete all as specified and directed.

Supply only 15mm Ball valves, high pressures of PTMT, with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe, Minimum wt (15mm -142gms) complete all as specified and directed.

All as per item No. 31.00 here- in- before but size 20mm dia and Minimum wt (for 20mm -210gms)

All as per item No. 31.00 here- in- before but size 25 mm dia and Minimum wt (for 20mm -210gms)

Supply only hand shower (Health faucet) 1 Mtr PVC tube wit wall hook (CP)

Supply only 15mm bore steel water tubing medium grade galvanizes for fixed to walls, floors, roof ceiling etc including thread, soluvent and etc complete all as specified and directed.

Supply only 25mm bore steel water tubing medium grade galvanizes for fixed to walls, floors, roof ceiling etc including thread, solvent and etc complete all as specified and directed.

Supply only 20mm bore steel water tubing medium grade galvanizes for fixed to walls, floors, roof ceiling etc including thread, solvent and etc complete all as specified and directed.

Supply only GI nipple, and socket 25mm bore size complete all as specified and directed.

Supply only GI Elbow, and Tee 25mm bore size complete all as specified and directed.

Supply only GI nipple, and socket 15mm bore size complete all as specified and directed.

Supply only GI nipple, and socket 20mm bore size complete all as specified and directed.

Supply only GI Elbow, and Tee 15mm bore size complete all as specified and directed.

Supply only GI Elbow, and Tee 20mm bore size complete all as specified and directed.

Supply only Socket reducer, and Tank connection 20mm bore size complete all as specified and directed.

Supply only PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

All as per above item No. 45.00 here- in- before but 600mm long.

Disconnecting existing tanks, exc 500 & n exc 1000 setting aside (or lowering if required), cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position.

S&F 500 ltr capacity rotational mounded polythylene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position including disconnecting unserviceable PVC/Cement water storage tank of 500 Ltr capacity complete all as specified and directed.

S&F 1000 ltr capacity rotational mounded polythylene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position including disconnecting unserviceable PVC/Cement water storage tank of 1000 Ltr capacity complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore.

Supply only 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe and brackets complete all as specified and directed. Specification of flushing cistern shall be as per IS 7231-1994.

S&F in repairs Vitreous China wash basin white, flat back, size 550 X 400mm, including cutting for and pinning in ends of brackets or erecting stand, with and including 32mm waste fitting brass, chromium plated with long screwed shank and fly-nut, flange end bedded in red lead cement, brass chromium plated bottle trap with inlet and outlet screwed for pipe or connections 32mm bore, including necessary packing, union and cap and fixed in repairs. Note:wash basin shall conform to IS 2556(part-4)-2004.

M&L for Vitreous China urinals, half stall type (back or corner wall type), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with and including 5 litres PVC automatic flushing cistern, including brackets, flush pipe, CP urinal spreader, grating union, , union and cap and discharge pipe; fixed in repairs.

M&L for Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with and including 5 litres PVC automatic flushing cistern, including brackets, flush pipe, CP urinal spreader, grating union , union and cap and discharge pipe; fixed in repairs.

M&L for PVC (SWR) floor trap(75 mm dia), plain with grating including jointing with solvent cement to mitigate the site requirement to the entire satisfaction of engr-in-charge.

Supply only 15 mm dia gun - metal globe or gate valves with iron wheel head ,screwed both ends for iron pipe and fixed

Supply only 20 mm dia gun - metal globe or gate valves with iron wheel head ,screwed both ends for iron pipe and fixed

Supply only soap dish, fixed to plugs with chromium plated brass screws etc complete all as specified and as directed.

Supply only 40 mm dia Low density polyet?hylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.

Supplying only 20 mm dia of CPVC pipes outer diameter SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified

Supplying only 25 mm dia of CPVC pipes outer diameter SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified

Supply only CPVC Elbow 20 mm dia for outer diameter

Supply only CPVC Brass Elbow (3/4 X ½) 20 mm dia for outer diameter

Supply only CPVC Tee 20 mm dia for outer diameter

Supply only CPVC Male Brass Threaded Adaptor (MTA/ MBTA) ) 20 mm dia for outer diameter

Supply only CPVC Female Brass Threaded Adaptor (FTA/ FBTA) 20x15 mm dia for outer diameter

Supply only CPVC Tank Adaptor 20 mm dia for outer diameter

Supply only CPVC UNION 20 mm dia for outer diameter

Supply only CPVC Elbow/socket reducer 25 mm dia for outer diameter

Supply only CPVC Tee 25 mm dia for outer diameter

Supply only CPVC Male Brass Threaded Adaptor (MTA/ MBTA) ) 25 mm dia for outer diameter

Supply only CPVC Female Brass Threaded Adaptor (FTA/ FBTA) 25 mm dia for outer diameter

Supply only CPVC Tank Adaptor 25 mm dia for outer diameter

Supply only CPVC UNION 25 mm dia for outer diameter

supply only 32 to 40mm dia PVC waste pipe for wash basin and kitchen sink complete all as specified and directed.

Supply only ms clamps Fixing only 20 mm pipes to walls/chases/ceilings or laying in floors

Supply only ms clamps Fixing only 25 mm pipes to walls/chases/ceilings or laying in floors

Cleaning of blocked WCs /nahani traps/floor traps/ urinals of any dia by rodding only.

Cleaning of existing sewage line of any dia by roding including removal of sludge and taking out sewage water where required and finally flushing with clean water & The length will be measured from the first manhole to last blocked manhole including manhole in between.

Cleaning of manholes of any size taking out sludge , effluent ,sand,, grit, ash, rags, fibre and string material etc complete and disposed as directed by Engr in-Charge

Receiving complaints from JE incharge lodged by the user/occupants of electrification nature, rectification of the fault as per the compaint lodged by the user onward KWH meter in respect of main distribution board having switch board, fused, MCB distribution board in sheet metal enclosure, point wiring fixture for light/fan /bell /light or power sockets, metal clad plug socket complete repair to the extend by removing connections from the system, removing faults in (surface /concealed) wiring/ circuits, sunken boxes, Junction boxes, main switches, MCBs/DBs any type of utility light fittings, lamp holders, AC ceiling fan/exhaust fans and other connected fixtures of internal electrification including providing stores such as wires of appropriate size and conductor matching to existing one upto the light of 2 mtr, insulation tape, screws, nuts as per the site requirement to rectify the fault with regard to complaint lodged and refixing of fitting and fixture to their original position as dismentled complete all as directed at site to the entire satisfaction of Engineer -in- Charge. Note : (i) Any complaint which is left out/unattendent 2 days by the electrician by any reasons the same to be communicated to the JE incharge /AGE E/M with reason. (ii) New material/stores provided for completing the job shall be measured and paid for separetely under relevent items of sch 'A'. (iii) Contractor shall provide the all type of T & P to each electrician for attending the internal electric complaints. (iv) Contractor shall provide the complaint register and complaint slip serially numbered in duplicate as per sample. The rate of such items included in this items. (v) Any unattended complaints not done in specified time limit. The contractor shall penalty Rs. 200/- on each complaints per day. (vi) Docket shall be taken from MES complaint cell at every morning at 09.00 am by rep of contractor and submitted at complaint cell on nexr morning at 08.45 am after satisfactorily completion on daily basis.

Supply only in replacement switch piano type 5 Amps one way AC 230 Volts.

Supply only in replacement switch piano type 5 Amps two way AC 230 Volts.

Supply only in replacement of bell push 5 Amps, AC 230 Volts.

Supply only in replacement switch/socket combination outlet 3 pin 5 Amps flush type (Multi purpose) piano type AC 230 Volts.

Supply only in replacement switch/socket combination outlet 2 in 1, 3 pin 5 Amps and 15 Amp flush type (Multi purpose) piano type AC 230 Volts.

Supply only in replacement of electronic dimmers, 450W, 250V flush type on the exiting phenolic laminated sheet etc. as reqd.

Supply only in replacement of stepped type electronic fan regulator, flush type on the exiting phenolic laminated sheet etc. as reqd.

Supply only in replacement switch modular type 6 Amps one way AC 230 Volts.

Supply only in replacement switch modular type 16 Amps one way AC 230 Volts.

Supply only in replacement modular type bell push 6 Amps, AC 230 Volts.

Supply only in replacement modular type socket 6 Amps 2/3 pin combined, AC 230 Volts.

Supply only in replacement modular type socket 6/16 Amps 2/3 pin combined, AC 230 Volts.

Supply only in replacement modular type fan regulator, AC 230 Volts.

Supply only in replacement modular white cover plate with frame, 2 module.

Supply only in replacement modular white cover plate with frame, 4 module.

Supply only in replacement modular white cover plate with frame, 8 module.

Supply only in replacement of ceiling rose 65x50mm two to three terminal AC 230 volts complete all as specified.

Supply only buzzer,AC, 230 volts, single phase.

Supply only bell, ding dong, AC, 230 volts, single phase.

Supply only bell multi music type AC, 230 volts, single phase.

Supply only in replacement lamp holder insulated body with back plate batten/angle type for batten fittings.

Supply only in replacement sheet metal enclosures with plug socket single pole and neutral with two pin and earth plug and with one MCB of 20 Amps (SP) complete all as specified.

Supply only in replacement of 30 Watt invertor LED street light fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08, including coneecting up with 2/3 core flexible coppper conductor cable, compete all as specified and directed by Engr-in-Charge.

Supply only in replacement cable flexible PVC insulated twin core with copper conductor of size 23/0.0076

Supply only in replacement cable flexible PVC insulated twin core with copper conductor of size 40/0.0076

Supply only in replacement plug top 3 pin 5 amps AC 230 volts.

Supply only in replacement plug top 3 pin 15 Amps AC 230 volts.

Supply only PVC connector block two ways AC 230 volts suitable for fan/tube light fittings etc.

Supply only bakelite sheet not less than 3mm thick for mounting of switch sockets, fan regulators, etc. size 100x100mm or PVC rectangular Box of 100 mm x 100mm and 50 mm deep complete with screws and washers, etc. all as specified and directed by Engr-in-Charge.

Supply only bakelite sheet not less than 3mm thick for mounting of switch sockets, fan regulators, etc. size 175x100mm or PVC rectangular Box of 175 mm x 100mm and 50 mm deep complete with screws and washers, etc. all as specified and directed by Engr-in-Charge.

Supply only bakelite sheet not less than 3mm thick for mounting of switch sockets, fan regulators, etc. size 250x200mm or PVC rectangular Box of 250 mm x 200mm and 50 mm deep complete with screws and washers, etc. all as specified and directed by Engr-in-Charge.

Supply only bakelite sheet not less than 3mm thick for mounting of switch sockets, fan regulators, etc. size 200x150mm or PVC rectangular Box of 200 mm x 150mm and 50 mm deep complete with screws and washers, etc. all as specified and directed by Engr-in-Charge.

Supply only bakelite sheet not less than 3mm thick for mounting of switch sockets, fan regulators, etc. size 350x300mm or PVC rectangular Box of 350 mm x 300mm and 50 mm deep complete with screws and washers, etc. all as specified and directed by Engr-in-Charge.

Supply only in replacement MCB SP, 6 to 32 Amps 10 KA single pole AC 230 volts complete all as specified

Supply only in replacement MCB SPN 6 to 40 Amps 10 KA AC 230 volts complete all as specified

Supply and fixing brass/copper thimble (lugs) bottle type suitable for MCBs with sub circuit wires complete all as specified

Supply only in replacement of rigid non metalic PVC conduit conduct including junction boxes terminal, tees bends, elbows reducers, bell mouth tube ends and fixing accessories such as complete, lock nuts, saddles pipe hook etc of size 20mm dia. complete all as specified and directed by Engineer in charge.

Supply only in replacement twin sub main cable with PVC conduit 2 x 4 Sqmm multistrand PVC insulated unsheathed copper conductor PVC cable including contineous earth wire 1 x 4 Sqmm copper conductor insulated unsheathed complete all as specified and directed by Engineer in charge.

All as per above item No. 119.00 here- in- before but In PVC casing caping

All as per srl item No.119.00 here in before but PVC conduit 2 x 6 sqmm copper cable as a sub main and 1 x 6 sqmm cable as a earth lead complete all as specified and directed by Engineer in charge.

All as per above item No. 119.00 here- in- before but In PVC casing caping.

Point wiring with 1.5 Sqmm (nominal area) copper conductor cable (Multi strand) PVC insulated and unsheathed in and incl PVC casing caping of adequate size with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan /05 amp socket /bell controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multi strand) PVC insulated and unsheathed with colour code earth wire to common earth dolly complete all as specified.

All as per srl item No 123.00 here in before but with 2.5 sqmm copper conductor cable (multistrand) complete all as specified and directed by Engineer in charge.

Supply only 20 Watt LED Tube Light (4 feet) Ultra bright, (single side connection) with very high efficacy & THD <15% best suited for installation in existing tubelight luminaire with G13 lamp holders to give glare free light.

Supply only in replacement of LED Batten 1x 20W, 220V, AC, with driver, holder excluding LED tube light mounted on square box of suitable size connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply only in replacement of sheet metal enclosure (Factory made) double door shutter type for distribution board (when MCBs are to be used) single pole and neutral 240 volts 8 way with 200 Amps rated busbar all as specified

All as per srl item No. 127.00 here in beflore but 4 way SPN with 200 amps rated bus bar all as specified

All as per srl item No. 127.00 here in beflore but 4 way TPN 415 volts all as specified

Supply only in replacement MCB TPN, 415 Volts, 63 Amps all as specified.

Supply only in replacement PVC casing caping and fixing accessories such as complete, lock nuts, saddles hook etc of adequate size complete all as specified and directed by Engineer in charge.

Supply only in replacement of 20 Watt LED 6500 K (PRIDE PLUS) inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours mounted on square box of suitable size connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing in replacement spring loaded rotary type bipin holder suitable for LED tube light fittings.

Supply only in replacement invertor LED lights fitting 1x 10W (2 Ft), 220V, AC, LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8-10 hours and back up time upto 4 hours., mounted on square box of suitable size including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply only LED luminaire invertor 600 x 600mm, 36 watt, 220 volts AC recessed/ surface type fittings, epoxy powder coated CRCA sheet housing with electronic driver, connector block, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply only invertor LED lamp 9 watt capacity complete all as specified and directed by Engineer-in-Charge.

Supply only invertor LED lamp 12 watt capacity complete all as specified and directed by Engineer-in-Charge.

Supply only in replacement of 25 Watt LED streetlight fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08, including coneecting up with 2/3 core flexible coppper conductor cable, compete all as specified and directed by Engr-in-Charge.

Supply only in replacement of invertor LED round shape 15 watt 220 volts AC recessed type with high efficacy PMMA diffuser soft glare free light complete with drivers, clamps and suitable size as per ground requirement complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply only in replacement of invertor LED bulkhead 10 watt 220 volts AC with high efficacy PMMA diffuser soft glare free light complete with drivers, clamps complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Taking down and dismantling of ceiling fan, segregation of unserviceable parts, cutting and removing out copper winding, cleaning the armature, rewinding of fan armature with appropriate gauge of super enamelled copper wire with necessary insulating materials such as vertex paper, cotton tape, PVC insulation tape, Rotter soft etc varnishing with approved grade of insulation varnish and heating up, re-assembling the fan complete with replacement of unserviceable spares parts, (spare parts will be measured & paid separately) including necessary lathe work for fixing of bush/bearing greasing the same with approved grade of grease, making all electrical connection and including supply and fixing the following items (Split pin - 02 Nos, Connection block - 1 No and Insulation rubber bush. - 01 No) and including necessary transportion to workshop, for following sweeps of ceiing fan of 1200 mm sweep.

Taking out defective capacitor and supply and fix new capocitor of 2.5 MFD 230 volts with conector(capacitor holder with nut) including PVC clamps nuts , as approved make for various make of ceilling fan complete all as specified as directed.

Taking out defective capacitor and supply and fix new capocitor of 4 MFDas approved make for various make of exhaust fan complete all as specified as directed.

Taking out worn out gun metal bush and supply and fix new gun mettal bush for various make of ceilling fan of size 1200 to 1400 mm sweep complete all as specifide and as directed (Make - MSP or eqvt as approved by GE).

Supply and fixing in replacement of bearing for ceiling fan (Bearing No.6201 Z Type).

Supply and fixing in replacement of bearing for ceiling fan (Bearing No.6202 Z Type).

Supply and fixing in replacement of bearing for ceiling fan (Bearing No.6203 Z Type).

Supply and fixing in replacement of bearing for ceiling fan (Bearing No.6204 Z Type).

Repair to Table peg (FD-25/236/277/384) as under :-

Removing broken/unserviceable top of table peg and providing new top of size 450 mm x 300 mm made out of 18 mm pre-laminated particle board including PVC beading around the table top and fix with necessary screw to frame complete all as directed by Engineer-in-Charge

Removing unserviceable/broken legs of peg tables and supply and fix new legs made out of 1st class HW (Indian teak) made to shape and size duly French polished and fixed with glue and bamboo pin all as specified and directed by Engineer-in-Charge.

All as per items ser No. 149.02 above but front/back/side rails of peg tables.

Repair to Table Centre (FD-235/274) :-

Removing the UNSV/Broken top of table centre and providing new top of size 900 mm x 450 mm made out 18 mm thick pre-laminated particle board including 4 mm thick teak beading around the table top complete duly French polished and fixing with necessary screws to frame all as specified and directed by Engineer-in-Charge.

Removing unserviceable/broken legs of table centre and supply and fix new legs made out of 1st class HW (Indian teak) made to shape and size duly French polished and fixed with glue and bamboo pin all as specified and directed by Engineer-in-Charge.

All as per items ser No.150.02 above but front/back side rails of Centre table.

Repair to chair Varandah FD/MAP-II/06 & 15 as under :-

Removing old UNSV/Broken PVC seat & Back from chair varandah & providing and fixing new PVC Seat & Back for chair varandah all as specified on drawing and as directed by Engr-in-Charge.

Repair to Almirah large steel (FD-67 and 1031) as under :-

Removing of UNSV 3 way locking device and providing / S&F of new locking device 3 way and fixing them to almirah large and making original shape complete welding to the almirah all as specified on drawing and directed by Engineer-in charge.

Removing of UNSV hinges from shutters S&F of new hinges 75mm by welding properly to the shutters all as specified on drawing and directed by Engineer-in charge.

Removing of unserviceable locks and providing new locks of size 50 mm, 6 levers with stainless steel keys in duplicate for Almirah large steel with shelves and fixing them with existing 3 way locking system all as specified on drawing and directed by Engineer-in charge.

Removing of unserviceable / broken handles & providing new handle steel cromium plated 100mm to almirah large with shelves & fix suitably as specified on drawing and directed by Engineer-in charge.

Removing unserviceable shelves of almirah large steel with shelves and providing new shelves, made out of 20 guage MS black sheet duly painted with two coats of synthetic enamel paint over a coat of redoxide primer by means of spray painting & providing necessary cleats/nuts and bolts etc complete all as specified on drawing and directed by Engineer-in charge.

Repair to Almirah med steel (FD- 243 and 1032) as under :-

Removing of UNSV 3 way locking device and providing / S&F of new locking device 3 way and fixing them to almirah med and making original shape complete welding to the almirah all as specified on drawing and directed by Engineer-in charge.

Removing of UNSV hinges from shutters S&F of new hinges 75mm by welding properly to the shutters all as specified on drawing and directed by Engineer-in charge.

Removing of unserviceable locks and providing new locks of size 50 mm, 6 levers with stainless steel keys in duplicate for Almirah med steel with shelves and fixing them with existing 3 way locking system all as specified on drawing and directed by Engineer-in charge.

Removing of unserviceable / broken handles & providing new handle steel cromium plated 100mm to almirah med with shelves & fix suitably as specified on drawing and asdirected by Engineer-in charge.

Removing unserviceable shelves of almirah med steel with shelves and providing new shelves, made out of 20 guage MS black sheet duly painted with two coats of synthetic enamel paint over a coat of redoxide primer by means of spray painting & providing necessary cleats/nuts and bolts etc complete all as specified on drawing and directed by Engineer-in charge.

Repair to Bed Hard steel MAP (FD/E6/MAP/08)

Removing the existing worn out UNSV Ply wood from Bed Hard steel MAP as per drg & directed by Engineer -In -Charge.

Supply and fixing of ply wood commercial of size 7' x 3' x 12'mm thick BWR grade, Ist mark kit ply (Vista) / Assam power / Anchor on top frame with counter sunk screw with washer of required length all as specified and as directed by Engineer - in-Charge.

Removing of old UNSV Head Rest from Bed Hard Steel MAP and S & F New Head Rest as per existing size and Shape all as specified as per drawing and directed by Engineer-in charge.

Removing of old UNSV Foot Rest from Bed Hard Steel MAP and S & F New Foot Rest as per existing size and Shape all as specified as per drawing and directed by Engineer-in charge.

Table computer (FD/E6/MAP/03)

Removing unserviceable / Broken top of table computer and providing new top of same size made out of 18mm thick pre-laminated particle board including PVC beading alround the table top, duly french polished as directed & as shown on Drg.

Removing unserviceable / Broken Key Board Drawer and S & F of New one as per existeing size all as specified on drawing and as directed by Engr-in-Charge.

Removing unserviceable / Broken Drawer with knob and S & F of New one as per existeing size all as specified on drawing and as directed by Engr-in-Charge.

Repairs to bed Ply wood top/Bed Newar (FD-245/246/247) as under :

Taking down UNSV head board complete from the bed and S/F new head board made out of 1st class HW duly french polished on both side of head board all as specified and shown in Drg.

All as per item Nos.156.01 above but for foot board of bed.

Removing of old unserviceable worn out ply wood top and batten from bed hard and supply and fix new batten 900 mm long of size 15 x 40 mm and ply wood 12 mm thick BWR grade commercial ply wood of required size fix with screws and polishing complete bed after repair to all schedule as specified and directed by Engineer-in-Charge. The ply wood shall be in single peace as per drg No-FD-246/247.

Repair to sofa set 4 seater and 5 seater (FD-373) as under :-

Repair to sofa set 4 seater FD-373 by removing old unserviceable seat & back by replacing with new foam/cushion, 40 density 100 mm tapestry as specified and shown in drg (Rate of Tapestry shall be not less than Rs 200/- per mtr)

All as per item No. 157.01 above but sofa set 5 Seater (FD-373)

Repair to table dining 6/8 pers (FD-239/376)as under :-

Removing UNSV worn out top of table and S&F new top made of 18 mm thick pre-laminated particle board of size 1500 x 900mm including 4 mm thich 1st class hard wood teak edging all round of table top complete all as specified and shown in drg for 6 Pers

Removing UNSV worn out legs of table and S&F new legs made out of 1st class HW (Indian Teak) made to shape and size as per drg duly French Polished, fixed with glue and bamboos pin complete all as specified & shown on Drgs (for table 6 persons)

M&L for scrapping of old paint & applying putty and making smoothing of surfaces complete before painting and applying one coat of red oxied (Steel primer) & two coats of synthetic enamal paint of olive green by spray painting of the following steel furnitures. These shall be carried out in offrs/JCOs/ ORs md accn, Offices and unit lines at AOP & NRC areas and BSO Furniture yard under GE NRC:

Almirah Large steel

Almirah med Steel

Prepairing of smooth surfaces by scraping/sand papering and applying two coats of french polish of superior quality to the following wooden items of furnitures. These shall be carried out in offrs/JCOs/ ORs md accn, Offices and unit lines at AOP & NRC areas and BSO Furniture yard under GE NRC.

Bed Plywood top (FD-246 & 247)

Chair dinning (FD-16/228/279)

Chair Dining FD Coushioned (FD/E6/MAP/10) (FD/MAP-II/04)

Table writing (FD249,275/DB 3962/3877)

Table dinning 6 pers/8 pers (MAP) FD-239/273 FD/E6/MAP-II/03

Table centre (FD-235/274)

Peg Table (FD-236/277 )

Sofa set 4 seater ( FD-373 )

Sofa set 5 seater ( FD-373 FD/E6/MAP-II/02)

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 74,261.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

VISHAL CONSTRUCTIONS

M/S MK Nair

Bidder Name

SVT ENGINEERS AND CONTRACTOR.

M/S MK Nair

VISHAL CONSTRUCTIONS