ALTERATION/RENEWAL/MAINT OF DAD GUEST HOUSE/TRANSIT FACILITIES AT LEKHANAGAR CDA JABALPUR AND PROVN OF CONCERTINA COIL SECURITY FENCING OVER THE FRONT PORTION OF THE EXISTING BOUNDARY WALLS OF KV CMM UNDER AGE B/R-I OF GE (EAST) JABALPUR

Amount

Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water etc and removing the rubbish to a distance n'exc 100 mtr at low laying area complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surface in CM 1:4 on fair faces of mixed with WPC as per manufacturer’s instructions, but not less than 3% by weight of cement finished of concrete surfaces even and fair without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid separately

Supply only Integral water proofing compound (ISI Mark) all as specified and directed.

S&F aluminium composite panel cladding with open grooves for linear as well as curviliner portions of the building / wall for all heightand all levels, including scaffolding etc including (a) Providing faabricating and supplying and fixing panels of aluminium composite penel cladding in pan shape in metallic colour or approved shades out of 2 mm thick aluminium composite panel material with core sandwiched between two aluminium sheets (each 0.25 mm thick). The aluminium composite panel cladding sheet shall be oil coated with kynar 500 based PVDF/ Lumiflon based fluoropolymer resin coating of approved color and shade on face No1 and polymer (service) coating on face No.2 as specified using stainless steel screws nuts bolts washer cleats weather silicone sealant backer rods etc (c) The fastening brackets of aluminium alloy 6005T5/MSwith Hot clip galvanized with serrations and serrated washers to arrest the wind load movement fasteners SS 316 pins and anchor bolts of approved make in SS 316 Nylon separators to prevent bi-metallic contacts all complete requirement as per specification of manufacturer complete all as directed.

S&F Anodosed aluminium frame for channel clear angle or other section complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified.

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying White cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

M&L forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Demolition of brick work built in cement mortar including all quoins, arches etc complete all as specified and directed.

M&L Brick work with sub class 'B' old size bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) and removing rubbish to a distance n. exc 50m at low laying area complete all as specified.

M&L machine cut kota stone slab flooring 20-25 mm thick over and including cement screed bed or bedding layer of cement mortar 15 mm thick in CM 1:6 for laying floor finishes laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all specified and directed.

All as per item No 12 but in skirting and daddo including rendering 10 mm thick Cement mortar (1:4) complete all specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thick ness, M-35 Grade with Grey cement and using coloured pigment laid over 50 mm thick sand cushioning complete all as specified.

M&L 50mm thick sand cushioning for paver block complete all as specified and directed

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed With grey cement pigment and pointed in neat cement slurry in floors.

M&L 75mm thick PCC (1:3:6) type C-2 (40mm graded stone aggregate) as in sub base of flooring complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2, using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish to a distance nexc 50mtr at low lying area complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors laid over & including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to matchwith the shade of tiles all as specified and directed.

All as per Item srl No 20 above but Vertical surface all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.11 sqm but nexc 0.18 sqm,in floors,laid over & including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified.

M&L Glazed ceramic tiles 300×450×7 mm thick (coloured) on vertical surfaces such as dado, skirting and rise to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match to the shade of tiles over and including 10 thick rendering in CM (1:4) finished rough to receive tiles etc complete all as specified and directed.

M&L 25 mm Thick PCC 1:2:4 Type B-1 (using 20 mm graded aggregate ).without using extra cement finishing cement concrete surface even and rough all as specified and directed.

M & L 20mm Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite completed .all as specified and directed.

M&L for frame work as in doors or gates of angle or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other coverings, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5.Sqm & not exc 4 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n .exc 1.5.Sqm each complete all as specified and directed.

S&F Solid PVC Solid door frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing .

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core supplying & fixing in frame at site as per specification & drawing.

S & F aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long.complete all as specified and directed.

S&F aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long.complete all as specified and directed.

S&F extruded aluminum alloy handles, fabricated type, anodized 150 mm long.complete all as specified and directed.

S& F Butt hinges, medium weight, cold rolled mild steel and fixed 100 mm long.complete all as specified and directed.

S&F vitreous China wash basin, white, flat back, size 580x450mm excluding taps, chain and plug and porcelain stopper but including brackets, waste pipe. complete all as specified and directed.

S&F in repairs 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed. complete all as specified and directed.

S&F in repairs 15mm dia bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

Same all as Item Srl No 38 above but 20 mm complete all as specified and directed.

S&F 15mm bore GI tubing medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

Same all as Item Srl No 40 above but 20mm bore complete all as specified and directed

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, excluding flushing cistern, flush pipe etc but including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel as fixed.complete all as specified and directed.

S & F 10 ltrs capacity PVC flushing cistern, low or high level, with inlet, ball valve, syphonic action type, float and handle, pull or push type including brackets complete all as specified and directed .

S&F 15 mm dia stop valves/angle cock, cast copper alloy fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. complete all as specified and directed.

PVC (SWR) floor trap 75mm, with grating including jointing with solvent cement.complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Cutting opening in cement concrete walls (any descript-ion) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. complete all as specified and directed.

Taking down existing treatment including loose surface scraping with scraper chiseling scarping of surface with wire brush or any other method and removing the scrapped materials debris to a distance n.exc 50m depositing where directed complete all as specified.

M & L for 10mm thick rendering in CM 1:4 finished even and smooth as in roof mixed with water proofing compound as per manufacturer instruction by wt of cement brick or concrete all as specified and directed.

M&L for preparation of surface including cleaning, drying and removing all oil, grease, dust etc and priming the surface with a coat of Dr. Fixit primeseal apply at the rate of 8-10 Sqm/Ltr and applying two coats of Dr. Fixit Hydroshield PUD plus by brush or roller to achieve a total depth of 0.8 - 1mm with coverage of approximately 0.60 Litre/Sqm per coat. Note : (i) The contents of Dr. Fixit Hydroshield PUD plus shall be thoroughly stirred for at least 2 - 3 minutes using a slow speed (300-400 RPM) drill machine attached with a mixing paddle. Do not dilute with water. Keep on stirring during application. (ii) All joints corners/drainage outlets and penetration points shall be treated prior to all application of Dr. Fixit Hydroshield PUD plus. All corners, gaps, joints, protrusions and outlets should be coated with an extra coat incorporating reinforcing fabric. (iii) Allow complete drying between coats with a minimum 3 to 4 hours depending on the weather conditions.

Dismantling water tank exc 500 and n.ext 1000 ltr capacity water tanks complete all as specified.

S&F 1000 ltrs rotational moulded polyethylene water storage tanks (cylindrical vetical with threaded closed top) hoisted and fixed in position all as specified in SSR Part-I. Note : PVC tank shall be ISI marked and having two layers.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (minimum weight 15mm-142gms/20mm-210gms./25mm-455gms/40mm-690gms) complete all as specified and directed

M&L for excavation in post holes (or similar holes) each not exceeding 0.50 Cum meter in any type of soil, getting out, returning filling in watering and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm and removing surplus soil to a distance n. exc 50 mtr and making good surface complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate in foundation filling and mass concrete etc surrounding posts complete all as specified and directed.

S&F punched tape concertine coil 600 mm coil dia size of any type of standards, rails etc including provision of mild steel (annealed) binding wire complete all as specified and directed.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165.

S&F galvanized, 2 strand, steel barbed wire 2.24 mm dia, barbed with w mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild wire, stable or steel pins, etc complete all as specified and directed (each line wire to be measured).

M&L preparation of new or previously untreated surfaces of steel and iron surfaces exc 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Schedule of credit amount of Rs. 22,894.00 to be deducted during AOC

MAYANK CONSTRUCTIONS

DOBARIA BUILDCON

M/S BHARTI ENTERPRISES

M/S RAJ BUILDERS

R R VISHWAKARMA CONSTRUCTION CO

M/s Ram Associates