REPAIR TO LEAKAGE/ SEEPAGE, WATER TANK, PLUMBING FITTINGS, CHAJJAS, BEAMS, COLOMNS, CONNECTED ITEMS, FLOORING, SANITARY AT MD AND OTM ACCN AT K AREA AND SF ACCN SEC 28/29D UNDER GE CHANDIGARH.

Amount

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving exc. 15cm thick (above G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for, Complete all as specified and as directed.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description not exc 1 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Dismanntling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering etc complete all as specified and directed.

Dismantling Plain or corrugated fibre sheet etc any gauge, thickness, complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (up to 4th storey of building) complete all as specified and directed by Engr-In-Charge.

Cutting channels, grooves or rebates 75 mm wide and 65 mm deep and making good in cement mortar 1:3 after inserting APP membrane complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 250 & n.exc 500 ltr in capacity complete all as specified

Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 500 & n.exc 1000 ltr in capacity complete all as specified

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 250 & nexc 500 ltr), Complete all as specified and as directed

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 500 & nexc 1000 ltr), Complete all as specified and as directed

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Dismantling existing brick tiles or terracing tiles, single layer on roofs from any position grouted in cement mortar including removal of any existing treatment complete all as specified and directed by Engineer in Charge.

Dismantlling Mud phuska in roofs, any thickness,including plastering and leeping (whether full thickness removed or only a part thereof) in any position including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer in Charge.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying and fixing in repairs 15 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 20 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Repairing the edges of concrete chajjas, facias, slabs, columns & the like by providing PCC (1:2:4) type B-0 including all necessary form work and rendering 15 mm thick (average thickness) in cement mortar (1:3), after applying a coat of cement slurry @ 3 kg/ Sq. m of surface, finished even and fair, surface area not exceeding 450 mm wide, in patches including taking down swoolen/damaged plaster or concrete complete all as specified.

Plain cement concrete (1:7:12) type D-2,using 40 mm graded stone aggregate as in sunken floor etc complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in cement concrete in roof kerbs, roof padding or mud stops, back filling of chowkats, coping, bed plates rounded or chamfered on edges with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates,back filling in steel door frame etc, using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.

40 mm thick Cement concrete (1:2:4) type B-1,using 20 mm graded mechanically crushed stone aggregate as in flooring etc. complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .

Plain cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) in blocks for fixing hold fasts & pressed steel frames for doors including necessary form work complete all as specified and directed.

Plain cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in surface channels & drains including forming the finished drain using extra cement using forms, mould etc complete all as specified and directed.

75 mm thick, cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in sub base finishing the surfaces even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L glass dividing strips 3 mm thick width of strips 38mm and inserted in position to confirm to design.

Reinforced Cement Concrete Nominal mix ( 1:1.5:3) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 6mm to 8 mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Use & waste of Formwork to edges not exceeding 200mm thick (Horizontal or sloping) and similar works exc 10 cm but n.exc 20 cm wide. , complete all as specified and directed by Engineer-in-Charge.

Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles double charged dark shade 10 mm thick (Square/rectangular) polished, area of each tile exceeding 0.36 Sqm, in floors/skirting etc. laid and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15mm thick bedding of layer of cement sand mortar (1:6) complete all as specified and as directed.

Glazed ceramic coloured tiles 600 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 complete all as specified and directed by Engineer-in-Charge.

Rubber coated Chequered cement concrete tiles 300mmx300mmx25mm thick with grey cement and pigment, over and including 15 mm thick screed in Cement mortar 1:6 set jointed and pointed in neat cement slurry in floors complete, all as specified and as directed by Engineer-in-Charge.

Grey coloured PCC factory made tiles, ISI marked, 25 mm thick of size 250 mm x 250 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & pigments. over and including 20 mm thick screed bed in cement mortar (1:4) mixed with and including WPC as per manufacturers instruction ,bedding joints grouted flush in cement mortar (1:3) complete all as specified and directed by Engineer-in-Charge.

M&L out door/parking tiles heavy duty for high traffic non skid, anti scratch, heavy grip, vitreous/semi vitreous coloured, unique designs tiles 8 to 10mm thick area of each tile of size 300mmX300mm, in floors, parking/outdoor tiles etc. fixed with 3 mm spacer & filled with grout breaking strength not less than 1700N as in floorset and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM(1:4), complete all as specified and directed.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

80mm thick machine pressed precast concrete ( M-40 grade) prepolished rubberized moulded interlocking paver block manufactured in an automatic plant working on vibration and simultaneous hydraulic compression from top, with grey cement and pigment(Yellow & red) any shape and size confirming to IS 15658-2006 laid over and including 50 mm thick cushion of coarse sand & filling the joints after laying complete all as specified and as directed.

60mm thick machine pressed precast concrete ( M-35 grade) prepolished rubberized moulded interlocking paver block manufactured in an automatic plant working on vibration and simultaneous hydraulic compression from top, with grey cement and pigment(Yellow & red) any shape and size confirming to IS 15658-2006 laid over and including 50 mm thick cushion of coarse sand & filling the joints after laying complete all as specified and as directed.

GI spout pipe 50 mm dia 600 mm long fixed in PCC 1:2:4 complete all as specified and directed by Engineer-in-Charge.

Brushing neat cement slurry with 3.0 kg of cement per sq mtr complete, all as specified and as directed by Engineer-in-Charge.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m over cleaned and dry roof surface including parapet etc complete, all as specified and as directed by Engineer-in-Charge.

M&L providig protection layer applying 15 mm thick cement plaster in cement mortar 1:4 (cement :coarse sand) mixed with water proofing compound @ 200 ml per 50 kg cement bag all as specified & directed directed.

Water proofing roof treatment using APP polymeric ( on roof/sunken portion) water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Rendering 10 mm thick in cement mortar 1:4, on roof surfaces including flashings and junction of parapets,brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new external surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 litre/ 10sqm over new surfaces as per manufacturers instructions etc complete all as specified and directed by Engineer-in-Charge.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1 mm wall care puty including preparation of surface complete all as specified and directed.

Complete removal of existing treatment,preparation of external surfaces of walls brooming down, applying one coat of white cement based wall care putty after applying emery paper or sand paper and two coats of weather proof exterior emulsion paint(Ist quality) Apex over a coat of primer as per manufacturers instructions etc complete (up to 4th storey of building) all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing surface and applying two coats of oil bound distemper over and including a coat of primer and 1 mm wall care puty on wall surfaces (upto 4th story of bldg), complete all as specified and as directed.

Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings complete all as specified and directed by Engineer-in-Charge.

Preparation of old plastered surfaces of wall and applying one coat of oil bound distemper (Ist quality) on walls including preparation of surface complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying one coats of cement base paint on walls including preparation of surface complete (up to 4th storey of building) all as specified and directed.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for one coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

M&L for one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engineer-in-Charge.

M&L for factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube of top and bottom rails.MS frame shall be covered with heat maulded prelaminated PVC "c" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and prelaminated PVC sheet for top rail ,lock rail & bottom rail on either side & as gap insert for top and bottom rail. Pannelling of prelaminated PVC sheet to be fitted in MS frame welded /sealed to the stiles & rails with suitable PVC sheet bedding and jointed together with solvent cement as per specification and drawings all as specified and as directed.

35 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match supplied and fixed complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars and without glazing bars (Double shutter ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Factory made box type steel ventilator with top hung or fixed half glass and half wire mesh portion shutter including projecting type hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.Note:Sheet glass and wire gauge will be measured and paid separately against respective items

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

S&F aluminium grills size exc. 4mm x 4mm and aperture n.exc. 80mm including. fixing with aluminium Y channel, 1.20mm thick with steel screw complete all as specified and as directed.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel 100 mm Butt hinges, hinge pin, anodised and fixed, type C-21, Complete all as specified and as directed

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

150 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm complete all as specified and directed by Engineer-in-Charge.

S&F mild steel helical door spring MS 300mm long ordinary rat tail pattern spring including roller & roller plate complete fixed to wooden/steel chowkats complete all as specified and directed by Engineer-in-Charge.

S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete fixed in reapir all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing wwith silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 5.5 mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 5.5 mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

S&F Mild Steel work as in wind ties etc. conforming to Fe-290 Gde- E-165 all as specified and directed.

M&L mild steel work in framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, Fe-410-W (Gde E-250) complete all as as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminum zinc coating profile sheet GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed.

M&L 2 mm thick Fibre glass reinforced transparent plain/corrugated sheeting of white or any colour fixed with coach screw and washer in roof, wall etc complete all as specified.

S&F 18/19 mm HDHMR board exterior grade, prelaminated both side with 1mm thick decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in kitchen cabinets,cupboards complet all fitting jointing etc complete all as specified and as directed.

M&L Particle board,18/19 mm thick medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work including PVC beading as in cub board shelves/cabinet works complete all as specified and directed.

M&L Particle board 25mm mm thick medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work including PVC beading as in cub board shelves/cabinet works complete all as specified and directed.

M&L Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. (Sample as approved by Garrison Engineer).

PVC hollow wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site complete all as specified and directed

9 mm thick PVC prelaminated Gypsum board ceiling including anodised aluminium snap grid framework for ceiling having grid size 605 x 605 mm comprising of wall angle of size 25 mm x 25 mm x1.3 mm,main runner of size 38 mm x26 mm x1.3 mm.The grid system will be suspended at every 1200 mm c/c in both directions by using 3.5 mm dia aqualine wire fixed to purlins or RCC roof with suitable fastener to with stand the load of grid system with ceiling board as per manufacturers instructions complete all as specified and as directed by the Engineer-in-Charge.

S&F Stainless steel finish zinc chrome handle, fancy type, curve design, 144 mm size and fixed in position with stainless steel screws, ISI marked, suitable for rubber wood shutter drawer(s), complete as per the sample kept in the office of Engineer-in-Charge.

S&F Stainless steel auto close (dada) hinges suitable for moulded shutter fixed in position with stainless steel screws, complete all as specified and directed.

S&F in repair 50 mm long magnatic catcher of brassalloy body superior quality and fixed with screw complete all as specified.

S&F in repair telescopic channel/slider to fiacilitate drawer slide on steel ball bearing 400-500 mm long and fixed in position with stainless steel screws , ISI marked , suitable for cupboard drawers , complete as per the sample kept in the office of Engr-in-charge

Supply and fix in repairs aluminium mortice lock, vertical type size 100mm, 2 lever complete all as specified and directed.

S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat cover white with stainless steel L-type jet spray with 1 m hose pipe, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap with connection complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F for vitreous china white wash basin with flat back of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.

S&F table top wash basin Vitreous China of size (600mm x 450mmx150mm), excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand bottle trap s/s etc. as in repairs complete all as specified and as directed.

S&F single piece WC of size 365x655x765 with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

S&F in repair 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass chromum plated 3 way wall mixer with including telephonic shower for mixing hot and cold water fancy type with screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F for centre hole basin mixer (swan neck) 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed as in repair complete all as specified and as directed.

S&F for wall mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe with L bend incl (provn for Over Head shower) ,and fixed as in repair complete all as specified and as directed.

S&F for Sink mixer (swan neck) 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.

S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm bore iron pipe as in repair complete all as specified and as directed.

S&F in repairs 2 way Pillar cock single lever of 450mm long fancy type , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap two way brass with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs concealed stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

S&F Swivel shower of CP with shower arm 15mm size,125 mm long with bend of 45 degree with flange of PTMT any colour for fixing with 15mm pipe (Minimum weight 40 gm) IN REPAIR, complete all as specified.

S&F in repairs Brass chromium plated overhead shower of size 150x150mm with shower arm 450mm long with flange, with swivel joints, any size, fixed to 15mm bore CPVC pipe, fixed in repairs, all as specified and as directed.

S&F in repairs toilet paper holder chromium plated with fixing to wall complete all as specified and directed.

S&F in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed

S&F in repair Sheet glass shelf assembly consisting of 5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as complete.

S & F sinks made of stainless steel1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with adequate shelves and sections Heavy gauge wall mounted with fitting screws,complete all as specified.

S&F as in repair Sink with drainage board made of stainless steel of wall thickness 1mm thick for kitchen or laboratory with plug, washers and wastes, including bedding in cement sand mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm including waste pipe of suitable dia complete all as specified and as directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105 gms) for WHB complete all as specified.

S&F in repair Waste coupling of PTMT, for WHB any colour half or full threaded suitable for 32 mm size discharge pipe (Minimum weight 45 gm) , complete all as specified.

S&F in repair urinal waste pipe 32mm dia, 800mm long with cup and nuts fixed to urinal complete all as specified & directed

S&F for CP soap dish holder in repair of complete all as specified and as directed.

S&F for PVC connections with PTMT nuts of length 600 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

S&F in reapir Cast iron 'P' or 'S' trap, ISI marked, suitable for 100 mm bore CI spun pipes complete all as specified.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings (brass & plain) on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings (brass & plain) on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 UNION fittings, ISI marked for CPVC pipe outer diameter 25 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 25 mm bore complete all as specified and directed by Engineer-in-Charge.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 1,43,403.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

M/s Super Trading Corporation (BID ID -3369373)

Baba Engineers and Contractors (BID ID -3368859)