Construction of Additional Urban Primary Health centre at Madasamy kovil Street in RajapalayamMunicipality

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum

Column Footing

Grade Beam

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain cement concrete 1.4.8 (one cement four sand and eight aggregate) using 40mm ISS HBG metal Including cost and conveyance of all materials and labour charges complete as per Standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38

For Column footing and grade beam

For beams and lintel , slab

for RCC columns

Filling excavatted of excess earth in basement filling with consolitated as per the instructions given by departmental officers including cost of conveyance and all labour charges etc. complete as per SS

Supplying, fabrication and placing in position of steel reinforcement using mild steel (or) ribbed tar steel rods, for all RCC works as per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending & tying etc complete as per standard specification

Plain cement concrete 1:2:4 (one cement two sand and four aggregate) using 20mm ISS HBG metal Including cost and conveyance of all materials and labour charges complete as per Standard specification

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials)

Upto basement

Above basement

Brickwork in Cement Mortar 1:5 mix using III rd Class country bricks of size 8 3/4" x4 1/4" x 2 3/4" including all cost and conveyance of all materials and labour charges etc. complete as per standard specifications.

Upto basement

Above basement

Brick Partition Walls using III class ground moulded chamber bricks of size 8 3/4"X4 1/4" X 2 3/4" in C.M 1:3 using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification - 10 sqm

Supplying and fixing of Granite slabs ( Super fine polished with Machine cut Edges ) of Size 4'x2' and above 18mm 20mm thick -PWD SOR Pno.36 (SL.No.29 (a))

Plastering in Cement Mortar. 1:5 mix 12mm thick and including all material and labour charges etc: complete

Special Ceiling plastering in Cement Mortar. 1 : 3 mix 10mm thick & including labour charges etc complete

Supplying and fixing of MS grills for doors, windows and ventilators as directed by departmental officers including cost of MS grills, red oxide primer one coat and all labour charges etc. complete as per standard specification

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Weathering course with concrete broken brick jelly 20mm size uniform gauge in pure slacked lime (no sand to be added) over the RCC roof slabs in the proportion of brick jelly to lime being 32:12.3 by volume well beaten with wooden beaters for giving required slope and thickness, keeping the surface constantly wet by sprinkling lime jiggery water as per standard specification as directed by the departmental officers

Terrace flooring with hydraulic pressed tiles of size 23x23x2cm laid in CM 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound conforming to IS at 2% by weight of cement used and the top pointed with same mortar mixed with red oxide to the full depth of tiles including cost and conveyance of all materials and labour charges etc. complete as per standard specification

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Supply and fixing of Stainless steel (Salem stainless steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc.

Supplying & fixing door shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Painting two coats over new iron work with ready mixed paint of approved quality and colour including cost of all materials and labour charges, brushes and scaffolding charges etc. complete as per standard specification

Providing cup board shutter using termite /water proof plywood of 19mm thick over which laminated shrrt of 0.8mm thick fixed inside the shutter and 1 mm thick fixed in the outside of the shutter using fevicil, along with necessary furniture fittings ,such us hydralic hinges, tower bolt, handles, multi purpose lock etc, as directed by the departmnetal officers. The design pattern, water proof ply wood ,laminate shaeet and other materials should be got approved from the Executive Engineers before use on Work (PWD SOR- 2021-2022-Pno:43 Item no:124)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Dadooing walls with Glazed tiles of sizes 305mm X 450mm X 8mm size of approved make and quality and colour Set in cement mortar 1:2 (one cement, two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement

Supplying and fixing in position Cement based hydrualically pressed Anti-Skid tiles (pattern design) 20 mmthick in cement mortar 1:3 - 20mm thick & pointed with same colour of cement etc., complete as per standard specification

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Providing rain water harvesting using 3 nos.of RCC well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with RCC circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmneal officers etc., complete in all respects.

Supplying and fixing in position of Indian make bewelled edge mirror of approved quality and brand of size 600 x 450mm with necessary plastic back, PVC frame and bottom stand of approved colour with brass screws,rawal plugs etc., complete complying with std,specification.

Supplying and fixing best approved quality brass C P/AI anodised Towel Rod 600mm long and 20mm diameter with brackets of same materials including cost of Teak - wood plugs and CP screws etc., complete complying with std. specifications.

Wiring with 2x1.5 sq.mm PVC sheathed SC alu Cable of 1100V grade of suitable PVc rigid pipe on wall and ceiling with PVC accessories with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour concealed for light point ( SD-25)

Wiring with 2x2.5 sq.mm PVC sheathed SC alu Cable of 650V grade of suitable heavy guage MS condiuit pipe on wall and ceiling with MS accessories inflush with wall with 150mm x 10mm x75mm MS switch box with 3mm thick hylum sheet cover for 5A 3 pin non internlocking C.S.plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point ( SD-38)

Wiring with 2x4 sq.mm956/0.3) PVC sheathed SC alu Cable of 650V grade of suitable heavy guage MS condiuit pipe on wall and ceiling with MS accessories inflush with wall with 150mm x 10mm x75mm MS switch box with 3mm thick hylum sheet cover for 5A 3 pin non internlocking C.S.plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point ( SD-40)

Wiring with 2x1.5 sq.mm PVC sheathed SC alu Cable of 1100V grade of suitablePVC rigid pipe on wall and ceiling with PVC accessories with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for open PVC Fan point .( SD-25)

Supplying and fixing of 20W 4 Feet LED Fitting with LED ( PWD SOR- 2023-24 Pno.114) Item No. 15 (b)

Supplying and fixing of single box type 4'36 W flu fitting complete with electronic ballast with TW round block on wall and ceiling with PVC unsheathed leads from terminals to the fitting with flu tubes.( SD-87)

Supply and Fixing of 30W LED Outdoor Street Light Fitting with LED (PWD SOR-2021-22) Pno: 115 Item No: 17 (a)

Supplying and fixing of 1200mm ( 48") sweep AC ceiling fan complete with regulator with 1 metre down fan clamp with side plates and cross arm 450mm (18")( SD-110)

Supplying and fixing of 4 way DB of 15A way with 16 Amps DPIC switch of 500 V with fuse and neutral on suitbale angle iron frame work with trunking box, MS cable entry box with PWD Earthing. (SD147)

Supplying and fixing of 8 way MCB of 16A /way with 32A DPIC switch of 500 V with F& N onsuitable angle iron frame work with trunking box MS cable entry box with PWD earthing. (SD 159)

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylem sheet covered TW switch box and 5A FT switch (two way) with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed staircase light point (SD-31)

Supply and run of 4 x 6 sq.mm. (84/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in 32mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains- (SD-73)

Gelogical survey report for conducting and locating borewell with pumpset etc., complete

Drilling of 150mm dia vertical deep borewell in hard rock area to regulated depth as directed by the engineer including labour charges for inserting casing pipe assembly in the drilled borewell if necessary grinding the casing pipe etc., complete as per standard specifications.

Supply and fixing of 200mm dia ( CS) PVC casing pipe as per IS 12818/2010 the rate icluding all cost and conveyance etc complete. TWAD SOR- 2021-22 (Pno.22 ) Item No. 1.1 (Sl.No.1)

Supply and fixing of three phase 3.0Hp (50 X 100) Submersible pumps confirm to IS 8034/2002 and as amended thereafter and BEE 3 star rated capable of discharging noted LPM against head of water column due to all Causes . The pump shall be with stainless steel shaft and dynamically balanced bronze or cast SS impeller , brass screws and CI FG 200 Grade pump /bowl diffuser with ISI Mark. the Pump shall be directly coupled to continous rated two pole suitable wet type vertical squrril cage induction motor as per IS9283/1995 as amended there after ,suitable for Operation in AC three phase 415V+/-10% 50HZ +/-5% (TWAD SOR-2022-23) Pno.98 Iten No. 3.1 ( Sl.No.5)

Supply and delivery of Three Phase Panel Board - Star Delta with two level Guard and auto start suitable for Submersible pumpsets and accessories including all fittings suitable for Submersible pump sets.Panel Board should be provided as per specification. Rates inclusive of Packing, Loading, Freight, Unloading, Stacking, Transit and Insurance charges etc, complete. (TWAD SOR-2022-23) Pno.110 Iten No. 11.1 ( Sl.No.5)

Supplying and fixing of PVC insulated and sheathed 3 core 4.00 sq.mm Flat type Copper cable cofirming to IS 694/ 1990 and including cost and conveyance of all materials to site and labour charges etc, complete as per standard specification. (TWAD SOR-2022-23) Pno.116Iten No. 12.1 ( Sl.No.3)

Labour charges for the erection of 3Hp submersible pump set in bore well/open well including fixing and jointing submersible cable with proper clamps up to the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges up to the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventer, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pump set and trail run for 10 days. (TWAD -SOR-2021-22) Pno.287 Item No. 17c (i)

Supplying and fixing CPVC pipes and Specials of approved quality and brand. ( PWD SOR-2022-23 ) Pno.106, 109,110) Item no: 410 ,413,

20mm dia pipe (410-b)

25mm dia pipe (410-c)

32mm dia pipe (410-d)

20mm dia Elbow (413-I-e)

20mm dia TEE (413-II-e)

20mm dia Coupling (413-IV-e)

20mm dia Union (413-V-e)

25mm dia Elbow (413-I-d)

25mm dia TEE (413-II-d)

25mm dia Coupling (413-IV-d)

25mm dia Union (413-V-d)

32 mm dia Elbow (413-I-c)

32mm dia TEE (413-II-c)

32 mm dia Coupling (413-IV-c)

32 mm dia Union (413-V-c)

Supplying and fixing GM gate valve of approved quality and brand

20mm dia GM gate valve

25mm dia GM gate valve

32mm dia GM gate valve

Supplying and Delivery of Following HDPE and Nylon Ropes

32mm HDPE Hose (1Mpa or 10Kg/M2 Pressure)

Nylon Rope For Borewell

Supply and Delivery of 2000 ltr HDPE Tank as per IS 12701/1996 including laoding unloading , Transportation and labour charges for fixing of the GI pipes and Specials for pipe connection works including cutting, threading and fixing charges etc

Supply and Fixing of Stailess Steel Sink of size 600mm x 450mm x 200mm with 32mm dia 'B' Class GI Waste Water Pipe and 32mm dia CP Waste Coupling (PWD SOR-2021-22 )Page No.50 Item no. 188(b)

Supplying and fixing in position PVC. Nahini trap of various sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly limeconcrete 1:2:5 (one part of lime two parts of sand and moirtar 1:3 (one cement and three sand) including dismandling masonry works wherever found necessary and making good the damaged portions to the originaland giving connections to the cast iron pipe as directed etc., complete, complying with standard specification

Supply and fixing of soap tray brass CP 150 x100mm size including cost of all charges etc., complete

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

(i) 90 mm dia

ii) 110mm dia

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

JPS CONSTRUCTION