GE 861 EWS-68(T)/2025-26

Demolition cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level with and including removing rubbish material from building and thrown in low lying empty area as compete all as specified and as directed by Engineer-in-charge.

Dismantling of timber of any description complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters of PVC door , wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters of PVC door ,wooden door shutter, wooden window shutter , Mild steel window and Mild steel ventilators (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 Sqm each complete all as specified and as directed by Engineer-in- charge.

Taking down cement or cement lime plaster from brick wall or concrete surfaces etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

Dismantling wall and ceiling boards (fiber, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed by Engineer-in-Charge.

Dismantling of plain or corrugated steel sheet any gauge thickness for roof covering complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work / stone masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 50mm thick Plain Cement Concrete 1:3:6, type C-2 (using 40mm graded stone aggregate), finished even and smooth without using extra cement as in plinth protraction complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75mm thick Plain Cement Concrete 1:3:6, type C-2 (using 40mm graded stone aggregate), finished even and smooth without using extra cement as in plinth protraction complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty area as directed by Engineer-in-Charge compete all as specified and as directed by Engineer-in-charge.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work using burnt clay sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in Cement Mortar 1:6 complete all as specified and as directed by Engineer-in- charge.

All as per serial item no. 13.00 here-in- before but but except bricks Note: Bricks shall be obtained from serial item no.8.00 here-in - before for use in this item.The bricks shall be used in this item after proper cleaning . The rate of cleaning of bricks is included in this item nothing shall be paid extra on this account.

Material & Labour for Machine cut kota slab 20mm - 25 mm thick ( Kota stone as approved by Engineer-in-charge) as in flooring , laid and jointed with grey cement slurry @ 3.00 Kg per Sqm mixed with pigment to match the shade of the slab including rubbing and polishing , laid over with and including 15 mm thick screed bed in Cement Mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Machine cut kota slab 20mm - 25 mm thick in one piece ( Kota stone as approved by Engineer-in-charge) as in vertical surfaces such as skirting, dado , pillar, risers of steps , etc. laid and jointed with grey cement slurry @ 3.00 Kg per Sqm mixed with pigment to match the shade of the slab including rubbing and polishing , laid over with and including 10 mm thick rendering in Cement Mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour for Rendering 10mm thick in Cement Mortar 1:6 , on fair faces of brick work or concrete surfaces , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and as directed by Engineer-in-charge.

Supply & Fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Non skid ceramic coloured tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc., set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Glazed Coloured Ceramic tiles ( colour as approved by Engineer-in-charge ) , size 450mm x 350mm x 7mm thick, as in vertical surfaces , set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Non skid ceramic coloured tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floor etc., set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Non skid ceramic coloured tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in vertical surfaces such as such as skirting, dado etc. , set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 605mm x 605mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centrecomplete all as specified and directed by Engineer-in-Charge. Note: The rate of 8mm thick Non asbestos fiber cement building board is not inclueded in this item .The measurement and payment of 8mm thick Non asbestos fiber cement building board shall be considered under serial item No.26 .00 here-in- after. Nothing shall be extra paid in this item.

Supply & Fixing Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing false celling 8mm thick Non asbestos fiber cement building board fixed in celling flat or sloping inserted in Gl frame complete all as specified and directed by Engineer-in-Charge.. Note: The measurement and payment of GI Frame shall be considered under serial item No. 25 .00 of BoQ here-in- before. Nothing shall be extra paid in this item.

Supply & Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by Engineer-in-Charge.

Material & Labour 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

Material & Labour 6mm thick plywood, grade BWR, Type BB, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

Material & Labour 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exceeding 03 Sqcm but not exceeding 6 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing second class soft wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Factory made 35mm thick framed, panelled shutter (two panel) with lock rail made of 2nd class Hard wood and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge. Note: Butt Hinges, Tower bolts, Handles , sliding door bolts and painting shall be measured and paid seperately under appropriate items of schedule 'A' BoQ.

Supply & Fixing 30mm thick second class hard wood Glazed and skeleton for window shutters, open rebated and prepared to received glass, gauze etc (without sash bars), edges of framing plain, chamfered, or rounded, fittered with cut mitred beads for securing glass etc complete all as specified and directed by Engineer-in-Charge. Note:- (i)Wire gauze / glass shall be measured and paid separately under appropriate items of Schedule 'A' BoQ. (ii) Butt Hinges, Tower bolts, Handles , sliding door bolts , ordinary rat tail pattern springs and painting shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. (iii) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. (iv)Primer shall be measured paid separately under appropriate item of BOQ.

Supply and Fixing 35mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), using 2nd class hard wood (as approved by Engineer-in-charge) edges of frming plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR Part-I, Section8, Clause 8.24 (a), supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-Charge. Note:- (i)Wire gauze / glass shall be measured and paid separately under appropriate items of Schedule 'A' BoQ. (ii) Butt Hinges, Tower bolts, Handles , sliding door bolts , ordinary rat tail pattern springs and painting shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. (iii) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. (iv)Primer shall be measured paid separately under appropriate item of BOQ.

Supply & Fixing 150mm long mild steel barrel tower bolts, stove enameled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 100mm long mild steel barrel tower bolts, stove enameled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 150mm long, mild steel pressed handles, oval type, stove enameled black, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 75mm long, mild steel pressed handles, oval type, stove enameled black, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 250mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each pane complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Powder Coated Anodised aluminium frame (minimum thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. Note: 1. During the weighing of aluminium section the weight of powder coating 50 micron shall not be considered. The payment shall be made only on the actual weight of aluminium section. 2. The rate of 50 micron powder coating is included in this item hence contractor shall quote his rate accordingly.Nothing shall be paid extra on this account.3. if the aluminium section provided at site with thickness of powder coating more than 50 micron by contractor nothing shall be paid extra.

Supply & Fixing Door shutter made of aluminium sections weighing 0.55 kg/Rm , Powder coated (coating not less than 50 micron ), of any colour (as approved by Engineer-in-charge) , with and including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws etc . complete all as specified and directed by Engineer-in-Charge. Note : 1. The rate of Glass is not included in this item and shall be measured and paid under appropriate items of Schedule of BoQ 3. The rate of cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, etc. is included in this item and nothing shall be paid extra on this account. 4. The rate of anodised aluminium fittings such as , hinges , handles , tower bolts, stopers, sliding bolt is not included in this item . The measurment and payment of these items shall be made under appropriate items of Schedule'A' BoQ.

Supply & Fixing Three track Slider window made of aluminium sections weighing 0.55 kg/Rm , Powder coated (coating not less than 50 micron ), of any colour (as approved by Engineer-in-charge) , with and including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays -150mm long (1 no.), hinges type B-21 -100mm long (2 nos.) ,suitable handle (1 no.) complete all as specified and directed by Engineer-in-Charge. Note : 1. The rate of glass for glazing and wire mesh cloth is not included in this item and shall be measured and paid under appropriate items of Schedule of BoQ 2. The rate of cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) is included in this item .Contractor shall quote his rates accordingly . Nothing shall be paid extra on this account. 3 Net opening will be measured for payment purpose for three slider shutters. 4. No measurment shall be considered sepertely for each shutter.

Material & Labour for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 5.5mm thick sheet tinted glass ordinary quality and glazing with aluminium beading/clips etc in square exc 0.5 sqm each pane complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 150mm long aluminium anodised tower bolt of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 150mm long aluminium anodised handle and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing to 100mm long steel butt hinges and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing aluminium alloy anodised sliding door bolt 250mm of length with hasp, staple (bolt type) and fixing clips of sheets cast or extruded section and fixing bolt and sliding bolts complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement vitreous china wash down water closet pan (pedestal pattern), white, with and including 'P' or 'S' trap, with and including seat cover and fixing with bolts, making good to floor in PCC M-15 (1:2:4) type B-1 (using 20mm graded stone aggregated), complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement Low level PVC flushing cistern 10 Ltr capacity symphonic action type, white with inlet ball valve float and handle including bracket complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement Vitreous China bowl urinal flat back, size of 465mm x 355mm x 265 mm white (minimum), with grating and union for discharge pipe with and including 32mm bore PVC waste pipe complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement Chromium Plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and bracket complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement stainless steel floor gratings , 125mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 15mm bore PVC connection with PTMT nuts of 600mm long complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement Rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position ,with and including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement Rotational moulded polyethylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position , with and including 20mm brass ball valve high pressure with brass rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparation of newly plastered surface of wall any description and applying two coats of oil emulsion distemper over chalk whitening on plastered surfaces complete all as specified and directed by Engineer-in-Charge.

Material & Labour Preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of alkali resistant primer complete all as spd & directed

Material & Labour for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

Material & Labour for Preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint over one coat of pink primer complete all as specified.

Material & Labour for Preparation of old painted GI/steel surfaces of any description not otherwise described over 10cm width or girth as in roof and applying one coat of synthetic enamel paint specified and directed.

Supply & Fixing in replacement 15mm bore Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe for brass ferrule complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 15mm stop valves/ Angle valve cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 15mm bore pillar tap cast copper alloy with capstan head, chromium plated, screw down high pressure, with or without lettered hot or cold with long screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing PVC connections 15mm size with PTMT nuts of length 375mm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement vitreous china wash basins size 450mm x 300 mm oval type with waste chain, porcelain stopper and plug , with and including brackets complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 15mm bore and connection complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 20mm bore and connection complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 15mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 20mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only 15mm bore GI tubing medium grade after throughly cleaning of pipe retrived from serial item no.76.00 here-in- before with all new fittings fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. Note: The rate of cleaning of old servicable pipe is included in this item and nothing shall be paid extra on this account.

Fixing only 20mm bore GI tubing medium grade after throughly cleaning of pipe retrived from serial item no.77.00 here-in- before with all new fittings fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge. Note: The rate of cleaning of old servicable pipe is included in this item and nothing shall be paid extra on this account.

Material & Labour 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 19/20mm dia MS Pipe powder coated Drapery rods of approved colour as in decorative type complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement brackets for drapary rod of powder approved decorative type suitable for fixing drapery rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 75mm PVC(SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 110mm PVC(SWR) bend any radius (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing PVC floor trap of size 75mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 Type B-1, using 20mm stone aggregates complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 75mm PVC(SWR) junction single(single T) equal or unequal (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 110mm PVC(SWR) junction single(single T) equal or unequal (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 110mm PVC (SWR) 'P' trap (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement 75mm PVC(SWR) vent cowl (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement chromium plated stainless steel soap tray of approx size 150 mm dia complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 18/19mm thick Pre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps (when open) in 30mm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 150mm hasp and staple, mild steel, wire type stove enameled black, including bolt to hinge plate and fixed with screw complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 40 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggregates as in floor , finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Plain cement concrete 1:3:6 , Type - C1 using 20 mm graded stone aggregate as in lintels up to 1.5 mtr span, cills and other similar bands, plinth courses, parapets, copings, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including use and waste of form work complete all as specified and directed by Engineer-in-Charge.

Hacking out old or broken glass (any thickness size quility or description) from steel frames or stone concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

Material & Labour for one coats of cement based paint on walls with and including washing, rubbing down and stopping of old painted surfaces complete all as specified and directed by Engineer-in-Charge.

Material & Labour complete removal of existing treatment and with and including applying 3mm thick layer of Birla wall care putty and with and including applying two coat of Oil emulsion distemper white or tinned over with and including one coat of primer on walls, etc complete all as specified and directed by Engineer-in-Charge.

Refixing of shutters of any description in same opening exceeding 1.00 Sqm and not exceeding 2 .00 Sqm complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 25mm bore Chromium Plated stainless steel Curtain Rod with stainless steel brackets, complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement water closet vitreous china squatting pan, Orissa pattern size 580mm x 440mm white with integral foot rests with and including provision of lime concrete bedding with and including `P' trap and connection to drain and to flushing pipe anti symphonage pipe complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Box type steel ventilator with top hung shutters including hinges, steel handle, steel peg stay complete with glazing bar dovetailed/welded complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 20mm dia stainless steel tubular towel rail with stainless steel brackets, complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cables, pipes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material of any kind not exceeding 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in any kind of soil complete all as specified and directed by Engineer-in-Charge.

Supply & fixing for Mild steel Framed work as in grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-charge.

Taking down carefully aluminum / copper point wiring on Teak Wood Batten / in conduit / with conduit (light /Fan / socket or power) complete with and including taking down fittings such as switches, ceiling roses, pendants, Regulators, sockets, light fittings etc complete all as specified and directed by Engineer-in-Charge. Notes: (i) The weight of aluminium scrap, copper scrap and scrap iron for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill. (ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface shall be measured and paid seperately under serial item nos.114.00 to 117.00 & 148.00 to 150.00 of BoQ.

Material and labour for concealed Point wiring for Modular fittings using approved colour coding as per IS (Red, Black and Green for single phase circuits), in new PVC conduit complete with and including 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , drawn through with and including new PVC rigid conduit 20mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, powder quoted sunken box of required size for light / fan point controlled by one way modular switch 5Amp / 6Amp, with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. with and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge . Notes for serial item nos.114.00 to 117.00 : (i) Modular frame , Modular switches one way 5 /6 Amp , Modular switches one way 15 /16 Amp, Modular socket out lets 5 /6 Amp & Modular socket out lets 15 1/6 Amp shall be measured and paid seperately under respective items of Schedule'A' BoQ. (ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account. (iii) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips as directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account. (ii) The rate of sunken box of required size is included in this item and nothing shall be paid extra on this account.

All as per srl item No.114.00 here in before but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per srl item No.114 here inbefore but for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 114.00 of BoQ here-in-before but 2.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 2.50 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc for 3 pin socket outlet 15 Amps with complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Cutting chases, pinning in making good to facing where required and pointing in cement motor 1: 3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed conduct wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and directed by Engineer-in-Charge. Note: Cutting chases for serial item no.114 to 117 of BoQ & 148.00 to 150.00 of BoQ and is included under serial item no.114 to 117 of BoQ & 148.00 to 150.00 of BoQ and shall not be measured and paid under this item.

Supply & Fixing ceiling rose (ISI Marked ) surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Modular switch 1 way 6A,1 module (ISI Marked ) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in Modular switch 1 way 16A,1 module (ISI Marked ) all complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in Modular socket, 6A - 2/3 pin combined 2 modules (ISI Marked ) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in Modular socket 6/16A,2/3 pin, combined 2 module (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing White cover plate with frame, 2 module complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing White cover plate with frame, 3 module complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing White cover plate with frame, 4 module complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing White cover plate with frame, 6 module complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing White cover plate with frame, 8 module complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing lamp holder PVC/polycarbonate insulated body type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of LED 7 watt pin type bulb complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp complete all as per manufacturer's instructions suitable for roof ceiling with and including connecting up with driver from ceiling rose with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account.

Supply and fixing in replacement new generation wall/surface mounted 20W LED batten fitting, 4 feet surface mounted provides high quality economic energy saving lighting complete all as per manufacturer's instructions with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge. (a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account.

Supply and fixing in replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 08 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply and fixing in replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 12 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply & Fixing MCB SP 6-32 Amps,10KA, 'B' series 240V complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing MCB SPN 32 Amps,10KA 'C' series 240V complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement security light brackets made with 40mm dia light grade galvanised iron pipe 1.50mtrs long with 30° bend with and including flat iron clamps , nuts, bolts and washers to brace the same properly duly painted with two coats of silver coloured synthetic enamel paint over one coat of red oxide zinc chrome primer and complete all as specified and directed by Engineer-in-Charge.

Taking down old unsrviceable service cable/UG cable of cross-sectional area 16 Sq mm 2 core including old uservicable bricks/ PCC concrete cable cover all as specified and directed by Engr-in- Charge.

Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor having cross sectional area 16 Sqmm 2 core conforming to IS-7098 (Part-I -1988) complete all as specified and as directed by Engineer-in-Charge. (Excavation and earth work, sand cushioning & GI pipe shall be measured and paid for separately)

Supply & Fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type, energy saving and environment friendly light fitting with electronic gear housed with high pressure die cast aluminum housing LED street light luminaires complete with IP66 protection including all accessories and taking down old existing unsv, complete all as specified and directed by Engineer-in-Charge.(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account.

Supply & Fixing Exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete all as specified & directed by Engr-in- Charge.

Material and Labour in replacement Sub main wiring with two single core of size 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked including cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-I ISI marked including all fitting such as Tee, Elbow, bend etc drawn in and including one single core of size 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:- (a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b) Three single core 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and including non metallic rigid PVC conduit of size 25 mm ISI Marked dia shall be measured as one length.

Material and Labour in replacement Sub main wiring with two single core of size 10.00 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked including cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-I ISI marked including all fitting such as Tee, Elbow, bend etc drawn in and including one single core of size10.00 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:- (a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b) Three single core 10.00 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and including non metallic rigid PVC conduit of size 25 mm ISI Marked dia shall be measured as one length.

Material and Labour for in replacement earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia medium grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed. (ii) The rate of earth work in soft/loose soil i.e. excavation, returing filling and removal, form work is included in this item and nothing shall be paid extra on this account. (iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply, fixing & commissioning sheet metal enclosure (junction box) of suitable size fabricated with CRCA sheet steel 2mm thick, front door openable type, powder coated included earth bars cement spill protector cable ties, blanking plates suitable for housed 4 pole MCCB 63Amp as incommer, copperbus bar 200 Amp rating outgoing MCB 40Amp SPN, multifunctioning meter, indication lamp etc complete and suitable to accommodate the following accessories:- (a) MCCB 63Amps 4pole,16 KA,Thermal magnetic - 1 Nos. (b) Changeover switch 63Amp 4 pole- 01 No. (c) MCB, SPN 40Amps,10KA- 3 Nos (Out going). (d) MCB, SP 6 Amp,10KA,Thermal magnetic- 2 Nos (Out going). (e) Multifunction meter - 01 No. (f) Indication lamps (R,Y,B) LED type - 1 set. (g) Copper bus bar 200 Amp rating with colour coded heat shrinkable sleeve TPN- 01 set. Note: (i) sheet metal enclosure( junction box ) shall be flush mounted in staircase wall at adequate height as directed by Engineer-in-charge . (ii) Making good the surfaces with existing surface with cement, paint etc . . The rate of this aspect is included in this item and nothing shall be paid extra on this account.

Supply & Fixing Changeover switch off load type 415 volts TPN, 4 pole, 100 Amps built in sheet metal enclosure complete all as specified and directed by Engineer-in-Charge. Note : The rate of sheet metal enclosuer is included in this item and nothing shall be paid extra on this account.

Material and labour for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , with and including PVC casing and capping of medium grade of suitable size and run on wall / surface with all fittings (ISI Marked) with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. controlled by one switch for one light point/ fan point with and including CI/MS/ wooden sunk box of required size with and including 3mm thick plastic laminated sheet cover & as directed by Engineer- in- Charge including cutting, chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge. Notes for serial item nos.148.00 to 150.00 : (i) switches one way 5 /6 Amp , switches one way 15 /16 Amp, socket out lets 5 /6 Amp & socket out lets 15 1/6 Amp shall be measured and paid seperately under respective items of Schedule'A' BoQ. (ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account.

All as per srl item No.148.00 here- in- before but for One 3 pin socket outlet, 5 Amps, independent board complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 148.00 of BoQ here-in-before but 4 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 4 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc for 3 pin socket outlet 15 Amps with complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing switch piano flush type, 05 / 06 Amps single pole, one way 240 volts (ISI Marked )complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 volt (ISI Marked ) complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal 240 volt (ISI Marked )complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Fan step regulator, 120W - 2 module type electronic fan regulator, duly(ISI Marked ) with and including connector complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 4 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply and fixing in replacement gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Cutting of existing CI / GI pipe line of 20mm to 50mm bore and inserting with and including tee and taping new connection with all accessories complete all as specified and as directed by Engineer-in-charge.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ

Please Enable Macros to View BoQ information