REPAIR/MAINT OF INTERNAL ELECTRIFICATION INCLUDING FANS AND GEYSERS AT VARIOUS OFFICERS MD ACCN GUEST HOUSES SINGLE OFFICERS ACCN AT ZONE A AT NDA KHADAKWASLA

Amount

Repair / maintenance of internal light fitting of any type like tube lights / wall bracket light fittings / ceiling lights / bulk head light / mirror lights etc in its position, testing all the compenents / parts, wiring etc, identifying and replacing the defective components like choke (ballast), tube rod, side holders, holders, lamps etc complete all as directed by Engineer-in-charge. Note: (i) The rate against the above mentioned item is deemed for cost of labour only. (ii) Cost of spares like Choke (ballast), capacitor, lamp holder, connector, connection wire etc) replaced against above mentioned item will be measured & paid for separately under respective items of Sch 'A' here-in-below. (iii) The contractor's representative will report to concerned JE E/M at 0900hrs daily to collect the list of defects and will submit the completion report on following day before 0900hrs to the JE E/M. (iv) The contractor shall rectify the defects and make the light fittings functional within 24 hours from the time the list of defective lights is handed over to him / his rep by the concerned JE E/M. In case the light fitting is not made functional for whatsoever reason within the specified time limit, an amount of Rs 100/- per such defective light fitting per day will be recovered from the amount due to him through RAR / Final Bill.The contractor shall engage separate team of technicians / repairer for each at D1& D2, E3, D3 & Bombay stadium area. (v) The contractor shall maintain proper record of repair / maint in a binded compliant register and complaint slip books duly signed by the user and bringing out the details of spares replaced and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (vi) The contractor shall maintain sufficient stock of spares / material required for repair / maint of light fittings with the concerned JE E/M against the supply only items here-in-below.

Supply only following spares for light fittings of branded make as mentioned in the list of make enclosed with Particular specifications for replacement :- Starter suitable for 36/40 watt Tube light fitting

Ditto all as per item No. 2 above but Spring loaded G13 side holders (set of 2) suitable for 36/40W FTL fitting

Ditto all as per item No. 2 above but Electronic ballast slim type suitable for 36/40W FTL fitting. Make: Havells/Philips

Ditto all as per item No. 2 above but PVC / polycarbonate lamp holders batten/ Angle type

S&F in replacement modular step type fan regulator 120W, 2 module Make- Vinay/Anchor Roma

S&F in replacement modular switch piano type 6 amps one way one module Make - Vinay/ Anchor/Roma

S&F in replacement modular switch piano type 16 amps one way one module Make - Vinay/ Anchor/Roma

S&F in replacement modular Socket, 6A - 2/3 pin 2 module Make - Vinay/Anchor Roma

S&F in replacement modular Socket, 6/16A - 2/3 pin 2 module Make - Vinay/Anchor Roma

S&F in replacement for ceiling rose, 2 to 3 terminals /PVC/Polycarbonate, isolated body.

M & L in replacment of fan regulator electronic step type suitable for 1200/1400 mm sweep fan as per the sample provided by the Engineer-in-charge.(Make:Anchor/Vinay)

M & L in replacement of door bell AC 230 volts single phase ding dong type all as specified and directed. Make:Anchor/Vinay

M & L in replacement bell push, flush type 5 Amps all as specified and directed. (Make:- Anchor / Vinay)

S & F in replacement of switch piano flush type 5 Amps SP one way complete all as specified. (Make:- Anchor/Vinay)

S & F in replacement of switch piano type 15 Amps SP one way complete all as specified. (Make:-Anchor/Vinay)

S & F in replacement of switch socket combination 5/6 Amps flush mounted 5 pin multi purpose complete all as specified. (Make:Anchor/Vinay)

S & F in replacement of switch socket combination 5/15 Amps flush mounted 3/5 pin multi purpose complete all as specified.(Make:Anchor/Vinay)

S & F in replacement of socket 5/6 Amps flush mounted 3 pin complete all as specified. (Make:Anchor /Vinay)

S & F in replacement of socket 5/15 Amps flush mounted 3/5 pin multi purpose complete all as specified. (Make:Anchor/Vinay

S & F PVC unbreakable surface boxes suitable for 5Amp switch socket combined. Make - Press Fit

S & F PVC unbreakable surface boxes of size suitable for 15Amp switch socket combined. Make - Press Fit

S &F in replacement for white cover plate with frame 1 module. Make:As per the sample given

S & F in replacement for white cover plate with frame 3 module. Make:As per the sample given

S & F in replacement for white cover plate with frame 4 module. Make:As per the sample given

S & F in replacement for white cover plate with frame 6 module. Make:As per the sample given

S & F in replacement for white cover plate with frame 8 module. Make:As per the sample given

S & F in replacement PVC unbreakable surface boxes suitable for modular switches 1 module.

S & F in replacement PVC unbreakable surface boxes suitable for modular switches 3 module.

S & F in replacement PVC unbreakable surface boxes suitable for modular switches 4 module.

S & F in replacement PVC unbreakable surface boxes suitable for modular switches 6 module.

S & F in replacement PVC unbreakable surface boxes suitable for modular switches 8 module.

S & F in replacement of 1 module Blanking plates complete all as specifed and directed by Engr-In-Charge. Make:As per the sample given

Taking down carefully copper/aluminium point wiring (light/fan/socket) including all accessories wire, casing caping/conduit, screws etc and making good the disturbed surfaces complete all as directed

M&L for point wiring with 1.5 sq mm copper conductor FR (multistrand) PVC insulated ISI marked unsheathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FR cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for modular type switches, sockets, fan regulator etc for following :- One light/Fan point controlled by one way switch 6 Amps 240 volts

Ditto all as per item No 35 above but one 3 pin 6 Amps socket out let point on independent board.

Ditto all as per item No 35 above but One 3 pin 6 Amps socket out let point on same board.

Ditto all as per item No 35 above but one bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq mm size.

M&L for point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket and switch outlet power point independent circuit

M & L for secruing loose wiring and repair to point wiring with necessary rigid non metalic PVC casing caping double lock type ISI marked of size not less than 19mm inclusive all accessories complete as specified and directed.

S & F flexible conduit pipes of dia not less than 19 mm complete all as specified and directed. Make: As per sample approved by Engineer-in-charge

M & L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2.5 Sqmm , 1100 Volts grade in and including casing caping medium grade not less than 19 mm complete with conduit accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and directed (Two runs of 2.5 Sqmm cable with 01 run of 2.5 Sqmm earth wire along with casing caping shall be measured as one RM)

M & L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including casing caping medium grade not less than 19mm complete with conduit accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed (Two runs of 04Sqmm cable with 01 run of 4 Sqmm earth wire along with casing caping shall be measured as one RM)

M & L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including casing caping medium grade not less than 19mm complete with accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed (Two runs of 06 Sqmm cable with 01 run of 6 Sqmm earth wire along with casing caping shall be measured as one RM)

Taking down carefully sub main wiring of any type and size and making good disturbed surfaces complete as directed.

Supplying and fixing 1100 volts grade heavy duty cable 4 Sqmm PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular

S & F factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB ) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified Make/Model of VTPN DB : Legrand/L&T/ Siemens Note:MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F in replacement MCB DB 12 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engr-in-Charge. Make: Havells/Legrand. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement MCB DB 08 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engineer-in-Charge. Make: Havells/Legrand. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement MCB DB 04 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engr-in-Charge. Make: Havells/Legrand.Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement MCB DB 02 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as directed by the Engineer-in-Charge. Make: Havells/Legrand. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F MCCB with rating of 100 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals.

S&F MCCB with rating of 63 Amps, 415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu). MCCB should be with suitable spreaders and phase barriers for each terminals.

S & F in replacement of C Curve MCB SP 6-32 Amps working on 240 volts,50 Hz 10 KA complete all as specified and directed.

S & F in replacement of C Curve MCB DP 6-32 Amps working on 240 volts,50 Hz 10 KA complete all as specified and directed.

S & F in replacement of C Curve MCB SPN 40-63 Amps working on 240 volts, 50 HZ,10 KA complete all as specified and directed.

S&F MCB TPN 63 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing.

S & F 18/20watt,230V surface and wall mounted LED Tube Set, including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified . Make:Luker or equivalent in Wipro/Havells

Supply only LED tube light (single side connection) with diffused optics ultra bright LED tube light 18/20watt with high efficiency suited for installation in existing T8 tube light with G13 lamp holders all as specified and directed by Engineer-in-charge. Make:Philips or equivalent in Wipro/Luker/ Havells

S&F in replacement 1x18/20W,230V surface and wall mounted batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified. Make:Luker /equivalent in Wipro/Philips

S & F in decorative wall mounting gold finish fixture with plastic body suitable for 10W LED(B-22 base) including 01x10 W LED bulb and connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified. Make:Havells or Philips/Wipro

S&F in replacement 1x10 watt,230V surface mounted LED downlight with white powder coated polycarbonate housing and pressure die-cast heat sink having high efficiency, including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified . Make - Havells Cat part No INTEGRANEOSURFACELS10WLED840S or equivalent in Philips/Wipro

S&F in replacement 1x10 watt,230V surface and wall mounted LED batten suitable for mirror light with polycarbonate housing and integrated electronic electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified . Make - Luker/Philips/Wipro

Taking down ceiling fan/exhaust fan of any sweep for servicing / repairing / maintenance, opening up, identifying and replacing the defective parts, cleaning, greasing,etc, reassembling and hanging up/fixing back at its original position, connecting up and testing complete all as directed. Note : 1.Cost of spares such as capacitors, bearings etc will be measured and paid for separately under respective Item of sch A as supply only. Note No (iii) to (vi) below Item No 1 of this schedule are equally applicable to this item too.

Supply only capacitor of 2.5 mfd for ceiling fan/exhaust fan. Make:Tibcon/Epcos

Supply only capacitor of 4 mfd for air circulator/exhaust fan. Make:Tibcon/Epcos

Supply only bearing No.6201/6202/6203 or any other No matching to the existing size and suitable for ceiling fan/exhaust fan/wall mounted fan. Make:SKF

S & F in replacment aluminum fan blades sutable for heavy duty exhaust fan of any sweep as per the sample given by the Engineer-in-charge

S&F ceiling fan of sweep 1200mm, 240volts, of not less than 3 star BEE rating milk white coloured connecting up with twin core 1.0 Sqmm cable from ceiling rose including required length of hanging rod including complete all as specified. Make:Orient/Havells/Crompton Greaves. (Note:Old ceiling fan should be deposited in MES Store Yard)

Disconnecting electric connection and taking down carefully fan of any type and size/sweep as described below, removing the burnt winding of fan motor rewinding with super enarneled copper winding wire of suitable gauge or of matching size to the exisiting wires including all insulating material such as insulation paper sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and reflxing to original position complete all as directed by Engineer-in-charge for following :- Celling fan of size 1200 sweep.

Ditto all as per item No 70 above but exhaust fan of 300 mm sweep.

Ditto all as per item No 70 above but wall mounted fan of 400 mm sweep.

M&L for painting the ceiling fan of any sweep with two coats of synthentic enamel paint by rubbing/removing the old paint carefully without any damage to the fan or fan blades all as specified.

Ditto all as per item No 73 above but exhaust fan of size 12" (300 mm) sweep

Dismantling and removing rusted louvers (set of 4) suitable for 300 mm sweep exhaust fan supply and fix MS louvers duly painted gray coloured suitable for 300mm heavy duty exhaust fan alongwith four number mounting bracket with bolts, nuts washers etc complete all as directed.

Disconnecting and taking down existing userviceable geyser of 25 ltrs capacity of any make/brand, taking it to civil workshop for repairing. Opening the geyser and dismanting all parts and taking out inner tank/container, removing dents making to shape including welding / brazing the leakage portion, filling the portion between inner tank and out casing of geyser with new glass wool heat insulating material . Reassembling and painting the outer casing of geyser with two coats of superior quality synthetic enameled paint and re- fixing to original place complete all as directed

M&L in replacement thermostat 0-85⁰C suitable for geyser of 25 ltrs capacity.

M&L in replacement heating element of capacity 1.5 KW of any type and shape suitable for existing 25 ltrs capacity geysers of any brand / make

M&L in replacement flow unit (inner pipe assembly) suitable for geyser of 25 ltrs capacity of any brand/make and for vertical/Horizontal type including rubber ring/gasket.

S & F in replacement metallic flexible hot water connection 600 mm long including necessary washers suitable for geysers of 25 ltr capacity complete all as specified and directed.

S & F in replacement sheet metal enclosures Single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB single pole 10 Amps, 240 volts complete with all accessaries etc complete all as directed by Engineer-in-charge.

S & F fix in replacement metal clad plug top 3 pin,10 Amps, 230 volts, ISI marked heavy duty for geyser connection cord.

S & F neon lamp indicator square/round type after taking out old incl taking down old one.

S & F in replacement PVC insulated round cable 3 core stranded copper conductor 2.5 sqmm as in connection cord of the geyser, Make : Polycab / Havells /Primecab

S & F in replacement plug top 3 pin, 15/16 amps, 230 volts, ISI marked heavy duty for geyser connection cord.

S & F in replacement plug top 3 pin, 5/6 amps, 230 volts, ISI marked.

S & F in replacement NRV valve of size 15mm dia of Brass complete all as specified and directed.

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for solar water heater system of existing manufacturer brand / make.

Fixing only the 25 geyser and connecting up including with suitable fastner as per ground requirement complete all as specified and directed. Note:Geyser will be issued under Sch 'B' store free for fixing only

M&L for earthing complete with galvanised steel earth plate electrode 600x600x 6.3 mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc complete all as specified and directed by Engineer-in-Charge.

S&F AC single phase static energy meter of accuracy class 1.0,rating 5-30A, 240V,50Hz only KWH compact meter with pifler meter box with sealing screw provision(LCD mini). Make:HPL/L&T

S&F in replacement 3mm thick white coloured hylam sheet (bakelite) for mounting switches complete all as directed.

S&F in replacement LED building security light fiitting 25 W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting soource and lens embeded PC cover having TOP opening seperate driver compartment complete fixing with GI bracket made out of 40mm bore GI pipe light grade 1.2 Mtr long bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed by Engineer-in-charge. Make:Havells/Philps/Luker

M & L for electronic driver suitable for 25 watts LED building security light fittings. Make: Crompton/Wipro

Supply only honor board LED (warm white) fitting of 1x10W individual LED lenses, chorme coloured. Make Havells/Philips

Supply only LED bulb 1 watt of any color sample given by the site-in-charge with B-22 base all as specified. Make:Syska/Philips

S&F in repalcement of bed lamp fitting suitable for 5watt LED bulb(B-22) base including connecting up with twin core twisted flexible copper condctor cable complete all as specifed.

Supply only LED high glow bulb 12watt,WW of base B22 conforming IEC 60901 & IEC 61199 with lumen output 6500K complete all as specified. Make:havells/Philips/Luker

S&F high speed wall mounted fan of sweep 400 mm,Full copper motor, auto thermal overload protection,compact style and powder coated gurads & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories complete all as specified and directed. Make:Crompton or equivalent in Havells/ Orient

S & F Plastic ventilation fan of 225mm sweep inclduing replacing the plywood as per the site requirement. Note: Old Exhuast fan should be deposited in MES store yard.

S & F Metal body ventilation fan of 225mm sweep inclduing replacing the plywood as per the site requirement. (Note: Old Exhuast fan should be deposited in MES store yard)

S&F 40 W suspended LED Light with high efficiency providing soft-light and glare free symmetrical illumination including suspension kit including connecting up with twin core twisted flexible copper cable from ceiling rose to fitting complete all as specified and directed. Make: Havells Cat part No. CONSTA1144P40WLEDSPMMAWH or equivalent in Luker/Philips

S&F 10 watt surface mounted LED Bulk Head Luminaire with ABS Body & Polycarbonate diffuser, IP54 including all connection complete all as specified and directed by Engineer-in-charge.

M & L for electronic driver for 20 watts COB lights Make should be as per the existing manufacturer

M&L in repalcement recess type LED ceiling lights 18/20 watt LED with ceiling cut out of Ø 160 mm Environmental friendly, energy saving, recess mounted downlighter with separate replaceable electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully complete all as specified and directed. Make: Luker/Havells/Jaquar

S&F Retro fit 4 pin 20 watt LED PLL with direct plug and play. Make Jaquar Cat No LDZL01X20XC or Bajaj/Wipro

S&F electrical meter box compartmentalized design suitable for one energy meter and one 12 way DB, outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakelite sheet for mounting the energy meter and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box should be as per site requirement complete with all accessories prewired twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S&F electrical meter box compartmentalized design suitable for 4 x energy meter and 4 x Eight way SPN DB, outdoor wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakelite sheet for mounting the energy meters and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box should be as per site requirement complete with all accessories prewired twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

Sparkh Electricals & Works

Aim Enterprises

KESARI AND SONS

Tejas Enterprises