INSTALLATION AND ENERGISATION OF DIHASARICHUAN-IX TW LI PROJECT

Earth work in hard soil 50m initial lead & 1.5 m initial lift including rough dressing & breaking of clods to minimum 5 cm to 7 cm and laying in layers not exceeding 0.30M (1’-0”) in depth including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Earth work in excavation of foundation in hard soil within 50 m initial lead & 1.5 M initial lift including dressing & levelling the bed & depositing excavated materials within above lead & lift including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Filling in F&P with excavated materials including well watered and rammed including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Filling in F & P with sand well watered and rammedincluding cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Cement concrete (1:4:8) with 4cm (1½”) size hard granite metal C.B. metal of approved quality from approved quarry with required ramming,watering and curring etc. complete including cost, royalty & convence charges of all material to work site, supply of cement ,T&P required etc. complete except GST as per the direction of the Engineer-incharge.

C.C. (1:2:4) with 12mm (½”) size hard granite chips (crusher broken) of approved quality from approved quarry with ramming, watering and curring etc. complete with cost of all materials involved like supply of cement including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Reinforced Cement concrete (1:2:4) with 12mm (½”) size hard granite chips (Crusher broken) for RCC works including hoisting and laying with approved quality from approved quarry with ramming, watering and curring etc. complete with cost of all materials involved like supply of cement including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

2.5cm damp proof Course with Cement concrete (1:2:4) with 12mm (½”) size hard granite chips (hand broken )including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Supplying, straightening, cutting, bending, binding, fitting,placing and fixing uncoated HYSD bar reinforcement etc complete including supplying, straightening, cutting, bending, binding & tying the grills & placing in position including cost of binding wire 18 to 20 guage per Qntl. Including cost of HYSD Still Bar (FE 415/ FE 500) andincluding cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Rigid smooth centering shuttering for R.C.C. work including false work and dismantling then after casting including cost of all cost etc. complete (for 9.00 sqm.) for R.C.C.Lintles including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Fly ash Brick masonary in cm(1:6) in F&P 25cm X 12cm X 8cm size including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Fly ash Brick masonary in cm(1:6) in super structure including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

10cm dry brick khoa well watered & rammed to receive A.S.Flooringincluding cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

2.5 cm. thick A.S flooring with cement concrete (1:2:4) including punning using 12mm size C.B. chips including at cost etc. complete including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

12mm (½") thick C.P. (1:6) over brick works.including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Cement punning including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Labour charges for fitting of Iron Door (size 1.0x2.0m) including cost of door and fitting materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Labour charges for fitting of Iron Ventilator (size 0.45x0.30m) including cost of door and fitting materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

White washing 2 coats with shell lime per 1 Sqm. including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Colour washing 2 coats with shell lime over white washing 2 coats with shell lime to walls and ceiling per 1 Sqm. including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Priming one coat with any approved primer for iron work including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Painting two coats with approved paint on iron work including cost of all materials, T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per instruction of Engineer-in-Charge.

Labour charges for letter writting on display board in black colour on yellow back ground painting including cost of material, labour etc. including cost of materials, labour, T&P required, transportation to site from site stock yard, cess etc complete except GST as per direction of Engineer-in-Charge.

Cost of laying & fitting of ARV, BFV and Weldless G.I. Tees with distribution pipe line including labour, T&P required, transportation to site from site stock yard, cess etc complete except GST as per direction of Engineer-in-Charge.

Supply of 160mm dia HDPE PE 80- PN 4 ISI marked High Density Polyethylene (HDPE) Pipes for water supply as per IS-4984/2016 with proper grade and pressure rating including ex-factory rate, entire cost involved in Pre-delivery test & Post delivery test with correspoding test marking on the body of pipes along with name & address of manufacture , cost of transportation from factory to project site stock yard including loading & unloading, storage at site stock yard, watch and ward etc. and handing over to Pani Panchayat President or Secretary with due approval of authority including all taxes and cess etc. complete but excluding cost of GST. Pre-delivery test & Post deliver tests are to be conducted at the facility of CIPET, Bhubaneswar and test reports thus obtained from CIPET, Bhubaneswar are to be submitted to the Engineer-in-Charge.

Fitting of 160mm dia HDPE PE 80- PN 4 ISI marked High Density Polyethylene (HDPE) Pipes for water supply as per IS-4984/2016 with proper grade and pressure rating with supply of all required accessories materials , labour, T&P for jointing of 160mm dia High Density Polyethylene Pipes by butt fusion welding method as per specification & laying in trenches with desired leveling, testing including fitting and fixing up of required no. of attachments for Outlets and Shaddles and Riser Nipples, fitting air valve, equal Tee etc. complete including cost of transportation from stock yard to work site complete as per direction of the Engineer-in-Charge.

Earth work in hard soil such as hard stiff clay,stiff black cotton,hard red earth,shales,moorum ordinary gravels within 50m initial lead and 1.5m initial lift including rough dressing & breaking of clods and stacking rubble or spreading and levelling within the site as the case may be etc.complete including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per direction of the Engineer-in-charge.(Mechanical 60% & Manual 40%)

Filling in F & P with excavated materials, after laying and fitting of HDPE pipes with fitting items, including well watering and ramming in hard soil such as hard stiff clay,stiff black cotton,hard red earth, shales, moorum ordinary gravels within 50m initial lead and 1.5m initial lift including rough dressing & breaking of clods and stacking rubble or spreading and levelling within the site as the case may be etc.complete including cost of all T&P required for the work, cost of transportation, cess, royalty etc complete except GST as per direction of the Engineer-in-charge. (Mechanical 60% & Manual 40%)

Cost of construction of outlet, fitting of short piece of PVC pipe and soil errossion minimisation arrrangements including cost of labour, T&P required, transportation to site from site stock yard, cess etc complete except GST as per direction of Engineer-in-Charge.

Labour charges for fitting of Sluice valves & / NRVs along PVC pipeline & / lifting &/ lowering of pump sets including cost of labour, T&P required, transportation to site from site stock yard, cess etc complete except GST.

Electrical Earthing including including cost of materials, labour, T&P required, transportation to site from site stock yard, cess etc complete except GST as per direction of Engineer-in-Charge.

10 HP Submersible motor pump of 25 mtr head with 1300 LPM discharge of reputed brand with BEE Star rated energy efficiency suitable for 200 mm dia tube well as per IS specification with 2 pair U-Clamp & 30 mtr of 4.00 sqmm flat cable and Impeller: Bronze grade LTB-2 of IS 318/1981 as per IS specification including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

3x10 sqmm PVC insulated (HD) tropoder armoured Electric Cable with alluminum conductor for use in 3 phase power system of working voltage upto & including 1100 volts at 50Hz confirming to IS 7098(Pt-II) including cost of transportation to site including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

2.50mm2 Submerssible (3 Core) Flat Cable ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

Control Pannel with Automatic Star delta Starter, sheet steel enclosure suitable for operation of Squirrel cage induction motor up to 15 HP with 20 Amp (AC -3) duty contractor at 415 Volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & no volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The Starter should provide dependable protection against over load and single phasing fitted with Volt Meter, Ameter, MCB in complete shape including Indicator Lamp including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

63 AMP Triple Pole Mainswith confirming to IS No.4064(Part I & II) with ISI marking of reputed company with utilisation capacity cagegory AC- 22 including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

4KVAR Power Shunt Capacitor with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

4.0 mm2 PVC Single Core Copper Wire ISI mark of reputed Company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

6mm2 PVC Insulated Steel Wire Rope ISI mark of reputed Company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

T&P materials kit comprising of tester, screw driver, DE spanner, Plier, Ring spaner suitable for maintainence of LIP

100mm dia nominal bore G.I.pipe having wall thickness 4.5mm electrical resistance welded of medium class confirming to IS- 1239(part-1/2004) with latest ammendments, screwed at both ends as per IS-554 with socketed at one end and the other end protected with plastic threaded protector including its transportation and unloading at L.I.P. site. The socket confirming to ISI 1239(part II/1992) with latest ammendments in random length of 4 to 7 mtr.Each pipe should bear IS certification and manufacturers name/trade mark including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia G.I.Bend ( Medium Duty) conforming to IS No-1239 (part II/1992) with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia G.I.Flange ( Medium Duty) conforming to IS No-6392/1971 with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia G.I.Socket ( Medium Duty) with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia C.I.Double Flanged Non Return Valve swing type PN-1.0 (IS-5312(Part-I-2004) with bypass arrangement with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia C.I.Sluice Valve Flanged type PN-1.0 as per (IS-14846-2000 Standard) with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

150mm dia C.I. Butter Fly Valve BS:5155/15: 13095-CI MOC Lever Operated PN-1.0 with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

Nuts and Bolts including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

Thick Rubber Insertion 3mm thick including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

160mmx160mmx110mm dia Weldless G.I.Tee (3.6mm thickness and min. height of 1.2 mtr.) with bend, closing and opening arrangement of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

200X100mm dia M.S.T/W Cap with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

100mm dia M.S T/W Clamp (Pair) with ISI mark of reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

50mm dia C.I.Air Release Valve (single action) with saddle and Raiser pipe conforming to IS 14845 (SI) with ISI mark from reputed company including cost of material, transportation, cess etc. complete except GST as per instruction of Engineer-in-Charge.

160mmX110mm HDPE Reducer

Miscellaneous item like cleaning of site, overburden earth cutting etc

Cost of supplying of 160 mm HDPE Elbow spigot design 6 kgof ISI marked HDPE pipe fitting materials for High Density Polythelene (HDPE) Pipes for water supply of different nominal diameter as per ISI speifications including the rates of ex-factory, transportation, Cess etc complete but excluding cost of GST.

Cost of supplying of 160 MM HDPE Tail piece 160 mm longof ISI marked HDPE pipe fitting materials for High Density Polythelene (HDPE) Pipes for water supply of different nominal diameter as per ISI speifications including the rates of ex-factory, transportation, Cess etc complete but excluding cost of GST.

Cost of supplying of 160 MM HDPE End cap of ISI marked HDPE pipe fitting materials for High Density Polythelene (HDPE) Pipes for water supply of different nominal diameter as per ISI speifications including the rates of ex-factory, transportation, Cess etc complete but excluding cost of GST.

Cost of supplying of 160X160X160 mm HDPE Tee spigot design 6 kgof ISI marked HDPE pipe fitting materials for High Density Polythelene (HDPE) Pipes for water supply of different nominal diameter as per ISI speifications including the rates of ex-factory, transportation, Cess etc complete but excluding cost of GST.

Cost of supplying of 160 mm slipon flangeof ISI marked HDPE pipe fitting materials for High Density Polythelene (HDPE) Pipes for water supply of different nominal diameter as per ISI speifications including the rates of ex-factory, transportation, Cess etc complete but excluding cost of GST.

Construction of 3 phase 11 KV HT line as per REC standard confirming to IE Rules 1956 with 300 kg 9 M long PSC Pole with 55 Sqmm AAA Conductor average span 40mtr , 11 KV "V" Cross arm required No.of 11 KV T & C Disc. polymer Insulators in tension point & 11 KV Pin Polymer insulators, Couping & Padding of Poles with all G.I.Channels. Danger Board at each Pole, Anti Climbing Devices, Stay Set at Bending point & double stay at end point with 18 mm G.I.H.T.Stay, concreting of Stay with Anchor plate, guarding at Road crossings etc if required. including cost of all materials, labour transportation,inspection & commissioning etc. complete.

Commissioning of one number 25 KVA,11 /0.4 KV Double Pole mounted Substation with 5mtrx3mtrx1.5mtr height mesonary toe wall /G.I. Flat fencing boundary wall with Flat with Polymer insulator ,L.T Dist Box with MCCB , Aluminim bus bar of single bay with kitkat fuse , sand filling and metal spearding with M.S.Grill gate ,all Channel matrials should be G.I , 7 Nos earthing with chamber with 3mtr G.I pipe of 40mm dia with connecting of 50mmx 6mm G.I flat to all earthing including 25KVA BIS Leble-II Star rated Transformer confirming to RE Rules 1956, mounted on 3.0 Mtr. Long structure, supported in 300 kg 9 mtr long PSC pole,transformer hard channel & top channel made of 3.0 M long 100 X 50 X 6 mm G.I.Channel, Transformer belting on 3.0 M long 50mm X 50mm X 6 mm G.I.Angle, (all REC SPN Std.F-3) with all accessories like 3 pole 11 KV HG Fuse(F-5)& A.B.Switches(F-9) both mounted on 3.0 M long 75mm X 40mm X 6 mm G.I.Channel and supported by 1.0 M long 50 X 50 X 6 mm G.I.Angle, with 3 No. 11 KV Lightening Arrestors and Danger board at each Pole, Anti climbing Devices & all other necessary fittings i.e required size Nuts & Bolts, Brackets, Cable, Cable Sockets as per TPCOCL specification etc. including cost of all materials, labour , cess, transportation complete with liasioning for testing inspection & commissioning as per specification of TPCODL etc complete.

Labour for drilling a perfectly vertical bore hole of specified diameter (minimum 400 mm dia.) for a specified depth below ground level in alluvial soil strata by mud Rotary Rig drilling as required to suit the site condition as per the direction of Engineer in charge including use of own Rigs with its accessories, tools and plants and all consumables (like coir rope, cotton waste and bentonite powder etc. complete) etc. for lowering of 200mm dia GI/PVC Pipe for housing fitted with sockets and with or without well screen as per the necessity for the soft medium, hard and boulder formations (. GI/PVC casing pipes if required by the contractor to prevent collapse of over burden portion ) including lower and withdrawing of casing pipes after drilling 200mm to 450mm dia in over burden portion. Drilling for 200 (8”) dia pipe: From 0 mtr. to 100th meters

Supply of all Labour & T&P for lowering the following sizes of PVC Pipes with or without slotted pipes as per the necessity from ground level & fitted & fixed up in perfectly verticaly position inlcuding cutting & threading pipe and slotted pipe and fixing all jointing materials etc. complete. and keeping the top of the casing pipe threaded including plugging tube wells to prevent entry of foreign materials from above excluding cost of fitting & joining materials. 200mm dia PVC/GI Casing pipes

Cleaning and developing the production well using their own compressor continuously worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipments and labour as per the direction of Engineer-in-charge.

Supplying all materials,Labour T & P for packing the bore with washed gravel size (P-6) arround the well screen and pipes in good quality including cost of gravel ,conveyance,royality,etc complete as per direction Engineer-in-charge. (50m depth) =0.786 x (0.4² - 0.2²) x 50mtr = 4.716 say 4.7 cum

Labour charges for cutting Transverse slot on 200 mm dia pvc pipe with slot size 1.5 mm as per specification

Threading charges

8" PVC bail plug

8" PVC threaded end cap PN-10

200mm x 12" long PVC shot piece

200mm Ø SCHEDULE 80 casing pipe (As per EPM Rate Order No. 2877 dated 05.07.2025)

Please Enable Macros to View BoQ information