SPECIAL REPAIR TO BLDG NO MES-115 INCLUDING CERTAIN SANCTIONED WORKS AT SHILLONG UNDER GE SHILLONG.

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises etc complete all as specified and as directed by Engineer-in- Charge.

Dismantling plain or corrugated steel sheeting any guage thickness roof covering etc complete all as specified and directed.

Dismantling wall / ceiling boards of any description (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets etc complete all as specified and as directed.

Taking down chowkats or frames size n. exc. 1.5 Sqm each (without taking off shutters from the frame) with all builders hardware and removing from site etc complete all as specified and as directed.

Taking down chowkats or frames size exc. 1.5 Sqm but n. exc. 4 Sqm each (without taking off shutters from the frame) including all builders hardware and removing from site etc complete all as specified and as directed.

Taking down shutters of any description size n. exc. 1 Sqm each with all builders hardware and removing from site etc complete all as specified and as directed.

Demolition and breaking up drain pipes 150 mm dia (salt glaged ware AC or reinforced concrete/PVC pipe) set in cement mortar etc complete all as specified and as directed..

Dismantling wrought iron or mild steel work of any description not otherwise provided for. etc complete all as specified and as directed..

Demolition of plain cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) etc complete all as specified and as directed.

Demolition of plain cement concrete such as precast concrete blocks or of any description and in any position not otherwise specifically provided for,etc complete all as specified and as directed.

Dismantling PVC water storage tanks of capacity exc 500 litre but not exc 1000 litre etc complete all as specified and as directed.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section etc complete all as specified and as directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement sand mortar 1:6 etc complete all as specified and as directed

All as per above item No 13.00 here in above but as in vertical surfaces of wall such as skirting & dado over and including 10mm thick backing course using cement sand mortar (1:4) etc complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:6 etc complete all as specified and as directed.

All as per above item No 15.00 here in above but as in vertical surfaces such as skirting & dado over and including 10mm thick backing course using cement sand mortar (1:4) etc complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:6 etc complete all as specified and as directed.

M&L for Glazed ceramic colour tiles of size 300mm x 450mm x 7mm or 450mm x 300mm x 7mm thick in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 etc complete all as specified and as directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement sand mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed.

M&L for 2nd class hard wood Plain fillets square rectangular or tringular in section clean sawn on one face or edge in section wrought secured with nails or brads sectional area exc 13 Sqcm but n.exc 25 Sqcm complete all as specified and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour etc complete all as specified and as directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and as directed

S&F 4mm thick Non asbestos fibre cement Bldg Board fixed or laid / inserted to timber / GI / aluminium frame work with stainless steel screws as in ceiling etc complete all as specified and as directed.

S&F Anodised aluminium snap grid frame work for false ceiling comprising of aluminium perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using GI wire of 6mm thickness .GI frame will be 60 x 60 cm to recieve building board in ceiling etc complete all as specified and as directed .

M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC door frame of size 50 mm X 47 mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, etc complete all as specified and as directed .

S&F factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I complete all as specified and directed

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet/cup-board completed all as specified and directed.

S&F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised with width of flap ( when open) 30 mm etc complete all as specified and as directed.

S&F Magnet catcher for cup board shutter, brass body and striking plate including letting in complete all as specified and as directed.

S&F Extruded brass handles, 100 mm size, fabricated type, polished etc complete all as specified and as directed.

S&F 100 mm long Hasp and staple , safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with stainless screws etc complete all as specified and as directed.

S&F 35 mm thick flush shutter solid core construction with block board core and plywood face panels, decorative face veenered type on both sides etc complete all as specified and as directed.

S&F 35 mm thick, 2nd class hard wood, glazed and skeleton shutter, open rebated and prepared to receive glass or gauge without sash bars , divided in to squares and edges of framing plain chamfered or rounded, fitted with cut or mitred beads for securing glass or gauge etc as specified in SSR Part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 30 mm thick, 2nd class hard wood, glazed and skeleton shutter, factory made, open rebated and prepared to receive glass or gauge without sash bars , divided in to squares and edges of framing plain chamfered or rounded, fitted with cut or mitred beads for securing glass or gauge etc as specified in SSR Part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

S&F Aluminium alloy, anodised, sliding door bolt , 300 mm long ,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F Aluminium handle 150 mm long cast type anodised etc complete all as specified and as directed.

S&F Aluminium tower bolt (200 mm long), anodised barrel tower bolts of extruded section etc complete all as specified and as directed.

S&F Aluminium floor door stopper (150 mm long) of aluminium alloy body and tongue, anodised with hard drawn steel spring etc complete all as specified and as directed.

S&F Mild steel rat tail helical door spring (150 mm long) including roller and roller plate etc complete all as specified and as directed.

S&F Mild Steel Butt hinges, medium weight, cold rolled, 100 mm size ISI Marked etc complete all as specified and directed.

S&F Sheet glass, ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.50 sqm in each pane etc complete all as specified and as directed.

S&F in repair Sheet glass, ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.50 sqm in each pane etc complete all as specified and as directed.

S&F Figured sheet glass, ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.50 sqm in each pane complete all as specified and as directed.

M&L for Synthetic enamel paint two coats over a coat of pink primer on new or previously untreated wooden surfaces exc. 10 Cm width or girth including preparation of wooden surfaces complete all as specified and as directed.

S&F 25 mm thick flush shutter solid core construction with block board core and plywood face panels, decorative face veenered type on both sides .etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint laid in trenches or in floors including clamps for securing pipe complete all as specified and as directed .Make:- Prince / Supreme.

S&F 110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F 75 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint laid in trenches or in floors including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F 75 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

M&L for PVC (SWR) floor trap ,75mm outlet dia , plain with grating including jointing with solvent cement etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bend of any radius complete all as specified and directed.Make:- Prince / Supreme.

S&F 75 mm bore PVC (SWR) bend of any radius complete all as specified and directed.Make:- Prince / Supreme.

S&F 110 mm bore PVC (SWR) bend of any radius with access door complete all as specified and directed.Make:- Prince / Supreme.

S&F 75 mm bore PVC (SWR) bend of any radius with access door complete all as specified and directed.Make:- Prince / Supreme.

S&F MS works Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including distance pieces, cleats, plates, welding/rivets/bolts , Fe 410 -W (Gde E- 250) quality A etc complete all as specified and as directed.

S&F mild steel plates 6 mm thick (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe -410-W( Gde-E-250 quality-A) complete all as specified and as directed..

M&L for preparation of new or previously untreated steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M&L for 75 mm thick PCC (1:3:6 ) type C -2 ( using 40 mm graded stone aggregate as in Plinth protection and similar works , finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Cement Concrete type C1 1:3:6 (using 20 mm graded stone aggregate ) as in surface channels and drains including necessary formwork etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitred/stopped ends etc complete all as specified and as directed.

S&F rotational moulded polyethylene 1000 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

Taking up or down steel tubing with connections of 15 mm bore pipe including cleaning for refixing or removal from site with all fittings etc complete all as specified and as directed.

S&F GI tubing 15mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

Refixing of old serviceable steel water tubing obtained from taking down pipes against serial item no. 64.00 i.e. of 15mm bore but with new GI fittings in new or old position ( wall, ceiling or floor) etc complete all as specified and as directed

Taking up or down steel tubing with connections of 20 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

S&F GI tubing 20 mm dia medium grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

Refixing of old serviceable steel tubing obtained from taking down pipes against serial item no. 67.00 i.e. of 20mm bore but with new GI fittings in new or old position ( wall, ceiling or floor) complete all as specified and as directed

Cutting chases, pinning in concrete block or slab wall ,making good to facing where required and pointing in cement sand mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth etc complete all as specified and as directed.

S&F in repair Vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including PVC water closet seat cover closed pattern with flat bottom and cover with PVC hinge device, flushing pipe, fixing bolt for pedestal pattern and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Prayag cat part no.4022 or equivalent make of Parryware / Hindware.

S&F in repair PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat Part no. 503 or equivalent make of Pearl/ Hindware.

S&F Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat part no. 4645 IRIS or equivalent make of Pearl/ Hindware.

S&F PVC Connections 15mm size with PTMT nuts of length 450mm and fixed, complete all as specified and as directed.

S&F CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.7606 or equivalent model from make Sona / Hindware.

S&F 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

S&F 20 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

S&F in repair CP angular Stop valve ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe with or without lettered 'HOT' or 'COLD' etc complete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

S&F in repair 15mm bore CP wall mixer 3-in-1 system with provn for bath hand shower and overhead shower complete with 115mm long bend pipe , connecting Legs & wall flange (without hand & overhead shower) complete all as specified and as directed . Make - Jaquar continental series of cat part no.CON-281 KN or equivalent make in Prayag / Sona / Hindware.

S&F in repair 15mm bore CP centre hole basin mixer with pop up waste system with 450mm long braided hoses etc complete all as specified and directed (Make - Continental series of make Jaquar Cat No CON-169KNB or equivalent make of Prayag / Parryware / Hindware.

S&F in repair 15 mm bore CP health faucet (ABS body) with 8mm dia ,1.2 meter long flexible tube and wall hook etc complete all as specified and as directed (Make - Jaquar, Cat No - ALD-CHR-593N) or equivalent make of Prayag / Parryware / Hindware.

S&F in repair Corner glass shelf assembly with CP brackets etc complete all as specified and directed . Make:- Jaquar, Cat No ACN-1173 or equivalent make of Prayag / Parryware / Hindware.

S&F in repair Tubular Towel rail , D type 60 cm long brass between flanges ,Chromium plated etc complete all as specified and as directed.Make:- Prayag / Parryware / Hindware.

S&F in repair CP Towel Ring square or round fixed on wall with stainless screws etc complete all as specified and as directed. Make-Jaquar .continental series of Cat No ACN 1121N or equivalent make of Prayag / Parryware / Hindware.

S&F in repair CP Soap dish fixed on wall with stainless screws etc complete all as specified and as directed. Make-Jaquar continental series of Cat No ACN 1131N or equivalent make of Prayag / Parryware / Hindware.

S&F in repair CP Toilet roll holder fixed on wall with stainless steel screws etc complete all as specified and as directed. Make-Jaquar continental series of Cat No ACN 1151N or equivalent make of Prayag / Parryware / Hindware.

S&F kitchen or laboratory sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 510 mm x 430 mm x 203 mm bowl size 430 mm x 380 mm x 203 mm complete all as specified and directed.Make:- Prayag cat part no. 1218D or equivalent make of Nirali / Hindware

S&F in repair kitchen plate rack made of stainless steel sheet not less than 1mm thick of over all size 31'' x 30'' x 10'' fixed to wall with brass screws etc complete all as specified and as directed.Make:- Prayag Cat part no. P-346 or Bluestar cat part no. BSKPR-314 equivalent make of Hindware / Nirali.

S&F in repair decorative curtain rod (drapery rod) 20mm dia etc complete all as specified and as directed

S&F in repair curtain rod bracket decorative (Latto) etc complete all as specified and as directed

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved liquid Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a layer of 10 mm thick base coat including finishing the surface even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

M&L for Rendering, 10 mm thick plaster in cement sand mortar 1:6 including finishing the plastered surfaces even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of wall and applying two finishing coats of exterior emulsion paint ( weather coat ) over and including a coat of wall primer etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wall and applying two finishing coats of Acrylic emulsion distemper over and including a coat of wall primer etc complete all as specified and as directed.

M&L for complete removal of existing treatment of wall including cornices, pilasters etc and applying two finishing coats of Acrylic emulsion distemper over and including a coat of wall primer including necessary preparation of surfaces etc complete all as specified and as directed.

M&L for complete removal of existing treatment of wall including cornices, pilasters etc and applying two finishing coats of exterior emulsion paint ( weather coat ) over and including a coat of wall primer including necessary preparation of surfaces etc complete all as specified and as directed.

M&L for preparation of old or previously treated wooden surfaces exc. 10 Cm width or girth and applying a coat of Synthetic enamel paint including preparation of wooden surfaces complete all as specified and as directed.

M&L for complete removal of existing treatment of wall including cornices, pilasters etc and applying three coats of white wash including necessary preparation of surfaces etc complete all as specified and as directed.

M&L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregates) as in roof kerbs, sloping padding in roof slab or mud stops, rounded or chamfered on edges, finishing even and rough etc complete all as specified and as directed.

M&L for rendering 10 mm thick roof kerbs, sloping padding in roof slab or mud stops, rounded or chamfered on edges, in cement sand mortar (1:3) , mixed with water proofing compound @ 3% by weight of cement used, finished the plastered surface even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge.(WPC shall be measured & paid seperately) .

Supply only integral water proofing compound, ISI marked.complete all as specified and as directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg / Sqm including cleaning of surfaces etc complete all as specified and directed

Supply and laying APP membrame 3mm thick (minimum),ISI marked weighing 3.5 Kg/m² reinforced with polyster non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by forced application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction complete all as specified and as directed.

Taking down shutters of any description size exc. 1 Sqm but n.exc. 2 sqm each and removing from site with all builders hardware complete all as specified and directed.

S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including necessary joining cleat, hinges for fixing etc. complete all as speicified .

S&F Anodised aluminium window and ventilator shutters, powder coating (minimum thickness of powder powder coating 50 micron), fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges 100mm long (2 no.) suitable handle (1 no.) etc complete all as specified and as directed.

M&L for cast iron Nahani trap, 100 mm dia outlet, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified and as directed.

S&F in repair Water closet Pedestal pattern, single piece WC with UF soft close seat cover , hinges, fixing accessories set and accessories set, cistern fittings, size: 365 x 655 x 765 mm, P trap -180 mm etc complete all as specified and directed Make-Jaquar of LYRIC series Cat No LYS-WHT-38851P or equivalent make of Prayag / Hindware.

S&F in repairs Vitreous china WHB, wall hang basin with fixing accessires Size-590x490x185mm with fixing accessories set complete all as specified and directed. Make-Jaquar Lyric model Cat No 38801 including padestal for Cat No 38801.

S&F in repair Hand Shower 105 mm dia round shape single flow with air effect (ABS body & face plate chrome plated) with Rubit Cleaning System etc complete all as specified and as directed. Make - Jaquar, Cat No - HSH-1717 or equivalent make in Prayag / Hindware / Parryware.

M&L for Rendering, 10 mm thick plaster in cement sand mortar 1:3 on ceiling or chhajja including finishing the plastered surfaces even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of ceiling or chhajja and applying three coats of white washing including necessary preparation etc complete all as specified and as directed by Engineer-in-Charge.

Demolition of reed,lathing, single or double including battens and plaster or chicken wire lathing etc complete all as specified and as directed

Taking down plastering on lathing (other than wire-netting, without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered) etc complete all as specified and as directed.

Dismantling boarding of any description and fixed any position with nails etc complete all as specified and as directed.

M&L for 2nd class hardwood, 25 mm thick boarding, planed one side with butt joints fixed with nails as in eaves board / fascia complete all as specified and directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:6 complete all as specified and as directed.

S&F 35mm thick, factory made, 2nd class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt , 250 mm long ,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

M&L for Rendering 15 mm thick in cement sand mortar (1:6) on one side of lathing ,finishing even and smooth without using extra cement etc complete all as specified and as directed

M&L for Rendering 15 mm thick on other side of lathing in cement sand mortar (1:4), mixed with water proofing compound , finished plastered surface even and smooth without using extra cement etc complete all as specified and as directed (WPC shall be measured & paid seperately) .

M&L for preparation of new or previously untreated surfaces of wall and applying three coats of white wash including necessary preparation etc complete all as specified and as directed.

S&F wire netting of galvanised steel wire 0.71 mm dia and size of mesh 25 mm fixed with tinned tacks of GI wire staples etc complete all as specified and as directed.

S&F in repair Vitreous china squatting pan of Orissa Pattern of size 580x 440 mm ,white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag cat part no. 4055 or equivalent make of Parryware / Hindware.

S&F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) bue including spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimumweight 60gms) complete all as specified and as directed .Make:- Prayag cat part no. 4998 or equivalent make of Parryware / Hindware.

S&F in repair PVC Connections 15mm size with PTMT nuts of length 450mm and fixed, complete all as specified and as directed.

S&F in repair 15 mm bore stop valves, fancy type, chromium plated with long shank and cup ( concealed type) , screwed both ends for iron pipe or for unions and fixed, complete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

S&F in repair chromium plated. shower rose with arm for 15 mm bore pipecomplete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

S&F in repair Grating doom 100 mm dia of PTMT.(Minimum weight 25 gms) etc complete all as specified and as directed. . Make:- Prayag / Sona / Hindware.

Supply only liquid water proofing compound ISI marked etc complete all as specified and as directed.

Dismantling PVC(SWR) drain pipes up to 110mm dia, jointed in cement mortar and taking out of trenches , cleaning,if required, etc complete all as specified and as directed.

S&F PVC (SWR) 110mm bore branch piece, single (single Y) equal or unequal with access door etc complete all as specified and as directed. Make:- Prince / Supreme

S&F 110 mm bore junction single, (Single T) equal or unequal etc complete all as specified and as directed. . Make:- Prayag / Sona / Hindware. Make:- Prince / Supreme

Demolition of RCC of any description and in any position not otherwise specifically provided for including removal of debries from site etc complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

M&L for PCC (1:4:8) type D-2(using 40mm gr aggregate) as in foundation , filling and mass concrete etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for RCC M-25 ( design mix) using ( using 20mm graded stone aggregates ) as in footings, foundation beams; plinth beams; bases for columns, etc complete all as specified and as directed.

M&L for RCC M-25 ( design mix) using ( using 20mm graded stone aggregates ) as in columns, pillars etc. complete all as specified and as directed.

M&L for RCC M-25 ( design mix) using ( using 20mm graded stone aggregates ) as in beam, lintel band over 1.50m span. complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and as directed.

Formwork to sides of pillars, posts,struts,piers,columns and stanchions etc complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 5 mm dia and over and including 10 mm dia stirrups ,spacers and binders. , cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.410 or Fe-310.Gde-E-165 complete all as specified and as directed

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement sand mortar 1:6 etc complete all as specified and directed.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved liquid Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a layer of 10 mm thick base coat including finishing the surface even and smooth without using extra cement, with additional thickness is provided as floating /setting coat complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

M&L for mild steel works such as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and as directed.

S & F Galvanised 2 stand steel barned wire 2.24 mm dia barbed with 2 mm dia basbs at 75 mm spacings and stracing , fixing to any type of standard rails, straining bolts, incl securing on typing at crossing with and provisioning of galvanised mild steel wire, staples of steel pins etc.complete all as specified and as directed.

M&L for Granite (of any type) tiles 18-20 mm thick machine cut , bedded and jointed with grey cement and pointed with white cement with admixtures over and including 15mm thick screed bed in cement sand mortar 1:4 complete all as spefied & directed

E&M WORKS M&L for Point wiring with two single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked), green colour as continuous earth wire terminated connected to common earth dolly for one light / fan point controlled by one way switch including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge .Make of cable:- KEI / RR Kabel / Havells . PVC Casing & Capping:- Prestoplast / Finolex / Kalinga

All as per item No 155.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as directed by Engineer -in -Charge .

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5/6 Amps complete all as specified and directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F Decorative wall mounted LED batten fittings with all accessories, 1X18 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed. Make Havells Cat part No. LHEXBQP71N1W018 or Make:- CROMPTON Cat Part No. LCTL 18 CDL.or Philips cat part no. DX UJJWAL.

S&F Decorative wall mounted LED batten fittings with all accessories, 1X 9 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed Make :- Crompton Cat part No. LCTL-9-CDL or Make:- Havells Cat part No. LHEXBQP7IN1W009.

Supply & fixing Exhaust fan, heavy duty , single phase, AC, 230/240V of 250 mm ( 10'') sweep ,Ventil DX, including cutting hole ( circular / rectangular ) in brick wall and making good to disturbed surface with Cement sand mortar 1:4) and necessary painting work to match with the existing wall etc complete all as specified and directed. Make:- Havells / Bajaj / Philips.

Supply and fixing LED Building security light 10/25 watt ,pressure die cast aluminium housing heat resistant glass, IP 65 protection, better optics for uniform distribution complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light including suitable size bracket and necessary electric connection etc complete all as specified and as directed.Make:- Bajaj cat part no. 169821 LED or CG cat part no LSTO 25 CDL equivalent make of Philips / Havells.

Supply, fixing and testing , electrically driven water heater (Geyser) , storage type, BEE 5 star rating , 25 litre capacity , grouting in brick wall with new GI nut & bolts of suitable size including necessary incoming and outgoing electric and water connections with hot / cold PVC pipes suitable for geyser etc complete all as specified and directed. Make: Havells product code GHWCANTWH025 or equivalent to Bajaj / Venus / Racold

Supply, fixing heat resistant PVC connection suitable for hot and cold water, 450 mm long 15 mm dia etc complete all as specified and directed. Make: Polytuf / Prayag / Sona.

Supply and fix MCB Distribution board , 240 volts Single pole and neutral ,double door, sheet steel enclosure ,powder coated with 100 Amps rated busbar with neutral link, 4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer -in- Charge . Make : Make: Havells, Cat Part No:DHDPSHODRW04 or equivalent model from make:- Siemens / Schneider / Legrand / L&T.

Supply and fix Isolator MCB DP, 240 Volt, 32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make: Havells Cat Part No:DHMCCDPF006-32 or equivalent model from make:- Schneider / Legrand.

Supply and fix MCB SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed . Make: Havells Cat Part No:DHMGCSPF006-32 or equivalent model from make:- Schneider / Legrand.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, .(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR cable/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I etc complete all as specified and as directed.

M/S P.K Nag Choudhury

M/S T N CONSTRUCTION

M/S BISWA CONSTRUCTION

MS HO Shadap

M/s M.L Consortium

M/s Nishi Kumar Das

M/s J. C. CONSTRUCTION