Providing and Fixing Kerb Channel and Paver Block after dismantling the existing Damaged Kerb Channel and Paver Block in front of Rock Garden and Bridge at Kaimbwala Chandigarh Ch to Mtc of Roads

Dismantling of Exsiting Rubber Moulded Cement Concrete paver & Stacking the same at site carefully complete in all respect and to the entire satisfaction of Enginner-in-Charge. N.S.

Dismantling of existing Kerbs and stacking the serviceable kerbs properly at site and disposal of the unserviceable kerbs average lead of 1000 mtr. N.S.

Dismantling of existing Channel and stacking the serviceable Channel properly at site and disposal of the unserviceable kerbs average lead of 1000 mtr. N.S.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 4.1.3

Providing, laying, spreading and compacting granular sub base material 150 mm thick compacted of natural sand, morrum, gravel crushed stone or combination thereof as per MORT&H specification confirming to clause 401 coarse graded grading – 3 as per table 400.1 of MORT&H specification, including spreading on the prepared sub grade with the help of tractor with planner of adequate capacity maintaining the requited slope and grade during operation, rolling with road roller 8-10 tone with the grade and cross fall (camber) to be checked and any high spot or depressing which becomes apparent, corrected by removing or adding fresh material, including cost of tools and plants, carriage of material from stacks, templates, barrier, lighting arrangement at night, chowkidar and maintenance of diversion etc. complete in all respect as per MORT&H specifications, density of GSB as laid 2 gms/cc complete in all respect and to the entire satisfaction of Engineer in charge. N.S.

Providing and fixing 80 mm thick ISI approved high density rubber moulded precast cement concrete paver blocks grey / coloured designer, polished (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M-35 duly ISI Marked including best quality of colour and hardening agent. The pavers should be complied with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to wear as per IS:1237-1980. The paver should be laid over a layer of 25 mm thick fine sand to the required slope and filling the joints with fine sand etc. complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S.

Providing and fixing 60mm thick high density rubber moulded precast cement concrete pavers block grey /coloured/ designer polished (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M-35 duly ISI Marked including the cost of best quality colours and hardening agents. The paver should be complied with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 (specification for cement concrete floor tiles). The paver should be laid over a layer of 25mm thick screened sand to the required slope and requirement complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S.

Providing and fixing of factory manufactured precast concrete kerb of size 300mm x 300mm having 150mm thickness with one edge semi rounded duly vibrated mechanically and compacted made of P.C.C 1:2:4 duly cured and finished. The rate further include filling of joints between kerbs / channels with cement mortar 1:2 complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S.

Providing and fixing of factory manufactured precast concrete channel of size 300mm x 300mm having 75mm thickness duly vibrated mechanically and compacted made of P.C.C 1:2:4 duly cured and finished. The rate further include filling of joints between kerbs / channels with cement mortar 1:2 complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S.

Providing and fixing of factory made Fine Finished Cylindrical Bollard 150mm dia Fiber Reinforced Plastic moulds of size 950mm (Precasted in M35 concrete) high over ground level and 300mm (Cast in situ with 1:2:4 Concrete) below G.L. made with M:35 mix concrete design using 1225 mm long 4 nos. 10mm dia TMT steel bars, 6mm dia stirrups @ 150mm c/c consisting 2 cuts of 75mm high at top for retro reflector tape type-IV, fiber reinforcement plastic moulds fixed in existing cycle track after digging of bituminous/concrete/ paved/earth having size 300x300x 450 mm also embeded in C.C.1:2:4 block of size 300x300x450 mm The rate included rectroreflective tape type IV, digging, centering shuttering wherever required,loading unloading with all leads, concrete etc complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S.