Special Repair of Civil Hospital and Residences at Safidon in Jind Distt. (Only for Society)

Amount

Dismantling brick work, tile masonry or tile lining and tile terracing in cement (HSR 8.5-b)

Dismantling concrete reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR 8.6-e)

Dismantling roofing mud roofing with wooden black laid over battens (HSR 8.8-c)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled (HSR 8.18-a) (a) Doors

Windows

Scraping of cement plaster (HSR 8.32-c)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Pre-cast cement concrete 1:2:4 with stone aggregate 20mm nominal size in kerbs and the like items finished smooth with 6mm thick cement plaster 1:3 on exposed surface including from work placing and fixing in position complete at the ground level or in first storey. (HSR 10.77)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in fasicas, parapets and other thin vertical sections, not covered by item no. 10.82, 10.86 to 10.88 not exceeding 10 cm thickness thickness excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects. [HSR. 10.89 + 10.95 (a)]

Providing and laying 80mm thick ISI marked interlocking paver blocks conforming to IS 15658:2006/IRC:SP:63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect (HSR 10.159) (Note:- Reputed make paver block only ISI marked will be used as approved by Engineer-in-charge).

First class brick work laid in cement sand mortar 1:6 in 1st storey upto 4 metre above plinth level. (HSR 11.7)

Tile terracing with one layer of tiles, 22.86cmx11.43cmx 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.14)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16. (HSR 13.50)

Bottom khurra on ground 1.2 m x 0.6m consisting of brick on edge laid in cment mortar 1:3 over 75mm c:c 1:8:16 including 12mm thick cement plaster 1:3. (HSR 13.57)

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (a) 100mm dia PVC pipe 6 kg pressure. [HSR 13.89-a]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

(b) 150mm dia PVC pipe 6 kg pressure. [HSR 13.89-b].

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. (a) 100mm dia PVC bend. [HSR 13.90-a]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

(b) 150mm dia PVC bend. [HSR 13.90-b].

Precast chequered tiles of 20 mm thickness In ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (Note:- Reputed make Tile Only ISI marked will be used as approved by Engineer-in-charge). [HSR 14.45+Note]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.89) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing vitrified tiles of size 600mm X 600mm of approved make in skirting/dados laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS. (HSR 14.90) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring laid in any pattern as specified over base of 20mm thick cement course sand mortar 1:3 of jointed with white cement slurry mixed with pigment to match the shade of tiles. Note: Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK (HSR 14.91)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (a) Size of ceramic Glazed tiles 200 x 300 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used as approved by Engineer-in-charge. [HSR 14.92(a)]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12mm thick cement plaster on walls (1:6). (HSR 15.7).

Painting one coat with synthetic animal paint in all shades on old wood work or metallic or plastered or concrete curfaces to give an even shad including rubbing down old paint. (Note;- First quality paint/primer of reputed make firm such as goodlass-Nerolac, Berger, Garware, Jenson, Nichoklson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, drum of paint shall be opened in presence of Engineer-in-Charge). (HSR 16.7) Through Rate

Applying priming coat with cement primer in all shade on newly platered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.25) Through Rate

Distempering with washable oil bound distemper (of approved manufacture) one coats on old distempered work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.59) Through Rate

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (a)]. 2nd Quality Through Rate

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81) Through Rate

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock & Champ only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood nd including cost of iron hinges, screw, chock/cleats, stops nails etc. complete in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (b) 35 mm thick. [HSR 17.90 (b) - Note 1 under 17.18].

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock & Champ only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (ii) 35 mm thick. [HSR 17.92 (ii) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a-iii) 35mm thick - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Supplying and fixing Glass panes including special metal sash putty of approved make. (b) glass panes 4 mm thick, exceeding 40 sq. dm areas. [HSR 18.30 (b)].

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (a) Door and window frame of size 89mm x 50mm with 40mm wide single rebate.(HSR 18.34-a)

Steel reinforcement TMT bars FE-500/EQR/FE-500 D grade or more for RCC work, where no included in the complete rate or RCC including straightening, bending, binding wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Providing and laying granular sub base consisting of drainage layer confirming to Table 400.1 Grading –VI of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRT&H specifications. Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer. (N.S.)

Providing and fixing in position best Indian make Indian type orissa or orya water closet suite for sinking into floor, with raised foot treads complete with complete with 100mm H.C.I. 'P' trap with or without vent as required and all other necessary fitings as fully described in item no. 30.1 above. (a) size 580mm (i) White (HSR 30.2 a-i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary Fittings as fully described in item no. 30.3 above. (HSR 30.4-i) white

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described item No. 30.51 above. (HSR 30.53-a) 600 mm x 450 mm x 200 mm

Providing and fixing in position best Indian make soap dish fixed into wall CP brass screw and complete in all respects including cutting and making good the wells etc. (a) CP brass. (i) Soap dish 160 mm (HSR 30.70 a-i)

Providing and fixing in position best indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. Chormium plated brass screws and washers over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with c.p. brass screws (as required by the engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian make (i) size 600mm x 450mm (HSR 30.71a (i)

Providing and fixing in position 15mm i/d CP brass bib cock of best quality (as required by the Engineer–in–Charge) (a) Bib cock long body.(HSR 30.75-a)

(c) Bib cock

Providing and fixing HDPE water storage tanks of sintex, Diplast. O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of building including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-charge (except civil work) (HSR 30.119) 500 ltr. capacity

Providing and fixing in position best Indian make C.P. Brass inlet connection 15mm with 375 mm pie and C.P. Brass nuts.(HSR 30.83)

Providing and fixing G.I. pipe complete with G.I. fitting and clamps, i/c cutting and making good the walls etc. Internal work Exposed on wall (DSR 18.10) (i) 15mm internal diameter of pipeline

20mm internal diameter of pipeline

Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- i) Wooden Batten @ Rs. 50/- Each

Brick Tiles @ Rs. 4.50/- Each

Brick Bats @ Rs. 450/- per cum

Good Bricks @ Rs. 4.00/- Each

Brick Bats @ Rs. 450/- per cum

Doors @ Rs. 500/- Each

Windows @ Rs. 500/- Each Note: All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

THE BALAJI CO OP L AND C SOCIETY LTD KHARKHANA JIND

The Sant Nagar Co-op L&C Society Ltd. Distt. Jind

The Khokheri Coop LandC Society Ltd.