Repair/ Maints to pump motor valves, water supply system, repalacement of U/S pipe lines of including connected accessories and day to day maint work and fire fighting system including connected equipment accessories at FAD Depot area Bharatpur

Amount

Repair/rectification of leakages to water supply distribution lines 40 mm dia to 80 mm dia GI tubing with provision of necessary excavation, returning and filling in as required, tightening of loose joints of union, elbow, sockets etc, threading if required including replacement of GI unions/sockets/elbows/nipples etc as required at site complete all as specified and directed.

Attending break down of water supply pipe line and repair to CI/DI/GI water mains of size 80 mm to 150 mm dia at a given notice including necessary excavation in mud, in any type of soil by manual or using special T &P etc. De-watering from the trenches by using pump sets, rectification of leakages, fixing of CI specials such as collars bends/tail peaces etc and making joints complete all as specified and as directed.

Attending break down of water supply pipe line and repair to CI/DI/GI water mains of size 200 mm to 300 mm dia at a given notice including necessary excavation in mud, in any type of soil by manual or using special T &P etc. De-watering from the trenches by using pump sets, rectification of leakages, fixing of CI specials such as collars bends/tail peaces etc and making joints complete all as specified and as directed. (Note for srl item Nos 1 to 3:-(a) CI fittings, lead Joints etc shall be measured and paid separetely. (b)The cost of excavation / earth work and repairs to damaged roads, existing structure etc shall be deemed to be included in the quoted unit rate (c) The quoted rated is deemed to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Military station under AOR of GE Bharatpur. (d) Work will be carried out in any area under juridiction of GE Bharatpur.

Supply and replacement MS clamp /saddle piece made out of MS flat iron suitable to make ferrule and clamping for branch connections complete with GI socket welded it on one FI strip suitably positioned at the centre of pipe including drilling as per site requirement complete with MS nuts, bolts, washers and rubber packing for complete for following sizes of pipe:

150 mm bore

100mm bore.

80mm bore.

M&L of run lead joint to CI spigot and socketed pipe of bore 80 mm dia complete all as specified and directed

All as per Item No. 05 but of size for 100 mm CI pipe

All as per Item No. 05 but of size for 150 mm CI pipe

All as per Item No. 05 but of size for 250 mm CI pipe

S & F attending bends tapers any type, (straight, bend, increasing, decreasing or double socket etc). Tee pieces single branch "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs of CI fittings upto 250 bore complete all as specified and directed.

Excavation of trenches in any type of soil n.exc 1.5 M wide and n.exc 1.5 M in depth for taking out / laying of pipe lines and getting out in soft/loose soil forming bottom surfaces to required gradients complete all as specified and as directed.

Returning, filling in and including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed

Removing excavated surplus materials to a distance not exceeding 50 Mtrs and deposited where directed at a level not exceeding 1.5 Mtr above starting point complete all as specified and directed.

Taking up or down G.I. tubing and connection and stacking neatly for reuse and removing the balance material from site of size 20 mm bore complete all as specified and directed.

All as per Item No.13 above but 25 mm dia.

All as per Item No.13 above but 40 mm dia.

All as per Item No.13 above but 50 mm dia.

All as per Item No.13 above but 80 mm dia.

S&F GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 20 mm bore complete all as specified and directed.

All as per Item No. 18 above but of size 25 mm bore .

All as per Item No. 18 above but of size 40 mm bore and -ditto-

All as per Item No. 18 above but of size 50 mm bore.

All as per Item No. 18 above but of size 80 mm bore.

M&L in repairs gun metal gate or globe valves with iron wheel head (ISI Marked), screwed both ends for iron pipe and fixed of size 20 mm bore complete all as specified and directed.

All as per Item No. 23 above but of size 25 mm bore

All as per item no 23 above but 40 mm bore.

All as per item no 23 above but 50 mm bore

Carryout of surface dressing/ site cleaning not exceeding 15 cms deep in soft / loose soil including removal of brick/stone pieces, herbs, shrubs and vegetation complete all as specified and directed.

Taking out the unseviseable CI pipe lines including all fittings with spigot and socket ends and lead joints including burning out joints and recovering lead and cleaning the pipes internal/external for reuse the following bore of pipes:-

100 mm bore

150 mm bore

250 mm bore

Refixing and laying only cast iron pipe with spigot end socketed any class in available length obtained from item No.28 tested complete in trenches all as specified and directed for the following bore of pipe:-

100 mm bore

150 mm bore

250 mm bore

Supply, laying in trenches, under floor, under road, connecting, jointing and testing ductile iron pressure pipe centrifugally cast ISI marked with socket and spigot ends confirming to IS-8329/2000 standard length of K-7 specification with outside zinc coating complete including necessaary rubber gasket joints complete of the following sizes : Note :- (i) Excavation and earth work will be measured and paid separately. (ii) Rubber gasket joints shall be deemed to be included in quoted rate.

100 mm bore

150 mm bore

250 mm bore

construction of brick masonry vavle pit of internal dimension 90cmx90cmx90cm depth with sub class "B' bricks in cm (1:4) and 10 mm thick plastering in CM(1:4),PCC (1:4:8) type D2 (Using 40mm grade broken stone aggregate) as in foundation lean concrete PCC (1:3:6) type CI (Using 20mm grade broken stone aggregate ) as in bedding and copping MS frame with 40x40x6mm angle iron 3 mm thick MS sheet cover plate with locking arrangement, hinges and two coats of sythetic enamel paint over one coat of red oxide primer including preparation of surface three coats of white wash on plaster surface (exposed to view) including necessary excavation in soft loose soil returning filling in and removal of surplus soil to a distance not exceeding 50 m complete allas specified and directed.

S&F in replacement of sluice valve 80 mm bore class PN-I with flanged and iron wheel head, shut and open directed cast on it and including jointing materials, rubber gasket suitable size nut bolts and washer etc complete all as specified and directed.

All as per item No.32, above but of size 100 mm bore

All as per item No.32, above but of size 150 mm bore

All as per item No. 32, above but of size 250 mm bore

supply and fixing in replacement of non return valve/ Air Release Valve, flanged ends PN I ISI Marked of 100 mm bore complete all as specified and directed.

Supply only Water treatment Calcium hypo chloride calcium based high strenght granular chlorine having 65%-70% chlorine content packed in 45 kgs PVC sealed container superior quality suitable for treatment of drinking water ( Much more stable than chlorine gas bleachig power and sodium hypochlorine ) all as specified and directed by Engr in charge. Note : - i) Approval of chemical (calcium hypochloride) shall be given after varification of test certificates of chemical of various manufactures and other like chemical and safety and health hazard aspectes of usage of chlornation ii) The branch and Make of the chlorineation of chemical must be stated in production and certified by govt laboratory confiming compliance of specfication of suitable for drinking water with a decleation from the laboratorythat from the technical strengh stability health safety and operation point of view this product is used for drinking water applicationfor cunsumption by humans and the brand /make of calcium hypo chloride is suitable for drinking water chlorination and its sample has been tested by govt laboratory.

Attending water sample in suitable bottle for testing of bio and chemical each test Ph, Tutbidity, Total dissolved soilds, Aluminium, calcium, chloride, Flouride, all specification as per IS 105009(2012) for the following locations:-

Semi underground sump 100000 Glns capacity at Mallah pump house

Overhead reservoir of 50000 Glns capacity at sewar Fort

Semi underground sump 50000 Glns capacity at KLP Area

Perimeter area Tube Well No 07

Semi underground sump 100000 Glns capacity at Madoni hills

Overhead reservoir of 75000 Glns capacity at kanjoli line

Dismantling of sluice valve of size 250 mm dia from existing pipe line and remove the spindle and inner gate and replace with new stainless steel spindle and require lathe work for inner gate at work shop and re- assembling the valve on its original position and testing complete all as specified and directed.

All as per above item No 39 but of size 150 bore

All as per above item No 39 but of size 100 bore

All as per above item No 39 but of size 80 bore

Cutting of existing road/PCC path for laying of pipe line complete all as specified and directed

M&L of PCC 1:2:4 type D-2, 40 mm graded aggregate filling and mass concrete, road finishing, trust/protection blocks for pipe lines/ installation damaged PCC paths concrete all as specified and directed

Disconnecting of electric motor 3 phase, any type from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the motor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 30 HP including painting complete all as specified and directed.

All as per item No.45 above but of capacity 10 HP electric motor any type.

Disconnecting of electric motor single phase, any from submersible pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the motor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 03 to 05 HP including painting complete all as specified and directed.

Dismantling centrifugal pumping set of 100 HP capacity DSM after disconnecting electric supply complete to carry out the repair/replacement of UNSV/worn out spare parts, nuts bolts, washer etc and re-assembling the pump sets on its original position and testing for its proper functioning. Note : Spare parts for repairing and making functional shall be measured and paid separately against respective items.

Supply only coupling CI (set of 02 Nos).

Supply only bearing DE/NDE for 100 HP pump set.

Supply only rubber bush tapper/barret type ISI marked.

Supply only shaft GM sleeves for pumps.

Supply only bearing housing.

Supply only key for impeller MS.

Supply only vent valve brass.

Dismantling centrifugal pumping set of 30/50 HP capacity DSM after disconnecting electric supply complete to carry out the repair/replacement of UNSV/worn out spare parts, nuts bolts, washer etc and re-assembling the pump sets on its original position and testing for its proper functioning. Note : Spare parts for repairing and making functional shall be measured and paid separately against respective items.

Supply only coupling CI (set of 02 Nos).

Supply only bearing DE/NDE for 30/50 HP pump set.

Supply only impeller CI suitable for 30/50 HP pump set

Supply only impeller ring suitable for 30/50 HP pump set

Supply only rubber bush tapper/barret type ISI marked.

Supply only shaft for pump stainless steel.

Supply only shaft GM sleeves for pumps.

Supply only bearing housing.

Supply only key for impeller MS.

Supply only vent valve brass.

Dismantling centrifugal monoblock pumping set of 05/10 HP capacity after disconnecting electric supply complete to carry out the repair/replacement of UNSV/worn out spare parts, nuts bolts, washer etc and re-assembling the pump sets on its original position and testing for its proper functioning. Note : Spare parts for repairing and making functional shall be measured and paid separately against respective items.

Supply only bearing DE/NDE for 05/10 HP pump set.

Supply only impeller CI suitable for 05/10 HP pump set

Supply only rubber bush tapper/barret type ISI marked.

Supply only shaft for pump stainless steel.

Supply only shaft sleeves for pumps.

Supply only bearing housing.

Supply only key for impeller MS.

Supply only vent valve brass.

Supply only mechnical seal

Taking out submersible pump pumping set of any capacity including suction pipe of any length and any dia from base well of any dia and lowering the same after necessary repair including water supply and electric supply connection and including transportation from site to work shop & testing complete. Note : Repairing of pump set will be measured and paid separetely.

S&F spare parts for submersible pump sets capacity 7.5 HP to15 HP as under :- Shaft bush.

Coupling

Thrust plate.

Neck ring.

Impeller distance bush.

Impeller key.

Impeller.

Thrust bearing.

Bush Stainless steel for impeller.

Bush GM for Rotter.

Shaft stainless steel for pump

Guide/distance bush GM.

Nipple stainless steel flange type for NRV

Sand guard.

Wireless water level monitoring device supply and installation with complete testing of wireless water level monitoring device Operating on single phase display level in meter/cm, acuracy of sensor is 1cm, electromechanilly sensor is installed on tank and connect with transmitter system via cable. transmitter installed at suitable location, transmitter send data to server via internet and show level in android app capacity of measure level is 7 meter of water all system fit in 18 gauge sheet box app will show water level of tank tank name capacity of tank over vflow value, last reading update time etc and marking device functional with providing sim card with 1 year charge all as specified and directed.

M&L submain wiring complete with 2X 2.5 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor and one run of 2.5 Sqmm copper cable for earth continuity conductor and including rigid PVC conduit with all PVC accessories fixed on concealed surface complete all as specified and directed.

Supply and fixing of Lithium base Energy efficient integrated Solar street light of 32 watt in single FRP body duly polyurethane coating (Camouflage color), encases with monocrystalline solar PV panel of 65-67Wp,lithium battery 11.1/12.8V,33.0 AH with inbuilt BMS,IP 65, High brightness W-LED(160-180lm/watt) lamp with Aluminium reflector for better light distribution ,CRI>70, color temp 5700K-6500K Microcontroller based charge controller cum driver,automaticdimming function(First 04 hrs at full brightness & rest of the time at lower light level with PIR motion sensor), Dusk to dawn operation,suitable to working temp (-) 10C to (+) 55C ,weight not more thatn 16-18 Kg with adjustable MS clamp suitable for pole/wall mounting etc complete as required including taking out old unserviceable street / wall light fittings .Make: AXXON/HAVELLS/PHILLIPS Protections: Short circuit, overload,Reserve polarity and battery protection.Firm should provide vital parametres Test report from NABL accredited lab and should be of made in India with CE & ROHS complaint. (Excavation & earth work shall be measured separately)

Dismantling the submersible motor from pump set and rewinding the motor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 12.5/15 HP including painting complete all as specified and directed.

Dismantling the submersible motor from pump set and rewinding the motor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 3 HP/5 HP up including painting complete all as directed.

Supply and lowering in replacement of old rusted GI Column Pipe 3 mm long wit 2 nos of flanged heavy grade of size 50 mm dia flange type with nuts, bolts of both ends in the bore/open wells complete all as specified and directed.

Supply and laying of High density poly- ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 for column pipe to bore well of size 75 mm dia including necessary arrangements for coupling arrangement on top and bottom of HDPE pipe with pump and delivery pipe complete all as specified and directed.

S&F in replacement of PVC insulated submerssible cable water proof flate type 3 core with standed copper conductor cable, 6 Sqmm, 1100 volts grade including cable lugs/joints, connection to submerssible motor and other end to aluminium armoured cable including jointing complete as directed .

S&F in repairs fully automatic star Delta starters in sheet metal enclouser suitable for 15 HP capacity, 415V, 50Hz,complete all as specified and directed. Make : L&T/BCH/Siemens

S&F in repairs pressure gauge, 100 mm size, fitted on delivery side of pump set , including dismantling the old one complete all as specified and as directed.(Make : H-Guru/Fiebig)

M/S KAMAKHYA CONTRACTORS

PD GUPTA AND COMPANY

rohan traders

GANGA CONSTRUCTION

M/s Ranaji Construction Co

S S TRADERS