Execution of Construction works under CSR and SD for the Protection and Restoration works for Historical Chogan adjacent to zonal hospital Chamba, Distt-Chamba (HP), (Pkg. No. C-814).

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Excavation in foundation trenches etc., in earth work, lift upto 1.50 mtrs., stacking the excavated soil not more than 3 mtr., clear from the edge of excavation and then returning the stacked soil in 15 cm. layers, when required in to plinths sides of foundation etc, consolidating each deposited layer by ramming and watering and disposing of all surface excavated earth as directed within alead of 20 meteres. Jumper Work.

Stone filling behind retaining walls.

Providing and laying cement concrete 1:4:8 ( 1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of from work in foundation and plinth.

Prvoiding form work with steel plates 3.15 mm thick welded with angle iron in frame 30 X 30 X 5 mm, so as to give a fair finish including centring, shuttering strutting and propping etc., with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Foundation, footings basis of columns etc. and mass concrete.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth (Crushed arrgegate)

Repairs to plaster in patches of 2.50 Sq.M. and under and 10 to 15mm thick including cutting the patch in proper shape and replastering the surface of the wall including disposal of rubbish to the dumping ground within a Lead of 20 metres with:-Cement Mortar 1:6 (1 Cement : 6 Sand)

Stone tile (Polished) work for wall lining over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slury @ 3.30kg/sqm including pointing in white cement complete. 8mm thick. Granite of any colour and shade.

Providing and laying factory made chamfered edge Cement Concrete interlocking paver blocks with acrylic coating in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting fixing in position and applying a priming coat of red lead paint - In trusses and trussed purlins in buildings.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & tainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Painting two coats (excluding priming coat)on new steel and other metal surfaces with readymixed paint acid resisting brushing to give an even shade including cleaning of all dirt,dust and other foreign matter.

Painting one coat (excluding priming coat) on previously painted steel & other metal surfaces with readymixed paint,brushing oil, grease to give an even shade including cleaning the surface of all dirt,dust and other foreign matter :- With readymixed paint other than white.

Extra over item No. 14 for every subsequent finishing coat of paint :- With readymixed paint other then white.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered material

40 mm thick matble chips flooring rubbed and polished to granolithic finish, with under layer 30 mm thick cement concrete 1:2:4 (1 cement :2 sand: 4 graded stone aggregate 10 mm and down gauge) and top layer 10 mm thick with marble chips of required sazes laid in cement marble powder mix 3:1 (3 cement : marble powder by weight) in proportion of 4:7 (4 cement marble powder mix : 7 marble chips by volume). Medium shade pigment with approximate 50% white cement and 50% ordinary cement (in top layer only).

Writing letters or figures on any surface with black japan paint (stops,comas,hyphens and the like not to be measured and paid separately) Block letters/figures

Providing and fixing of Stainless steel Bench (4 seater)

Providing and fixing of Stainless steel Bench (3 seater)

ROSHAN LAL THAKUR

sonakshi buildtech pvt ltd