Repair to toilets, flooring, Aluminium doors/windows, hand rails, OBD and painting at AF Station Deolali.

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed.

Demolition of cement concrete on ground floors n exc 15 cm thick above GL all as directed.

M & L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate ) as in flooring finished even and rough all as specified and as directed.

M & L for coloured joint free non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floors etc. set and and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) finished even and rough to receive the top layer all as specified and as directed.

M & L for coloured (light shade) vitrified ceramic tiles 10mm thick joint free (Square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match and the shade of the tiles including 15mm screed bed or bedding layer CM 1 : 6 all as specified and as directed.

M & L for coloured (dark shade) vitrified ceramic tiles 10mm thick joint free (Square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in floors as in decorative purpose, border etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match and the shade of the tiles including 15mm screed bed or bedding layer CM 1 : 6 all as specified and as directed.

M & L for coloured (light shade) vitrified ceramic tiles 10mm thick (Square/rectangular) polished, area of each tiles n. exc 0.36 Sqm in skirting/dados, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles including 10 mm thick rendering in CM 1:4 all as specified and as directed.

M & L for coloured Glazed ceramic tiles in vertical surface 300x 450x 7 mm/ 300X 600X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with pigment to match the colour of tiles over and including 10 mm thick rendering/bedding layer in CM 1:4 on brick work /stone masonary or concrete surfaces.

M&L for 75 mm thick sub base in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregates) all as specified and as directed.

M&L Chequered cement concrete tiles rubber moulded 30cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floors, with grey cement and pigments over and including 15 mm thick screed bedding in CM 1:6 all as specified and as directed.

M & L for plain/reinforced cement concrete Type B-1, 1:2:4 (using 20 mm graded granite stone aggregate) cast in situ in copings, bed plates and the like including weathering, slightly rounded or chamfered angles & throating and including use of necessary form work all as specified and as directed.

Demolition of Brick/Stone masonary built in cement mortar all as directed.

M & L brick work with fly ash brick straight or curved on plan exceeding 6 metres mean radius built in cement mortar 1:6 all as specified and as directed.

M & L brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 all as specified and as directed.

Taking down cement plaster on brick/stone walls/ concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc all as directed.

M & L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work of walls in cement mortar 1:4 finished even and smooth all as specified and as directed.

M&L for rendering 15mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth all as specified and as directed.

M&L for rendering 5mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:3 finished even and smooth on ceiling all as specified and as directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over one coat of alkali resistant priming paints or JK wall Care Putty of 2mm thick suitable for external surfaces all as specified and directed by Engineer-in-Charge.

M & L for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion after chalk whiting on plasterred surfaces or one coat of JK wall care putty of 2mm thick all as specified and directed by Engineer-in-Charge.

M & L for preparation of newly plastered surface and applying three coats white wash in ceiling all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of walls by steel wire brushing, preparation of surfaces and applying two coats of distemper oil emulsion after chalk whitening or JK wall care putty 2mm thick over the walls all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces of walls and applying one coat of oil emulsion distemper all specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of walls by steel wire brushing, preparation and applying two coats of cement based paint over one coat of alkali resistant priming paints or JK wall Care Putty of 2mm thick suitable for external surfaces all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces of walls and applying one coat of cement based paint all as specified and directed by Engineer-in-Charge..

Complete removal of existing treatment of ceiling by steel wire brushing, preparation of surfaces and applying three coats of white wash on ceiling all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment by steel wire brushing and applying two coats of weather coat paint APEX over one coat of alkali resistant priming paints or JK wall Care Putty of 2mm thick suitable for external surface all as specified and directed by Engineer-in-Charge.

Dismantling of stone slabs and tiles of any description of thickness in floors, aprons etc laid bedded and pointed in any mortar all as directed by Engineer-in-Charge.

M&L Machine cut cudappah stone slab 20mm to 25 thick, over 15mm thick screed bed including cement slurry laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete necessary cutting, notching etc for sink all as specified and directed by Engineer-in-Charge.

M&L granite (of any type or any position) work ( table rubbed & polished), 18 to 20mm thick, in steps, jambs, pillars, window-cill, cooking platforms & like in cement mortar (1:4) including polishing of chamfered edges and pointing in white cement using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM (1:6) necessary cutting, notching etc for sink all as directed by Engineer-in-Charge.

Chamfer, splays, or arris in facework of granite exc 15mm wide but nexc 50mm wide all as directed by Engineer-in-Charge.

Dismantling water storage tank exc 500 ltrs & n.exc. 1000 ltrs all as directed by Engineer-in-Charge.

M&L Rotational moulded polyethylene water storage tanks of 1000 ltr capacity (cylinderical verticla with closed top) three layered hoised and fixed in position all as specified in SSR part I all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connecting including cleaning for refixing or removal to stores for 20mm bore complete all as specified and directed by Engineer-in-Charge.

Refixing 20mm dia old steel water tubing and connecting in new or old position with S&F all fitting complete all as specified and directed by Engineer-in-Charge.

M&L GI tubes medium grade 20mm bore fixed complete to wall or laid in floor. complete all as specified and as directed.

Taking up or down steel water tubing and connecting including cleaning for refixing or removal to stores for 15mm bore all as directed by Engineer-in-Charge.

S & F GI tubing 15 mm bore medium grade with all fittings & fixed complete to walls or laid in floors all as specified and directed by Engineer-in-Charge.

Refixing 15mm dia old steel water tubing and connecting in new or old position with S&F all fitting complete all as specified and directed by Engineer-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick/stone wall all as directed by Engineer-in-Charge.

S & F in repairs ball brass valves with brass rod, high pressure with polythelene float and fly nut complete, screwed for iron pipe or for brass ferrule of 20mm dia all as specified and as directed.

S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head screwed both ends for Iron pipe and fixed all as specified and as directed.

S & F in repairs 15 mm bore fancy type chromium plated pillar taps cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

S & F in repairs stop cocks 15 mm bore, chromium plated , fancy type screwed down , high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

S & F in repairs wash hand basins, vitreous china( flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including waste coupling fitting, brass chromium plated 32 mm size with long screwed shucks and fly nuts and including PVC discharge pipe all as specified and as directed.

S & F in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440 mm white with `P' or `S' trap, front or back inlet and integral foot rests including connection to trap, to flushing pipe etc. complete including PCC for making good to floor etc. all as specified and as directed.

S & F in repairs 10 litres PVC valveless syphonic action type flushing cistern high/low level, white complete with inlet, ball valve, float and handle including brackets and telescopic down pipes and joint with WC complete all as specified and as directed.

S & F PVC connection 15 mm bore size with PTMT nuts and PVC washers of length 450 mm all as directed.

S & F in repairs urinal of size 345 x 355 x 535 mm,alongwith Water sprinckler (push type)and with fixing accessories (Make- Jaguar Model No. URS-WHT-13261) all as specified and as directed by Engineer-in-Charge.

S & F under counter top wash hand basin, white of size 450mm X 580 mm X165mm (Make -Jaguar Model No. FLS-WHT-5933) or equivalent including waste coupling fitting, brass chromium plated 32 mm size with long screwed shucks and fly nuts and including PVC discharge pipe as specified and as directed.

S & F in repairs single piece WC with UF seat cover , hinges, fixing accessories set, cistern fittings of size 655 X 365 X 755 mm with P trap-180mm Make- Jaguar Model No. LYS-WHT-38851P, or equivalent all as specified and directed by Engr-in-Charge.

S & F in repairs 15mm bore bib cock (straight line model) with wall flange Make Jaguar Model No. LYR-38053 or equivalent all as specified and directed by Engr-in-Charge.

S & F in repairs 15mm bore Angular stop cock with wall flange Make Jaguar Model No. LYR-38083K or equivalent all as specified and directed by Engr-in-Charge.

S & F exposed part kit of concealed stop cock 15mm bore with fitting sleeve, operating lever & adjustable wall flange with seal Make Jaguar, or equivalent all as specified and directed by Engr-in-Charge.

S & F paper holder with flap recessed type(stainless steel) (Make -Jaguar,)or equivalent all as directed.

S & F soap dish recessed type(stainless steel) (Make -Jaguar, )or equivalent all as directed.

S & F towel rack 60 cm long with lower hanger (stainless steel) (Make -Jaguar,)or equivalent all as specified and directed.

S & F 10-12mm thick frosted toughened glass door(logo of Air Force as specified and directed) with two nos of stainless steel handles for each shutter, 250mm long of decorative quality, floor spring of heavy duty in each shutter alongwith all fitting and fixtures and locking arrangements of approved make all as specified and directed by Engr-in-Charge.

S & F Stainless steel of superior quality (circular, rectangular or Square pipe) railing designer type alongwith all fittings & fixtures all as specified and directed by Engr-in-Charge and approved by GE.

Removing and re-fixing of old serviceable electricals fittings of any description from wall, ceiling etc and fixing it in serviceable working condition after the completion of bldg works all as specified and directed by Engineer-in-Charge.

S & F PVC (SWR) floor trap of 100 mm outlet plain with grating including jointing with solvent cement all as directed.

S & F 40 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/ Sq. Cm., fixed complete to walls, ceilings or in floors etc. all as directed.

Taking down eaves gutter/ rainwater pipes (any size of pattern), including all fittings, heads, shoes, bends, swan-necks etc including cleaning or refixing or removal to store all as specified and directed.

S & F PVC (SWR) pipes, single socketed, in any length, with rubber rings 110 mm dia as in floor/wall all as directed.

S & F PVC (SWR) pipes, single socketed, in any length, with rubber rings 75 mm dia as in floor/wall all as directed.

S & F PVC (SWR) floor trap 75mm bore plain with grating including jointing with solvent cement all as directed.

S & F PVC (SWR) floor trap 100 mm bore plain with grating including jointing with solvent cement all as directed.

S & F PVC (SWR) bends 110 mm dia with access door all as directed.

S & F PVC (SWR) bends 75 mm dia with access door all as directed.

S & F PVC (SWR) bends 110 mm dia all as directed.

S & F PVC (SWR) bends 75 mm dia all as directed.

S & F PVC (SWR) vent cowl 110 mm dia all as directed.

S & F PVC (SWR) vent cowl 75 mm dia all as directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc 1.5 Sqm each all as directed.

All as per item No. 74 here-in-before but exc 1.5 sqm but not exc 4 Sqm each all as directed.

S & F powder coated aluminium sections for doors and windows/ventilators/Partition walls etc including frames of size as approved and fixed all as specified and directed (Note : (i) Paneling such as glass , Gauge etc will be measured and paid saparately.(ii) The rate quoted under this item deemed included for necessary jointing cleates, glazing clips, aluminium beading, screws, rubber packing and locking devices & in built handles for sliding windows. However, no element on account of weight will be taken into consideration for these item.(iii) Floor door spring/locks/tower bolts/ handles/ door closure/hinges for doors measured saparately.(iv) Size of door / windows shall be all as directed at site.(v) Grills will be measured saparately.(vi) Second class hard wood batten of appropriate size to be inserted inside the frame for fixing hinges and the same is included in the rate quoted.)

S & F plain sheet glass 5 mm thick tinted, fixed to aluminium doors/ windows / ventilators complete all as directed by Engr-in-Charge (Note:- Beading/rubber packing is included in the rates for aluminium sections above.)

All as per serial item No.77 above but frosted glass.

S&F in repair double action floor door stoper/spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation bore, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in fixed including taking down and refixing aluminium shutter in the same opening all as directed.

S & F in repairs aluminium (die cast) body door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters of 700 mm in width & weight not more than 35 Kg all as directed.

S&F in repair Mortice lock brass 100 mm 4 lever vertical type fixed all as directed.

S & F 200 mm size aluminium powder coated barrel tower bolt of extruded section all as directed.

S&F factory made solid panel PVC door frame of size 50mmx47mm out of 5mm wood grain printed PVC sheet & edges will be printed to match with printed sheet reinforced with M.S. square tube, all as per specification and drawing all as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a laminate PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and single sides prelam PVC sheet and stile & rails having one side feathered edge and on other side 10mm (90°) bent edges & as gap insert for top rail & bottom rail; Panelling to be fitted in the M.S. frame welded/ sealed to the styles & rail with suitable PVC sheet beading, and joint together with solvent cement, all as specification and drawing all as directed.

S & F 125mm long Butt hinges, extruded aluminium powder coated with galvanised mild steel hinge pin anodised and fixed type B-21all as directed.

S & F 100mm long Butt hinges, steelness steel hinge pin anodised and fixed type B-21all as directed.

S & F 200 mm size aluminium anodised barrel tower bolt of extruded section all as directed.

S & F powder coated aluminum handle D type cast type 150mm size all as directed.

S & F in repairs 140mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor all as directed.

Dismantling Structural steel work including doors, gates but excluding framed truss etc. all as directed.

S & F rolled mild steel framed work as in HAND RAILS ,doors or gates of angle or other section confirming to Fe 410 - W, with gusset plates, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including eihter hooks and hinges or steel hnaging door fittings (exclussive of steel sheeting or other covering running rails and guides and hanging also fastening and fixing complete all as specified and directed by Engineer-in-Charge. and hanging and fixing complete.

S & F 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates, etc., cut to size, holes punched including rounded headed screws, clout nails or revets and fixed to wood or steel framing or fixing to MS clamps with necessary bolts and nuts with plain 40mm lap joints welded to frame as directed.

M & L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as directed.

M & L for preparation of old or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

M & L for preparation of old or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

SHREE SAMARTH SERVICES

NIKAASH INFRACON