Conservation, Restoration and Development works at Mahadev Mandir ki Bawdi, Intali (Salumbar), Baiji ki Bawdi - Gogunda (Udaipur) and Chhota Gopalpura Ki Bawdi - Nathdwara (Rajsamand)

Carriage of Materials: uilding Rubbish Stone metal (Grit and ballast etc.) For 10 Km.

Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 : Upto 15 cm. thick.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: In lime mortar.

Earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 Sqm on plan including disposal of excavated earth up to 50 Mtr. and lift up to 1.5 Mtr. disposed soil to be levelled and neatly dressed : All kinds of soil

Supply and fixing Jodhpur sand stone Machine cut Kerb stone (10cm wide 40 cm. height) fixed in white cement sand mortar 1:4 with pigment including Earth work.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead.

Fine grinded Gangsaw cut 30-35 mm thick stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement :4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI.Mandana stone

Providing and fixing double scaffolding system on the exterior side, upto five story made with 4" wooden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. The scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of EI.The lavation area of the scaffolding shall be measured for payment. The payment will be made once irrespective of duration of scaffolding. Note : This item to be used for maintence work judicially

Providing and fixing Stone jali 50mm thick Red/Pink sand stone as per ornamental design to fixed with white cement/epoxy mortar including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade.

Supplying and fixing machine cut dressed 75 mm Pink sand stone (Bansi Paharpur) dasa/ coping wth ornamental shape having moulding and "PAN Shape" engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade.

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :25 mm thick

Extra for plastering done on moulding cornices or architraves including neat finish to line and level: In two coats

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats)

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work

Fine dressed & machine cut edges 30-35 mm thicksand stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI. Mandana stone

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

Extra if square,rectangular hollow tubelar sections are used or grill made by flats only

Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. Expended metal size 20-25 mm size 18SWG

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

BoQ_Ver3.0

NIB No: 11/ 2025-26

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE PART-B (BASED ON A&M BSR-2011) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Providing and fixing fine dressed sand stone "Todies" (Brackets) as per existing matching stone with moulding work with fine finishing , fixing in grinded lime surkhi mortar 1:2 including scaffolding, lead & lift complete in all respect.(d) Size : 150cm X 60cm X 10cm (exposed part only.)

Refixing of existing "Ashlar stone work "(Plain work) of templeby machenical/manual system carefully with proper order and sequence, fixing with grinded lime surkhi/ sand mortar 1:2 and joints flush with lime cream and stoned ust1:1 including all scaffolding and shuttering work, the place as directed by Engineer incharge.

Removing/ dismambering of disturbed "Ashlar stonework" (plain work) of temple bymachenical/manual systemcarefullywith proper marking and complete dcumentation including all scaffolding and shutteringwork,stackingtheuseful partsinpropersequenceat theplace as directed by Engineer incharge.

Scraping & Removing of white wash/ distemper/ oil paint/ algli etc. from plain plaster & surfaces gently with care to keep intact the old designs.

Providing and fixing fine dressed sand stone "Dasa/coping" as per existing matching , fixing in grinded lime surkhi mortar 1:2 including pointing in cream and stone powder 1:1 with an admixture of pigment to match the shade of stone complete in all respect. (d) above 100mm to 150mm thick with pan patti design.

Providing and fixing stone Patties (slab) on roofing including removing broken patties carefully and replacement new slab with Kharanja, ralthal and lime dhar as per traditional practice. Span about 3.30 mtr. To 5.50 mtr. 100 mm to 150mm thick of approved stone.

Lime Surkhi Plaster 1:2 (1Lime: 2Surkhi) including preparation of mortar by traditional practice (by grinding) in 3 course for base coarse and subsequent course & Loi, tamping, beating, curring till the shrinkage cracks are disappear. The work is to be done with all lead as the work is of restoration nature as per Jaipur practice including adding gur, methi & gugal on old walls including removal of all old loose and decade plaster, each coat to be done after 3 days of previous coat. 45 mm thick in four coats

Tuman masonry by brick bats/ stones in grinded mortar of Lime Surkhi mortar 1:2/lime sand mortar 1:2 including racking and removal of all old loose plaster and cleaning the wall surface properly as per direction of Engineer Incharge.

Add extra for decorative/ornamental Lime surkhi 1:2 plaster work with fine finish making kangoora, flowers, geometrical designs upto (khat) including preparation of Lime surkhi mortar 1:2 as per tradititional practice adding gur,methi,gugal etc. Upto 25mm thick/depth

Add extra over item no. 3.1 to 3.3.3 for Lime plaster work done over curved/circular masonary work (curved or circular surface.)

Add extra over item no. 3.1 to 3.3.3 for Lime plaster work done over Spherical or groin ceiling/ladao ceiling of doms.

Providing & applying Lime kara 1:2 (1lime cream : 2 Zikki powder) grinding mortar with grinding mill/manually on lime base,on all flat surface in two coats.First coat applying 3mm to 4mm thick and curing properly at least 7 days,second finishing coat done after 7days of previous coat as per traditional practice.(thickness not more than 6 mm.)

Providing & applying Lime kara 1:2 (1lime cream : 2 Zikki powder) grinding mortar with grinding mill/manually (on lime surkhi/sand plaster base) on decorative/ornamental lime plaster in two coats.First coat applying 3mm to 4mm thick and curing properly at least 7 days,second finishing coat done after 7days of previous coat as per traditional practice.(thickness not more than 6 mm.)

(a) curved surface.

(b) domical surface/spherical/domical ceiling.

Khamira Colour Washing as per old traditional practice to prepare the Khamira the lime should be slaked atleast for 7-10 days and regularly it should be stirred by adding cured, Gugal, for non-synthetic colour adding gum (babool gum) as per specification. Then applying prepared solution on walls three to four thin coats as desired finishing.

Crack filling in masonary walls with grinded masaldar lime surkhi mortar 1:2 (adding gur, gugal, methi, belgiri) including cleaning the crack properly complete in all respect Crack thickness above 25mm and upto 50mm (average)

Chemical treatment of sand stone to clean from yellowness, blackness, algal growth, dust, dirt oily accretions, lime & gypsum deposits, filling of cracks/ joining of gaps/ pointing, strengthening of weak stone, removal of salt effect and application of preservative coating to prevent algal growth and make the stone water proof.

Providing and fixing of fine dressed stone "Steps" (solid) of temple withmatching stone/ approved quarry fixing of steps as per temple architecture by machanical/ mannual system carefully in prope rorder and sequence including all lead & lift as per direction of Engineer incharge.

De-vegetation from monument by removing bushes, trees including complete up rooting from the wall & roofs/ structures carefully including sutaible chemical treatment to roots to avoid further growth including disposal of rubbish within 50mtr. Lead as per direction of Engineer in charge.

Site clearance by uprooting of trunk vegetation, bush, wood, trees and sapplings of girth upto 15 cm sand disposal of rubbish within 50 mtr. Including leveling and dressing of ground as per direction of Engineer incharge.

Removal of debries from the monument carefully without damaging the buried architectural parts of the monument and collect all the intact parts at proper place for reuse at the time of restoration work as per direction of Engineer incharge/site encharge and disposal of building rubbish with in 50mtr.lead.

Add extra for sorting lifting & stacking charges for architectural parts with in 50mtr.lead (Labour charge.)

Providing and fixing fine dressed sand stone "Dasa/coping" as per existing matching , fixing in grinded lime surkhi mortar 1:2 including pointing in cream and stone powder 1:1 with an admixture of pigment to match the shade of stone complete in all respect. (b) above 100mm to 150mm thick plain with fine dressing.

Providing and Fixing fine dressed sand stone /approved stone "Chajja" for palaces,chattries,forts and jharokas with fine dressed surface both sides and front edges should be round shape/moulding, fixing in grinded lime surkhi mortar 1:2 joint flush with proper adhesive with pigment to match the shade of stone (thickness of chajja on front edge 50mm and 75mm on fixing end) exposed surface is to be measured only.

Making Gardana under ceiling/ chajja with katla stone and grinded Lime surkhi mortar 1:2 including moulding work and fine finishing with grinded Lime surkhi mortar 1:2 as

per existing matching/ traditional practice completev in all respect;. Size 25cm X 25cm.

Making Bend -patta, Cornice, Gola & String course with katla stone and Lime surkhi mortar 1:2 (projected ) and finishing with grinded Lime surkhi mortar 1:2 including moulding/ design work as per existing matching at site complete in all respect.Size 20cm X 10cm.

Coloured plain Araish work 1:2 (1 lime : 2 zikki) on lime plaster or plane back ground including preparation of lime for 6 months by slaking of lime with curd and changing the water every week. The Kara plaster of not more than 6mm thick is to be left the maximum of 3 months to appear the shrinkage & temperature cracks. Over the Kara plaster 2mm layer of grinded lime putty is to be done and is to be rubbed Gently by Akik stone. Then adding Khoppra & Ghee and inserting the design of colour boarder all round including desired colour stone pigment to match the existing colour.

Steel-rod stitching incracked stone patties, beam,and lintels.Providing and fixing stainless steel rods of 90cms length of which 15cm on either side and cold bending at 90degrees. The stainless steel clamps to be fixed perpendicular to the crack by drilling in stone and fixing with cement and aradite mixture in such a way that the entire length of the rod is in complete contact of the stone and the bent ends are fully inserted in the cracked stone. Use 316 grade stainless steel charge per hole.steel rod charges are counted per kg.Holes with 6mm, 8mm, 10mm or 12mm dia.as per requirement of position.

Providing and fixing double leaf Window wooden shutters made of Ist grade wood as per trditional design (Deshi pattern) planks thickness 25mm and width of Binies, Andheri 35mm and 25mm, including Adwa etc. with fittings (nails, sankal, kunda, cheri, handle and patti etc.) as per existing matching/ as per approved design with moulding/ carving complete in all respect : Sheesham wood grade Ist.. M.P teak wood grade Ist

Providing and Fixing fine dressed sand stone approved stone" Railing" as per existing design and matching with thambli,fixing of railing with proper adhesive /clips complete in all respect (thambli & clips paid seperately.) (b) 75 mm. thick with moulding/lining.

Providing and Fixing fine dressed sand stone /approved stone "Thambli" (katahara pillers including) kalash on top,fixing on dasa as per existing design for fixing of stone jalies/railings including making grooves as per required size.(b) Size 150x150x750mm including kalash with moulding.

Flush pointing over joints of dressed stone cladding, chajjas, jali etc. with neat cement, sand & colour including racking the joints as per Jodhpur practice including all leads and lifts with grinded mortar of lime putty and stone powder mixed in 1:1 ratio and gur, methi, gugal etc. are to be mixed as per old traditional practice.

Providing & fixing fine dressed machine cut sand stone Stone steps (Treads & risers) with round nising as per existing matching fixing in lime surkhi mortar 1:2 including pointing in lime cream and stone dust 1:1 with an admixture (50mm to 60mm thick)

Providing & fixing ashlar "Rain water Spouts" (3) lines dressed as per traditional practice / existing design / approved design size 60 x 30 x 25 cm, fixing the rain water spout with lime surkhi mortar 1:2, with proper slope complete in all respect.

BoQ_Ver3.0

NIB No: 11/ 2025-26

Name of the Bidder/ Bidding Firm / Company :

NUMBER #

PRICE SCHEDULE PART-C (ELECTRICAL WORKS BASED ON PWD BSR-2022/2019) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

Supply, installation, Testing and Commissioning of IP-65/ROHS/CE compliant Integrated Solar Street Light fixture having die cast Aluminium body CNCASCS with integrated monocrystaline solar PV panel with lithiumILiFePO4) ferro Phosphate battery and comPliant to MNRE specifications / BIS approved .luminaire should be with secondary optic lenses for better distribution with delivered efficacy of > L00 Lumens per Watt,with minimum 40000 hrs. rated LamP Iife with LED's brand of Philips/Osram/Nichia/CreelSeoul and driver eficiency should be >B5o/o , CRI > 75,CCT 6000 to 6500d K Microcontroller based high efficiency controller cum driver designed with automatic dimming function with PIR motion sensor ( full power lighting when a human move in the sensor range and only 300/o lighting when a human move out ) , Dusk to Down operation, working temperature t-l LOoC to [*) 55oC, with adjustable clamp suitable for pole/wall mounting complete in all respect with protection like short circuit, overload, reverse polarity and battery protections. Light coverage must be LZ} Degree or greater complete as required. Compact Solar LED Street Light-60 Wp[mono)1,8v /12.8V 24 AH/30 W

Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sections designed to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheet steel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4 no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. Poles with Octagonal Cross Section. 3 Mtr.

BoQ_Ver3.0

NIB No: 11/ 2025-26

Name of the Bidder/ Bidding Firm / Company :

Providing and Laying RCC Foundation for Octagonal / Conical Street Light poles, High mast Poles as per Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. A) Excavation of Pit for Foundation Size upto required depth from Ground level. B) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete. C) Providing and laying in position cement concrete of M-10 grade of 75 mm thickness. D) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing in position and binding all complete. E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing and Pedestal. F) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations. G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal including Curing the foundation for 7 days. H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face.

NUMBER #

PRICE SCHEDULE PART-D (NON BSR ITEMS) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

Silt and Sludge clearance of the entire Kund with sewage pumps or with labour/sweepers etc. to clean all the water sources below and o

n the sides of the Kund complete and disposal of the sludge including all leads and lift to some remote dumping ground, location of such dumping ground will be the responsibility of the Contractor and he had to comply with all statutory requirements.

Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.

Providing and Constructing Random rubble masonry walls by using existing matching stone for old forts/Palaces at all heights above plinth level and more than 30 cm thick walls in grinded mortar of Lime Sand Surkhi mortar 1:1:1 and mixing gur, gugal, methi,bel rus and any other additives as per specification @4.00kg each as directed by the Architect, including racking and removal of all old loose plaster and cleaning the wall surface properly with all scaffoldings,lift & lead as per direction of Engineer Incharge.

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 3 metre long and size 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing including all material, labour. 60 cm x 45 cm rectangular

Providing,carving and Fixing of interpretive signages in Bansi paharpur stone of size 1000x1300x50 mm on inclined plane .Engraving,painting of latters as per drawing and design.The signage stone shall be fixed on the post of same stone of size 300x 300 x 1050 above ground and 1/3 of total heigt of post shall be embedded in ground with neccesary earthwork and concreting etc.complete as per details and drawings and as directed by engineer incharge.

Sandstone Column/Arch/Lintal: Providing new decorative sandstone columns /arches/lintals per the original details found on site. The damaged portions of the original columns /arches/lintals/Elements to be carefully dismantled without damaging the adjacent areas, & replacing the same with new detail of the same size & design. Sample of the terra cotta columns /arches/lintals to be shown to the Engineer in charge for approvals before procuring & fixing the same on site. Item to include all necessary anchoring details, scaffolding if required etc. complete. Mode of Measurement: Item to be paid each restored/new column.for using plain

Add Extra for additional lift beyond 1.5 mtr. & upto 50 mtr. For all type of material for Baori work through manual means, including loading, unloading & necessary requirement.

Providing & fixing "ornamental stone cladding" of approved sand stone with dressing complete as per existing design/pattern/approved design, fixing with 20mm thickgrinded Cement sand Mortar 1:3 (1 cement: 3 sand) & pointing with white cement with araldite and pigment to match shade the stone complete in all respect as per direction of Engineer

Tour Taxi (I.e. Sedan type four wheeler & four seater) Jaipur to site and return including toll tax, driver expenses( food, night stay misc. including GST and other taxes and charges.