PROVN OF MECHANICAL LAUNDRY WITH WASHING MACHINE, DRIERS, HYDRO EXTRACTORS, CALENDARING AND PRESSING IN MH JHANSI

Amount

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc complete all as specified and directed.

Taking Down chowkhat or frame with shutter (without taking of shutter from frame) area n.exc 1.50 sqm complete all as specified and directed.

Taking down chowkhat or frame exc 1.5 sqm but not exc 4.00 sqm with shutter (without taking off shutter from frame) complete all as specified and directed.

Demolition of cement concrete (reinforced) in Roofs floors (other than ground floor)beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not bcking) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 with water proofing compound finished fair and even without using extra cement complete all as specified and as directed. Note: water proofing compound shall be measured seprately.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished fair and smooth without using extra cement complete all as specified and as directed.

Preparing newly plastered surfaces of new wall and applying two coats of weather coat paint over and including a coat of primer complete all as sppecified and directed.

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over a coat of primerr complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of oil bound distember over a coat of primer including complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old surfaces of wall and applying two coats of emulsion exterior coat( weather proof) over and including a coat of primer complete all as specified and directed.

Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and over applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide complete all as specified and directed.

ditto as per item No 14 as above but applying one coat of synthetic enamel paint on old wooden surface including preparation complete all as specified and directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for brick work with flyash bricks,old size straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L for brick work with fly ash bricks old size , straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid to slope 1:30 including forming joints not more than 2 mtr in length and corners of 10 mm wide and upto full depth of PCC and filled with bitumen mastic (1:3) 1 part bitumen 85/25 and 3 parts of sand complete all as specified and directed. Note:-Rate is deemed to be inclusive of materials against forming & filling of joints.

M&L for Jointless Non - skid Ceramic tiles 7 tob8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.complete all as specified and directed

M&L for glazed ceramic coloured tiles in vertical surface 450 X350X 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles inclduing 10mm thick rough plaster layer as in backing coat in CM 1: 4 complete all as specified and directed.

S&F Box type steel windows with 80x40x1.25mm CRCA sheet frame with side hung shutters (double shutters for glass and gauze) with out sash bars jointed together with and including grills using 12mm square bars @ 10cm C/C as per TD No CEBZ/TD/14/ 2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and as directed by the Engineer-in-Charge Note:-Rate for glass and gauge (wire mesh) are not included in the same item and the same shall be measured and paid separatly.

S&F for 3mm thick sheet glass ordinary quality glazing with oil putty or wooden beads in square n exc 0.5 Sqm in each pane complete all as specified and directed.

S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel hold fast and similar small articles conforming to Fe-290 Gde-165, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) for bed block for fixing of chowkhats,coping etc complete all as specified and directed.

S&F stainless steel curtain rod 25mm dia with caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed.

M & L for Reinforce cement concrete , type B1,1:2:4 (Nominal Mix) using 20mm graded aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar work complete all as specified and directed.

S/F MS TMT bars 10 mm dia & over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Ditto-but 5 mm dia and over upto and including 10 mm dia in stirrups, spacer and binders complete all as specified and directed.

Form work to soffits of suspended slabs such as floor slab, roof slab ,landing slab and similar work n exc 200mm thick including edges complete for rough finished surface all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses ,Staging for Tank or Sliding gate with frame with neccessary bearing (framed), purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S&F powder coated/anodised aluminium frame for door, windows, ventulators with one or more rebates including joining cleat for fixing etc complete all as specified.make Jindal (Section No 4614 for door and Section No 4619 for window & ventulator) complete all as specified and directed.

S&F powder coated/anodised aluminium door shutter weighing 0.55 kg/m including necessary jointing cleat,glazing clips, rubber neoprene packing , handle 2 Nos in each doors, hinges anodised aluminium snap beading with one or more rebates including screws etc complete all as specified and directed.

S&F 12 mm thick prelaminated particle board, exterior grade prelaminated both sides with decorative choice laminations complete all as specified and directed.

M & L for 6.3 mm thick sheet glass, ordinary quality and 50micron solar control film fixed on glass joining cleats, glazing clipsy in square exc. 0.50 sqm in each pane complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc, and getting out in any type of soil complete all as specified and directed.

M & L for cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) as in saucer drain/surface channel complete all as specified and directed.

Returning, filling in trenches including spreading , leveling, watering in layers n.exc 25cm thick soft loose soil complete all as specified and directed.

Removal of excavated soil n.exc 50mtr distance and depositing where directed n.exc 1.5m above the starting point complete all as specified and directed.

Extra for forming fair finished surfaces of drain or channels, inner girth n. exc 30 cms, using extra cement including forms, moulds mitred/ stoppedends etc., complete all as specified and directed.

Provn of Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4 M dia X 3.0 M effective depth (Refer TD No CEBZ/TD/78/ 2011 Sheet No 1/2 and 2/2) complete all as specified and directed.

M&L for Precast cement concrete type B-1, 1:2:4 (Nominal mix) using 12.5 mm grade crushed stone aggregate, as in cover slabs,saucer drain etc with ms steel frame work all around casted at site and setting in cement mortar 1:4 complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

S&F 15mm medium grade GI steel tubing including all fittings and fixed complete to wall ,ceiling and laid in floor etc complete all as specified and directed.

S&F rotational moulded polythylene water storage tanks 2000 liitre of capacity (cylindrical vertical with closed tap) and fixed in position all as specified in SSR Part-I complete all as specified and directed. Make : Sintex, Polycon, Rotax

S&F 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S & F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. Make : Leader, Kirloskar, Zoloto

Supply only integral liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed. Make : Dr Fixit LW + Professional or equivalent of Fosroc / Pidilite

Supply, installation, testing & commissioning of Washer Extractor, high spin, soft mount, of capacity not less than 30 kg, electric heated, front loading, open pocket, stainless steel cabinet, microprocessor controlled complete with the following detailed specifications and all as directed:- (i) Capacity : not less than 30kg dry weight of 100% cottons per charge. (ii) Outer Cabinet: Stainless steel 304 quality front, sides, top & back covers.S.S. front door interlocked with drive. (iii) Outer Drum: Stainless steel of 304 quality duly reinforced to support front door, bearing housing, springs, electric motor & shock absorbers. (iv) Inner Cylinder: Stainless steel of 304 quality, dimpled perforations, coned S.S. back-end-plate with tapered S.S. bush at the center, push fit main shaft, easy to dismantle.(Carbon Steel shall not be used anywhere on the cylinder.) (v) Bearing Housing: Cast Iron one piece bearing housing with extra wide roller & ball bearings packed with lubricants & sealed. Self lubricating seals for water tightness & for lubricant tightness of bearings. (vi) Drive: Single motor of suitable rating with Variable Frequency Drive for various speeds for wash, distribution, low, normal & high spin extract. (vii) Computer: Fully programmable microprocessor with at least 30 customized or preset processes with step by step LCD instructions for cycle advance, variable time signal, process modification & diagnostic checks. (viii) Soap Dispenser: 5 compartment in-built soap dispenser for powder & liquid detergents, each fitted with independent water solenoid valve & pressure jet. (ix) Suspension : Coil springs & hydraulic shock absorbers. (x) Water Inlet: Ø 25 mm (0.75” BSP) Solenoid valve operated. (xi) Drain: Ø 65 mm (2.5” BSP) Motorized, non clog Drain Valve. (xii) Power Supply: 415V ±5%, 3Phase, 50 Hz, AC.

Supply, installation, testing & commissioning of Drying Tumbler, of capacity not less than 30 kg, electric heated, stainless steel cylinder, microprocessor control, reversible with cool down feature complete with the following detailed specifications and all as directed:- (i) Capacity: not less than 30kg dry weight of 100% cottons per charge. (ii) Outer Cabinet: Double walled for heat insulation, hot painted, front & back service only. Can be joined together for multiple installation. (iii) Inner Cylinder: Stainless steel 304 grade perforated inner cylinder, back end plate reinforced with M.S. Channel/Trunion. (iv) Electric Controls: Microprocessor control for drying & cool-down time, auto digital temperature control with moisture control & humidity sensor. (v) Drive: Main & idler drive through 'V' belts & pulleys running on self aligning ball bearings encased in plummer blocks. (vi) Suction Blower: Aluminum cast suction blower driven by independent blower motor for optimized air flow. (vii) Electric Radiator: Formed out of stainless steel heating elements with galvanized rectangular fins. (viii) Power Supply: 415V ±5%, 3-Phase + N, 50 Hz AC

Supply, installation, testing & commissioning of Flat Work Drying Ironer, chest heated, having roller & chest size Ø380mm x 2000 mm length, electric heated, front feed, front return complete with the following detailed specifications and all as directed:- (i) Roller: Made of steel, precision machined with perforations throughout its length & periphery for moisture suction. Runs on self aligning ball bearings. Padded with galvanized springs & double layer polyester padding. (ii) Ironing Chest: Sliding type. Precision machined, ground smooth and polished chest moves back & forth through pneumatic cylinders at both sides. Perfect contact with the roller. Adjustable & uniform ironing pressure across the entire roll. Chest should move back automatically at the time of power failure or when the machine is stopped. (iii) Main Body: Made of steel, hot painted, Full length conveyor feed belts. Full length, underneath linen collection tray. (iv) Drive: Single Motor of suitable rating working in conjunction with variable frequency drive. Roller is driven by an electric motor coupled with a reduction gear box unit which is lubricant packed & sealed. The final transmission is through sprockets & chain. Easy chain tensioning device. (v) Controls: Push buttons to start & stop the machine. Auto digital temperature control. Rocker switch for forward-reverse chest rotation. Emergency stop push button. (vi) Moisture Suction Blower: Directly Mounted on to the hollowed suction side shaft of the roller. (vii) Padding: Galvanized coil type or leaf type springs covered with heat resistant double layer polyester padding of minimum 900GSM quality. (viii) Air Connection: Ø 15 mm (0.5” BSP), with Filter Lubricator & Pressure Regulator. (ix) Finger Safety Guard: Auto cut off by Swing Guard for false feeding & finger safety. (x) Roller Speed: 2 to 6 meters per minute (Variable). (xi) Conveyor Roller & Feed Belts: Steel rubberized conveyor roller runs in self aligning ball bearings & driven by chain & sprocket. Polyester Feed Belts of welded seams joined with stainless steel comb hooks. Easily replaceable with belt tightening device. (xii) Electric Supply: 415V ±5%, 3Phase, 50 Hz, AC.

Supply, installation, testing & commissioning of Vacuum Finishing Table, rectangular table top of size 1200mm x 750 mm, centrifugal suction, extended exhaust duct with rack & concealed lighting device complete with the following detailed specifications and all as directed:- (i) Main Body: Metallic, hot painted. All components to be easily accessible. (ii) Table Top: Densely perforated aluminum plate padded with high porosity & heat resistant silicon padding & polyester cover. (iii) Suction Blower: Heavy duty centrifugal blower driven by independent blower motor activated by spring loaded full length foot pedal. (iv) Exhaust: Extended exhaust duct with full length rack & concealed lighting device. (v) Table Heater: 1KW thermostatically controlled stainless steel tubular heater fitted below the aluminum table top to keep the padding dry at all times. (vi) Electric Supply: 415V ±5%, 3Phase, 50 Hz, AC

Supply, installation, testing & commissioning of Steam Generator of capacity not less than 8 kg per hour, electric, portable, fully automatic with pump, stainless steel pressure vessel, automatic steam release safety plug, audio signal for low water level, steam solenoid valve with flow control knob, built in water storage tank complete with the following detailed specifications and all as directed:- (i) Steam Pressure: 8 Kg /cm² (min) (ii) Pressure Vessel : Not less than 12 liters capacity. (iii) Water Feed Pump : 700 Watts. (iv) Water Level Controller: Float type with stainless steel float ball. (v) Pressure Control Switch: Diaphragm type with pressure differential of 0.5 Kg. (vi) Electric Heating Load: Not less than 4KW (vii) Water Storage Tank : Not less the 25 Liters (viii) Power Supply: 415V ±5%, 3Phase, 50 Hz, AC.

Supply, installation, testing & commissioning of Air Compressor, 1 HP, reciprocating type, single stage, single cylinder, 'V' belt driven, continuous duty, tank Capacity 45 Liters, free air delivery 200 Liters/minute, working Pressure 8kg/cm² complete with suitable motor, starter, pressure switch, pressure gauge, 'V' belt & belt guard etc complete all as specified and as directed.

M&L for Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of pressed steel terminal box with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass / GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points:-

One light / exhaust fan / ceiling fan/ bell point controlled by one switch complete all as specified and directed.

One 6A socket point controlled by one switch on independent board complete all as specified and directed.

One 6A socket point controlled by one switch on same board complete all as specified and directed.

All as per srl item no. 57 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.

M&L for sub main wiring with 4runs x 6 sqmm(3Ph & N) + 1run x 6 sqmm(earth wire) with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Five runs of copper cable and one run of PVC conduit shall be measured as one unit length.

Notes for item No. 57.00 to 59.00: (i) Quoted rate shall deemed to include the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & capping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing capping may be used in that portion.

Supply and fix switch piano flush type 6 Amps, one way, 240V, 50Hz complete all as specified and directed.

Supply and fix socket 6 Amps, 2-in-1, 5 pin flush type universal 240V, 50Hz complete all as specified and directed.

Supply and fix switch piano flush type 16 Amps, one way, 240V, 50Hz complete all as specified and directed.

Supply and fix socket 16A & 6A, 2-in-1 flush type universal 240V, 50Hz complete all as specified and directed.

Supply and fix Lamp holder, angle type with metal ring, PVC/Polycarbonate body complete all as specified and directed.

Supply and fix ceiling rose 6 Amps, 3 plate, 240V, 50Hz complete all as specified and directed.

Supply and fix electronic fan regulator rotary type in 5 steps (0 to 5), 2 module size, 240V, 50Hz complete all as specified and directed.

Supply and fix 7 W LED lamp, retrofit type suitable for B-22 holder base with polycarbonate diffuser complete all as specified and directed.

Supply and fix LED batten with CRCA sheet steel box type body pre-wired suitable for and including provision of 1x20/22 Watt (4 feet) retrofit LED tube with PC body, full white and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED street/security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable of size 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and as directed.

Supply and fix exhaust fan, 300mm sweep with 04 Nos of blade leafs, 70 W power consumption, 1300 to1400 RPM, 100 % copper winding heavy duty motor with double ball bearings including supply and fixing of metallic louvers and connecting up with 3 core x 0.5 sqmm flexible copper conductor cable from ceiling rose to connector of fan complete all as specified and directed.

Supply and fix MCCB / MCB distribution board, Vertical TPN, 12 way with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 4 way in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix MCCB, 100 A, 16 KA, 4 Pole with thermal magnetic release, AC, 415 Volts, 50 Hz complete all as specified and directed.

Supply and fix MCB 25 - 63A, 10 KA, TP, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply and fix MCB 6 - 32A, 10 KA, single Pole, 'C' curve, 240 V, 50 Hz complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 35 sq. mm nominal cross section, 3.5 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure pipe, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

M&L for cutting of existing road / hard standing up to 15 cm depth for laying of cables / pipe and making good the disturbed surfaces by providing PCC 1:2:4 after laying of pipes and returning filling of soil, complete all as specified and directed. Note:- Excavation and earth work below road / hard standing will be measured and paid under relevant items.

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Cutting existing steel tubing of size 40mm or 50mm bore and screwing for alterations or additions done in position without taking down and inserting Tee for taking branch connection complete all as specified and directed.

Material and labour for GI pipe 40 mm dia medium grade with all fittings such as socket, union, tee, reducer, elbow, bend, nipple etc laid in trenches / fixed on walls complete all as specified and directed.

Material and labour for GI pipe 25 mm dia medium grade with all fittings such as socket, union, tee, reducer, elbow, bend, nipple etc laid in trenches / fixed on walls complete all as specified and directed.

Supply and fix Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe of size 25mm bore complete all as specified and directed.

RUCHIKA ENGG.WORKS

M/s. Lakhbir constructions