REPAIR MAINTENANCE OF MOTORS AND PUMP SETS SUPPLY INSTALLATIONS AND REPAIR MAINTENANCE OF CHLORONOME PLANTS AND OTHER EM WORKS AT WATER SUPPLY INSTALLATIONS AT AF STATION SURATGARH

Amount

BOQ (REPAIR/MAINT OF PUMPS MOTORS AND CONNECTED ITEMS OF AC PLANTS AT AF STATION SURATGARH)

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 25 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 2 here-in-after and repair of parts as per item No 3 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.1 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing 6312.Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 01 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 35/40 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 5 here-in-after and repair of parts as per item No 6 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.4 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 04 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 75 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 8 here-in-after and repair of parts as per item No 9 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 7 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 04 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 20 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 11 here-in-after and repair of parts as per item No 12 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 10 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 10 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 7.5/10 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 14 here-in-after and repair of parts as per item No 15 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 13 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 13 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 3/5 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 17 here-in-after and repair of parts as per item No 18 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No. 16 here-in-before, complete all as specificed directed by Engineer-in-Charge.

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Repair to parts of pump reqired under item No 16 here-in-above:-

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nuts, bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting & dismantling the defective three phase induction motor squirrel cage of any make and of capacity upto 3 HP 415 Volts, 50 Hz, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed Enginer-in-charge. Note:- (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

All as per srl item No 19 here-in-before but motor of capacity 5 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 7.5 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 10 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 20 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 25 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 30 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 35 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 40 HP complete all as specified and directed Enginer-in-charge.

All as per srl item No 19 here-in-before but motor of capacity 75 HP complete all as specified and directed Enginer-in-charge.

Dismantling/taking out defective submersible pump set of capacity 15 HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well including replacement of parts as per Item No 31 here-in-after and repair of parts as per item No 32 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge.

Rewinding of defective submersible motor of 15 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional, complete all as specificed and directed by Engineer-in-Charge.

Supply only spare parts as under required in Srl item No 29 here-in-before , complete all as specificed and directed by Engineer-in-Charge.

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

Repair to Parts of Submersible pump set required under item No 29 here-in-above:-

Straightening of pump shaft by re-meting welding and grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush fixing.

Dismantling/taking out defective submersible pump set of capacity 10 HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well including replacement of parts as per Item No 35 here-in-after and repair of parts as per item No 36 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge.

Rewinding of defective submersible motor of 10 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional, complete all as specificed and directed by Engineer-in-Charge.

Supply only spare parts as under required in Srl item No 33 here-in-before , complete all as specificed and directed by Engineer-in-Charge.

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

Repair to Parts of Submersible pump set required under item No 33 here-in-above:-

Straightening of pump shaft by re-meting welding and grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush fixing.

Dismantling/taking out defective submersible pump set of capacity 7.5 HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well including replacement of parts as per Item No 39 here-in-after and repair of parts as per item No 40 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge.

Rewinding of defective submersible motor of 7.5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional, complete all as specificed and directed by Engineer-in-Charge.

Supply only spare parts as under required in Srl item No 37 here-in-before , complete all as specificed and directed by Engineer-in-Charge.

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

Repair to Parts of Submersible pump set required under item No 37 here-in-above:-

Dismantling/taking out defective submersible pump set of capacity 5 HP from bore well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well including replacement of parts as per Item No 43 here-in-after and repair of parts as per item No 44 here-in-after including installing, commissioning and testing on full load, complete all as specificed directed by Engineer-in-Charge.

Rewinding of defective submersible motor of 5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional, complete all as specificed and directed by Engineer-in-Charge.

Supply only spare parts as under required in Srl item No 41 here-in-before , complete all as specificed and directed by Engineer-in-Charge.

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

Repair to Parts of Submersible pump set required under item No 41 here-in-above:-

Straightening of pump shaft by re-meting welding and grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush fixing.

Taking out sluice valves of size 300/350 mm, refacing, regrinding and refixing of the same place including turning water off or on and draining the system as required complete all as directed by Engineer-in-Charge.

Taking out sluice valves of size 250 mm, refacing, regrinding and refixing of the same place including turning water off or on and draining the system as required complete all as directed by Engineer-in-Charge.

Taking out sluice valves of size 200 mm, refacing, regrinding and refixing of the same place including turning water off or on and draining the system as required complete all as directed by Engineer-in-Charge.

Taking out sluice valves of size 150 mm, refacing, regrinding and refixing of the same place including turning water off or on and draining the system as required complete all as directed by Engineer-in-Charge.

Taking out sluice valves of size 100 mm, refacing, regrinding and refixing of the same place including turning water off or on and draining the system as required complete all as directed by Engineer-in-Charge.

GI column pipe medium grade ISI marked of size 80 mm bore each of three mtrs length and both end flanged including making cut mark in flanges for smooth lowering into the tubewell alongwith suitable size nuts, bolts and washers etc, in replacement of existing u/s pipes complete all as specified and directed. Make: Jindal/ Tata/ Prakash surya.

GI column pipe medium grade ISI marked of size 100 mm bore each of three mtrs length and both end flanged including making cut mark in flanges for smooth lowering into the tubewell alongwith suitable size nuts, bolts and washers etc, in replacement of existing u/s pipes complete all as specified and directed. Make: Jindal/ Tata/ Prakash surya.

Labour only for servicing of LT starter panel in Pump House for safety checking and setting of relay and removing unserviciable copper cable and rewiring of existing size of copper cable, removing burned contractors, single phase preventer, standared operating coil, over load relay and fixing, commissioning and testing of Panel, complete all as specified and directed. Note:- (a) Spare parts shall be measured and paid seperately. (b) Any other small items required to make functional is deemed to be included in the quoted rate.

Supply only single phase preventor suitable for 3 phase, 415 Volts including all necessary wiring. Make : Minilac or equivalent.

Supply only 3 pole power contactor ML-1.5. Make : L&T Cat No SS91851COOO /Havells/BCH.

Supply only 3 pole power contactor ML-2. Make : L&T Cat No CS96005LCOOO /Havells/BCH.

Supply only 3 pole power contactor ML-3. Make : L&T Cat No CS90907LOOO /Havells/BCH.

Supply only 3 pole power contactor ML-4. Make : L&T Cat No CS96006LOOO /Havells/BCH.

Supply only standared operating coil ML-1.5 for voltage 440 Make : L&T Cat No SS90873POOO /Havells/BCH.

Supply only standared operating coil ML-2/ML-3 for voltage 440 Make : L&T Cat No SS90873POOO /Havells/BCH.

Supply only overload relay range 13-21 Amp 230 Volt. Make : L&T Cat No SS91859OOCO / Havells / BCH or equivalent.

Supply only overload relay range 20-32 Amp 230 Volt. Make : L&T Cat No SS91859OOEO / Havells / BCH or equivalent.

Supply only overload relay range 28-42 Amp 230 Volt. Make : Havells/L&T/BCH or equivalent.

PVC insulated single core copper conductor flexible PVC insulated heavy duty industrial Cables (Unsheathed) of nominal area of conductor 25 sqmm,1100 Volts, conforming to IS: 694 in replacement of old detriorated cable, complete all as specificed and directed by Engineer-in-Charge.

PVC insulated single core copper conductor flexible PVC insulated heavy duty industrial Cables (Unsheathed) of nominal area of conductor 16 sqmm,1100 Volts, conforming to IS: 694 in replacement of old detriorated cable, complete all as specificed and directed by Engineer-in-Charge.

PVC insulated single core copper conductor flexible PVC insulated heavy duty industrial Cables (Unsheathed) of nominal area of conductor 10 sqmm,1100 Volts, conforming to IS: 694 in replacement of old detriorated cable, complete all as specificed and directed by Engineer-in-Charge.

Dismantling and taking down existing unserviceable chloronome plant and replacement of unsv pump tube, injection check valve, connecting nut with adopter, discharge tubing minimum 20 mtr and refixing the same and testing complete all as specificed and directed by Engineer-in-Charge. Make : RAMCO / Declibac or equivalent.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

Rolled mild steel joist, channel, angle, flat iron or Tee sections, fixed independently without connecting plates etc, confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed.

Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe – 410 – W (Gde E - 250) quality 'B' complete all as specified and directed.

MS pipes (ERW steel) including cutting, bending and welding as per site requirement and specials with flanged and drilled ends, jointing materials like nuts, bolts and gasket etc of nominal dia 250 mm as per IS 3589 (1981) thickness 6.0 mm, fixed in replacement of existing unserviciable pipe, complete all as specificed and directed by Engr-in-Charge.

Run lead joints for 150 mm bore cast iron spigot and socketed pipes and fittings by including jointing material i.e lead & spun yarn in repairs , complete all as specified and directed by Engineer-in-Charge.

Run lead joints for 100 mm bore cast iron spigot and socketed pipes and fittings by including jointing material i.e lead & spun yarn in repairs , complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) any description and laid in any position complete all as specified and directed.

Plain cement concrete, (1:4:8), type D-2, using 40 mm graded mechanically crushed stone aggregates as in foundation, filling and mass concrete complete all as specified and directed.

Preparation of old steel or iron surfaces such as MS fencing posts, MS/CI pipes and likes of any description, exceeding 10 cm width or girth of any description and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

Preparing new or previously untreated surface such as MS angle, plate, MS/CI pipes and likes of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer , complete all as specified and directed by Engineer-in-Charge.

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories, fixed in replacement of existing unserviciable valve required:- (a) Valve size : 100 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modern compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make: MARSH (emtork) / RITETORK / HASSEL HOFENER / RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories, fixed in replacement of existing unserviciable valve required:- (a) Valve size : 150 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modem compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make: MARSH (emtork) RITETORK / HASSEL HOFENER / RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories, fixed in replacement of existing unserviciable valve required:- (a) Valve size : 200 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modem compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make: MARSH (emtork) / RITETORK / HASSEL HOFENER / RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Supply, fixing, testing and commissioing of DOL STARTER, AC 3 phase, 415 volts, 50 Hz with sheet metel encloser with wide band coil heavy duty with single phase preventer suitable for 10 HP motor and making connection with suitable size of copper cable including taking down old unservicable starter of any type and capacity complete all as directed by Engineer-in-Charge. Make : L&T TYPE MU-G10H DOL HSN CODE 8536 CAT NO OF COIL VOLTAGE 360 VOLTAGE SS95974COFOO AND CAT NO OF COIL VOLTAGE 415 V IS SS95974DOFO or equivalent.

Supply, fixing, testing and commissioing of STAR DELTA STARTER, AC 3 phase, 415 volts, 50 Hz with sheet metel encloser with single phase preventer with wide band coil heavy duty suitable for 20 HP sebmersible pump and making connection with suitable size of copper cable including taking down old unservicable starter of any type and capacity complete all as directed by Engineer-in-Charge. Make : L&T TYPE MU-G20H FASD HSN CODE 8536 CAT NO OF COIL VOLTAGE 360 VOLTAGE SS95975COFOO AND CAT NO OF COIL VOLTAGE 415 SS 95975DOFO or equivalent.

Supply, fixing, testing and commissioing of STAR DELTA STARTER, AC 3 phase, 415 volts, 50 Hz with sheet metel encloser with single phase preventer with wide band coil heavy duty suitable for 40 HP sebmersible pump and making connection with suitable size of copper cable with Mn 5 Relay range 30-60 including taking down old unservicable starter of any type and capacity complete all as directed by Engineer-in-Charge. Make : L&T TYPE MU-G40H FASD HSN CODE 8536 CAT NO OF COIL VOLTAGE 380 VOLTAGE CS90908LOTO or equivalent.

Supply, fixing, testing and commissioing of STAR DELTA STARTER, AC 3 phase, 415 volts, 50 Hz with sheet metel encloser with single phase preventer with wide band coil heavy duty suitable for 75 HP sebmersible pump and making connection with suitable size of copper cable with Mn 5 Relay range 66-110 including taking down old unservicable starter of any type and capacity complete all as directed by Engineer-in-Charge. Make : L&T TYPE MU-G75 FASD HSN CODE 8536 CAT NO OF COIL VOLTAGE 380 VOLTAGE CS96451LOKO or equivalent.

Supply, fixing, testing and commissioing of Electric Water Pump (Presure Pump) self priming 0.37 KW / 0.5 HP 220 V, 50 Hz including making connection with suitable size of copper cable including taking down old unservicable electric water pump of any type and capacity complete all as directed by Engineer-in-Charge. Make : Crompton Ser No LPEC1SB050366 / KIRLOSKAR or equivalent.

Supply only lead wool for using of CI pipes joint filling complete all as directed.

Supply only spun yarn complete all as directed.

Cast iron foot valve of size 80 mm dia flanged ends with swing type operation with rubber seat conforming to IS :4038 and all accessories including suitable nuts, bolts, washers etc, including taking down old unservicable foot valve, complete all as specificed and directed by Engineer-in-Charge. Make : KIRLOSKAR or equivalent in KARTAR /BIR.

Cast iron foot valve of size 100 mm dia flanged ends with swing type operation with rubber seat conforming to IS :4038 and all accessories including suitable nuts, bolts, washers etc, including taking down old unservicable foot valve, complete all as specificed and directed by Engineer-in-Charge. Make : KIRLOSKAR or equivalent in KARTAR /BIR.

Cast iron foot valve of size 150 mm dia flanged ends with swing type operation with rubber seat conforming to IS :4038 and all accessories including suitable nuts, bolts, washers etc, including taking down old unservicable foot valve, complete all as specificed and directed by Engineer-in-Charge. Make : KIRLOSKAR or equivalent in KARTAR /BIR.

Cast iron foot valve of size 250 mm dia flanged ends with swing type operation with rubber seat conforming to IS :4038 and all accessories including suitable nuts, bolts, washers etc, including taking down old unservicable foot valve, complete all as specificed and directed by Engineer-in-Charge. Make : KIRLOSKAR or equivalent in KARTAR /BIR.

Cast iron non return valve of size 250 mm bore, disc flap type with flanged and drilled ends with bypass arrangement conforming to IS-5312 Part-I including 02 Nos flanges and jointing material like nuts, bolts, washers and gasket etc, including taking down old unservicable NRV, complete all as specificed and directed by Engineer-in-Charge. Make: LEADER or equivalent in KARTAR/BIR.

Fixing only cast iron non return valve of size 150 mm bore, disc flap type with flanged and drilled ends with bypass arrangement conforming to IS-5312 Part-I including 02 Nos flanges and jointing material like nuts, bolts, washers and gasket etc, including taking down old unservicable NRV, complete all as specificed and directed by Engineer-in-Charge. Note:- CI NRV shall be issued under Schedule 'B'.

Fixing only cast iron non return valve of size 100 mm bore, disc flap type with flanged and drilled ends with bypass arrangement conforming to IS-5312 Part-I including 02 Nos flanges and jointing material like nuts, bolts, washers and gasket etc, including taking down old unservicable NRV, complete all as specificed and directed by Engineer-in-Charge. Note:- CI NRV shall be issued under Schedule 'B'.

Fixing only cast iron non return valve of size 80 mm bore, disc flap type with flanged and drilled ends with bypass arrangement conforming to IS-5312 Part-I including 02 Nos flanges and jointing material like nuts, bolts, washers and gasket etc, including taking down old unservicable NRV, complete all as specificed and directed by Engineer-in-Charge. Note:- CI NRV shall be issued under Schedule 'B'.

Cast iron non return valve of size 50 mm bore, disc flap type with flanged and drilled ends with bypass arrangement conforming to IS-5312 Part-I including 02 Nos flanges and jointing material like nuts, bolts, washers and gasket etc, including taking down old unservicable NRV, complete all as specificed and directed by Engineer-in-Charge. Make: LEADER or equivalent in KARTAR/BIR.

Cast Iron sluice valve 150 mm bore both end flanged, long body, class PN-1.6 confirming to IS 14846-2000, duly ISI marked with iron wheel and brass spindle and non rising stainless stem with gun metel parts flanged drilled to IS 1538, fly nut, bolts, washers and rubber gasket etc, including taking down old unservicable sluice valve, complete all as specificed and directed by Engineer-in-Charge. Make : Zoloto art No 1079B HSN code : 84818030 / KIRLOSKAR or equivalent in KARTAR/BIR.

Fixing only cast Iron sluice valve 100 mm bore both end flanged, long body, class PN-1.6 confirming to IS 14846-2000, duly ISI marked with iron wheel and brass spindle and non rising stainless stem with gun metel parts flanged drilled to IS 1538, fly nut, bolts, washers and rubber gasket etc, including taking down old unservicable sluice valve, complete all as specificed and directed by Engineer-in-Charge. Note:- CI Sluice Valve shall be issued under Schedule 'B'.

Fixing only cast Iron sluice valve 80 mm bore both end flanged, long body, class PN-1.6 confirming to IS 14846-2000, duly ISI marked with iron wheel and brass spindle and non rising stainless stem with gun metel parts flanged drilled to IS 1538, fly nut, bolts, washers and rubber gasket etc, including taking down old unservicable sluice valve, complete all as specificed and directed by Engineer-in-Charge. Note:- CI Sluice Valve shall be issued under Schedule 'B'.

Cast Iron sluice valve 50 mm bore both end flanged, long body, class PN-1.6 confirming to IS 14846-2000, duly ISI marked with iron wheel and brass spindle and non rising stainless stem with gun metel parts flanged drilled to IS 1538, fly nut, bolts, washers and rubber gasket etc, including taking down old unservicable sluice valve, complete all as specificed and directed by Engineer-in-Charge. Make : Zoloto art No 1079B HSN code : 84818030 / KIRLOSKAR or equivalent in KARTAR/BIR.

Ball valve of 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) & fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply, fixing, testing and commissioing of submersible monoblock pump set three phase of capacity 5 HP and making connection with suitable size of copper cable including taking down old unservicable monoblock pump set of any capacity complete all as directed by Engineer-in-Charge. Make : Kirloskar KOS 520+ or equivalent.

Supply, fixing, testing and commissioing of swimming pool centrifugal pump set three phase of capacity 3 HP and making connection with suitable size of copper cable including taking down old unservicable monoblock pump set of any capacity complete all as directed by Engineer-in-Charge. Make : Kirloskar Etrena swimming pool pump model No KPP2200 or equivalent.

UPVC pipes for the following dia (IS : 4985 - 2000) class V 10 Kg/cm2 pressure including injection moulded fittings (heavy duty) with accessories bends, junction tee, access piece etc, clamps / supports jointing with ruber ring / solvent cement joint including cutting chase or holes in wall, floor and making good as required at site, including taking down old unservicable pipe, complete all as specificed and directed by Engineer-in-Charge:- Make : SUPEREME / PHENOLEX / PRINCE

63 mm outer dia

90 mm outer dia

160 mm outer dia

200 mm outer dia

250 mm outer dia

Wafer type cast iron butterfly valves of size 50 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 65 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 80 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 100 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 150 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 200 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Wafer type cast iron butterfly valves of size 250 mm of PN-1.6 with SG iron disc, body SG iron without lugs lever operated Nitrile EDPM rubber lining including flanges and all accessories including taking down old unservicable butterfly valve, complete all as specificed and directed by Engineer-in-Charge.

Motorised door chain suitable for 2 HP Motor as per existing size including taking down old unservicable motorised door chain, complete all as specificed and directed by Engineer-in-Charge.

MCCB four pole 63 Amps with breaking capacity 16 kA, 415 Volts, fixed thermal & magnetic release including making all incoming / outgoing connections fixed as in repair complete all as specified and directed by Engineer in Charge. Make :- Legrand / L&T / Schneider / C&S / Havells or equivalent.

MCCB four pole 100 Amps with breaking capacity 16 kA, 415 Volts, fixed thermal & magnetic release including making all incoming / outgoing connections fixed as in repair complete all as specified and directed by Engineer in Charge. Make :- Legrand / L&T / Schneider / C&S / Havells or equivalent.

MCCB four pole 160 Amps with breaking capacity 25 kA, 415 Volts, fixed thermal & magnetic release including making all incoming / outgoing connections fixed as in repair complete all as specified and directed by Engineer in Charge. Make :- Legrand / L&T / Schneider / C&S / Havells or equivalent.

MCCB four pole 250 Amps with breaking capacity 35 kA, 415 Volts, fixed thermal & magnetic release including making all incoming / outgoing connections fixed as in repair complete all as specified and directed by Engineer in Charge. Make :- Legrand / L&T / Schneider / C&S / Havells or equivalent.

Supply and fixing in repair cylindrical sealed disposal sanitiser refill (Stequa 411 AE) for disinfection of drinking water with arrangement for controlled release of dis infant in water suitable for operation through suitable feeder complete all as specified and directed by Engineer in Charge. Make : Declibac item No S411AE or equivalent.

Supply, fixing, testing and commissioing of Furculator motor 3 HP 415 V, 50 Hz including taking down old unservicable furculator motor of any type and capacity complete all as directed by Engineer-in-Charge. Make : Crompton / Kirloskar or equivalent.

GI tubing light grade 50 mm bore for protection for cable under roads, crossings/ culverts including jointing at ends, including taking down old unserviciable GI tube of any grade and size, complete all as specificed and directed by Engineer-in-Charge.

Taking down existing old unserviceable underground LT cable upto size 50 Sqmm, 4/3.5 /2 core keeping aside for reuse/removal from trenches/ wall/pole , complete all as specified and directed by Engineer-in-Charge.

Taking down existing old unserviceable underground LT cable upto size 70 to 150 Sqmm x 3.5 Core keeping aside for reuse/removal from trenches/ wall/pole , complete all as specified and directed by Engineer-in-Charge.

Taking down existing old unserviceable underground LT cable upto size 185 to 240 Sqmm x 3.5 Core of keeping aside for reuse/removal from trenches/ wall/pole , complete all as specified and directed by Engineer-in-Charge.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size of 16 Sqmm 4 core, laid in trenches or under road , complete all as specified and directed by Engineer-in-Charge. Note: Excavation, sand and brick work will be measure & paid separately.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size of 95 Sqmm 3.5 core, laid in trenches or under road, complete all as specified and directed by Engineer-in-Charge. Note: Excavation, sand and brick work will be measure & paid separately.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size of 120 Sqmm 3.5 core, laid in trenches or under road, complete all as specified and directed by Engineer-in-Charge. Note: Excavation, sand and brick work will be measure & paid separately.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size of 240 Sqmm 3.5 core, laid in trenches or under road, complete all as specified and directed by Engineer-in-Charge. Note: Excavation, sand and brick work will be measure & paid separately.

Excavation in trenches not exc 1.5m wide and and not exc. 1.5m depth wide in hard/dense soil for laying electric cables/pipes etc including getting out excavated earth and trimming the sides and bottoms of trenches , complete all as specificed and directed by Engineer-in-Charge.

Returning , filling in including spreading, leveling, watering and well ramming in layers not exc. 25cm in hard and dence soil, complete all as specificed and directed by Engineer-in-Charge.

Removal of surplus soil to a distance not exc. 50m and depositing where directed at a level not ex. 1.5m above the starting point , complete all as specificed and directed by Engineer-in-Charge.

Sand cushioning to cables with a layer of sand 8 cm deep before laying the cable and 15 cm depth (punned down to 10 cm depth after laying and stretching of cable), complete all as specificed and directed by Engineer-in-Charge. Note: Punned thickness (over all 18 cm) shall be measured & paid.

Brick of common burnt clay, sub class 'B' old size laid flat and dry on cables as in cable protection in trenches over cables perpendicular to direction of cables abutting each other , complete all as specified and directed by Engineer-in-Charge.

Cleaning and scraching the surfaces of filter bed, walls, floor truffs , drains etc by wire brushes or otgher wise to remove the deposited mud and waste materials etc washing the filter bed with clean water complete all as directed by Engineer-in-charge.

Taking out U/S exiting filter media from filtter bed of any size/depth including removing material to distance exceeding 50 meter but not exceeding 100 meter complete all as directed by Engineer-in-charge.

Supply and laying the natural gravel pebbles of size 20 mm to 40 mm grades all as directed by Engineer-in-charge.

Supply and laying the natural gravel pebbles of size 10 mm to 20 mm grades all as directed by Engineer-in-charge.

Supply and laying the natural gravel pebbles of size 06 mm to 10 mm grades all as directed by Engineer-in-charge.

Supply and laying the natural gravel pebbles of size 02 mm to 06 mm grades all as directed by Engineer-in-charge.

Supply and laying white silica sand filter media of effective size 0.5 mm to 2mm as per sample in GE office complete all as directed by Engineer-in-charge. Note:- 1. Gravel for filter bed shall be obtained from approved source and filter sand shall be as per sample Kept in GE office.

Repair excluding spares of the Automatic water supply system installed at AF Stn Suratgarh including carrying out complete maintenance/serving/repairs as required of all the sub systems viz. PLC based control panels (with all the accessories), Mimic Panel, breakdown maintenance and replacement of unservicealbe parts, refixing of old serviceable parts / new parts if any including the followings and all as specified and directed by Engineer-in-Charge. Equipments:- (i) Automation Master Panel at water supply treatment plant (ii) Automation Slave Panel each at all the eight OHTs (iii) Automation Master Panel at Booster PH No. Clear Sump (iv) Automation Slave Panel for Borewell each at ATC OHT (v) Mimic panel Notes:- (i) New parts if any shall be paid under separate items as supply only (ii) The scope of work includes the charges required for removing, repairing, refixing, carrying out electrical termination and fixing/installing, testing, commissioning, etc and all as directed.

Servicing of pressure switch i.e Cleaning checking for wear and tear, checking electrical termination, testing and breakdown maintenance and replacement of unserviceable parts if any all as specified and directed by the Engineer-in-Charge:- Note:- (i) The scope of work includes only labour charges required for removing, repairing, refixing of serviceable old parts / new if any carrying out electrical termination and fixing/ installing, testing, commissioning etc. complete (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Solenoid Valves of size 10mm/15mm i.e Cleaning checking for wear and tear, checking electrical termination, testing and breakdown maintenance and replacement of unserviceable parts if any all as specified and directed by the Engineer-in-Charge:- Note:- (i) The scope of work includes only labour charges required for removing, repairing, refixing of serviceable old parts / new if any carrying out electrical termination and fixing/ installing, testing, commissioning etc. complete (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Motorised Butterfly Valves and connected items of Size200/ 150mm/100/80mm i.e cleaning, greasing, checking for wear and tear, checking electrical termination, testing and breakdown maintenance and replacement of unserviceable parts, refixing of serviceable parts / new parts if any testing, commissioning etc complete and all as specified and directed. Note : (i) The scope of work includes only labour charges required for removing, repairing, refixing carrying out electrical termination, and fixing/ installing, testing and commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Magnetic switch sensor i.e. cleaning, checking for wear and tear, checking electrical termination, testing and breakdown Maintenance and replacement of unserviceable parts, refixing of old surviceable parts / new parts if any testing, commissioning etc complete and all as specified and directed. Note : (i) The scope of work includes only labour charges required for removing, repairing, refixing carrying out electrical termination, and fixing/ installing, testing and commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Supply only Single Phase Preventor. Model :VSP D2 Make - Minilec/L&T/Telemechanic

Supply only Relay - 4 C/O, 220V Make : LEONE / IDEC/L&T

Supply only Relay– 4 C/O, 24 V Make : LEONE / IDEC/L&T

Supply only Indicator lamp of Colour : Red / Yellow / Green Make : ESBEE / Telemacnique /L&T

Supply only Push Button with LED Indicator - 240V A.C. (Colour : Red / Yellow / Green) Make : ESBEE / Telemacnique / L&T

Supply only Rust Proof Maintenance free Mangentic Float Switch Sensor. Make : RECKTRONIC DEVICE & SYSTEM/CRISTAL/ SPLASH

Supply only Coil for Solenoid Valve - 10mm / 15mm 230 V AC. Make – AVCON/ROTEX/ASCO

Supply only Pressure switch 0 - 10 kg/sq.cm. Make:- Indfos/Danfoss/L&T

Supply only Electric motor suitabel for actuator for 250 mm dia. Butterfly valve Make:- Ritetork

Supply only Electric motor suitabel for actuator for 200 mm dia. Butterfly valve Make:- Ritetork

Supply only Electric motor suitabel for actuator for 150 mm dia. Butterfly valve Make:- Ritetork

Supply only Electric motor suitabel for actuator for 100 mm dia. Butterfly valve Make:- Ritetork

Supply only Electric motor suitabel for actuator for 80 mm dia. Butterfly valve Make:- Ritetork

Supply only Capacitor for Actuator suitable for 80mm/100mm/ 150mm/ 200mm dia. Butterfly Valve Make:- Ritetork

Supply only Resistor for Actuator suitable for 50 mm/80 mm/ 150 mm dia. Butterfly Valve Make:- Ritetork

Supply only Limit Switch for Actuator suitable for 50 mm/80 mm/ 150 mm/ 200 mm dia. Butterfly Valve Make:- Ritetork

Supply only 5 pair 0.5 mm dia. Armoured copper cable for sensor. Make:- Havells/Nicco/Plaza/Polycab.

Supply only 6 Core 1.5 sq.mm. PVC sheath PVC insulated copper armoured cable. Make:- Havells/Nicco/Plaza/Polycab.

Supply only 4 Core 1.5 sq.mm. PVC sheath PVC insulated copper armoured cable. Make:- Havells/Nicco/Plaza/Polycab.

Supply only 2 Core 1.5 sq.mm. PVC sheath PVC insulated copper armoured cable. Make:- Havells/Nicco/Plaza/Polycab.

S & F in replacement of GI tubing light grade 80 mm bore for protection for cable under roads, crossings/culverts including jointing at ends, complete all as specified directed by Engineer-in-Charge.

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 15 of tender documents.

MAJOR REFREGERATION AND ELECTRICALS

DASHMESH ENTERPRISES

m/s krishna builders