PROVISION OF COVERED SHED FOR UNSV MATERIAL AT BSO YARD AND OTHER SANCTIONED WORKS AT MIL STN ABOHAR.

Amount

Excavation in post holes each n. exc. 0.50Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface.

M&L for PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and shown on drawing.

M&L for PCC 1:2:4 type B-2 using 20mm graded stone aggregate as in foundation filling around posts and mass including necessary form work where ever required concrete complete all as specified and as directed.

S&F Structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified and as completed.

S&F mild steel purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and ounter sunk) forming holes, without any attachment

S & F exc 12mm dia & n. exc 20mm dia exc 30mm long MS screw bolt machine made with hexagonal or Square head at one end and screwed the other,screwed end fixed with washer complete

M&L for preparation of steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, all as specified and directed by Engr-in-Charge.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.55mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out on soft or loose soil

Excavating in trenches , n.exc 1.5m wide and n.exc 1.5 m depth for foundations in soft /loose soil all as specified and directed.

Returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm all in soil complete all as specified and as directed by Engineer-in-Charge.

Spreading and levelling in layers n.exc 25cm thick and well ramming including watering as required under floors; all as directed. (in floor with available earth from excavation approved by Engr-in-Charge.

M&LMoorum/ red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering.

M&L for Brick work using fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:2:4) Type B0 (using 12.50 mm graded aggregate0 used as in benching and coping.

M & L for rendering 15 mm thick on brick work or concrete surface in CM 1:4 finishing even and smooth without using extra cement, all as specified and directed by Engr- in- charge.

M & L two coats of cement base paint over new plastered surface including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L Hardcore Broken stone and boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and shown on drawing.

M &L For 100 mm thick PCC (1:2:4) type C2 (using 20 mm graded stone aggregate) as in floor finishing even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

Forming contraction(Dummy) joints 40 mm deep x10 mm Wide,filled with sealing compound grade A as specified and directed

M&L for 75 mm thick PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in plinth protection

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation of cols, bdy pillars, posts, struts, etc. filling and mass concrete complete all as specified and shown on drawing.

M & L for rendering 15 mm thick on brick work or concrete surface in CM 1:6 finishing even and smooth without using extra cement, all as specified and directed by Engr- in- charge.

M&L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping including slightly rounded or chamfered angles and including necessary form work.

M&L preparing newly plastered surfaces of wall, pilasters, cornices etc and applying two coat of water based exterior emulsion over and including a coat of primer as Approved by GE complete all as specified & as directed.

M&L for preparation of steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, all as specified and directed by Engr-in-Charge.

Removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.

M & L for Glazed ceramic light shade tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match in vertical surface in neat cement slurry and pointed in white cement paste pigmented to the shade over 10mm thick cement sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.

M&L for 25 mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in floor or laid under floor as setting coarse complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut 16 to 18 mm thick, Kota stone slab (size of slab not less than 500x550mm for flooring and in single piece for treads of staircase), laid over and including 20 mm thick bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish) and polishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut 16-18mm thick, Kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish ) and polishing by machine, including machine cutting to make it square or rectangular complete all as specified and as directed by Engineer-in-Charge.

supplied and fixed Welded steel wire fabric not exc 4Kg/Sqm cut to lengths, bent to shape required, including welded to steel members all as specified & directed by Engineer-in-Charge.

S&F Rolled sections/Squre Pipes as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with and including coach screw, bolt and washer in roof, wall etc.

M&L for Trial bore of 200 mm dia upto 200 meter depth below ground level in any kind of soil strata including hard stone/boulder including electric logging, MS cap, MS flat iron clamps, reducing socket etc.

M&L for Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water complete all as specified

M&L for Yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield complete all as specified

Supply jointing and lowering PVC slotted 150mm dia heavy duty including providing suitable jail on the slotted pipe complete all as specified

Supply jointing and lowering PVC 150mm dia heavy duty pipe including joints complete all as specified

Supply, Installing, lowering, Connecting, Commissioning and Testing submersible solar pump of discharge 272 LPM at 30 Mtr head coupled with 3 phase AC motor of capacity 5 HP including 2 inch HDPE delivery pipe with clamp, rope, 03 core SB wire of size 06 sqmm from starter to summercible pump complete with 5 KW solar panel of latest technology (Panel Size and Specification approved by GE) with GI structure, solar controller, modules, lightening arrester, Earthing, feeder pillar box with VFD starter and necessary plinth works as specified by company, complete all as specified and directed.

M&L for Point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories including PVC rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of modular switchs, sockets, fan regulator etc covered with Modular sheet and covers sheet of required size fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly completed, cost of modular sheet and cover are included in the item rate complete following all as specified

One light point/Fan point/Exhaust controlled by one way switch

One 5 pin socket out let 5 amps on the same board with other switches

One 5 pin, 5A socket outlet point on independent board with other switches.

All as per item no. 46 here-in-before but with 2.5 sqmm cable for 1No 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified

All as per item no. 46 here-in-before but with 4.0 sqmm cable for 1No 16 amps socket outlet point on independent board including 4.0 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified

S&F Modular switch 1 way 6 Amps, 1 module 230 volt AC supply complete all as specified

S&F Modular Socket, 6A - 2/3 pin combined 2 module, 230 volt AC supply complete all as specified.

S&F Modular switch 1 way 16A, 1 module 230 volt AC supply complete all as specified

S&F Modular Socket 6A/16A - 2/3 pin combined, 2 module, 230 volt AC supply complete all as specified

S&F Ceiling rose surface type, 65mm x 50mm three terminals, 3 phase / PVC / polycarbonate isolated body all as specified

S&F ,Modular step fan regulator 120 W - 2 module all as specified

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for LED bulb fittings icluding 12 Watt LED Bulb complete.

Supply and fixing LED lights fitting 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F sheet metal enclosure for DB's SPN 230 volts 8 way with 200 amps rated bus bar neautral link, earth bar double door complete all as specified

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified

M&L for submain wiring comprising single core , 2 Runs of 10 sqmm nominal cross sectional area multi stranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. in surface/recessed PVC conduit and its fittings complete including provision of 1X10 sqmm nominal cross sectional area multi stranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS and specified and making good all disturbed work to match the existing complete incl taking down old UNSV sub main complete all as specified and directed by Engr-In-charge.( Note :- Extra length of cables/ wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

Earthing complete with galvanised steel earth plate electrode of size 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 m below normal GL connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers and earth strip protected by 15 mm dia GI pipe medium grade and connected to main distribution board panel/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion including taking down old Unserviceable earthing any type all as specified

Supply and fixing ceiling fans completewith blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete.

Excavation in trenches any type of soil , n exc 1.5m wide and n exc 1.5m in depth , for foundation , etc or for shaft, well, cesspits , manholes , pier hole etc n exc 1.5 m in depth and getting out for laying of cable complete all as specificed and directed.

Returning , filling in including, spreading , levelling , watering and well reamming in layers not exc. 25 cm within the 1 mtr strech complete all as specificed and directed.

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

Removal of excavated material to a distance not exc 50 mtr and depositing where directed at level not exc 1.5 mtr above the starting point complete all as specified and directed.by Engr-in-charge

Supplying and laying reinforced precast concrete cable cover Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and directed.

SHRI SHYAM CONSTRUCTION CO. (BID ID -3336108)

Easyways Enterprises (BID ID -3341869)