SPECIAL REPAIRS TO BUILDING NO T- 19, P-04 and P-63, STREET LIGHTS AT PFFR POKARAN MIL STN UNDER AGE (I) POKARAN

Amount

Dismantling Stone slabs in roofs, suspended floors , chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed by the Engineer-in-Charge.

Demolition of concrete of any description and in any position (PCC Padding over roof) complete all as specified and as directed by the Engineer-in-Charge.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates,Fe 410-W (Gde E-250) quality A

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6, except stone slabs complete all as specified and as directed by the Engineer-in-Charge

M&L for Flush Pointing single joints in brickwork or masonry in detached work, flashings, etc. on ceiling in CM (1:4) complete all as specified & directed.

M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness 50 mm as per the requirements all as directed by Engr-in-Charge.

M&L for 10mm thick screed plaster on roof for laying in CM 1:3 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only)

Supply only integral water proofing compound.(ISI Marked)

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced all as specified and as directed , Four course roof treatment consist of as under :-(i) Applying one coat of bituminous primer conforming to IS-3384 @0.3 Ltr per sqm (ii) Laying of APP based membrane as specified thickness and weight (iii) Applying one coat bitumen grade 85/25 @ 1.2 Kg/Sqm (iv) Applying one coat of aluminium paint @ 100 ml/sqm

M&L for roughly squared stone 5cm thick as in lintels n exc 3m in length, hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Vitrified ceramic tiles , Light Shade, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set jointed and pointed in white or coloured cement to match the colour of tiles with screed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6. all as specified.

M&L Vitrified light colour Ceramic tile 9 to 10 mm thick (Square/rectangular) polished, area of each tile not exc 0.36 sqm in Skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick plaster in cement mortar 1:3 on Stone Masonary Surfaces Complete

S&F for Non- skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with screed bed 15 mm thick CM 1:6 complete all as specified & directed

M&L Glazed ceramic coloured tiles in vertical surface 600mm x300mm , 7-8mm mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick plaster in cement mortar 1:3 on Stone Masonary Surfaces Complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 300 x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering CM 1:3 over Stone masonary Surfaces complete all as specified and directed.

Material and labour for Granite(of any type) 18 to 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar

M&L for machine kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 15 mm thick screed bedding in CM (1:3)

Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting,dado,and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 10 mm thick backing coat of CM (1:3)

Demolition of stone/ boulder masonry and built in cement mortar all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge.

M&L for Brickwork with flyash bricks,modular size, straight or curved on plan to any radius in half brick thick walls built in CM 1:6

M&L Rendering 10mm thick on fair faces of brick work or concrete surfacesin CM 1:6, Surface finished even and fair w/o using extra cement

Excavation in trenches n.exc 1.5m deep and n.exc 1.5m wide in manholes,etc. n getting out any type of Soil

Returning filling in soil including spreading, levelling and well ramming in layers n.exc 25cm thick in layer etc all complete.

Removing excavated soil material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for PCC ( 1:3:6) Type C-2 using 40 mm graded aggregate as directed by incharge

M&L For Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in sub bases all as specified.

Taking down cement plaster on brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in 1:4 cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for 10 mm thick , plaster in cement mortar (1:4) on surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge.

M&L preparation of new wall surface and applying two coats of distemper oil emulsion over a coat of alkali resistant primer,including one or more coat of wall care putty on wall complete all as specified and directeded.

M&L for preparation of new plastered surfaces as in ceilings, applying 3 coats of white wash complete.

Complete preparation old / new surfaces of walls and preparation of surfaces (external faces) of walls and applying two coats of external weather proof paint of Apex or equivalent over a coat of primer (self coat) complete all as per manufacturers instructions, complete all as per specified and directed.

Complete removal of existing treatment and applying one coat wall care putty on plastered surface, preparatory to distempering, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of OBD on wall.

M&L for Two coats of white wash on ceiling including preparation of complete removal of existing surfaces, complete all as per specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed by the Engineer-in-Charge

M&L for Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410-W (Gde E-250) quality A

S&F 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated

S & F, 35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified & directed by Engineer-in-charge.

S&F PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per Engr - in - charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suplying & fixing in the frame at site as per directed by Engr - in- charge.

S&F 100 mm long mild steel but hinges medium weight colld rolld.

S&F 150 mm long Aluminium anodised barrel tower bolt of extruded section.

Supply and fix 150mm long Extruded aluminium alloy handles, 150mm long fabricated type., anodised

S&F 300 mm long Aluminium allow anodised sliding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow.

S&F floor door stopper of aluminium 150mm size.

S&F, Powder coated, anodised aluminium frame & shutter for door, window and ventilator including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, etc complete all as specified & directed by Engineer-in-charge.

M&L for sheet glass 5.5mm thick, ordinary quality and glazing with, rubber packing exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

M&L Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufactures

S&F 2 levers brass mortice lock vertical type, size 100mm including escutcheon plates and two kays complete all as specified & directed by Eng-in-Charge

Supply and fix in repairs Aluminium (extruded section body), Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed

M&L for II nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S& F 25mm thick , Block boards, grade 1 quality, exterior grade, decorative type with decorative face veneers on both faces, fixed with screws to timber frame-work

S&F Secound Class Hardwood, plain fillets square rectangular or trangular in section wrought sectional area exceeding 13 sqcm and n exc 25 sqcm fixed with nails, bullnosed, splayed, chamfered or rounded on one edge or face

S&F Secound Class Hardwood, plain fillets square rectangular or trangular in section wrought sectional area exceeding 3 sqcm and n exc 6 sqcm fixed with nails.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 40mm ( when open)

S&F hasp staple safty type brass with mild steel hinge pin incl bolt and hinge plate 125mm long

S&F ball catches with 8mm dia steel ball & brass body & sticking plate incl fixing

S&F 100 mm long Aluminium anodised barrel tower bolt of extruded section .

Supply and fix Extruded aluminium alloy handles, 100 mm long fabricated type., anodised

S&F stainless steel wire cloths 0.36mm nominal dia of wire and averaging width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

Preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and direction.

Preparation of new Steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and direction.

Demolition of wall ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets.

S&F ,10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium / G.I./M.S. as per specification and drawing, including Anodised aluminium snap grid frame work for false ceiling all as specified

S&F Solid PVC wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

Dismantling frame timber scantling 4 sqcm and over in section in any postion all as specified & directed by engineer in charge

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240

S & F Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade Fe 410-W (Gde E-250) quality B

S & F Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long, Exc 20 mm, not exc 25mm.

M&L for Cement concrete in foundations, filling and mass-concrete Type B2 1:2:4 (40 mm graded aggregate)

S&F wind ties for roof including securing bolts;including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering

S & F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. Fixed as in Ridge.

Supply and fix repairs decorative type curtain rod , stainless steel, 25 mm dia with not less than 1mm wall thickness complete all as specified and directed.

Supply and fix decorative type brackets , stainless steel, suitable for above curtain rod complete all as specified and directed.

M&L for 5cm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete complete all as specified and as directed by the Engineer-in-Charge

M&L for 50 mm thick PCC (1:3:6) type C-2 using 20 mm graded stone aggregate laid as in plinth protection including finishing the surface even & fair all as specified and directed by Engr-in-charge

Demolition of cement concrete unreinforced in groundfloors and pavings not exc 15cm thickness below or above ground level etc all as specified and as directed

Dismantling of water tanks and removing to store capacity of tank exc500 ltrs and n exc 1000 ltr including Supply and fix rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,1000 ltr capacity

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15 mm bore to walls, ceiling etc.including S&F Medium grade GI tubing 15 mm bore with all fittings , to walls, ceiling or laid in floors etc.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm dia pipe including S&F Medium grade GI tubing 20 mm bore with all fittings , to walls, ceiling or laid in floors etc.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 15 mm bore pipe.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 20 mm bore pipe.

S&F in repairs for stop cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore in repairs

S&F in repairs bib taps cast cipper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs

S&F Vitreous china coloured Wash Hand Basin 580MM X 450MM fixed in repairs including 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm bras CP waste fitting & 15 mm PVC connection pipe 450 mm long fixed in repairs

S& F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F towel rail 600 mm long of Brass C.P 'D' type fixed with and including chromium plated brass screws and wooden /plastic cheats in repairs

S&F in repairs for European type water closet,including plastic seat cover white, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device complete.

S&F in repairs CP Health faucet spray with 1.5m long pipe with wall hook & fixed in repair complete

Supply and fix in repairs Bib taps two way type , cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule 15 mm bore and fixed

S&F PVC connections 15 mm size with PTMT nuts to length 450 mm as in repairs

S&F PVC flushing cistarn 10 ltrs capacity ISI marked incl PVC damtake pipe PVC 450mm inlet etc all complete in repairs.

Cutting holes in to or through in brick or stone walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B1 as required, exc 150sqcm & n exc 400 sqcm complete all as specified and directed,

Dismantling of cast iron RCC, AC or PVC pipe jointed in CM any dia bore

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let

PVC (SWR) multi floor trap with grating including jointing with solvent cement 100 mm dia out let.

S&F PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls

S&F PVC (SWR) pipes of 75 mm dia, single socket fixed to walls

S&F 100 bore of pipe stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof.

S&F PVC (SWR) bends with access door of 110 mm dia, any radius

S&F PVC(SWR) bends with access door of 75 mm dia, any radius

S&F PVC (SWR) bends of 110 mm dia, any radius

S&F PVC (SWR) bends of 75mm dia, any radius

(PVC (SWR) vent cowl, 110 mm dia

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe 290.Gde-E-165

S &F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and decorative cast iron artical etc. Fe 410w, Gde E-250 Quality A

S&F staniless steel sink 1mm thick with drainage board for kitchen with plug , waste pipe , washers, including cantilever cast iron brackets , connecting union etc, overall size 915x460mm with bowl size 410x330x160mm .

Taking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing-N- capping or concealed conduit) complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories such as wooden gutties/rawal plug, screw etc including making good disturbed surface to match the existing surface all as specified & directed.

M&L for point wiring with PVC unsheathed cable single core stranded copper conductor 1.5 sq mm size, 1100 V grade, drawn into concealed conduit medium grade (ISI marked) not less than 20mm dia on surface with and including PVC unsheathed cable single core copper conductor 1.5 Sq mm as continuous earth wire all as specified & directed by Engr-in-charge for the following :- (a) One light/fan/Exh point controlled by one switch 5 Amp one way

All as per item no 123.but socket outlet 3pin 5 amps same board

All as per item no.123 but socket outlet 3pin 5 amps independent board

All as per item no.123 but One bell/ buzzer point controlled by one push button

All as per item No.123 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4.0 Sq mm multistranded copper conductor wire FRLS PVC insulated and 4.0 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

M&L in repair, Modular white cover plate with frame ( both inner plate & outer plate cover ), 1 module.

M&L in repair, Modular white cover plate with frame ( both inner plate & outer plate cover ), 2 module.

M&L in repair, Modular white cover plate with frame ( both inner plate & outer plate cover ), 3 module.

M&L in repair, Modular white cover plate with frame ( both inner plate & outer plate cover ), 6 module.

M&L in repair, Modular white cover plate with frame ( both inner plate & outer plate cover ), 8 module.

M&L in repair, Modular metal flush box 1 & 2 module

M&L in repair, Modular metal flush box 3 module

M&L in repair, Modular metal flush box 6 module

M&L in repair, Modular metal flush box 8 module

M&L in repair,Modular switch one way 6 Amp single pole & one modular.

M&L in repair,Modular bell push 6 Amp, 230 volt & one modular complete all as specified.

M&L in repair, Modular socket 6 Amp 2/3 pin combined shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L in repairs, Modular socket 16/6 Amp 3 pin combined shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L in repairs, Modular switch 16 Amp single pole one way ISI marked confirming to IS 3854 : 1997 or latest IS having finger proof terminals with captive screws having front fixing & removing features without removing plates.

S& F in repair, Electronic type modular fan regulator step type 120 watt, 230 volt. 01 module

S&F in repairs, MCB DBs sheet metal enclosures single phase and neutral 240 Volt with 200 Amps rated bus bar Double Door Type, 8 ways complete all as specified & directed

M&L in repairs, MCB SP 240 volts, 5 to 32 Amps, 10 KA

M&L in repairs, MCB SPN 240 volts, 40 Amps, 10 KA

S&F in repairs, Ceiling rose, 3 phase/PVC/polycarbonate, isolated body

S & F bell ding dong type 230 v, 50 Hz

S & F in repairs, Decorative box type fitting 1x 20w, blue coloured end caps, prewired for LED tube including LED tube 20 watts, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”. Make: Crompton Greaves/Havells/Philips.

S & F LED building Security light fitting 1x18watt with polycarbonate housing ,Aluminum gear tray duly prewired inbuilt LED module IP 65 Protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS,FI clamp including plinth with nut bolts etc complete all as specified and directed Make: Crompton Greaves/Havells/Philips.

S & F in repairs, Decorative box type fitting 1x 16w, blue coloured end caps, prewired for LED tube including LED tube 16 watts, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”. Make: Crompton Greaves/Havells/Philips.

M & L for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continious earth wire on pole, testing the earthing after completion all as specified and shown in electric plate No 5 of MES SSR Part-I 1991 print and as directed .

Taking down old unserviceable LT cable, supply and Laying in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer In charge of cross sectional area of 10 Sqmm 2 core.

Supply & Fixing Ceiling fan 1200 mm sweep 50 Hz, single phase including down rod all as specified and as directed by Engr-in-charge Make - Bajaj/Usha/Crompton/Havells

Excavation in trenches not exc 1.5m wide and n. exc 1.5M deep for fdn / trenches and getting out for soft / loose soil.

Removing excavated material n exc 50m and depositing at a level n.exc 1.5M above ground.

Returning/filling in layers, spreading leveling, watering and well ramming in layers n.exc 25m in sof/loose soil.

M&L for Tibba sand for sand cushioning to under ground cable including, spreading, leveling hand punning complete all as specified and directed.

Supply and laying Jodhpur stone patti for cable protection of lenth between 55 to 60 cm but width between 25 to 30 cm thicknes not less than 5 cm complete as per site requirement and direction of engineer in charge.

Refixg of existing serviceable tube light fitting including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed at site

Taking down old unserviceable existing street light any type such as fluorescent tube fitting/ HPSV/ HPMV fittings any wattage from the pole/ buildings, at any hight and refixing and connecting the same after repair all as specified & directed by Engineer-in-charge.

S & F LED street light fitting 1x30watt with pressure die cast aluminium housing, heat resistant toughened glass with frame, duly prewired in built LED module IP 66 Protection complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS clamp with nut bolts etc complete all as specified and directed Make: Crompton Greaves/Havells/Philips.

S & F LED building Security light fitting 1x20watt with polycarbonate housing ,Aluminum gear tray duly prewired inbuilt LED module IP 65 Protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS clamps with nut bolts etc complete all as specified and directed Make: Crompton Greaves/Havells/Philips.

S&F service connection of 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathed of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core multistandard cable flat or circular of 6 Sqmm 2 core including taking down old service cable complete all as specified & directed by Engineer-in-charge.

M/s Rashid Mohammed

M/s Shri Inder Construction Company