SPL REPAIR TO GATE NO 1 (SANCHI GATE)AN BARRACK NO 8 OF RMS AJMER AND BLDG NO P-1, P-1/A, B (MES OFFICE) AND BLDG NO NO 17, 21 AND BOUNDARY WALL, FENCING AND CONNECTED WORK AT MAIN GATE AND PROVN OF TOILET BLOCK NEAR BLDG NO T-13 OF 316 MED REGT AT A

Amount

Demolition of Lime concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and directed.

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and as directed.

Material & Labour for Non - skid coloured ceramic tiles 400x400x 7 to 8 mm thick (square), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material & Labour for Coloured glazed ceramic tiles in vertical surface 300x 450x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Material and labour for Machine cut kota stone slab flooring of size 550*550*18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified and directed.

All as per item no 7.00 but pre-polished kota stone as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.

Material & Labour for Granite work (Jet/Telephonic Black) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.

Material & Labour for 50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete all as specified and directed. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L PCC (1:4:8) Type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete and sub base surface finished even & fair complete all as specified and directed. .

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Dismantling Asbestos cement (corrugated of semicorrugated etc), any gauge, thickness, roof coverings complete all as specified and directed.

Supply and fixing pre-painted galvatume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified and directed.

Supply and fixing pre-painted galvatume aluminium zinc coating (AZ-150) GI based plain steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified and directed.

Dismantling unframed timber fillets,rails,posts,rafters,purlins etc under 40 sqcm in section complete all as specified and directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

S&F for 2nd class hard wood 30mm thick Plain, framed, panelled shutters (06 number of panels), with panels of timber flat on both sides (feather edged), or of 9mm BWP commercial veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete.

Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

S&F factory made Steel window/ ventilator glazed & gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary cooler arrangement in window & guard bars all as shown in drg No. CEBZ/TD/14/11 sh No 1/7 to 7/7 & specified. (Make M/S Surbhi Metal, M/S Jangid and equivalent).

Supply and fixing for 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane complete all as specified and as directed.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed.

S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed.

Supply & fixed MS helical door spring 150mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats complete all as specified and directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample complete all as specified and directed.

Supply & fixing in repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample complete all as specified and directed.

Supply & fixing in repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repaie complete all as specified and directed.

Supply & fixing in repair of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample as in repair complete all as specified and directed.

Demolition of brickwork or stone/boulder masanory,laid dry below or above ground level and removing material from site complete all as specified and directed.

Material & Labour brick work with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6 complete all as specified and directed.

Material & Labour for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

M & L for rough cast plaster using crushed stone of size between 6 mm to 10 mm, coarse sand and cement mixed in the ratio of (1:1:1) over and including rendering coat of 15 mm thick on fair faces of brick work or concrete surfaces or stone masonry surfaces or other than fair faces of brick work or on one side of lathing (on vertical surfaces) in cement mortar 1:4 finished even and fair including two coats of cement base paint complete all as specified and as directed.

Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified and directed. Note : (i) WPC shall be measured and paid separately.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

Material and labour for preparation of newly/old plastered surface of ceiling and applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper paint over a coat of 1mm thick putty complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper on walls over a coat of 1mm thick putty complete all as specified and directed.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applyingTwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.

M&L for two coat of synthetic enamel painting to steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed.

Supply & fixing of framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls complete all as specified and directed.

M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc complete all as specified and directed.

Demolition and breaking up of rain water pipe /UPVC pipe line 100mm/75mm dia incl all fittings complete all as specified and directed.

Supply & Fixed for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in floors or walls etc complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

Supply & Fixed for 75 mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall/floors etc complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

Supply & Fixed for 110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement complete all as specified and directed. .(Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

Supply & Fixed 110 mm bore UPVC (SWR) ( singleT) equal or unequal including jointing with solvent cement complete all as specified and directed.

Supply & Fixed 110 mm bore UPVC (SWR) branch piece,single ( singleY) equal or unequal including jointing with solvent cement complete all as specified and directed.

Supply & Fixed for 75 mm bore UPVC (SWR) bend including jointing with solvent cement complete all as specified and directed. .(Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S&F PVC (SWR) 75 mm bore branch piece (Tee) fixed to walls with cement joint with or w/o ovel access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Material and labour in repairs 75mm diaPVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material and labour in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Supply and fixing brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed. (Make: Jaquar Essco/Prayag/Plumber/Jal)

Supply and fixing low density polyethylene pipe connection with PTMT nuts suitable for 15 mm bore GI pipe 450 mm long of pressure rating 6 kg/cm² including brass union and washer ateach end, one end screwed to inlet of piller tap/cistern and other end to stop cock etc complete all as specified and directed.

Supply and fixing in repairs Vitreous China counter below W.H.B. white of size 570 x 445 mm, incl waste pipe and brackets etc complete all specified and all directed.

Supply and fixing in repairs Chromium plated brass pillar tap of size 15 mm in WHB/Kitcen sink etc complete all specified and all directed.

S & F in repairs Vitreous China, Squatting pan Orissa pattern size 580X440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing complete al as spd & directed.

Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet EWC with complete one set white ( incl all necessary accesories like rag bolts/gel gasket etc.(excluding flushing cistern & flush pipe ) with ‘P’ or ‘S’ trap of dia 100mm including provn of cement concrete bedding complete all as specified and directed.

Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

Supply and fixing plastic water closet seat white, closed pattern with flat bottom and cover and mild steel C.P. or Aluminum hinging device of any size complete all as specified and directed.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified.

Supply and fixing in repair 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge. (Make: Jaquar Essco/Prayag/Plumber/Jal)

Supply and fixing (in repair) stop valves concealed type, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions complete all as specified and directed.

Supply and fixing in repairs 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule complete all as specified and directed.

Supply and fixing in repair CP brass soap dish all as specified and directed.

Material and labour for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed..

S&F in repairs 20mm bore Gun-Metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire complete all as specified and directed.

All as per item no 83.00 but 20mm dia bore complete all as specified and directed.

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as and directed.

S&F M S plate or angle, channel, square cut or notched with riveted, bolted or welded attachment completed all as spd and directed.

M & L for preparation of old painted wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) including provn of 10mm dia deformed bar welded horizontally to bottom of frame conforming to Fe-290 ( Gde 165-E ) including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F hold fast of flat iron conforming to Fe-290 (Gde-E-165) including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed

S&F Jet flush including plate & PVC connection complete all as specified and directed.

S&F IInd Class Hard wod small fittings such as brackets of any type, latch and hinges blocks , shaped door and window stops and the like, incl all necessary labours; article n.exc 200cu.cm each

S & F framed work as in roof trusses purlin, rafter and batterns of angle or other section with gusset plates , rails , braces, etc complete of Fe 410-W (Gde E-250) , drilling for fixing of steel sheeting or other covering doors etc to be prepared for hanging complete all as spd and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confireming to IS 15658-2006 of 60 mm thickness M-35 grade laid over and including 50 mm thick sand cushion complete all as specified and directed.

Supply and fixing steel work in tabular truss including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st 240 etc confirming to fe-410-W (Gde-E-250) quality-A all as specified as directed.

M & L for vitrified ceramic dark tiles 10 mm thick (square/rectangular) polised area of each tile exc 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding screed bed 15mm in CM (1:6) complete all as specified and directed.

M & L for vitrified ceramic dark tiles in vertical surface such as skirting/dados etc 10 mm thick (square/rectangular) polised area of each tile exc 0.36 sqm etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding 10mm thick CM (1:4) as in backing coat complete all as specified and directed.

S&F for 2nd class hard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treatedsupplied and fitted to chowkats complete all as specified and directed.

Supply & fixed in repairs stainless steel sink , made out of 1.00mm thick sheet for kitchen oe laboratory with plug,washers, waste pipe, cast irn cantilever bracket incl bedding in cemen t mortar on dwarf wall or incl fixing cantilever brackets and connecting union to pipe incl waste pipe waste coupling etc of overall size 495x420 mm bowl size 410x330x160mm complete all as specified and directed.

Material and labour for Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete .

S&F 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, and both faces is covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick, and all around side faces is covered with decorative lipping complete prepared as cup board shutter and fixed with wooden frame-work complete alll as specified and directed

S&F MS butt hinge 50mm medium weight cold rolled incl necessary welding etc all as directed.

S & F IInd class hardwood chowkats and frames in cupboard plain fillets, square,rectangular or triangular in section (exc 13 sq.cm n. exc 25 sq.cm) clean sawn, with glue, pinned at joints and fixed with screw including add extra for 6mm thick external teak wood lipping 18/19mm and fixed with nails complete all as specified and as directed.

S & F 100mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F for 100mm aluminium handles, cast type, anodised complete all as specified.

Taking down shutters exceeding 1 Sqm and not exceeding 2 Sqm and removing from site, complete all as specified and as directed.

Taking down shutters not exceeding 1 Sqm and removing from site, complete all as specified and as directed.

S & F for in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S & F for in repairs Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws l complete all as specified and directed.

S&F hollow pvc wall cladding wood colour or any colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for injection grouting of construction joints with non shrink cement slurry admixed with epoxy grouting Cebex 100 of M/S Fosroc Chemical /SikaGrout -214 IN @ 300 mm C/C including of opening of cracks to a groove of size 12mm X 12 mm, Nozzle at 300 mm C/C including of opening of cracks to be grooved of size 10mm X 10mm fixing of nozzles with fast setting plugging compound Renderoc plug, cutting the extra length of nozzle after grouting all in complete as per manufacturers instructions including necessary scaffolding as required and as per the directions of Engineers incharge complete all as specified and directed.Seal the nozzle with Sikagard 694 F(l) or equivalent thixotropic epoxy putty after the refusal of grout material from the nozzle. Note: leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and directed.

M&L Examining concrete by tapping with light hammer and marking of the loose concrete areas of structural elements in straight line geometrical forms, grooving the edges same with grinder upto 5 -10 mm depth without damaging existing rebars, carefully removing unsound weak/ loose concrete/ cover & concrete around the rebars upto 10 mm depth by low impact high frequency hammer/ chipper without damaging the sound concrete, daily cleaning and stacking of debris at prescribed location in polypropylene/ paper bags, disposing off the debris so generated on weekly basis outside the premises, etc, complete all as specified and directed necessary scaff -folding complete all as specified and directed.

M&L for cleaning existing reinforcement with wire brush/rotary wire brush to make surface free from rust scales, loose material, dirt etc complete and applying two coats of alkaline rust converting primer Sika Rust Off 100 or ReArm Rust Remover with brush on the existing rebar for complete wetting of rusted metal surface and allowed to react it for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days including surface preparation. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth, complete all as specified and as directed.

M&L for Drilling & Re baring of 10 mm dia x 120mmdeep, thoroughly coated with Zinc based reinforcement epoxy AquaArm CoatZP complete all as specified and directed.

M&L Providing and Application Aqua Arm Coat-Zp/ Friazinc R as passivator/ Anti corrosion coating to the steel reinforcement shall be applied The material shall be two component, cement based polymer modified two component coating for corrosion protection. The material shall be prepacked and ready to use. It shall be fully compatible with the reinstatement methods adopted complete all as specified and as directed by Engrin-charge. This shall include surface preparation and errection of steel porps as required for the application. complete all as specified and directed.

M&L of two component solvent free epoxy bonding agent ReArm Superbond or equivalent for bonding old to new concrete . The ready to use epoxy bonding agent shall be applied over old concrete using brush after cleaning of surface of all dust or latiance. The material is supplied as a two part material in preweighed quantities for ready onsite mixing and use. The material shall exhibits the following properties Compressive strength 50 N/mm2 at 7D Flexural strenght 35N/mms at 7 D , Shear strength ION/mm2 at 7D and Tensile strength 20 N/mm2 and Bond Strength of ION/mm2.The new concrete shall be placed within the open time as specified by the manufacturer to ensure maximum bonding and application shall be as per the manufacturer instruction , complete all as specified and as directed.

Rebuilding the section of damaged RCC elements to its original size in thickness of 25mm by hand or spray application by Providing and applying Sika MonoTop@- 122F single component, fibre reinforced, sulphate resistant, low shrinkage, high performance cementitious structural repair mortar. Surface finish of the repaired surface by mortar prepared with Water proofing admixture WP-10 or Sika Latex SBR as specified or directed.

M & L for fixing GI nozzles in honey comb area and along crack lines at required spacing after drilling using mechanical tools and plugging it using two component, high strength, non-sag, epoxy compound with ASTM C881 Type I, Grade 3, Class B & C formulated to achieve adhesive bond strength with concrete substrate an average of 1 MPa at 7 days or concrete failure when tested to ASTM D4541; Compressive strength in excess of 40 MPa at 1 day & 60 MPa at 7 days when tested as per BS: 6310 Pt 2, Tensile Strength of 10 MPa at 7 days when tested as per BS: 6319 Pt 7 such as Sikadur ADH 2200 or as specified and directed. Epoxy grouting – Injection Low Viscous Epoxy Resin Grouting the cracks after fixing the injection ports at predetermine locations with the help of suitable injection grouting pumps at suitable pressures using two – component, high strength, low viscous (<350 cps @ ambient temperature) epoxy injection resin system having minimum pot life of 30 minutes at ambient temperatures, achieves compressive strength higher than 55MPa in 1 day & 65MPa at 7 days; Flexural strength higher than 55 MPa at 7 days; slant shear bond strength higher than 15 MPa in 7 days such as Sikainject 471 or as specied and directed.

Rebuilding the section of damaged RCC elements to its original size in thickness of 25mm by hand or spray application by Providing and applying Sika MonoTop@- 122F single component, fibre reinforced, sulphate resistant, low shrinkage, high performance cementitious structural repair mortar. Surface finish of the repaired surface by mortar prepared with Water proofing admixture WP-10 or Sika Latex SBR as specified or directed by engineer incharge.

M&L apply 12 mm plaster cover on the carbon fibre wraped structure in the ratio of 1:4 and admixed with WP-10 as specified or directed by engineer incharge.

M & L preparation old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and providing two coat of cement base paint complete all as specified and directed.

Excavation over area n exc 1.5 m deep and getting out in soft/loose soil complete all as spd and directed.

Removing excavated soil to a distance n exc 50m and depositing where directed at a level n exc 1.50m above the starting point complete all as spd and directed.

Excavation in post hole (or similar holes) each n.exc 0.5 cum and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50m and making good in hard/dense soil

M&L, for PCC 1:3:6 type C-2 in post holes and similar works complete all as specified and directed.

M& L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar (1:6) complete all as specified and directed.

All as per item No 127.00 here in before but except stone complete all as specified and directed.

Extra over random rubble stone walling for hammer dressing to face stones and dressing to face beds & joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as spd and directed.

S&F Mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

Raking out joint/pointing to random rubble or polygonal rubble uncoursed or brought upto course in cement mortar.

M&L for raised pointing to random or polygonal rubble,uncoursed or brought upto coursed in CM 1:4

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete,brick etc and making good disturbed ground and preparing post holes for providing new post in any type of soil complete all as specified and direted

Dismantling fencing wire mesh, any type complete all as spd and directed.

M&L for angle iron as in fencing post incl cutting tops to shape as directed, drilling holes, notching for wire etc. Flat iron, fillets ( for securing wire mess) incl. all necessary drilling bolting or riveting etc confirming to Fe 290 Gde E -165 complete all as specified and directed.

Supply only Chain link MS galvanised fencing as specified.

Fixing only chain link fencing including line wires, any mesh size, type of standards rail straining bolts etc,4mm dia.wire

S&F in repair of galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining bolts, including, securing or tying at crossings with provison of galvanised mild steel wire etc

Providing & Fixing concertena coil fencing with punched tape concertena coil 600m dia 10m openable length (total length 90m) having 50 Nos rounds per 6m length, up to 3.0m height of wall with angle iron Y shaped placed 2.0m or 3.00m apart all complete as per direction of engineer-in-charge, with reinforced barbed wire tape (R.B.T.)/spring core (2.5mm thick) wire of high tensile strength of 165 Kg/Sqcm with tape (0.52mm thick and weight 43.478 gm/metre (cost of M.S. Angle shall be paid separately under relevant items.)

S&F of mild steel screw bolts (machine cut) with hexagonal or square heads at one end to be fitted with washers and one hexagonal or square nut, n.exc. 5cm long dia of neck 12mm.

S & F in repair 70-80 mm thick sand stone kerb of roughly rectangular stones not less than of size- length 60 cm and width 30 cm , dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck flush complete all as specified and directed.

M&L for MS framed work such as 12mm square guard bars conforming to Fe 290-0 or Fe 330-0 welded to ventilator/window /gate complete all as specified and directed

Providing and fixing of Stainless steel grade 304 letters in English of minimize size 100 mm with 25 mm raising.. The letters shall be fixed with the help of stainless steel studs on existing granite wall which shall not be visible from the front. The stainless-steel studs shall be properly grouted with suitable sealant all as specified and directed by Engr in Charge

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth & getting out in hard soil complete all as specified and directed.

Returning, filling in incl spreading leveling, watering and well ramming in layer n.exc 25cm in layer in soft/loose soil complete all as specified and directed.

Use of waste for formwork to sides and soffits of plinth beam, sides of footings, bass of columns and similar work with rough finished surfaces etc complete all as specified and directed.

Use of waste for formwork to sides of columns and similar work with rough finished surfaces etc complete all as specified and directed.

Material & Labour for formwork to sides and soffits of beam, lintel rough finished surfaces etc complete all as specified and directed.

Use of waste for form work to soffits of suspended slabs, such as roof slabs and similar work; not exc. 200 mm thick for flat rough finish surfaces complete all as specified and directed.

Use of waste formwork to edges of concrete flats and similar works exc. 10 cm & not exc. 20 cm wide with rough finished surfaces etc complete all as specified and directed.

Material & Labour RCC M-25 design mix (using 20 mm graded stone aggregate.) in footings & plinth beams etc complete all as specified and directed.

Material & Labour RCC M-25 design mix (using 20 mm graded stone aggregate.) in columns etc complete all as specified and directed.

Material & Labour RCC M-25 design mix (using 20 mm graded stone aggregate.) in roof beams & lintel beam etc complete all as specified and directed.

Material & Labour RCC M-25 design mix (using 20 mm graded stone aggregate.) in roof slabs supported on walls etc complete all as specified and directed.

Material & Labour mild steel TMT bar 10 mm dia and over, cut to length, bent to shape required and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Material & Labour mild steel TMT bar 8 mm dia and over up to and including 10 mm dia in stirrups, cut to length, bent to shape required and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Material & Labour brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6 complete all as specified and directed.

Material & Labour for brick work with sub-class `B' bricks built in CM 1:4, straight or curved on plan exceeding 6 M mean radius using old size bricks in half brick thick wall etc complete all as specified and directed.

Material & Labour rendering 5 mm thick in CM 1:4 on concrete surface of ceiling & finished even & smooth without using extra cement complete all as specified and directed.

Supply and fixing solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet rein forced with MS square tube etc complete all as specified and directed.

Supply and fixing PVC factory made shutter solid, PVC moulded prelam coloured on both side door shutter with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design in framing at site as per specifications & drawings complete all as specified and directed.

Supply and fixing Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F one-piece EWC with soft close seat cover, ‘S’ Trap, twin flush fittings, Siphonic Jet Flushing and 3D flush as per catalogue No S1013176 of M/s Cera (CERA EWCs-CHILE) or equivalent of Make mentioned under Appendix "B" including ‘S’ trap, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed.

Supply and fixing vitreous china half stall urinal with grating and union complete set with 40 mm dia GI light grade waste pipe incl. brackets etc complete all as specified and directed.

Supply and fixing Vitreous China W.H.B. white oval type of size 570 x 445 mm, waste pipe and brackets etc complete all as specified and directed.

Supply and fixing 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule complete all as specified and directed.

S/F waste coupling chromium plated size 32 mm with long thread complete all as specified and directed.

Supply and fixing 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union complete all as specified and directed.

Supply and fixing aluminium hat & coat hooks solid body 125 mm to 175 mm fixed with brass screw complete all as specified and directed.

Supply and fixing low density polyethylene pipe connection with PTMT nuts suitable for 15 mm bore GI pipe 450 mm long of pressure rating 6 kg/cm² including brass union and washer ateach end, one end screwed to inlet of piller tap/cistern and other end to stop cock etc complete all as specified and directed.

Cutting existing water steel tubing 20mm bore galvanized iron pipe for alterations and provision for branch connection by inserting tee union elbow etc complete all as specified and directed.

Screwing existing steel tubing 20 mm bore for alteration or additions etc complete all as specified and directed.

Material & Labour CPVC tubing 15 mm dia medium grade galvanized with all fittings and fixed complete to brick/stone wall or laid in floor concealed complete all as specified and directed. (Make: Astral/Prayag/Finolex/Ashirwad)

Material & Labour CPVC tubing 20 mm dia medium grade galvanized with all fittings and fixed complete to brick/stone wall or laid in floor concealed complete all as specified and directed. (Make: Astral/Prayag/Finolex/Ashirwad)

Supply and fixing gun metal gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as specified and directed. (Make-Zoloto/NMC/Leader).

Material & Labour PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete all as specified and directed .

Material & Labour PVC (SWR) floor trap 75/110mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed .

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm dia complete all as specified and directed .

Supply and fixing stack clamps out of 40mm by 4 mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore etc complete all as specified and directed.

Supply and fixing rotational molded polyethylene water storage tanks white in colour, tripple layered with threaeded lid/cover (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position complete all as specified and directed.

Supply and fixing 20 mm PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed.

Material and labour for preparation of newly plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

Supply & fixed Powder coated aluminium doors/windows/ventilator fixed/openable/sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw, handles incl frame of minimum thickness 1.5mm etc complete all as specified and directed.

Supply & fixed 4.8 mm thick plain or tinted glass, ordinary quality and glazing rubber beading in square n exc 0.5 sqm in each pane complete all as specified and directed.

M & L for screed plaster 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces mixed with WPC incl necessary doubingout etc finished even and smooth for laying WPT without using extra cement complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces 75mm radius and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

M & L for APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed.

M & L for PCC 40mm thick (minimum Consolidated thickness) Type B-0 (1:2:4), using 12.5 mm graded crushed stone aggregate as in padding finished even and smooth without using extra cement with existing slope with V shaped groves 6mm wide and 10mm deep @ 0.60 metre spacing both bays or part there of on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed.

S & F for in repairs Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws l complete all as specified and directed

S & F for in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 50mm bore LDPE (low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls, ceiling or in floors including taking down of old GI tubing, 40mm bore complete all as specified and directed.

Taking down carefully aluminium/copper point wiring (light,fan,socket or power) of any type complete including fittings and fixtures such as switches,ceiling roses, pendants, holders , sockets, light fittings, removing materials to store for keeping in safe custody or for taking credit and making good the disturbed surfaces of walls/ceiling/floor at various site etc, complete all as specified and directed.

Disconnecting electric connections and taking down old unserviceable MCB DBs of any type including MCBs DB/TPN DBs including mcbs of any capacity, complete all as specified and directed.

Taking down existing fan, exhaust fan re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed in and including non metallic rigid PVC concealed conduit 20 mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including one green colour cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed the of following :

One light point/bell point controlled by one way 5 Amps single pole switch

One ceiling fan/exhaust fan point controlled by one way 5 Amps single pole switch

One 5 pin 5 Amps socket outlet on same board with other switch

One 5 Pin 5 Amps socket outlet on independent board with other switch

All as per item No 201.00 above but with 2.5 Sqmm single core multi stranded PVC insulated unsheathed (FRLS) cable for 15 Amp socket outlet on independent board

Supply and fixing of switch piano type, flush button single pole, one way 5 Amps 240V, complete all as specified and directed.

Supply and fixing of switch piano flush type 15/16 amps, single pole one way 240 volts complete all as specified and directed.

Supply and fixing of socket outlet 5 Amps, 5 Pin, flush type, complete all as specified and directed.

Supply and fixing of socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all, as specified & directed.

Supply and fixing of ceiling rose,surface type bakelite 65x17.5 mm, three terminals, complete all as specified and directed.

S&F in repair LED tube light fitting in acrylic linear tube (1x18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

Supply and fixing in repair LED mirror light fitting, 10 watt, 600 mm length complete with all accessories pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing in repair LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing in repair testing and commissioning energy saving bldg sec light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66/65 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Taking down Geyser re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F water heater storage type,electric, capacity 25 litres, BEE 5 star rated, 240 volts, input 2000 KW, PUF insulated fitted with stainless inner container and cooper coil of BEE 5 star rating models, max working head of water 25 Ltrs, fixed to wall with suitable MS tower/anchor bolts,Inlet/outlet pipes incl PVC connections grouted to wall complete all as specified and directed

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep steel body with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.

M & L for Submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 Sqmm multi stranded copper conductor cable drawn through existing concealed conduit incl one run of green colour earth continuity conductor with 4 Sqmm multi stranded copper conductor cable complete all as specified and directed. Note : - Two run of single core cable, one run of earth continuity conductor shall be measured as one unit length.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' Type instantaneous tripping complete all as specified and directed.

Supply and fixing of MCB SPN 10 to 40 Amp capacity, 10KA , 'C' Type instantaneous tripping complete all as specified and directed.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door, IP-43, DB's made out of CRCA sheet steel enclosure, recessed type, factory made powder coated, 8 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.Note : MCB DB and MCB will be the same make.

M & L for earthling complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth wire protection by 15 mm dia medium grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work in any type of soil & disposal of soi, providing alternate layers of charcoal and common salt, constr of PCC earth chamber in mix 1:3:6 type C-1 with 40mm thick RCC 1:2:4 type B-1 cover with handle made out oof 8mm dia bars, watering arrangement with funnel & wire mesh, complete all as specified and directed. Note. The unit rate includes for protection pipe and GI wire 4.00 mm from top of earth plate up to 7.5 meter above ground level.

S & F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' type instantaneous for geyser & AC complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 4.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

Supply and fixing stepped type ( switch type) electronic ceiling fan regulator flush type, AC, 230 volts , complete all as specified and directed.

S&F box type LED tube light fitting in acrylic linear tube 1x 22 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube rod 22 watt.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

Supply and fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy including fan hook complete with all as specified and directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces.

S&F modular stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed.

S&F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular bell push, 6 Amp, 1 module, complete all as specified and directed

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of door bell ding dong type electric 230 volts AC , single phase, complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

Supply and fixing LED lamp 9/10 watt , 230 volts , 50 Hz, B-22 base for fixing in lamp holder and wall mounted decorative light fitting complete all as specified and directed.

Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Taking down existing fan, exhaust fan re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'B' curve complete all as specified and directed.

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size.

Taking up/down worn out/damaged/unserviceable xlpe /PVC insulated underground cable rmoured, heavy duty with aluminium conductors of any size, 1100 Volt grade from trench/duct/pole/wall/ pipes/rooftops etc. complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all as specified and directed

Supply and spread sand in trenches as sand cushioning to underground cable for protection with dry fine river sand and provide required cover after punning down 18CM will be measured and paid complete all as specified and directed.(Note: Thickness of sand cushion after punning down will be measured and paid.)

Supply and laying well burnt sub class ‘B’ bricks ( designated 75) locally available best quality, laid dry in trenches for protection of underground cable complete all as specified and directed.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

Supply and fixing tubes Medium grade GI tubing 25 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm as in soils complete all as specified and as directed.

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point as in soils complete all as specified and as directed.

Supply and fixing tubes Medium grade GI tubing 20 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

Supply & Laying in trenches galvanised steel water tubing of medium grade with all fittings such as bends, elbows, tees, unions, nipples, short pieces etc as required at site of size 20mm dia complete all as specified and directed.

MITTAL ENTERPRISES (BID ID -3492931)

VIPRABANDHU CONSTRUCTIONS (BID ID -3493266)

M/s Kishan Gopal Agarwal (BID ID -3493524)