CONSTRUCTION OF LABS UNDER PM SHRI KV PANAGARH AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R I

Amount

Surface dressing n.exc (Not exceeding) 15 cm deep and getting out soft/loose soil complete all as specified and directed

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in in soft/loose soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

All as per item No 2.00 here-in-beore but depth exc 1.5m but not exceeding 3.00 mtrs complete all as specified and directed

M&L for Hardcore using broken stone or boulders of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose complete all as specified and directed

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as in sub base of floor complete all as specified and directed

M&L for 50mm thick sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for 200mm thick Kankar or laterite,with mix of fly ash ,clinker & stone dust in the proportion of 1:3:6 ( i.e. 10% fly ash,30% clinker & 60% stone dust ) laying in layers n.exc 100mm thick ,spread, rolled and consolidated to gradient and camber required, watering ,ramming and compacted complete all as directed by Engg-in-charge .

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) as in Chajjas complete all as specified and directed

M&L for precast cement concrete Type B-1,1:2:4 (using 20mm graded crushed stone aggregates) set in cm 1:4 as in mahhole cover etc complete all as spd and as directed.

M&L for PCC (1:2:4) type B-0 as in bed blocks for hold fast including necesssary formwork complete all as specified and directed

M&L for 40 mm thick M-20 (Nominal Mix) damp proove course using 12.5mm graded stone aggregate with water proofing compound conforming to IS-2645 liquid grade as per manufacturer’s instructions with polythene film 200 micron over 85/25 grade Industrial bitumen (IS-702 : 1988) @ 1.5 kg/sqm blended with the dry sand @ 0.05 cubic meter/ sqm.including necessary formwork complete all as specified and directed

M&L for type B-1 1:2:4 (20mm graded stone aggregate) providing RCC precast cement concrete as in cover slab for man hole and similar article with plain face set in cement mortar 1:6.

M&L for Cement concrete 1:3:6, type C-1(using 20mm graded stone aggregate) in surface channels and drains and Manholes and mass concrete complete all as specified and directed.

M&L for Extra for forming 40 cm inner girth fair finished drains or channels i.e. exc 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for brickwork with fly ash old size bricks straight or curved on plan to any radius built in CM (1:4) for mahhole complete all as specified and directed

M&L for brickwork with fly ash sub class'B' bricks straight or curved on plan to any radius built in CM (1:6) complete all as specified and directed

M&L for brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n.exc 10cm girth complete all as specified and directed

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

All as per Item No 30.00 here-in-beore but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed

M&L for TMT mild steel bars 6mm to 8mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to complete all as specified and directed

S&F mild steel as Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc complete all as specified and directed

S&F wind ties for roof including securing bolts, flat iron fillets(for securing weather boarding with screw bolts and nuts) includingall necessary drilling or riveting etc and similar work fonforming to Fe 410-O or Fe-310-O including painted with one soap coat of zinc cromate primer paint (including prepration of surfaces at contractor's workshop before fabrication) complete all as specified and directed

S&F MS flat iron as in hold fast clamps small articles conforming to FE-290 Gde-E-165 complete all as specified and directed

S&F of Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F of Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed

M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specifiedat any height including all necessary scaffolding and safety measures complete all as specified and directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, locking arrangement ,C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surfaces of concrete complete all as specified and directed

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) for fair finsihed surfaces complete all as specified and directed

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to chullah hoods, chajjas, troughs and similar items including edges for fair finsihed surfaces complete all as specified and directed

M&L for Rendering 15 mm thick cement plaster in CM (1:4) on fair faces of brick/concrete surfaces finished fair and even with using water proofing compound admixture as per manufacturer's instruction, complete all as specified and directed Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for rendering 15 mm thick in CM (1:6) on other fair faces of brick work surfaces finished fair and even complete all as specified and directed

M&L for Rendering 10 mm thick cement plaster in CM (1:6) on other than fair faces of brick/concrete work surfaces finished fair and even complete all as specified and directed..

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar (1:3) finished fair and even complete all as specified and directed.

M&L for 25 mm thick average PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in padding concrete on roof all as directed by Engineer- in-Charge.

M&L for screed bed 15mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:3 finished even and fair on roof slab including using water proofing compound admixture as per manufacturer's instructions, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule. complete all as spd and directed.

M&L for laying APP based polymeric membrane minimum weighing 3.5Kg/sqm and mimimum 3mm thick reinforced with polyster non woven fabric (weighing. not less than 160 gms/sqm) laid over and including one coat of cold bitimenous primer @0.40ltr/Sqm bitumen primer shall be of same membrane manufacturer of density at 25°C, 0.87 to 0.89 kg / Liter and viscosity 70-160 cps), by torch application complete all as specified and direcetd. The overlaps shall be minimum 100 mm on the transverse direction and 75mm on longitudinal direction complete all as specified and directed.

M&L for one coat of aluminium paint over APP membrane complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed

M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed

Material & Labour for preparation of new surfaces of plastered walls and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (2.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L for preparation of new plastered surface of wall applying of two coats of cement base paint over a coat of white wash complete all as specified and directed

M&L two coats synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement, incl making joints 10mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with and incl bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8, type D2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4, type B2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for Cement concrete 75 mm thick type B- 1, 1:2:4 (20 mm graded aggregate) laid on concrete floors and pavings; laid over cement concrete subfloors etc. and finished to an even and rough surface with nominal reinforcement, complete all as specified and as directed by Engg-in-charge. (Note: Reinforcement will be measured and paid separately)

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor for levelling course complete all as specified and directed by Egineer-in-Charge.

M&L for Non-skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed or bedding layer of 15 mm thick with cement mortar (1:6) and pointed in white or coloured cement to match.

M&L for light shade vitrified ceramic tiles 10mm thick (square) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed flush in white or colour cement with pigment over and including 15mm thick cement mortar (1:6) screed bed complete all as specified.

M&L for Glazed ceramic tiles Coloured 350 x 250mm/450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM (1:4) on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

M&L for Marble work 18mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick, laid over and including 20mm thick screed bed in cement mortar 1:4 base, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing & polishing until mirror finish, complete all as specified and as directed. Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

M&L for kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item over 10mm thick in cement mortar CM (1:3) complete all as specified and directed

M&L for 16mm to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed CM(1:6) including rounding to edges of stone complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver coloured block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed

S&F for Vitreous China white glazed fine clay laboratory sink, size 600x450mmx200mm including beding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe including brackets complete all as specified and directed

S&F Vitreous china wash down water closet pan, Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device all as specified and directed.

S&F water closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturb surface with existing finish of floor all as specified & directed by Engineer-in-Charge.

S&F 10 Ltr PVC valveless, syphonicaction type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

Supply only Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern etc complete all as specified and directed

S&F vitreous china wash basin, white, flat back, size, 550X400mm including bracket for fixing 32 mm waste coupling, waste pipe etc complete all as specifid and direted.

S&F Bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed

S&F Pillar taps, 15mm bore, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long scrwed shanks and fly-nuts, screwed for iron pipe or for connection pipe complete all as specified and directed.

S&F CP health faucet with 1.50mtr long tube & hook with necessary all fixig arreangements to fix GI water pipe connections complete all as specified and directed by Engr-in-charge

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including connections to flushing pipe and outgoing pipes fixed in repairs complete all as specified and directed.

S&F 32 mm bore Waste coupling of PTMT (half or full threaded) suitable for urinal (Minimum weight 32mm45gms/40mm-60 gms) complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F PVC flexible urinal waste pipe 1/2 inch dia fixed to urinal stall waste coupling complete all as specified and directed

S&F CP tubular towel rail 20mm dia D type 60cm between two flange including bracket complete all as specified and directed by Engr -in-Charge

S&F PVC connection 15 mm size PTMT nuts of length ength 600 mm complete all as specified and directed

S&F 15 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F 20 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F for 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per Item No 91.00 here-in-beore but 25 mm outer dia complete all as specified and directed

S&F 15mm bore fancy type stop valve/angle valve , chromium plated copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F PVC waste pipe 40mm dia for sink 01 mtr to 3 mtr as per requirement basis complete all as specified and directed

S&F CP grating with hole circular 150 mm size complete all as specified and directed

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall,laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR pipes 110mm bore single socketed in any length with rubber ring joint, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F PVC SWR bends of 110 mm bore complete all as specified and directed

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed

S&F PVC (SWR) floor trap 100mm dia of outlet plain with grating including jointing with solvent cement complete all as specified and directed

Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as spd and directed.

Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed.

M&L for laying Reinforced concrete pipes 150 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5 mm wood grain printed PVC shee twith mild steel square tube complete as per manufacturer specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and botttom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification ,drawing complete all as specified and directed by Engineer-in-Charge.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately)

S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately)

S&F 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3 as in moduler shutters/cabimet drawer cupboard cabinet shutter including all frame work as specified and directed by Engr-in-Charge

S&F Auto Closing Clip-on Soft Close Hinges with Mounting Plate (Eccentric) (L Bihari ) Engineer-in-Charge. Make ; Hettich/Ozone/Godrej

S&F magnetic catches with ferrite magnet Engineer-in-Charge. Make: Hettich/Ozone/Godrej

S&F in repairs soft close telescopic channel of size 550mm suitable for load capacity of 35 Kg. Make ; Hettich/Ozone/Godrej

S&F Stainless Steel Pull Handles (SS Grade-304) 200mm long H type, 22mm dia. Make ; Hettich/Ozone/Godrej

M&L for 4mm thick ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame work complete all as specified and directed

S&F for 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as spd and directed by Engr-In-Charge .

S&F for sheet glass 5.5 mm thick ordinary quality and glazing with rubber gasket and pin in square n.exc 0.50 sqm in each pan complete all as specified and directed

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or rubber & aluminium beading in square n. exc 0.5 Sqm in each pane, complete all as specified and directed.

S&F 100mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed

S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted.

S&F for 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed

S&F for harrison curtain rails, mild steel, chromium plated with conical end balls suitable for fixing as end of curtain/dropery rods complete all as specified and directed

M&L for aluminium snake guard fixed in aluminium doors complete all as specified and directed

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified and directed

S&F Anodised powder coated aluminium snap grid frame work for false ceiling (size of grid 605x605 mm) complete all as specified and directed

S&F Non asbestos fibre cement designer building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified and directed

M&L for 150mm bore, HDPE double wall corrugated(DWC) SN-8 PIPE (HDPE Black Pipe) WITH COUPLER Conforming to IS:16098 Part-II:2013 sewage pipes laid in trenches and jointed as per manufacturer,s instruction with and including all fitting complete all as specified and as directed.

E/M PORTION M&L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets for the following:- Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per Item No. 136.00 here-in-before but for one socket point of 3 pin 5 Amps on same board complete all as specified and directed

All as per Item No. 136.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.50 Sqmm for one socket point of 3 pin 5 Amps on same board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 2.50 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per Item No. 136.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.50 Sqmm for one socket point of 3 pin 5 Amps/15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 2.50 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per Item No. 136.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for sheet metal enclosure 20 Amp two pin and earth on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete (excluding sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover) all as specified and directed.

Material & Labour for point wiring complete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 20mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one light/fan/ bell point controlled by one switch including pressed steel terminal box powder coated of suitable size with 3 mm thick plastic laminated sheet cover of approved make for housing/mounting switches, sockets & regulators etc. and drawing 1.5 sq. mm copper solid conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-Charge Note :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 141.00 here-in-beore 5 Amp socket on Independent board with other switches complete all as specified and directed.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed By Engr-in-Charge.

S&F socket outlet 2 in 1 multipurpose 5 pin , (6 Amps ) flush type complete all as specified and directed By Engr-in-Charge

S&F switch socket combination 2 in 1 multipurpose 5 pin, (6 Amps) flush type complete all as specified and directed.

S&F switch socket combination multipurpose 5 pin, (6/16 Amps ) flush type complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings complete all as specified and directed.

S&F sheet metal enclosure with 20 Amp MCB and two pin and earth plug and socket complete with one single pole MCB all as specified By Engr-in-Charge.

S&F for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 6.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) runs of line conductor, one run of earth continuity conductor, one run of PVC conduit and one run of cutting chases shall be measured as unit length. (ii) Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per BOQ Srl Item No 150.00 here-in-before but with two run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) and one run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour)

All as per BOQ Srl Item No 150.00 here-in-before but with two run of 10.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) and one run of 10.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour)

S&F BLDC Without remote Ceiling fan of capacity 1200 mm, 240 volts, ISI mark, BEE rated 5 star, service value greater than or equal to 6 complete all as specified and directed.

S&F exhaust ventilation fan with louvers of sweep 300mm, 230 volts 1200 Rpm, with blade and frame and loures sturdy engineering plastic complete with, ISI marked complete all as directed by Engr-in-Charge.

S&F exhaust ventilation fan with louvers of sweep 300mm,230 volts, with blade and frame and loures steel body,ISI marked complete all as directed by Engr-in-Charge.

S&F 10 W LED light fitting mirror type 2',220volt AC lighting fixture with complete all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete, complete all as specified and directed.

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 25000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F 63 Amp MCCB 4 pole, 3 phase, 415 volt of capacity Amp, 16 KA complete with proper copper thimbles, copper reducer etc complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 12 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 4 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SPN 32 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Material and labour for earthing complete with copper earth plate electrode 600x600x3 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to copper strip 20 x 3mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 32 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protection GI pipe and watering pipe including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of earth lead including protection pipe, from top of earth plate upto 7.5 meter, above/below ground level is deemed to be included in the unit rate. 4. All the joints in earth lead and connection with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 2 core 10 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 4 core 25 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs, clamps, nut & bolts etc all as specified

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed. (Note : Punned thickness shall be measured).

M&L for burnt clay fly ash bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

S&F GI Light grade 50 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and directed.

S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and directed.

Jaibalaji Enterprise (BID ID -3174719)

ANSH CONSTRUCTION (BID ID -3174366)

MAHAJAN ENTERPRISE (BID ID -3175073)

KAZI SAHABUL ALAM (BID ID -3174330)

UNITED BUILDERS (BID ID -3174306)

BISWAS ENTERPRISE (BID ID -3172215)