CA NO GE/C-43/2020-21 INTERNAL PERIODICALS MISC B/R MAINT WORKS OF SANJAY VIHAR OTHER ADJOINING UNTIS AND PETTY B/R OF SANJAY VIHAR 5 SIGNAL GP 500 (I) SIGNAL COY AND OTHER ADJOINING AREAS OF AGE B/R-II (CENTRAL) DELHI CANTT-10

Amount

Checking the leakage and petty repairs to bib taps, Pillar taps, Stop cock, Concealed stop cock, angle valves, gate valves etc of any description or size for stopping leakage of water by changing washers or tightening or moving, etc complete all as specified and directed by Engineer -in Charge Note:- for Ser No 1 to 5: 1. Note : Fixtures/Fittings required to complete the job shall be paid under relevant item against supply only and rates quoted by the contractor are deemed to inclusive of necessary tools and plants incl mtrls of Dhaga/ safeda/M seal/Taflon tape/solvent/ screws/white cement/Nails,Screws/Gitties etc. 2. The complaints to be rectified within four hours on same day. The Delay in rectification of complaint more than four hours, the penality will be levied @ Rs.100.00 Per complaint. 3. Serally numbered docket booklet shall be provided by contractor without any extra cost. 4. In case of any urgent nature plumbing complete after 1700 hrs same shall also be attended to and nothing extra shall be admisible on this account.

Repairs to low level flushing cistern, syphon, washers, handles, float valves, stopping leakage of Down pipe by applying m-seal and other related works and to make the flushing cistern functional complete all as specified and directed by Engineer -in Charge.

Removal of air lock, blockage of water pipes from OHT tanks to supply point and repairs/adjustment to float valves, applying of M-seal in tanks and all other connected works of water supply from Over head water storage tanks / PVC tanks all as specified and directed.

Petty repairs to joinerys works, such as easing/adjusting of door, repairs of wire mesh, cub board shutters, iron mongerys, false ceiling works of any type or description and any type of carpentery works etc Easing of window shutters/CB shutters (One unit shall comprise of one window/CB/Showcase irrespective of number of leaves) for properly closing/opening , tightening of hinges or changing the position of hinges, adjustement of tower bolts sliding bolt etc complete all as specified and directed by Engineer -in Charge

Petty repairs to plaster, floor, plinth etc and like by PCC 1:2:4 Type B0 and plaster in CM 1:4 incl preparing roungening and cleaning the surface, and neat cement slurry as required making good, finishing even and smooth without using extra cement in patches area n exc 0.50 Sqm each patch and removal of rubbish off the premises complete all as specified and as directed.. Note : The rate quoted by the contractors is deemed to include the necessary tools and plants, screws, nails etc complete all as specified and directed by Engineer -in Charge. Note : The rate quorted by the contractor is deemed to include the necessary tools and plants, cement, sand, aggregate etc.

Supply only PVC flush pipe of 32mm dia pipe with two Nos brass check nuts for connecting low level flushing cistern to EWC/IWC complete all as specified and directed by Engineer -in Charge

supply only 10 ltrs capacity PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, Aluminium brackets for bottom support fixing with gutties embeded in wall with drilling machine etccomplete all as specified and directed by Engineer -in Charge

S & F in repairs viterous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap including making connection to flushing cistern, flushing pipe and jointing socket of flushing rim ( with and including rubber cone joint anti syphonage pipe joint to socket or stopper if anti syphonage pipe is not required and flushing rim connecton to nozzle pattern if require fixing of seat cover for pedestal pattern etc and making good the disturbed surface to match with the existingcomplete all as specified and directed by Engineer -in Charge

S&F in repairs vitreous china squatting pan (Orissa pattern) long pan including provision of cement concrete bedding for setting the trap/pan ( 1 cement 2 sand or surkhi and 5 aggregate minimum 150mm thick) alround and finished just below level of rim of pan to receive the floor finishing including fixing/connecting to component, Low level cistern, flushing pipe etc of size 580x440mm white with intergral footrest 'P' or 'S' trap front or back inlet complete all as specified (excluding flushing cistern and flush pipe ).

S&F in repairs vitreous china wash hand basin, white flat back of size 550mmx400mm (excluding taps,) but including porcelain stopper and a pair of MS bracket, CP Waste 32mm dia waste pipe, chain and plug etc complete all as specified and directed by Engineer -in Charge

Supply only plastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging devicecomplete all as specified and directed by Engineer -in Charge

Supply only mild steel chromium plated hinging device for EWC complete all as specified and directed by Engineer -in Charge

Supply only Health faucet, CP brass with 1.50 m long flexible pipe 15 mm bore of pipe screwed for iron pipe fancy pipe including two way angle cock complete all as specified and directed by Engineer -in Charge

Supply only stainless steel toilet paper holder with gitties and steel screws on walls complete all as specified and directed by Engineer -in Charge

M & L for hacking out cement joints or burning out lead joints and collecting useful materials and removing them to stores and Jointing cast iron pipes and fittings or PVC pipes and fittings, in repairs, with cement/chemical adhsives joints of upto 150mm bore pipes complete all as specified and directed by Engineer -in Charge

S & F in repairs 100 mm cast iron sanitary connection socket to fit WC out-let including taking down old one without damaging WC complete all as specified and directed by Engineer -in Charge

Supply only 32mm bore and 75cm long PVC waste pipe for WHB complete all as specified and directed by Engineer -in Charge

Supply only 40mm bore and 75cm long PVC waste pipe for Kitchen sink complete all as specified and directed by Engineer -in Charge

Supply only PVC connection 375 mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer ccomplete all as specified and directed by Engineer -in Charge

All as per item No.22 above but 450mm long complete all as specified and directed by Engineer -in Charge

All as per item No.22 above but 600mm long complete all as specified and directed by Engineer -in Charge

Supply only 15 mm dia brass chromium plated pillar tap with fly nuts capastan head screwed down high pressure with or without lettered hot or cold with long scewed shank complete all as specified and directed by Engineer -in Charge

Supply only MS bracket for kitchen sink/Wash hand basin including necessary nut and bolts , painting on brackets etc as per existing one at site complete all as specified and directed by Engineer -in Charge

Supply only 15mm dia Brass CP mixer for wash hand basin, mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer -in Charge

Supply only 15mm dia Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer -in Charge

Supply only brass spindle/phase suitable for 15mm dia bib cock, stop cock, concealed stop cock, angle cock, wall mixer, basin mixture etc of any type or size complete all as specified and directed by Engineer -in Charge

Supply only stainless steel soap dish complete all as specified and directed by Engineer -in Charge

Supply only brass chromium plated bib tap for iron pipe of 15mm bore fancy type with flynut capstain head screwed for iron pipe or for brass ferule and fixed for bore/ dia of pipe in 15mm complete all as specified and directed by Engineer -in Charge

All as per item No 33 above but long body complete all as specified and directed by Engineer -in Charge

Supply only CP brass shower rose 125 mm size suitable for 15mm bore pipe complete all as specified and directed by Engineer -in Charge

Supply only stainless steel plate rack of size 90x80x25 cm depth size made out of 0.80 mm thick sheet complete all as specified and directed by Engineer -in Charge

Supply only stainless steel sink with or without drainage board made out of 0.80 mm thick sheet for kitchen with plug, washers, waste pipe incl fixing cast iron cantilever bracket connecting union over all size 1145x510mmx200mm with bowl size 510x400x200mm complete all as specified and directed by Engineer -in Charge

Supply only mild steel chromium plated grating (round) 125mm dia fixed over floor/nahani trap (with hole or without hole)complete all as specified and directed by Engineer -in Charge

Supply only chromium plated brass stop cock fancy type screwed both ends high pressure for 15mm bore size iron pipe or ferrule complete all as specified and directed by Engineer -in Charge

All as per item No 34 above but with long shank and cup (concealed type) complete all as specified and directed by Engineer -in Charge

All as per item No 34 above but angle cock complete all as specified and directed by Engineer -in Charge

Supply only stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed for 15 mm bore complete all as specified and directed by Engineer -in Charge

Supply only 15 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer -in Charge

Supply only 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer -in Charge

Supply only of 15mm bore size PTMT bib tap complete all as specified and directed by Engineer -in Charge

S&F Rotational moulded polythylene 1000 Ltr capacity water storage tank tripple layered WHITE (Cylindrical vertical with closed top )composite type or lid should be thread type) hoisted and fixed in position with 20mm dia brass float valve complete including ball valve and tank connection complete including dismantling of pvc tank complete all as specified and directed by Engineer -in Charge

All as per item No 41 above but storage capacity 500 Ltrs complete all as specified and directed by Engineer -in Charge

Supply only HDPE PVC lid (cover) for 1000/500 Ltrs capacity PVC tank complete all as specified and directed by Engineer -in Charge

Taking up and down of old steel tubing connection in new or old position (wall etc) incl cleaning for refixing or fixing new pipe, bore of pipe 15mm bore complete all as specified and directed by Engineer -in Charge

All as per item No 44 above, but 20mm bore complete all as specified and directed by Engineer -in Charge

M & L for Cutting/screwing/jointing existing steel tubing 15 mm or 20 mm bore for alterations or additions (Each cut measured) complete all as specified and directed by Engineer -in Charge

Refixing old steel tubing and connection in new or old position(walls,ceiling,floors etc.) for 15 mm bore GI complete all as specified and directed by Engineer -in Charge

Refixing old steel tubing and connection in new or old position(walls,ceiling,floors etc.) for 20 mm bore GI all as specified

M & L for GI tubing ISI marked medium grade 15mm bore with all fittings and fixed complete to walls and ceiling or laid under floor including connection etc, complete all as specified and directed by Engineer -in Charge

All as per item No 49 here in before but 20 mm bore complete all as specified and directed by Engineer -in Charge

Supply only 15 mm dia wall mixer, Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed including making good of disturbed portion on walls and tiles to match with the existing surfaces complete all as specified and directed by Engineer -in Charge

Cleaning and removing all scale and dirt, etc, from tanks of 500 to 1000 litres capacity and from mouths of circulating pipes, etc and applying bleaching powder for cleaning on tanks complete all as specified and directed by Engineer -in Charge

S&F in repairs galvanised mild steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc on 2nd class HW wooden/ fillets (15mmx15mm) or on steel or wooden windows duly painted with synthetic enamel paint complete all as specified and directed by Engineer -in Charge

Supply only brass 300 mm, ordinary rat tail rod pattern springs including roller and roller plate fixed to stone/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc.complete all as specified and directed by Engineer -in Charge

All as per item No.55 above here in before but mild steel complete all as specified and directed by Engineer -in Charge

Supply only PVC syphon (Make : super flush/parryware/hindware) complete for low level flushing cistern complete all as specified and directed by Engineer -in Charge

S & F Sheet glass, 3mm thick ordinary quality, in squares n exc 1.00 sq. m each pane glazing with oil putty or glazing clips or wooden beadings, aluminium beadings etc incl hacking out old broken glass complete all as specified and directed by Engineer -in Charge Note :- And all the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Supply only PVC mirror cabinet of size 500X400X120mm fancy type fixed with 4 Nos stain less steel clips complete all as specified and directed by Engineer -in Charge

Supply only Glass Corner Shelf 10mm thick including CP railing radius 300mm radius complete all as specified and directed by the Engineer-in-Charge.Make : Make- Hi-Life/Nixo or Equivalent.

Supply only Glass shelf assembly 450mm long 150mm wide with cp railing complete all as specified and directed by Engineer -in Charge

Supply only two legged aluminium floor door stopper with rubber shoe 140mm long complete all as specified and directed by Engineer -in Charge

Supply only mild steel barrel tower bolts, stove enamelled black with bright bolts and fixed 200 mm long bolts in repair complete all as specified and directed by Engineer -in Charge

Supply only mild steel barrel tower bolts, stove enamelled black with bright bolts and fixed 150 mm long bolts in repair complete all as specified and directed by Engineer -in Charge

Supply only MS pressed handles oval type stove enamelled black, 150 mm size as in repaircomplete all as specified and directed by Engineer -in Charge (Make-Ashish or equivilant model of make as approved by GE).

Supply only MS pressed handles oval type stove enamelled black, 100mm size as in repair complete all as specified and directed by Engineer -in Charge(Make-Ashish or equivalent make as approved by GE).

Supply only in repairs continuous (Piano hinges, mild steel bright finished or electro galvanised width of flap 30 mm when open complete all as specified and directed by Engineer -in Charge

M&L in repairs 4mm thick plywood BWR, type BB, 3 No of ply fixed with nails to timber frame work or repair works complete all as specified and directed by Engineer -in Charge

S & F in repair chicken wire mess standard thickness and aparture complete all as specified and directed by Engineer -in Charge

S & F in repairs Alumimium sheet 0.5 mm thick, fixed with aluminium alloy screws complete all as specified and directed by Engineer -in Charge

Supply only 100 mm size stainless steel hasp and staple complete all as specified and directed by Engineer -in Charge

Supply only 300 mm long aluminum alloy anodised sliding door bolt with hasp staple balt-type and fixing clips of sheet case or extruded sections and fixing bolls and sliding bolls extruded sections or case aluminum alloy complete all as specified and directed by Engineer -in Charge Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

Supply only 150mm long extruded alumiunium alloy handle fabricated type anodized (D type) complete all as specified and directed by Engineer -in Charge .Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

All as per Srl item No 82 above but 125mm long complete all as specified and directed by Engineer -in Charge.Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

Supply only 150 mm size aluminium, anodised barrel tower bolts of extruded section and fixed to shutter complete complete all as specified and directed by Engineer -in Charge Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

All as per item No.75 above but 100mm long complete all as specified and directed by Engineer -in Charge. Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

Supply only 40 mm dia cup board knob fixed with nut screw and washer of mild steel bright finish.complete all as specified and directed by Engineer -in Charge

S&F in repair 150mm long aluminium anodized hasp and staple fixed with mild screws to shutters complete all as specified and directed by Engineer -in Charge.Make :- Ashish /M/s kitch Architectural product's (P) Ltd /Mowjee all ISI Marked.

S&F Medium Density Fibre board 18/19 mm thick , exterior grade, fixed with screws to timber frame work including dismantling the boarding and providing continuous Piano hinges, bright finish stainless steel, width of flaps when open 30mm with suitable size steel screws ccomplete all as specified and directed by Engineer -in Charge

S&F Prelaminated particle board 18/19 mm thick , exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including dismantling and providing continuous Piano hinges, bright finish stainless steel, width of flaps when open 30mm with suitable size steel screws complete all as specified and directed by Engineer -in Charge

Supply only flush handle PVC with adjustable lever and hook for low level flushing cistern complete all as specified and directed by Engineer -in Charge

Repairs to steel windows by straightning, welding of damaged portions, greasing & oiling to make funcitional like easy for closing and opening etc complete all as specified and directed by Engineer -in Charge

M&L for glazed coloured ceramic tiles (300x200mm) x6 to 7mm thick in dado etc set and jointed in neat cement slurry and pointed in coloured cement to match incl 10mm thick backing coat in cm 1: 4 incl dismantling old tiles complete all as specified and directed by Engineer -in Charge

M&L for non skid coloured ceramic tiles (300x300mm) x6 to 7mm thick in floor etc set and jointed n neat cement slurry and pointed in coloured cement to match incl 15mm thick secreeding in CM 1 : 6 incl dismantling old tiles complete all as specified and directed by Engineer -in Charge

S&F in repairs glazed /non skid ceremic tiles white /coloured as per the existing tiles and size as suitable/matching with the existing tiles in dados/floors including necessary cement work/white cement painting incl dismantling old tilescomplete all as specified and directed by Engineer -in Charge ( Make : Orient/Somany/Kajaria Size: 0.06 sqm to 0.18 Sqm each)

S&F in repairs rectified/vitrified ceremic tiles white /coloured as per the existing tiles and size as suitable/matching with the existing tiles in skirtings/floors including necessary cement work/white cement painting incl dismantling old tiles complete all as specified and directed by Engineer -in Charge. ( Make : Orient/Somany/Kajaria Size: 0.18sqm to 0.36 Sqm each)

Taking down cement plaster from brick or concrete surface incl racking out joints hacking for key and scrubbing down with water complete including removal of rubbish off the premises complete all as specified and directed by Engineer -in Charge

M&L rendering 15mm thick in cement mortar 1 : 6 each on brick or conc surface of walls finishing even & smooth without using extra cement incl two coats of colour wash over one coat of white wash and preparation of surfaces complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M & L for laying 40mm average thickness PCC 1 : 2 : 4 type B1 using 20mm graded crushed stone aggregate including demilition of existing PCC and repairs, finished even and smooth incl roughning old surfaces applying cement slurry @ 3.00 Kg/Sqm etc complete incl demolition of cement concrete complete all as specified and directed by Engineer -in Charge

M & L for brick work with fly ash bricks to any radius as in half brick thick wall built in cement mortar 1 : 4 incl demolition of brickwork complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M & L for brick work with fly ash bricks straight or curved on plan exc 6 mmean radius incl demolition of old brickwork complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S&F 40mm wide 3 to 6mm thick rubber beading fixed to door shutter with nails as in repair complete all as specified and directed by Engineer -in Charge

All as per item No 101 here-in-before but 50mm wide and 6 to 3mm thick tappered complete all as specified and directed by Engineer -in Charge

Taking down old pelmet and refixing after necessary repair including clamps/picture plate n exc 1.50mtr long complete all as specified and directed by Engineer -in Charge

All as per item No 95 here-in-before but length of pelmet exc 1.50 mtr and n exc 2.00 mtr complete all as specified and directed by Engineer -in Charge

Supply only 19 to 20mm bore mild steel chromium plated curtain rod complete as in repairs complete all as specified and directed by Engineer -in Charge

Supply only curtain bracket suitable for 19mm bore curtain rod complete as in repair complete all as specified and directed by Engineer -in Charge

Supply only 300mm MS sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on stapple late complete all as specified and directed by Engineer -in Charge

Supply only 100mm size of butt hinges, medium weight cold rolled mild steel complete for door etc complete all as specified and directed by Engineer -in Charge

All as per item No 99 here-in-before but 75mm size complete all as specified and directed by Engineer -in Charge

Supply only 100mm size double action spring hinges mild steel swith steel wire spring, stove enamelled black complete all as specified and directed by Engineer -in Charge

(a) Dismantling of floor of WC with Indian type Water closet and removing out the complete cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M & L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top@Seal – 107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-1 and top coat with Sika Top® [email protected] Kg/Sqm or equivalent of Fosroc or Pidilite. (d) M & L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete Plus as specified . (e) M & L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M & L for sunken portion filled with 40mm graded brick bats and finished with 50mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 2.00 Sqm each.

S & F in repairs 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, waste and vent pipes in any length with or without ears, fixed in walls/floors/ trenches etc complete all as specified and directed by Engineer -in Charge Note : For pipes fixed on walls to be suitably clamped using stack clamps (rates inclusive in this item) of appropriate size @ 1 m apart for height of pipe) and all the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, waste and vent pipes in any length with or without ears, fixed in walls/floors/ trenches etc complete all as specified and directed by Engineer -in Charge Note : For pipes fixed on walls to be suitably clamped using stack clamps (rates inclusive in this item) of appropriate size @ 1 m apart for height of pipe) and all the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs PVC (SWR) bends 110 mm dia complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs PVC (SWR) bends 75 mm dia complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs 100 mm dia cast iron (spun pipe) soil, waste and vent pipes in any length with or without ears, with cement joints, fixed in walls/floors/trenches etc complete all as specified and directed by Engineer -in Charge Note : For pipes fixed on walls to be suitably clamped using stack clamps (rates inclusive in this item) of appropriate size @ 1 m apart for height of pipe) and all the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs 75 mm dia cast iron (spun pipe) soil, waste and vent pipes in any length with or without ears, with cement joints, fixed in walls/floors/trenches etc complete all as specified and directed by Engineer -in Charge Note : For pipes fixed on walls to be suitably clamped using stack clamps (rates inclusive in this item) of appropriate size @ 1 m apart for height of pipe) and all the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs Cast iron Bends of 100mm dia (any radius), diminishing pieces or tapers (larger bore measured) etc complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

S & F in repairs cast iron Bends of 75mm dia (any radius), diminishing pieces or tapers (larger bore measured) etc complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Supply only Aluminum drapery Rod 25mm dia incl side caps and wooden brackets, wooden Rings @ 12cm c/c complete all as specified and directed by Engineer -in Charge

M&L for 35 mm thick 2nd class hard wood glazed and Skelton door shutter, factory made, open rebated and prepared to receive glass/gauge etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitered beads for securing glass/gauge etc size of member as specified in SSR Part I Section 8 clause 24(a) and fixed to chowkat(incl two nos 150 mm long extruded aluminium tower bolts, three nos 100mm long medium weight MS butt hinges, two nos 150 mm long extruded aluminium handles, one stopper and two nos 300 mm long Aluminum Sliding door bolts and two coats synthetic enamel paint along with one coat of pink primer) incl taking out and removal of old shutter complete all as specified and directed by Engineer -in Charge

S& F 35 mm thick flush shutters (factory made) solid core construction, with block board core and plywood face panel, commercial type on both sides. Flush shutters shall have teak wood edging as specified in IS (incl two nos 150 mm long extruded aluminium tower bolts, three nos 100mm long medium weight MS butt hinges, two nos 150 mm long extruded aluminium handles, one stopper and two nos 300 mm long Aluminum Sliding door bolts and two coats synthetic enamel paint along with one coat of pink primer), incl taking out and removal of old shutter complete all as specified and directed by Engr-in-Charge

S&F Factory made solid panel PVC door shutter30 mm thick (style) consisting of ramemade out of M.S. tubes for top & bottomrails. M.S. frame shall be covered with heatmoulded plain colour PVC ‘C’ channelhaving a PVC sheet strip of 20mm widthstuck inside with solvent cement for stilesand plain colour PVC sheets for top rail,lock rail & bottom rail on either side & asgap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to befitted in the M.S. frame welded / sealed tothe stiles & rails with suitable PVC sheetbeading, and joined together with solventcement, suppling & fixing in the frame at site as per specification & drawing incl taking out and removal of old shutter complete all as specified and as directed by Engineer-in-Charge

M&L removing existing old treatment from walls using mechanical grinder complete all as specified and directed. Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M& L for applying a uniform thickness (average 2-3 mm thickness) of cement based wall care putty of approved make ( birla/ JK ) to the entire surface of walls surfaces finished even and smooth complete all as specified and directed by Engineer -in Charge Make of putty : Birla wall care /JK wall care Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M& L for applying two coats of Oil Bound Distemper on wall surfaces using roller brush to give an even and smooth surface having no sign of brush marks complete all as specified and directed by Engineer -in Charge. Make :- Asian paints (Royale)/NerolacPaints/ Berger (Rangoli) Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for rendering 15mm thick on fair faces of brick or concrete in CM (1:6) even and smooth as in walls without using extra cement, complete all as specified and directed by Enginer in Charge. Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M& L for preparing newly plastered surfaces and applying two coats of Oil Bound Distemper using roller brush over 2mm wall care putty and a coat of alkali resistant primer to give an even and smooth surface having no sign of brush marks complete all as specified and directed by Engineer -in Charge. Make :- Asian paints (Royale)/NerolacPaints/ Berger (Rangoli) Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for rendering 15mm thick on fair faces of brick or concrete in CM (1:4) even and smooth as in walls without using extra cement, complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Material and labour for preparation of new plastered surfaces as of walls and applying Two coats of weather proofing exterior acrylic emulsion paint of DULUXWeather shield Max or APEX ULTIMA from Asian paint over 2mm wall carte putty and one coat of primer from the same manufacturer complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for 5mm thick rendering in cement mortar 1:3 finished even and smoothe surface without using extra cement on ceiling, chajja in double storey building etc complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white lime wash 01 coaot of primer complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for preparation of old surfaces of walls and applying two coat of cement based paint using roller brush complete all as specified and directed by Engineer -in Charge. Make :- SNOWCEM/DUROCEM/ASIAN PAINTS/BERGER PAINTS. Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Complete removal exising old surfaces of wall / ceiling by scrubbing with hard brushing ,brooming down or steel wire brushing scraping down smook root mould moss and efforescent salts and treating oil and greasy spots as applicable and washing with water and applying cement based wall care putty of approved make 1mm thick (average thickness) unifomly and applying Two coats of weather proofing exterior acrylic emulsion paint of DULUXWeather shield Max or APEX ULTIMA from Asian paint over one coat of primer from the same manufacturer complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Preparation of old decorated surface (plastered or unplastered) of ceiling incl cornices pillar etc by brooming down or steel wire brushing, scraping down smoke root mould moss and efforesceent salts and treating oil and greasy spots as applicable and applying one coat of white lime wash on ceiling surfaces complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Preparation of old decorated surface (plastered or unplastered) of walls incl cornices pillar etc by brooming down or steel wire brushing, scraping down smoke root mould moss and efforesceent salts and treating oil and greasy spots as applicable and applying two coat of white lime wash on walls surfaces complete all as specified and directed by Engineer -in Charge Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for Preparation of old painted surfaces of wood based surfaces of any description over 10 cms width or girth using paint brush by applying sand paper etc.for proper preparation and applying one coat of synthetic enamel paint brush complete all as specified and directed by Engineer -in Charge.Make of paint:- Asian paints/Berger/Nerolac Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

All as per item No 137 above but applying two coats of synthetic enamel paint complete all as specified and directed by Engineer -in Charge. Make of paint:- Asian paints/Berger/Nerolac Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

M&L for Preparation of old painted surfaces of steel of any description over 10 cms width or girth by using sand paper etc.for proper preparation and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer -in Charge Make of paint:- Asian paints/Berger/Nerolac Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

All as per item No 130 above but applying two coats of synthetic enamel paint complete all as specified and directed by Engineer -in Charge Make of paint:- Asian paints/Berger/Nerolac Note :- All the necessary scaffolding, padding, trestles required for carrying out work should be borne by the contractor in this item only and nothing extra should be paid to contractor for height of building upto G+5

Removal of false ceiling boards for checking out leakage complaints and then refixing the same in position including repair to angles, cleats and other sections of false ceiling complete all as specified and directed by Engineer -in Charge

Material and labour in repair false ceiling using plain galvanised steel ceiling system consisting of 600 mmx600mm tiles of precoated galvanised steel sheet in 0.5 mm thick in white or coloured to be laid on grid system with 15 mm wide T section flanges having rotary stitching on the main runner and 1200 mm cross tees.The main runner spaced 1200 mm centre to centre flush fitting 1200 mm long cross tees to be interlocked between runner at 600mm centre to form 1200x600 mmmodule .Perimeter trim to be wall angle of size 3000x19x19 mm secured to wall @450 mm centre to centre and including suspension system as per manufacturer instructions complete all as specified and directed by Eingineer in charge . Make-ARMSTRONG Model No ANF W8672 or Equivalent as approved by GE .

M & L for 16-18 mm thick Black Granite stone work (table rubbed and polished) over and including15mm thick Screed bed or bedding layer in CM 1:4, as in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite,front and side of slab moulded and polished including dismantling the existing stone slab with screed/ backing and removal of debries out side the MOD Land complete all as specified and as directed by the Engineer-in-Charge.Note- The cost of making hole for Gas pipe in cooking plateform is included in unit cost of item and nothing extra shall be paid on this account complete all as specified and directed by Engineer -in Charge.

M&L Cleaning and removing all marks of OBD and enamel paint and thereafter washing the floor with clean water to maintain the hygeine including removing the dust/marks and cleaning of furniture and laying it out properly at the respective location complete all as specified and directed by Engr-in-Charge.

Cutting shrubs wid growth plants not exc 30 mm girth grown on permanent structures of roofs, wall shafts, coloumns, beams and removign same right from roots and further growth. Applicantion shall be as per manufactureres instruction. The disturbed area shall be repaired with PCC (1:2:4) Type B-0 mix and surface finished even and smooth in 1:4 including applying two coats of matching finish i.e. OBX/exterior acrylic emulsion paitn of same shade & finish. Likely minimum number of shrub/plants in each building is not less than 50 nos. Work in high rise building upto six storied. Complete all as specified and directed by Engr-in-Charge.

Note :- Total amount of Sch of credit is Rs.83740.00 as per Sch of credit. Net contract sum shall be total quoted amount of bidder (-) amount of Sch of credit.

M/S CHANDER MUNI

imran construction company

POONAM ENTERPRISES

GIAN ENGINEERS

M/S Sunil Steel Works

JAIPAL AND BROTHERS