SPECIAL REPAIRS TO BLDG No. KHY-107 (04 x OR MARRIED ACCN) OF MH SHIMLA AT JUTOGH CANTT UNDER GE JUTOGH

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below/above ground level), complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish removed outside the defence land complete all as specified.

Taking down cement plaster on brick or stone wall surfaces, etc including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified.

Rendering 15 mm thick on other than fair surfaces of brickwork or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement using WPC complete all as specified. (Note : Supply only WPC will be measured and paid separately under relevant item.

5 mm thick rendering in cement mortar 1:4 on ceiling surface finished even and smooth without using extra cement complete all as specified.

Cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregated) as in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throttling, as directing including necessary form work complete all as specified.

Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified

Glazed ceramic coloured tiles 350x250x7mm / 450 mm x 300 mm x 6 to 7 mm thick,as in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4) complete all as specified.

25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for floors complete all as specified.

Non skid ceramic coloured tiles joint free 7-8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed with cement mortar 1:6 complete all as specified

Non skid ceramic coloured tiles joint free 7-8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm , in skirting/dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick rendering in CM (1:4) complete all as specified.

Complete removal of existing treatment on old surface of walls and applying two coats of weather proof exterior acrylic emulsion paint on external surfaces over a coat of alkali resistant primer complete all as specified.

Preparing plastered or unplastered new surface of walls and applying two coats of weather proof exterior acrylic emulsion paint on external surfaces over a coat of alkali resistant primer complete all as specified.

Complete removal of existing treatment of ceiling and applying two coats of white wash on old surface of ceiling including preparation of plastered surface complete all as specified.

Applying three coats of white wash on new surface of ceiling including preparation of new plastered surface of ceiling complete all as specified.

Preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of primer over and including 3 mm thick white cement based wall care putty complete all as specified.

Complete removal of existing treatment of walls including preparation of surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer over and including 3 mm thick white cement based wall care putty complete all as specified.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified.

75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified.

Coloured chequered rubber finished cement concrete tiles 30 cm x 30 cm x 20 mm thick with grey cement and pigment, over and including 20mm thick screed bed in CM (1:6) set jointed and pointed in neat cement slurry in floors complete all as specified.

Sand cushion filling under floors or in foundations including watering and consolidation complete all as specified.

Machine pressed precast concrete interlocking paver block 60mm thick (using M-40 Grade design mix concrete) with grey cement and pigment of any size and shape conforming to IS 15658-2006 etc complete all as specified.

15 mm bib taps fancy type cast copper alloy with crutch with butter fly handle, screwed for iron pipe or brass ferrule, fixed in repair complete all as specified.

15 mm dia stop valves cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed in repair complete all as specified.

Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe fixed in repair complete all as specified.

Chromium plated shower rose, any size with or without swivel joints, including fixing to steel pipe or union complete all as specified.

Viteous China squatting pan, Orissa, pattern, size 580 x 440 mm white with integral foot rest fixed in repair (excluding flushing cistern and flush pipe) complete all as specified.

10 litres cap PVC low level valveless syphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and flushing pipe, fixed in repair complete all as specified.

Vitreous china wash basin, white, flat back, size 550 x 400 mm including bracket, waste fitting with pipe fixed in repair to wall complete all as specified.

Cast iron floor trap 100 mm dia with SS grating including jointing to waste pipe in cement concrete type 1:2:4 type B-1 fixed in repair complete all as specified.

15 mm pillar tap fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot; or 'cold' with long screwed shanks and fly nut, screwed for iron pipe and fixed, complete all as specified.

15mm dia stop cock,cast copper alloy fancy type, chromium plated,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions fixed in repair complete all as specified.

Sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling, waste pipe; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm fixed in repair complete all as specified.

Stainless steel plate rack of size not less than 600 x 750mm with 250mm depth for kitchen made of 1mm thick sheet of best quality with suitable hanging arrangement and fixed in repair to wall complete all as specified. Note :- Weight of plate rack shall not be less than 6 Kg each.

Towel rail 600 mm long brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) complete all as specified.

PVC connection 450mm long and 15 mm dia with brass fly nut at both ends complete all as specified.

Taking up or down steel tubing and connections 15 mm bore complete all as specified.

Taking up or down steel tubing and connections 20 mm bore complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified.

15 mm mild steel galvanised tubing medium grade ISI marked with all fittings such as bends, elbows, tees, short pieces, connections, backnuts, diminishing pieces, caps, plugs and unions etc and fixing with wall hooks, wooden plugs etc and cutting, screwing and waste including cutting through walls, floors etc and making good the disturbed surfaces complete to wall and ceilings or laid in floors complete all as specified.

20 mm mild steel galvanised tubing medium grade ISI marked with all fittings such as bends, elbows, tees, short pieces, connections, backnuts, diminishing pieces, caps, plugs and unions etc and fixing with wall hooks, wooden plugs etc and cutting, screwing and waste including cutting through walls, floors etc and making good the disturbed surfaces complete to wall and ceilings or laid in floors complete all as specified.

Fixing only old steel tubing and connections 15 mm bore, in new or old position (walls, ceiling, floors, etc) complete all as specified. Note : GI pipe obtained from taking down shall be used).

Fixing only old steel tubing and connections 20 mm bore, in new or old position (walls, ceiling, floors, etc) complete all as specified. Note : GI pipe obtained from taking down shall be used).

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Steel ventilators, with top hung shutter including hinges steel peg stay, complete all as specified and directed.

Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm fitted with tinned tacks or galvanised wire staples complete all as specified.

Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm fitted with tinned tacks or galvanised wire staples fixed in repair complete all as specified.

Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

Sheet glass ordinary quality 3mm thick glazing in square/ rectangle n,exc 0.50 sqm each pane with oil putty or aluminium beads fixed to steel etc complete all as specified and directed.

Figured glass ordinary quality 3mm thick glazing in square/ rectangle n,exc 0.50 sqm each pane with oil putty or aluminium beads fixed to steel etc complete all as specified and directed.

Welded mild steel wire fabric not exceeding 4.00 kg/sqm to wood or steel members complete all as specified and directed.

Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors ; ladders ; framed balusters; walk ways ; raillings; framework of watertanks and similar work conforming to Fe-290. Gde-E-165. complete all as specified.

Dismantling water tanks or capacity exceeding 500 ltrs and not exceeding 1000 ltrs, complete all as specified

Rotational moulded polyethylene water storage tanks (cylindrical vertical type with closed top) of 1000 litres capacity, ISI marked,Three layered, marked embossed, hoisted and fixed in position including connecting up pipes complete all as specified.

20 mm ball valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or ferrule and fixed, complete all as specified.

Galvanised mild steel pan mortar (Tasla) 21-22 inch dia not less than 1mm thick with 04 Nos bolt of 5-6mm dia, with 8 Nos nut bolt including fixing on water storage tank as tank cover complete all as specified.

Gun-metal, globe or gate valves 20 mm bore, with iron wheel head, screwed both ends for iron pipes , and fixed to 20mm dia of pipe complete all as specified.

Taking down Chowkats or Frame with shutter, n exc. 1.50 Sqm Each (without Taking Off Shutters from the Frame) ,including making good disturbed surface complete all as specified.

Taking down Chowkhats or frames exc. 1.5 sq. m but n.exc 4 sqm each with shutter (without taking off shutters from the frames) and removing to store complete all as specified.

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each and refixing in the same opening after repairs complete all as specified.

2nd class hardwood plain solid straight chowkat and frames wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joint all as specified.

35 mm thick 2nd class hard wood glazed and skeleton shutter open rebated and prepared to receive glass gauze etc (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Pt I Section 8, clause 8.2 (a) complete all as specified.

35mm thick IInd class hard wood plain framed, panelled shutters (any numbers of panels), with panels of timbers flat on bith sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

Block board 18/19 mm thick, grade 1 quality, 'exterior grade', decorative type with decorative face veneer on one face, fixed with nails/ screws sin cup board shutter/ pelmets etc. or to timber frame work, fixed in repairs including 6mm thick teak wood lipping complete all as specified.

Hasp and staple of 100 mm size safety type,of aluminium anodised including bolt to hinge plate and fixed with screws ,complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified.

Mild steel 300mm ordinary rat rail pattern springs including roller and roller plate fixed in repairs complete all as specified.

Butt hinges 100 mm size medium weight, cold rolled mild steel and fixed complete all as specified and directed.

Butt hinges 75 mm size medium weight , cold rolled mild steel and fixed complete all as specified and directed.

Continuous piano hinges mild steel bright finish or electrogalvanized with open flap width 30 mm, fixed in repairs complete all as specified and directed.

Butt hinges medium weight, cold rolled mild steel of 50mm size complete all as specified and directed.

IInd class Hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. Cm each complete all as specified and directed.

Aluminium handles, 150 mm size, cast type, anodised complete all as specified.

200 mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified.

250 mm aluminium anodized sliding door bolts, ISI marked, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified.

Preparation of new steel surfaces of any description priming with red oxide with two coats synthetic enamel paint , over 10cm in width or girth, complete all as specified.

Preparing old steel surfaces exc 10cm width or girth for one coat of synthetic enamel painting over a coat a of red oxide primer complete all as specified.

Preparing new wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

Ditto all as above item No 83 but one coat of synthetic enamel paint on old wood or wood based surfaces complete all as specified

Demolition of stone slabs of any description or thickness in floors , aprons etc, laid bedded and pointed in any mortar complete all as specified.

Machine cut kota stone slab flooring 18-20 mm thick over 20mm thick cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engr-in-Charge

Kota stone slab18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement 10 mm thick plaster in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engr-in-Charge

Granite (of any type) 20 mm thick one side machine polished in steps, jambs, pillars, window Cills, and top of kitchen platform and top of counter top wash basin etc set and jointed in neat cement slurry and pointed with coloured cement to match shade including 20mm thick screed bed in CM 1:4 complete all as specified.

Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) including laid over 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

Rounding to edges of stone slabs one edge, such as in , cooking platform, and other similar situations all as specified and directed

Dismantling wall / Ceiling board any thickness including cover fillets complete all as specified.

4mm thick 600x600mm non asbestos fibre cement building boards (self design) fixed or laid /inserted to timber/GI/Aluminium frame work with screws in ceiling flat or sloping complete.

GI frame work of size 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified.

Hangars 6 mm dia, GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long, size of grid 605 x 605 mm and expansion hold fasteners 12.5 mm dia, 40 mm long complete all as specified

Dismantling of cast iron or reinforced concrete drain pipe of 100 mm dia, jointed in cement mortar and taking out of trenches/floor/wall if required complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipe of 75 mm dia, jointed in cement mortar and taking out of trenches/floor/wall if required complete all as specified and directed.

100 mm bore Cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

75 mm bore Cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

100 mm bore cast iron Bends with oval access door (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified

75 mm bore cast iron Bends with oval access door (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified

Branch pieces, single (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches 100 mm bore with oval access door fixed in repairs complete all as specified & directed.

Cast iron cowls of 100 mm dia fixed in repairs complete all as specified and directed.

Cast iron cowls of 75 mm dia fixed in repairs complete all as specified and directed.

Mild steel PVC coated coloured 25 mm dia drapery rods for curtains incl decorative end holders and brackets (wall to wall or flush to wall) for securing curtain rod, fixed in repair complete all as specified and directed .

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long fixed in repair complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

Rendering/screed bed or bedding layer of mortar 15mm thick in CM 1:3 with WPC (Sunken slab) complete all as specified and directed.

Preparation of plaster surfaces /RCC roof surfaces and applying one coat of bituminous primer @0.30 Ltr/sqm complete all as specified and directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including cleaning surfaces etc complete as in sunken portion complete all as specified and directed.

Cement concrete type E2, 1:5:10 (40mm graded stone aggregate) as in filling and mass aggregate complete all as specified and directed.

15mm thick cement plaster in cement mortar 1:3 on roof slab using water proofing compound as per manufacturer instruction's. Surface shall be finished even and smooth without using extra cement. (water proofing compound will be measured and paid separately).

Priming surfaces with bituminous oil based primer 0.20 ltr per sqm on clean and dry surface complete all as specified

APP based polymeric membrane minimum weighing 3.5kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torch application with overlap of 15cm and finally shall be finished with a coat of aluminium paint @ 0.2Kg/sqm as per manufacturer instruction complete all as specified and directed.

75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in Sub base , plinth protection & paving finished even & smooth without using extra cement complete all as specified and directed.

Cement concrete type B1, 1:2:4 (20 mm graded aggregate) in surface channels and drains etc including cement concrete surface even and smooth complete all as specified.

Taking down carefully aluminium point wiring (light, Socket or power) complete including fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets etc for re use to be measured separately including making good the disturbed portion/surface complete all as specified and directed.

Point wiring with colour coding multistranded copper conductor cable, PVC insulated(FRLS) and unsheathed size 1.5 sqmm with PVC concealed conduit with fixing accessories, to be fixed, for one light/fan/bell point controlled by one switch with pressed steel concealed terminal boxes covered with 3mm thick laminated sheet/modular with all fittings (ISI Marked) incl continous earth wire of PVC insulated unsheathed multi stranded copper conductor cable size 1.5 sqmm for earth wire connected to common earth dolly all as specified and directed .

All as per item No 119 above but point wiring for two way.

All as per item No 119 above but for one 3/5 pin socket 5 Amp on same board, with 1.5 sqmm wire with 1.5 sqmm earth wire .

All as per item No 119 above but for one 3/5 pin socket 5 Amp on independent board with 1.5 sqmm wire with 1.5sqmm earth wire .

All as per item No 119 above but for 3 pins socket outlet 15 Amps independent with 4 sqmm incl continous earthing with multistandred copper conductor PVC insulated unsheathed size 4 Sqmm complete all as specified and directed.

Switch piano flush type/Bell push/, 5 Amps, single pole one way complete all as specified and directed.

Switch piano flush type, 5 Amps, single pole two way complete all as specified and directed.

Socket 5 pins, 6 Amp, flush type piano (multi purpose) complete all as specified and directed.

Socket 15 Amps flush type, 6 Pin, 230 Volts , AC complete all as specified and directed.

Switch 15 Amps flush type 230 Volts , AC complete all as specified and directed.

Ceiling rose, surface bakelite, 65x50mm, three terminals complete all as specified and directed.

Angle lamp holder PVC/Polycarbonate base / back suitable for LED lamp complete all as specified and directed.

LED Bulbs 9W B-22 Pin type complete all as specified and directed.

Ding Door Bell, 230 volts, single pole complete all as specified and directed.

LED tube light along with fixture, 20W(4 feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused,fixed in repair complete all as specified & directed by Engr-in-charge Make : BAJAJ cat part no :BCLSB 20 WH or equivalent Havells cat part no: LUMILINEBSWLED865SPCWH or equivalent CG cat part no : LCTL-18-CDL

LED 6000K (2’ feet), 10W Decorative LED lighting fixture with extruded PVC , heat sink, environmental friendly, energy efficient ready to use pack, complete and including taking down existing fittings all as directed by Engineer-in-Charge. Make :- BAJAJ cat part no:BCLSB 10 W or equivalent Havells cat part no: LUMILINEBS9WLED865SPCWH or equivalent CG cat part no : LCTL-9-CDL

LED bulkhead luminaire 10W decorative type as per sample complete and including taking down existing fittings all as specified & directed by Engg-in-charge Make : BAJAJ cat part no:BIBWP 10W LED or equivalent Havells cat part no:RUGBYNEONFT10WLED860SSYMTOPC or equivalent CG cat part no : LBHE-10-CDL .

LED building secuity light 25 watt complete and including taking down existing fittings all as specified & directed by Engg-in-charge Make : BAJAJ cat part no:BCLST 25W LED I V2 or equivalent Havells cat part no: ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent CG cat part no : LSTS-25-CDL

Submain wiring with 2X6.0 Sqmm +1X4.0 Sqmm Earth Wire single core PVC insulated FRSL sheathed copper cable connecting to common earth dolly in and including heavy duty PVC concealed conduit , including dismantling and taking down existing unserviceable wiring all accessories complete all as specified and directed. .

VTPN 4 way double door prewired distribution board TPN-DPX 125 MCCB including one No MCCB 125 Amps, 25 kA, 4 pole as incomer and suitable SPN/TP MCBs as outgoing double door type sheet metal enclosure 415V with 200 Amps rated standard busbar of suitable size plate and common neutral link without MCBs with blank plate suitable for 4 way complete and taking down item including VTPN DB's all as specified and all as directed by Engineer-in-Charge. Note : Rates of MCCB and MCB SPN/SP/TP shall deemed to be included in the quoted rates.

Single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 ways including taking down existing DB's complete all as specified and directed.

MCB SPN 06 to 40 Amps 240V incl all termnials, fitting etc and including taking down existing MCB's complete all as specified and directed.

RCCBs for earth leakage protection 2 pole ,40 Amp rating, 30mA capacity suitable for 240 Volts and including taking down existing MCB/ RCCB complete all as specified and directed.

MCB SP 06 to 40 Amps 240V incl all termnials, fitting etc and including taking down existing MCB's complete all as specified and directed.

Exhaust fans of size 300 mm sweep, 1400 RPM (heavy duty) MS body incl blade with louver shutter with fasetner nut bolts washer etc fixed in repair complete all as specified & directed and deposit to MES Store Yard .

CRCA sheet metal enclosure suitable size for Energy meter and refixing energy meter, glass fixed on door with locking system, HDPE gland fixed on pole/wall/panel all as specified and directed by Engr in charge .

Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 15 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion.

Taking down unserviceable Air termination any type any description all as per specified and directed by Eng-in-charge.

Air termination single pointed copper rod 12 mm dia and 300 mm long with necessary fixing arrangement on roof complete all as specified and directed.

Taking down unserviceable roof conductors and down conductors (strip) any type any description all as specified and directed by Eng-in-charge.

Aluminium strip 25x3.15 mm with saddles and fixing screw for roof conductor and down conductos fixed on insulator on wall complete all as specified and directed. Note :- Porcelain insulators measured separately.

Taking down unserviceable Test point terminal block any type any description all as specified and directed by Eng-in-charge.

Test point terminal block made of phosphorus bronze size 75 x 75 x 25 mm thick drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screws fixed to copper strip bracket fixed to porcelain insulator in wall as in repairs, complete all as specified and directed

Porcelain insulator of suitable size for support of Earth strip with wall including nut bolts and washer of suitable dia complete all as specified and directed.

GI tube light grade size 40 mm bore laid in PCC foundation and protection/fixed strip incl welding works, clamp, nut/bolt as required ,complete all as specified and as directed.

All as per item No 153 above but size 15mm dia for protection/fixed air termination single pointed copper rod complete all as specified and as directed.

Cement concrete type C2 1:3:6 (40 mm graded stone aggregate) as in cable duct and foundation for air termination etc including form work as required complete all as specified and as directed.

Earthing complete with copper earth plate electrode of size 60 cm x 60 cm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below the normal ground level connected with Copper strip 32 x 6 mm by means of bolts, nuts, check nuts & washers of galvanished iron steel including necessary excavation and earth work in any type of soil, removing surplus soil to a distance not exc 50 m, with and including PCC chamber in PCC (1:2:4) , type B1, using (20 mm graded stone aggregate), mild steel angle iron frame made out of MS angle iron of size 40x40x6 mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6mm thick CI cover with handle, watering arrangement with funnel internally secured with wire mesh with 20 mm dia medium grade pipe for watering ,40 mm dia light grade GI pipe for lead protection in & including alternate layers of char coal dust and common salt complete all as shown in electrical plate No 5 and connected to earthing test point all as specified and indicated including testing on completion including retrieving old existing earthing complete all as specified and directed.

M/S Meera Builders

M/S Jaswant Kumar Aggarwal

M/S kuldeep kumar khullar

PRITPAL SINGH

Pankaj Builders

Ajinkya Constructions