Repairs to 2.5 cusec x 18 mtr head Horizontal split casing pump coupled with 40HP motor of pumping unit-I along with allied mechanical works at LIS pindi sarochana new and repairs to 75 hp motor along with allied works at L.I.S. Kothey parlah new

Amount

Repairs to 2.5 cusec x 18 mtr head Horizontal split casing pump coupled with 40HP motor of pumping unit-I along with allied mechanical works at LIS pindi sarochana new.

Decoupling of 2.5 cusec x 18 meter head dischargepump unit no I from 40 hp motor and then dismantling the pump and motor from the base frame. Carriage & shifting of dismantled pump and motor on head load to roadside using manual labour and then to workshop by carriage vehicle. Repair to 2.5 cusec x 18 meter discharge split casing pump of pumping unit no I of Lift irrigation station, pindi sarochana new at workshop by dismantling and extraction of all worn out/damaged parts i.e. pump shaft, impeller, bearings, sleeves, bush, check nuts, nuts & bolts, gland plate, gland studs. Properly cleaning the internal surface of pump casing. Providing and fitting of new pump shaft after turning to bearing size and threading at positions of check nuts. Repairs to impeller by filing cavities, cracks and finishing to original size. Providing and fitting 2 no’s of new bearing’s on driving and non driving end of the pump, 1 no’s neck rings, 2 no’s shaft protection sleeves, 2 no’s check nuts, nuts & bolts, fabrication of 2 no’s new gland plate with providing and fitting of 2 no’s new gland studs on ends of pump. Repair to bearing housing on non driving end of pumping unit by providing and fitting of bush, turning and fitting of bush to make inner diameter of bearing housing suitable for fitment of bearing. Providing and fabrication of bearing housing on driving end of the pump and drilling of holes as per the profile of pump. Reassembling all parts of pump with proper greasing of bearings and providing and fitting of gasket sheet between upper and lower part of the pump. Proving and fitting of graphite packing of suitable size on both ends of pump. Rewinding and repairs to 40 hp motor of pumping unit no I by extracting out old damaged winding manually and cleaning of stator slots. Inserting of insulation papers in slots, complete rewinding of the stator by using standard copper wire of requisite gauge. Making of connection coils in star delta. Tightening /locking of coils into the slots by using glass fiber wedges. Complete varnishing of the stator and allowing to completely dry. Repair to rotor shaft by way of welding the positions of bearings and coupling pulley, turning and finishing making the area smooth and balanced. Providing and fitting of two number new bearings 6309 and 6312 on driving and non driving end, nuts and bolts. Replacement of coupling pulley of pumping unit no I by way of fabrication of new coupling set as per sample and according to the size of motor and pump shaft. Providing and fitting of 8 no’s. new coupling nuts & bolts, rubber bushes, key way. Repairs to 40 HP starter of unit no- I at LIS pindi sarochana new by way of extracting the damaged worn out parts. Repair to Tripping system by brazing and finishing required size, Providing and fitting of no voltage coil, overload relay, moving and fixed contact point. Replacement of worn out thimbles nuts-bolts and internal leads duly soldered properly. Topping of starter with 10 liters of fresh transformer oil. Repair to 150 mm diameter foot valve of pumping unit no I by way of dismantling parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. The job includes fabrication of strainer to stop entry of unwanted material and fitting it with foot valve. The job includes loading, un-loading, manual labour, carriage charges of vehicle (to & fro), tools & tackles, cost of materials, installation& testing charges at site. Complete job.

Rebate on Old Parts

Repairs to 75 hp motor along with allied works at L.I.S. Kothey parlah new.

Decoupling of 75 HP motor from 8 cusec discharge pumping unit no III and then dismantling of motor from the base frame. Carriage & shifting of dismantled motor of LIS Kothey parlah new on head load through path in fields to roadside using manual labour and then to workshop by carriage vehicle. Repairs to 75 hp motor of pumping unit no III by extracting out old damaged winding manually and cleaning of stator slots. Complete rewinding of the stator by using standard copper wire of requisite gauge. Varnishing after rewinding of stator. Repair to rotor shaft by way of welding, turning and finishing to required size. Providing and fitting of new bearings NU215 -2 no’s on driving and non driving end, bearing plates- 2 no’s, end terminals, nuts and bolts. Shifting back of repaired pump and motors after carrying out repairs to site Replacement of coupling pulley for 8 cusec x 75 hp pumping unit by way of dismantling of coupling pulley from pump and motor shaft. Providing and fitting of new coupling pulley with coupling bolts and rubber bushes. Fabrication of key for motor and pump shaft as per the slot size. Repair to starter oil immersed of 75 HP motor , double contact of pumping unit no III by way of extracting the damaged contact points of copper both moving and fixed thimbles, no volt coil, tripping system , overload relay and replacing the same with new ones. Providing /filling of new T-oil 10 liters. Job includes cost of material, labour charges, fitting and installation charges of motor at site. Complete job.

Rebate on Old Parts

M/s RK Elect. Mech. Engg and fabrication works

PERFECT ELECTRICAL WORKS

SMART TECH AND CO