SPECIAL REPAIR OF GOVT MD ACCN BLDG NO P-62 OF ASD LINE AT COD JABALPUR UNDER GE (EAST) JABALPUR

M&L Water proofing treatment on "Non-Approachable/Non-accessible & Approachable Roof" in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

Taking down of old existing waterproofing treatment surface (Horizontal & Vertical surfaces) icluding properly cleaning & drying the concrete surface complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on roof or concrete surfaces complete all as specified and directed.

Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm

Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified 100 mm over laps shall be sealed by flame as per manufacturers instruction.

M&L for Cement concrete tiles 20 cm x 20 cm x 20 mm thick, machine pressed including provision of 15 mm thick screed bed in CM 1:4 with using water proofing compound complete all as specified and directed.

Supply only liquid waterproofing compound ISI marked complete.

Demolition of Cement Concrete (reinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for PCC 1:2:4 (Type B0 using 12.50 mm graded stone aggregate) in roof/ chajjah padding/kerbs/sunken slab etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises. Complete all as specified and directed.

Demolition of stone slabs and tiles of any escription or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as directed.

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for Non Skid Coloured Ceramic Tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick in vertical surface such as dado / skirting / risers to steps etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4. Complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for Machine cut Kota stone slab 20-25 mm thick in riser of steps, skirting, dado & pillar over & including rendering 10 mm thick in 1:4 cement mortar, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing. Complete all as specified and directed.

S&F factory made rubber moulded glossy finished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Machine cut Cudapph stone slab on cooking platform/shelf 20-25mm thick over cement base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete and including 15 mm thick 1:4 cement mortar screed bed complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick over & including 20 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing. Complete all as specified and directed.

M & L Granite work (table rubbed and polished) 20 mm thick n steps, jambs, pillars, window-cills, wash basin, cooking platforms and including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite bedded and jointed with grey cement slurry and pointed to match the shade of granite stone grinding and polishing types including screed bed 15 mm thick in CM 1 : 6 Complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations. Complete all as specified and directed.

M&L for PCC 1:2:4 (Type B1 using 20 mm graded aggregate) as in floor finishes 25mm thick laid in panels & finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:4:8 (Type D2 using 40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate as in plinth protection finished even and fair & smooth without using extra cement complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in :6 cement mortar. Complete all as specified & directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:4 cement mortar. Complete all as specified & directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement). Complete all as specified and directed.

M&L for 5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in ceiling

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement) complete all as specified and directed. (WPC measured and paid seperately)

M&L for preparation of new decorative surfaces of wall of walls including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

M&L for applying two coat of oil bound distemper over & including one coat of alkali resistant priming paint on newly prepared plastered ceiling surfaces. Complete all as specified and directed.

M&L for preparation of old painted ceiling surfaces & applying three coat of white wash on prepared ceiling surfaces. Complete all as specified and directed.

M&L for complete removal of existing treatment on brick work or concrete surfaces & old painted suerfaces & applying 2mm thick birla wall care putty complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & old painted suerfaces & applying 2mm thick birla wall care putty complete all as specified and directed.

M&L complete removal of existing any type of treatment of walls including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and Jet pressure washing and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

M&L for preparation of old painted brickwork or concrete surface & putty surface & applying one coat of oil bound distemper on brick work or concrete surface complete all as specified and directed.

M&L for preparation of old painted ceiling surfaces & applying two coat of white wash on prepared ceiling surfaces complete all as specified and directed.

M&L for preparation of old painted Steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of Synthetic enamel paint (ordinary tint). Complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint on steel & iron surfaces of any description, over 10 cm in width or girth including preparation of new surface and applying one coat of red oxide zinc chrome complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank. Complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity, hoisted and fixed in position all as specified in SSR Part-I, including dismantling of old u/s water storage tank. Complete all as specified and directed.

S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe & fixed. (Minimum weight 210 gms). Complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed in 20 mm bore dia of pipe. Complete all as specified and directed.

Taking up or down steel tubing and connections incl cleaning for refixing or removal form site for 15mm bore pipe all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections incl cleaning for refixing or removal form site for 20mm bore pipe all as specified and directed by Engr-in-charge.

S&F 20mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

Supplying and laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. ®

Supplying and laying 25 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. ®

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

Dismantling of plain or corrugated steel sheeting, fibre glass sheet any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, fibre glass sheet any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for Pre-painted galvalume zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPA as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws as specified.

M&L for Pre-painted galvalume zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 MPA as in roof covering/cladding to wall, including ridge of same colour fixed with self tapping screws as specified.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

S&F MS steel flat iron as in wind tie for roof sheet including securing bolts complete all as specified and directed.

Repairing sunken floor leakag as per following steps: Surface preparation:- (i)Prior to application of Dr fixit powercrite, ensure to clean the substract which shoud be free all the dust, foregn particles, loose aggregate and oll grease etc. This can be done with the help of scarifying, grinding water jetting and sand blasting etc. (ii)The surface should be wetted well prior to application throughly with water to get so condition. (iii) All the depression or pin holes/pot holes to be repaired using Dr Fixit powercrete method mortar in mixing ratio of (1 kg cement: 1.50 kg silica sand: 0.50kg of Dr Fixit powercrete). Coating application:- (i) Mix Cement with Dr. Fixit Powercrete in ratio of 1: 0.50 (1 kg cement OP CS3: 0.50 Dr. Fixit Powercrete) by weight. (ii) The mix should be stirred thoroughly until smooth homogeneous paste is obtained. (iii) Apply first coat over SSD/wet condition substrate. (iv) Apply and unroll woven glass fibre cloth evenly on the wet coating before it dries out on larger areas. (v) Using a nylon brush, apply a coat of Dr. Fixit Powercrete coating over the glass fabric so as to cover the fabric, allow 5-6 hours of air drying before application of another coat of Dr. Foot Powercrete slurry coating over the surface. (vi) Provide polymer modified protective plaster of 15-20 mm thick over the coating to ensure safety from mechanical damage.

Curing:- (i) Allow Dr. Fixit Powercrete coating to air cure for 3-6 hours after the final coat. (ii) Do not allow the rapid drying of the coating by covering the coating with help of polythene sheet in case of high humidity and windy condition. (iii) However, a moist curing after the air drying is advisable. (iv) Following the moist curing, Dr. Fixit Powercrete coating shall be allowed to air cured for 3 days before submerging it in water. Note - The above procedure is alven for Dr Fixit Powercrete any other equivalent make may vary as per manufacturer instruction and as specified by engineer in charge.

S&F in repair 15mm bore bib tap fancy type chromium plate alloy with a crutch or butterfly handle screwed down for iron pipes or for brass ferrule all as specified and directed by Engr-in-charge.

S&F in repair, 15 mm dia of bore, fancy type, chromium plated stop valves, cast copper alloy, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions. Complete all as specified and directed.

S&F in repair, 15 mm dia of bore, fancy type, pillar taps, chromium plated, cast copper alloy with capstan head, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for iron pipe or for unions complete all as specified and directed.

S&F in repair, 32 mm dia of bore, bottle trap, brass, chromium plated for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union & cap and fixed complete all as specified and directed.

S&F in repair, 32 mm dia of bore, Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed. Complete all as specified and directed.

S&F in repair 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 complete all as specified and directed by Engr-in-charge.

S&F in repair, Health Faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube & ABS wall hook including making connections & fixed in position complete in all respect as specified.

S&F in repair, Vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain & plug & porcelain stopper but including bracket & including supply & fixing of 32 mm dia of bore, brass chromium plated waste coupling. Complete all as specified and directed.

S&F in repair, Vitreous china wash down water closet pan (pedestal pattern), white, with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding fixing bolts, flushing cistern and flush pipe. Complete all as specified and directed.

S&F in repair, plastic water closet seat cover, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device. Complete all as specified and directed.

S&F in repair, Vitreous china squatting pan, 'Orissa pattern' size 580mm x 440mm, white, with integral foot rest excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repair, Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm. Complete all as specified and directed.

S&F in repair, 1 mm thick, Stainless Steel Plate Rack of overall size 24 inch x 36 inch x 10 inch including fixing with rawal plug and screws. Complete all as specified and directed.

S&F in repair, 10 ltrs capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. Complete all as specified and directed.

S&F in repair, flush pipe of polyethylenie of low or high density or PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F in repair, 125 mm size, brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F in repair, PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair, brass chromium plated, tubular towel rail, 20 mm dia, 'D' type, 60 cm long between flanges etc complete all as specified and directed.

S&F in repair, Brass chromium plated Sink Mixer with raised 'J' shaped swinging spout (Wall Mounted Model) with connecting legs & Wall flanges for 15 mm bore of pipe. Complete all as specified and directed.

S&F in repair, Sheet Glass Shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S&F in repair, toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete.

Taking down of eves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. Complete all as specified and directed.

S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius. Complete all as specified and directed.

S &F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S &F in repair, 110 mm bore PVC (SWR) vent cowl. Complete all as specified and directed.

S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius. Complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal. Complete all as specified and directed.

S&F in repair, Stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, Including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe. Complete all as specified and directed.

S &F in repair, 75 mm bore PVC (SWR) vent cowl. Complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.50 sqm each with shutters (without taking off shutters from the frame) and removing to store. Complete all as specified and directed.

Taking down Chowkhats or frames exc. 1.50 sqm but not exc. 4 sqm each with shutters (without taking off shutters from the frame) and removing to store. Complete all as specified and directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size45 x 85mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately. Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick decorative type comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws complete all as specified and directed. Note : stainless steel butt hinges and necessary S.S screws shall be paid separately.

Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size 125 x 65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately. Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F in repair Factory made single extruded WPC (Wood Polymer Composite) solid plain skeleton door shutter of 35 mm thick decorative type comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws including and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads complete all as specified and directed. Note : stainless steel butt hinges and necessary S.S screws shall be paid separately.

S & F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain RM coloured PVC sheet reinforced with MS square tube complete all as specified & directed.

S&F Factory made solid panel PVC door shutter30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottomrails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channelhaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stilesand plain colour PVC sheets for top rail, lock rail & bottom rail on either side & asgap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to befitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheetbeading, and joined together with solvent cement, suppling & fixing in the frame atsite as per specification & drawing.

S&F 100 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fored complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy & fixed complete all as specified and directed.

Taking down old wooden/wood based particle board & S&F 18/19 mm thick high density PVC solid fibre board duly laminated 2mm thick prelaminated PVC sheet on front face (ISI mark) etc in kitchen complete.

S&F 100 mm long hasp & staple aluminium anodised wire type, ind bolt to hinge plate and fixed with screw complete.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, Kg channels, plates, Kitchen rack etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F in repair, Diapory mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when RM open) 40 mm complete all as specified and directed.

S&F magnetic catcher with nut and screw of mild steel bright finish complete all as specified and directed.

S&F Providing and fixing of double rebate openable/fixed windows (Eco 4000) made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 4 mm thick plain clear glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. co

Provinding and fixing of Ventilators Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 D quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with comer bracket. The above frames should be fixed to the concrete/masonry walls including including 10mm Square bars welded to 6x12 mm flat at a distance 150m m c/c (pitch) etc by means of self expanding ScrewSil as per HQ CE JZ DRG No: CEJZ/TD/980 of Sheet 1/2 & 2/2 complete all as specified and directed

S&F Sheet glass 5.50mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as specified and directed

M&L Concrete bed to 150mm dia drain pipes including packing under, & haunching against the sides of pipes after they are laid & tested, in PCC (1:4:8) complete all as specified and directed

M&L Salt-glazed stoneware drain pipes laid in trenches & jointed as specified of 150mm dia complete all as specified and directed

M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces Complete all as specifed and directed

Taking up or down steel tubing in trenches/wall with connections including cleaning for removal all as specified and directed.

25 mm dia bore

20 mm dia bore

M&L for GI tubing medium grade with al fittings laid in trenches for bore of pipe of following sizes complete:

25 mm dia bore

20 mm dia bore

M&L for GI tubing medium grade with al fittings fixed on walls for bore of pipe of following sizes complete:

25 mm dia bore

20 mm dia bore

S&F Gun metal, glove Gate Valve with iron wheel head of 20mm dia bore complete with all accessories all as specified and directed by Engr-in-charge.

M&L for Cutting existing GI tubing for alterations or additions of 40/50mm dia bore for intersection of reducer Tee complete with all accessories all as specified and directed by Engr-in-charge.

Excavating in trenches in soft/loose soil n exc 1.5 m wide and n exc 1.5 m in depth; and getting out for taking up/laying under ground electric cable complete with accessories all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in depth complete with accessories all as specified and directed by Engr-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete.

Excavating in trenches in any tpe of soil n exc 1.5 m wide and n exc 1.5 m in depth; and getting out for foundation of poles/stays/cables etc complete all as specified and directed by Engr-in-charge.

M&L for Sand cushioing in cable trenches over and under the cable, with river washed coarse sand as per standard practice with proper compaction complete all as specified as directed. (Punned thickness 18cm shall be considered for payment as per para 19.75 of SSR Part-II)

M&L for fly ash brick sub-class 'B' locally avilable laid flat in trenches over sand cushioning for cable protection complete all as specified and directed

S&F 40mm dia GI tubing light grade ISI marked fixing to pole with suitable clamps/laid under floor/road for protection of cable including complete all as specified and directed

Disconnecting & taking out defective under ground LT cable from trenches, pole, pipe, floor, wall etc including bricks GI pipe and removing formwork site of unserviceable material of any size complete all as specified and directed.

Supply, laying and testing 11000 volts (E) grade, XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor of cross sectional area 25 sqmm, 3.5 core conforming to IS 7098/ (PART-II) 1985 with latest amendments and testing on completion complete all as directed. Note:- Excavation, earth work, sand cushioning and cable protection shall be measured and paid for separately under respective items of BOQ.

M&L for boring of holes under road/pavement /hard standing by trenchless technology with neccessary machineries for inserting the GI pipe of size upto 40 mm working pressure dia complete all as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, holders, pendants, regulators, sockets etc and making good disturbed surface by using cement mortar, white cement, putty etc and match with existing surfaces of walls, floors etc complete all as specified as directed.

Taking down carefully any type of old unserviceable submain wiring with PVC/steel conduit surface / concealed or wooden battens etc and making good the disturbed surfaces to match with the existing surface complete all as specified & directed by Engineer-in-Charge.

Taking down carefully any type of DBs including MCCBs and MCBs for keeping the old materials into safe custody or for taking credit(credit for above items should be made as per condition seaparately) and making godd to the disturbed surface etc complete all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost all as specified and as directed for One light point controlled by one switch 5/6 Amps.

ditto as per item No. 04 but for one Ceiling fan/Exhaust fan Point controlled by one switch 5/6 Amps.

ditto as per item No. 04 but for one Bell/buzzer Point controlled by one push button switch 5/6 Amps .

ditto as per item No. 04 but for one socket point 5/6 Amp controlled by one switch on same board.

ditto as per item No. 04 but for one socket point 5/6 Amp controlled by one switch on Independent board.

ditto as per item No. 04 but for one light point controlled by two way switch.

Description same all as per item No. 4 here in above but with 1100 Volts grade copper stranded conductor FRLS cable of size 2.5 Sqmm main & with 1.5 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 5/15 Amp on Independent board complete all as specified & directed by Engineer-in-Charge.

Description same all as per item No. 4 here in above but with 1100 Volts grade copper stranded conductor FRLS cable of size 4 Sqmm main & with 2.5 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 5/15 Amp on Independent board complete all as specified & directed by Engineer-in-Charge.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, all as specified and as directed. NOTE : Two runs of 4.0 sqmm conductor for main and one run of 4.0 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, all as specified and as directed. NOTE : Two runs of 6.0 sqmm conductor for main and one run of 6.0 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

S&F call bell multi music type suitable for AC 230 volt single pole complete all as specified & directed.

S &F Lamp holder, PVC/ polycarbonate type with back plate for angle holder all as per specified and directed.

S&F Ceiling rose surface type 60 x 30 mm three terminals of polycarbonate body complete all as specified & directed.

S&F modular switch one way 6 Amps one module 230 volts AC complete all as specified and as directed.

S&F modular switch one way 16 Amps one module 230 volts AC complete all as specified and as directed

S&F modular socket, 6A -2/3 pin combined 2 module,230 volts AC complete all as specified and as directed.

S&F modular socket, 6/16A -2/3 pin combined 2 module, 230 volts AC complete all as specified and as directed .

S&F modular bell push , 6 Amps, 1 module complete all as specified and as directed.

S&F modular switch two way AC 230 volts 6 Amps ,1 module complete all as specified and directed.

S&F modular fan regulator, 2 Module 4 step upto 120 W heavy duty 230 volts complete all as specified and as directed.

S&F modular cover plate 1 module including screws and washers etc complete all as specified and as directed.

S&F modular cover plate 2 module including screws and washers etc complete all as specified and as directed.

S&F modular cover plate 3 module including screws and washers etc complete all as specified and as directed.

S&F modular cover plate 8 module including screws and washers etc complete all as specified and as directed.

S&F modular cover plate 12 module including screws and washers etc complete all as specified and as directed.

S & F Metal flush box 1/2 module complete all as specified and directed.

Ditto as per item No. 179 but 3 module complete all as specified and directed

Ditto as per item No. 179 but 8 module complete all as specified and directed

Ditto as per item No. 179 but 12 module complete all as specified and directed

S&F Sheet metal enclosure MCCB DB VTPN 4 Way vertical type 250A copper busbar for each phase fully insulated busbar and shrouded neutral bars with provision for DPX 160 MCCB as incomer and SP/TP/MCB's as outgoing reversible door for IP 43 IK-09 DB's system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed by Engr-in-Charge.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral,240 Volt with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed by Engr-in-Charge. (Note : MCBs will be Measured separately)

Supply and fixing MCCB, four pole, 100 Amps, 415 Volts of breaking capacity 16 KA complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB), TPN, 63 Amps current carrying capacity in the DB complete with connection, testing and commissioning, all as specified and directed.

Supply and fixing 240V 10KA 'C' curve miniature circuit breaker (MCB), SPN, 40 Amps current carrying capacity in the DB complete with connection, testing and commissioning, all as specified and directed.

Supply and fixing 240V 10KA 'C' curve miniature circuit breaker (MCB), SP, 6-32 Amps current carrying capacity in the DB complete with connection, testing and commissioning, all as specified and directed.

Supply & Fixing Smart bright Batten Series, LED luminaire using LEDs 20 watt min 100 LM/watt, natural white(4000K)/ cool white (6500k), with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output with wide voltage protection range, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall/ceiling mounting fixed with 02 Nos of PVC round/ square blocks, screws etc(supplied along with The Luminaire has been tested as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), report has established conformity of the product(s) to the requirements of the Standard/Specification.

Supply and fix in replacement of LED bulk head luminaires,9 watts (600-900 lumens) lamp with fittings, connecting cable PVC insulated and PVC sheathed copper flxible cable with suitable size up to ceiling rose and necessary fixing arrangments complete all as directed.

S&F IP 20, Class I, LED Mirror light fitting10 W, (or nearest next higher wattage) wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size etc complete all as specified.

Supply & fix in replacement of LED Security Light Luminaire 35 watt with 2500 or more lumen warm white/cool day ligh with, surge protection device upto 4KV, IP65 or more, IK07 or more, potted driver suitable for 180 to 270 V, 50 Hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole/wall fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

S&F in replacement of LED Bulb 5 star rating 230V AC 12 watt warm/cool day light 6500K as per the direction/requirement of site complere all as specified and directed by Engineer-in -charge.

S&F decorative wall light fitting made up of Polycarbonate ,Cylindrical shape or as per the sample required/obtained from the site and mounting arrangement to fix the lamp and all as directed by Engr-in-Charge with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed.

Taking down ceiling /exhaust fan sealing cable end, dismantling blades and removing fan and blades to store complete all as specified by Engr in charge

Hanging only ceiling fan and connecting up including provision of flexible cable from ceiling rose or connector to fan Including hook and clamps with nut ,bolts, washers etc complete all as specified and directed

Fixing only exhaust fan and connecting up including provision of flexible cable from ceiling rose or connector to fan Including nut ,bolts, washers etc complete all as specified and directed

M & L for painting of ceilling fan of any make/model and size complete with one coat of 1st grade quality of synthetic white enamelled paint by spraying including preparation of old paianted surface to remove all dust, oil mark etc and filling cavaties with filler materials, before painting , complete writing the MES numbers on ceiling fan with flack synthetic enamel paint of 1st grade quality by stenciling with uniform size of letters/of figures n.exc 20 mm in height letters/figures to be written in each fan complete all as spedified and directed.

M&L for sheet metal enclosure fabricated out of 2.0mm thick CRCA sheet, totally enclosed type, dust and vermin proof with suitable sized supporting MS angles and suitable openings at top and bottom for entry of outgoing/incoming cables, fixed with nuts and bolts and front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer with suitable glass vision panel of each meters shall be provided in the door to easy meters reading and providing all electrical connections with minimum dimensions (90 x 75 x 25 cm) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters including danger notice board etc complete all as specified by Engr in charge

M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type B1 using 20mm graded stone aggregate with angle iron CI frame 40X40X5mm , CI cover with provision of locking arrangement complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified and directed by Engr-in-Charge. including necessary excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal. Note :- (i) Earth protection pipe & earthing wire upto and including 7.5 m length is deemed included in unit rate quoted by the contractor (ii) If earth resistance of earthing is not found satisfactory it will be redone by the contractor without any extra cost to Govt.

Schedule of credit amount of Rs. 1,80,436.50 to be deducted during AOC

Please Enable Macros to View BoQ information