Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹36.2 LAccepted-AOC NEAR LIC OFFICE KALAIGNAR ARIVALAYAM SHOP ROOM NO7 GROUND FLOOR OF BACK SIDE PHOENIX BAY SRI VIJAYA PURAM 744101 | SRI VIJAYA PURAM | SOUTH ANDAMAN | ANDAMAN AND NICOBAR ISLANDS | 744101 | 1 | Accepted-AOC LOWEST | |
| 2 | 2₹40.0 L+₹1.6 L (4.11%)Rejected-Finance | 2 | Rejected-Finance LOWEST | |
| 3 | 3₹42.9 L+₹4.5 L (11.6%)Rejected-Finance | 3 | Rejected-Finance NOT LOWEST | |
| 4 | 4₹43.0 L+₹4.6 L (12.0%)Rejected-Finance | 4 | Rejected-Finance NOT LOWEST |
Tender Value
₹35.0 L
EMD Value
₹69,900
Closing Date
28 Dec 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (AF) PALAM
GE (AF) PALAM DELHI CANTT-10
REPAIR TO SCHOOL/ OMQ BUILDINGS IN RV AREA AT AF STN PALAM UNDER GE (AF) PALAM, DELHI CANTT-10
2023_MES_625936_2
GENP-54/2023-24
Open Tender
Civil Works
Item Rate
180 days
GE (AF) PALAM DELHI CANTT
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
GE (AF) PALAM
₹69,900
Yes
19 Jan 2024
8 Dec 2023
30 Dec 2023
8 Dec 2023
28 Dec 2023
16 Dec 2023
Amount
B/R Works Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc removing debries from sites to out of MoD land.
Demolition of brick work/ stone masonry built in cement or cement lime mortar including all quoins, arches, pillars etc of any description including removing the debris from site to outside MoD land.
Demolition of cement concrete of any discription and in any position not otherwise specifically provided for including removal of debris from site to outside MoD land.
M&L for brick work with sub class 'B' works, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all specified.
M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 including finishing surface even and fair without using extra cement .
M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 including finishing surface even and smooth without using extra cement .
M & L for 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection including finished even and smooth without using extra cement including making joints 12 mm wide to the full depth of concrete at every 3 metres and at every change of direction and filling the same with & including bitumen85/25 and sand in the proportion of (1:3 ) by weight complete all as specified.
Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each.
Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exc. 4 Sqm each.
Taking down shutter of any discription area not exc 1 Sqm each.
Taking down shutter of any discription area exc 1 Sqm and not exc. 2 Sqm each.
M&L for factory made pressed steel frame for door with one or more rebated of size 105mm x 60 mm with necessary fixing lugs, hinges , lock strike plate and inserting holdfasts and making good dismantalled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required including cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in back filling of frame etc complete all as specified.
S&F for 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified.
S&F for butt hinges, 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21.
S&F for aluminium anodised, barrel tower bolts of extruded section and fixed of size 150mm.
S&F for cast type anodised aluminium handles of size 150 mm.
S&F for 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified.
S&F for anodised aluminium power coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc all as specified.
S&F for anodised aluminium power coated (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodisedaluminium snap beading, screws etc. and the making good of surface such as opening , plastering jambs, levelling and finishing complete all as specified.
S&F for aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window with mosquito net two track for glass leaf sliding and one track for mesh leaf sliding outer frame weighing 0.699 Kg/m,75mm x 26 mm size, shutter plain of size 37.5mm x 15mm weighing 0.366 Kg/m with one or more rebates, sliding type without sash bars, 5mm thickness double tampered clear glass , rubber packing, snap beading screws,with horizontal sliding type with Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm , frame, powder coated aluminium grill type AL-925 or its equivalent grill, cutting in suitable size and fitting with screws and suitable beeding to aluminum window frame complete all as specified.
M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint with one coat of wall primer over 2mm thick wall care putty complete all as specified.
M&L for complete removal of existing treatment of old decorated external surface of walls by electrically operated grinder including necessary scaffolding etc and applying two coats of exterior emulsion paint with one coat of primer over 2mm thick wall care putty complete all as specified.
M&L for preparation of newly plastered surface of walls and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified.
M&L for complete removal of existing treatment of old decorated external surface of walls by electrically operated grinder including necessary scaffolding etc and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified.
M&L for preparation of newly wooden or wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.
M&L for preparation of old painted surfaces of wood & wood based surfaces of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in charge.
S&F in repair steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for structural trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I S : 1161-1979 grade St.-24 including necessary machinery upto 10m height structure complete all as specified.
S&F in repair mild steel work framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.
Dismantling of asbestos cement/ steel (corrugated, semicorrugated etc.) sheets in roof covering, ridge etc complete all as specified.
S&F for 0.50mm pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.
S&F for 0.50mm pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.
M&L for two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surface of any description over 10cm width or girth including preparation of surfaces complete all as specified.
M&L for applying two coats of synthetic enamel paint on old concrete and plaster surfaces of any description over 10cm girth or width over a coat of primer including necessary preparation all as specified.
S&F in repair 'E' board ceiling 4mm thick with GI framed work with main tee of size 24mm x 28.5mm made out of PGI sheet 0.3mm thick doubled at web and single at flange. Flanage covered with powder coated sheet 0.35mm thick and wail angles 24mm x 24mm x 0.3mm powder coated for ceiling, ceiling board 60cmx60cmx4.00mm thick, suspended with GI wire 2.24 mm dias and length as required @ 600mm C/C with adjustable device complete including plugging in brick/concrete work with steel raw plug @ 600 mm C/C and applying two coats of OBD over a coat of primer on ceiling board. Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides all as specifed and directed including making good all the disturbed portion complete all as specified and directed.
Dismantling of timber scantlings of 40 Sqcm and over in section, in any position complete all as specified.
S&F for second class hard-wood timber, clean swan, in scantling on the solid rounded or chamfered put together with glue pinned at joints complete all as specified.
M&L for 60mm thick factory made, machine pressed with grey cement and no pigment interlocking paver blocks of any size and shape conforming to IS 15658-2006 of grade M-35 concrete complete over and including 25mm thick sand cushion complete all as specified.
M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified.
M&L for Galvanised Iron 'Z' section of 2mm thick fixed on existing rafter by self drilling screws zylem coated with rubber and metal washer including dismantling of existing wooden purlin, rafter etc complete all as specified.
E/M Works Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including making good disturbed surface of walls, floors etc complete all as specified.
M&L for point wiring complete with 1.5 Sqmm (nominal area) FRLS PVC insulated, multi stranded, copper conductor cable unsheathed including PVC conduit and fittings, medium grade, ISI marked and PVC insulated copper conductor cable of size 1.5 Sqmm as earth wire , connected to common earth dolly suitable for mounting modular switches including modular metal flush box and modular face plate with frame includes cutting of chasis and making good disturbed surfaces all as specified and as directed by Engr-in-charge for a light points/fan point etc complete.
All as per item No 41 above but for 5 Amp socket point on same board complete all as specified.
All as per item No 41 above but for 5 Amp socket point on independent board complete all as specified.
All as per item No 41 above but for one 6 pin socket out let 15 Amps on independent board with cables 2.5Sq mm size and earth wire 2.5 sqmm complete all as specified.
M&L in repair modular switch 1 way 6 Amps 1 module complete.
M&L in repair modular switch 1 way 16 Amps 1 module complete.
M&L in repair modular socket outlet 6A, 2/3 pin combined 2 module complete.
M&L in repair modular socket outlet 6A/16A, 2/3 pin combined 2 module complete.
S&F in repair MCB SP 'C' Series 6 to 32amps having breaking capacity 10KA.
S&F in repair MCB SPN 'C' Series 32 Amps having breaking capacity 10KA.
S&F in repair MCB four pole 'C' Series 100 Amp 415 volts breaking capacity 10 KA.
Taking out old unserviceable submain wiring of any size complete all as specified.
M&L for sub main wiring with multistranded copper conductor cable FRLS PVC sheathed in and including concealed steel conduit and all fittings medium grade with two runs of 2.5 Sq mm and one run of 2.5 Sq mm flexible copper wire as earth wire and connected to earth dolly including chasing, cutting and making good the disturbed surfaces as specified.
M&L for sub main wiring with multistranded copper conductor cable FRLS PVC sheathed in and including concealed steel conduit and all fittings medium grade with two runs of 6.0 Sq mm and one run of 6.0 Sq mm flexible copper wire as earth wire and connected to earth dolly including chasing, cutting and making good the disturbed surfaces as specified.
M&L for sub main wiring with multistranded copper conductor cable FRLS PVC sheathed in and including concealed steel conduit and all fittings medium grade with two runs of 4.0 Sq mm and one run of 4.0 Sq mm flexible copper wire as earth wire and connected to earth dolly including chasing, cutting and making good the disturbed surfaces as specified.
Taking down any type of light fitting of any capacity or wattage or size complete all as specified.
S&F for wall mounted LED integrated batten, NAKSHATRA P SERIES of capacity 20 watt complete with all accesseries making connection complete all as speficied and directed by Engr-in-charge .Cat part No LTTB4F20WLED P/W Make C&S or its equivalent in Philips/Havells.
S&F in replacement of sheet metal enclosures for TPN distribution boards 8way 415 V, having IP 43 protection, double door flush mounted. Having 200 Amps bus bar for each phase assembly as per IS 8623 all as specified.
Supply and fixing in replacement of sheet metal enclosures for SPN distribution boards 4way, having IP 43 protection, single door flush mounted. Having 200 Amps bus bar for each phase assembly as per IS 8623 all as specified .
Supply and fixing in replacement sheet metal enclosures for SPN distribution boards 8way, having IP 43 protection, single door flush mounted. Having 200 Amps bus bar for each phase assembly as per IS 8623 all as specified.
Supply, installation and testing for maintenance free grounding (earthing) system complete burried directly in ground vertically (earth pit not less than 3 mtr below ground level) by making bore hole of 100 mm dia for inserting 01 No 17 mm dia molecular copper bonded high tensile low carbon steel circular earth electrode of 3 meter length with average copper thickness of 200 microns alongwith environmental friendly grounding enhancing compound and heavy duty (HDPE) PVC pipe cap all in below ground level and connected to copper strip 25 x 3 mm flat by means of brass metal bolts , nuts and washers etc including protection pipe of GI 40 mm bore med grade upto 7.5 meter length and connection of earth lead to maintain distribution /LT panel board/DG set with copper lugs complete all as specified and directed by engineer in charge. (Note : The rate for necessary earth work ,PVC pipe,copper strip and all required materials shall deemed to be included in quoted rate by contractor and nothing extra shall be paid on this account).
Supply and fixing in replacement of metal plug and socket with MCB and steel enclosure of capacity 20 Amp, SPN, MCB metallic complete all as specified.
Taking down carefully ceiling/exhaust fan and re-fixing the same after completion of job all as speciifed and directed by Engr-in-Charge.
S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture not more than 1.4mm fixed with stainless steel wire staples complete all as speciifed.
Shiv Shankar Nirman Co.
VIJAY KUMAR GUPTA
M/S Davinder Kumar
stage.html
html • 0.05 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .