SPL REPAIRS TO BLDG NO P-3 AT JNE AND ARBORICULTURE WORKS IN RESIDENTIAL AND OFFICIAL ACCOMODATION FOR DEO AND DAD AT UDHAMPUR UNDER GE (NORTH) UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) , all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ) , all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including filling voids with PCC 1:3:6 type C-0 complete all as specified and as directed.

Description all as per item No 5 above but frame size 105 x 60 mm.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-290 grade-E-165, complete all as specified.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified.

35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified.

2nd class hard wood (Sal/ Hollock), glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I for door shutters, complete all as specified.

18/19 mm thick prelaminated particle board (ISI marked), exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work for kitchen cabinet stand board etc including 6mm thick teak wood beading all around, incl dismentling of old existing shutter, complete all as specified and as directed.

Stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete, all as specified. (ISI Mark)

Mild steel, 150 mm, ordinary pattern helical door spring including roller and roller plate fixed to wooden or steel frames with welding/fitted with screws etc.,complete all as specified and as directed.

75mm butt hinges ,medium weight ,cold rolled mild steel all as complete all as specified and directed.

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete, all as specified. (ISI Mark)

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Aluminium handle, cast type, anodised, 100mm long (ISI marked), complete all as specified.

Aluminium handle, cast type, anodised, 150mm long (ISI marked), complete all as specified.

100mm size hasp & staple, mild steel, safety type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified.

Aluminium handle, cast type, anodised, 125mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, complete all as specifed.

Powder coated (not less than 50 micron) aluminium frames for door/ windows/ ventilators of approved design with one or more rebated including jointing cleats with all fixing arrangement, complete all as specified and directed.

S & F powder coated (of approved colour ) aluminium (minimum thickness of powder coated 50 micron ) as in shutter of windows, ventilators openable/ louvers fixed/sliding type without sash bars, aluminium section not less than 0.55 kg/m including nessery jointing,cleats,glazing clips,rubber,neoprene packing, aluminium snap beding,screws , rolling for smooth moving & locking arrangement, etc fixed to wall including, preparation of disturbed portion both side (internal & external surfaces of wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified and as directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Description all as per item No 28 above but pin head type, figured glass.

Cutting holes through brick wall in cement mortar for inserting hold fast and making good dismantled portion in cmeent mortar 1:3 or cement concrete 1:2:4 type B-1 as required exc half brick but n exc one brick complete all as specified and as directed.

Prepration of new steel surfaces of any description over 10cm width or girth and applying two coats synthetic paint (For steel surfaces) over a coat of red oxide primer complete all as specified and as directed.

Preparing surfaces of wood and wood based materials, steel & iron work, new or old of any description and girth, not otherwise described, and treated with tar or coal tar black paint, complete all as specified & directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for sunken floor.

Demolition of cement concrete (un reinforced) as in roofs of existing water proofing treatment of any type and any thickness, complete all as specified and as directed.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed.

Non-skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick bedding layer in cement mortar 1:4, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Glazed coloured ceramic tiles 7mm thick 450mm x 300mm thick on vertical surfaces of walls as in dado/skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed.

18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting and polishing over and including 20 mm thick screed bedding/ backing layer in CM 1:4, complete all as specified and as directed.

Machine cut kota stone single piece slab flooring 18 to 20 mm thick over 20mm thick screed bed in cement mortar 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including protruding chamfered/rounded edges in threads table rubbed and mirror polished rubbing and polishing, complete all as specified and as directed.

Kota stone single piece slab 18 to 20 mm thick in riser of steps, skirting, dado and pillar laid over including 10mm thick in cm 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing protruding chamfered/rounded edges in threads table rubbed and polished and polishing, complete all as specified and as directed.

PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality .

S&F in repair 15 mm bore fancy type chromium plated stop valve of cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed.

S & F in repairs 15 mm dia bore fancy type chromium plated concealed stop valves of cast copper alloy with long shank & cup etc. complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S&F Soap dish with stain less steel of size 160x160x90mm fixed to plugs on wall with chromium plated brass screws complete all as specified and as directed.

S&F in repair 15 mm dia bore fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F Brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe for Wash Hand Basin with wall flange, complete all as specified.

S&F sink mixture with regular swinging spout wall mounted) with connecting legs & wall flanges, complete all as specified.

S&F stainless steel plate racks of size 750mm x 900 x 250mm and thickness of SS strip of 1mm fixed on wall etc complete all as specified.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm incl 32mm waste fittings brass chromium plated etc complete all as specified.

S&F for mirror cabinet PTMT of 450mm x 600 mm with magnetic looking arrangements fixed with and including chromium plated brass screws and PVC rawl plugs complete all as specified.

M&L for 25mm dia Stainless Steel curtain rod fixed in repair with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories . Note : The cost of brackets and knobs is deemed to be including in the quoted rate. Nothing extra shall be paid on this account.

Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store.

Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store.

Taking up or down GI tubing 25mm to 32mm bore pipe including cleaning for re-fixing or removal to store.

S&F GI tubing 15 mm bore medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, complete all as specified

S&F GI tubing 20 mm bore medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors complete all as specified.

S&F GI tubing 25 mm bore medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, complete all as specified.

Refixing old 15mm steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Refixing old 20mm steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Refixing old 25mm steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

S&F GI tubing 32 mm bore medium grade galvanised pipe for spout laid in sunken portion/ floors, complete all as specified and as directed.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories)

Supply and fixing in repairs cast iron floor trap with SS grating including jointing with solvent cement, 75mm diameter of outlet.

Dismantling of cast iron or RCC drain pipes including all fittings and accessories, 100 mm dia and in any position .

Dismantling of cast iron or RCC drain pipes including all fittings and accessories, 75 mm dia and in any position .

S&F cast iron spun pipes, 75 mm double socketed in any length with cement joints, fixed to walls .

S&F cast iron spun pipes, 100 mm double socketed in any length with cement joints, fixed to walls.

S&F cast iron bends suitable for 100 mm bore pipe, complete all as specified and as directed.

S&F cast iron bends suitable for 75 mm bore pipe, complete all as specified and as directed.

S&F cast iron branch pieces single, (single T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 100mm dia, complete all as specified and as directed.

S&F cast iron branch pieces double, (double T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 100mm dia, complete all as specified and as directed.

S&F cast iron branch pieces single, (single T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 75mm dia, complete all as specified and as directed.

S&F cast iron branch pieces double, (double T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 75 mm dia, complete all as specified and as directed.

S&F cast iron vent cowl of 100mm bore, complete all as specified and as directed.

S&F cast iron vent cowl of 75mm bore, complete all as specified and as directed.

S&F in repairs 20mm gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed .

S&F vitreous china wash down water closet pan `P` trap ( pedestal pattern ) white including fixing bolts,including connection P trap etc to drain pipe ( or out going pipe) and to flushing pipe,antisyphonage pipe etc complete.all as specified & directed.

Supply and fixing in repairs PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connecting to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified.

S&F corner glass shelf fixed with brass screws etc. complete.all as specified & directed.

S&F in repair wash hand basin of size 550 x 400 mm vitreous China white padestel type including brackets brass chromium plated waste coupling, pillar tap & PVC waste pipe of 32 mm dia etc complete all as specified.

Taking down old PCC tiles form roof and removing bedding at any position, complete all as specified.

15 mm thick cement plaster in cement mortar 1:3 on roof surfaces finished even and smooth without using extra cement, incl mixing of water proofing compound for Accessable roof/Non Accessable roof.

M&L for machine pressed factory made, glossy finish, coloured cement concrete chequered tiles of size 30cmX30cmX 22/25mm thick, set, jointed and pointed in neat cement slurry with pigment as in flooring, laid/ fixed over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for taking down existing roof treatment of any description and any type .

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.00 Kg of cement per sq m .

Supply only water proofing compound complete, all as specified and as directed.

M & L for apply bituminous primer confiriming to IS -3384 @ 0.40 Kgs/ Sqm on prepared surface on sunny day. After the primed surface has dried and apply a coat of hot blown 85/25 penetration grade blown bitumen, confirming to IS -702@ 1.20kg/ Sqm on the surfaces. Provide APP (Atactiic Polypropylene) modified polymeric five layered membrane with central core of 100 micron high molecular high density firm. Minimum weight of membrance will be 3 kg/Sqm. APP membrance will be laid across the slope from lowest line sloping roof towards ridge with minimum end lap of 150 mm & side lap of 75mm bonded with hot blown bitumen. Over the APP membrance apply semi hot blown 85/25 penetration grade bitumen @ 1.20kg/ Sqm and blinded with fine sand in dry condition @ 0.50 kg/Sqm dusted over the bitumen coat. WITH ALUMINIUM PAINT Note :- The laying of the membrane shall be got done by authorized applicator of the membrane manufacturer.

Making benching with PCC (1:2:4) type B1 using WPC along side wall adjoining to roof kerb in concave shape .

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed.

M&L for rendering 10mm thick in patches in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement.

M&L for rendering 15mm thick plaster in CM 1:4 mixed with WPC as per manufactures instructions in two layer (10mm+5mm). in patches in cement mortar in 1:4 on smooth face of brick work or concrete surfaces finishd even and smooth without using extra cement & with using integral water proofing compound .

M&L for rendering 5mm thick in cement mortar in 1:3 on ceiling finishing even and smooth without using extra cement.

M&L for reinforced cement concrete 1:2:4 type B1 (20 mm graded aggregate) as in chajjas complete all as specified.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:4 in half brick wall, complete all as specified.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified.

75mm thick plain cement concrete 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in plinth protection, surface finished even and fair, complete all as specified.

Demolition of RCC of any description such as Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not otherwise specially provided for (reinforcement cut as required to facilitate demolition)

Reinforced cement concrete (Design mix) using (20 mm graded aggregate) confirming to M-25 grade as in Slab supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and etc.

TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified .

TMT steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified .

Use and waste of form work to flat rough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick

Use and waste of form work to edge of concrete flat treads breaks in floor window cill concrete railing opening of concrete wall, flore, roof n.exc 20 cm wide and side of RCC bands in wall horizontal/sloping and similar works exc 10 cm but n.exc 20 cm wide for roughed finished surfaces of concrete.

Dismantling water tank and remove to Store of capacity exc 500 but not exc 1000

S&F 1000 ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position .

S&F 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) etc complete.

M&L for preparing new plastered surfaces and Applying 2 to 3mm wall care putty in wall surface and smoothening the surface with sand papers / Mechanised sanding etc and applying two coat of Oil Bound distemper of approved tint over a coat of alkali resistant primer .

M&L for preparation of surfaces and applying three coat of white wash on newly plastered surface of ceiling etc .

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over a coat of wall care putty over new/old surfaces.

S&F in repair Eye door viewer (magic eye) fixed in position for door shutters .

Rubber sheet 50mm wide and of thickness not less than 3mm fixed with stainless steel screws at the bottom of the door shutters .as in door cile.

Stainless steel fancy type peg set of four and fixed in position with steel screws .

M&L for grinding and polishing existing kota stone flooring, complete all as directed to rhe entire satisfaction of Engr-in-Charge.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, fixed to walls, any height including taking down old, complete all as specified & directed.

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc, complete all as specified and as directed.

Point wiring with 1.5 Sqmm PVC insulated, unsheathed (FRLS) cable with multi stranded copper conductor wiring in and including PVC concealed casing and caping medium grade (ISI marked) 20mm dia and over, wall thickness not less than 2.00 mm thick , and all accessories for one light / bell /exhaust fan controlled by one switch with 1.25mm thick pressed steel terminal anodized box concealed on walls, 3mm laminated plastic sheet cover for mounting of switches, socket outlet, regulator etc or suitable for switches, socket outlet, regulator etc , fixed by suitable size of 4 Nos cadmium screws along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly, complete all as specified and as directed.

All as per description of Serial item No 120 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per description of Serial item No 120 here-in-before but for one 3 pin socket outlet 5 Amp independent.

All as per description of Serial item No 120 here-in-before but one 3/5 pin 15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly.

All as per description of Serial item No 120 here-in-before but for one 3 pin socket outlet 5 Amp on the same board with other switches.

All as per description of Serial item No 120 here-in-before but for one light point controlled by two 2 way switches.

Switch piano flush button single pole one way 5/6 Amp, 240 Volts, complete all as specified and as directed.

Switch socket outlet, 2 in 1, 3 pin, 5 Amp flush type , complete all as specified and as directed.

Switch piano flush button single pole one way 15 Amp, 240 Volts, complete all as specified and as directed.

Switch socket combination, 2 in 1, 3/5 pin, 5/6 & 15/16 Amp flush type, complete all as specified and as directed.

Bell push 6 Amps 230 volts complete all as specified and as directed.

Switch piano flush button single pole one way 5 Amp, 240 Volts, complete all as specified and as directed.

Ceilling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, complete all as specified and as directed.

Fan regulator 120W, 230V 50 C/S, flush type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

Bell (ding dong type), AC electronic type, 230 volts, single pole ,fixing in repairs, complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 1 feet, 05 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor, having service value > 5.0 including making connection with and including suitable flexible copper wire, including taking down old fan and diposting to MES store, complete all as specified and as directed.

Environmental friendly, energy saving, surface mounted, decorative LED 10 Watt Bulk head luminire, with integral electronic LED driver with APFC and lower THD, Output complete making connection and testing after fixing all as specified and directed by Engr-in-charge.The specification of light fitting should meet the following :- (a) Housing of Light fitting : Die Cast Aluminium (b) Diffuser : Polycarbonate UV protected diffuser (c) Operating Voltage : Between 140 V- 270V (d) Operating Temperature : -10 to +45 Degree Centigrade (e) Lumen efficacy : Not less than 100 lm/W (f) System Lumens : Not less than 900 lm (g) Colour Temperature : Not less than 5700K (h) Surge Voltage Protection : Up to 4kV (j) Ingress protection : IP 65 (k) Total Harmonic Distortion (THD) : Not less than 20% (l) Power factor : Not less than : 0.9 (m) Line protection : Under/Over voltage Protection (n) Input Frequancy : 50 Hz

New generation energy saving and environmental friendly long life LED street light of 35 watt with high power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment and impact resistance of IK07 with High efficiency long life LED with SMD LED on MCPCB Powered by Built-in, isolated electronic LED driver (SMPS based constant current supply) complete making connection and testing after fixing, complete all as specified and directed by Engr-in-charge. The specification of light fitting should meet the following : - (a) Housing of Light fitting : Aluminium Die Cast (b) Diffuser : High efficient LENS Optics (c) Operating Voltage : Between 140 V- 270V (d) Operating Temperature : -10 to +50 Degree Centigrade (e) Lumen efficacy : Not less than 100 lm/W (f) System Lumens : Not less than 2500 lm (g) Colour Temperature : Not less than 5700K (h) Surge Voltage Protection : Up to 4KV (j) Ingress protection : IP 65 (k) Total Harmonic Distortion (THD) : Not less than 20% (l) Power factor : Not less than 0.9 (m) Line protection : Under/Over voltage Protection (n) Input Frequancy : 50 Hz

Taking down ceiling / exhaust fan, sealing cable end, dismantling blades and removing fan and blades to store, incl oiling, greasing, cleaning slot, overhauling & replacement of defective nut, bolt , washers etc. and applying two coat painting with synthetic enamel to fans complete, in situ by spraying including filling cavities with filler, one coat after cleaning all dust etc., making all connection using 1.5 sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose and rehanging/ refixing complete all as per the directions of Engr-in-Charge.

Supply and fix Exhaust fan, steel body AC single phase 230/240 V of size 300mm sweep with louver speed 900-950 RPM power input 50-55 W, Heavy duty, complete all as specified and as directed

Supply and fixing PVC body air freshner fan, copper windind, AC Single fsacses of size 150mm with louver including making necessary hole for fixing of PVC air freshner fan etc complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to and including 4mm dia galvanized iron wire lead by means of bolts, nuts, check nuts and washers of galvanized standard iron or steel all as specified or indicated in electrical plate No 3 of MES Part-I, including testing on completion including the material and labour and taking out old unserviceable earthing of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified.

Srl item No 145 Contd … (e) 15 mm nominal bore light grade GI protection pipe 7.5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.

VTPN distribution board when MCCB 125 Amps, 16 KA ( as incommer) 4-way, including MCB 125 Amps SPN, with IP-43, IK-09 protection 415V, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications ,fixing in repairs complete all as specified and as directed

Supply and fixing in repairs MCCB 4 pole, 415 volts 160 Amps with breaking capacity 36 KA " C" Curve complete all as specified and as directed.

Sheet metal enclosures for distribution board when MCB to be used SPN 8 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications ,fixing in repairs complete all as specified and as directed. (Note: MCBs will be measurd separately).

Supply and fix sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20Amps, 240V complete with one single pole MCB of any cap from 5 to 32 Amps of breaking capacity 10KA, complete all as specified and as directed

MCB SPN, 32 to 40 Amps,240 Volts, rupturing capacity 10 KA "B" Series including providing aluminuium thimbles for outgoing cable fixed in repairs, complete all as specified and as directed by Engr-in-Charge. Note : The exect capacity of MCB shall be as directed.

MCB SP, 6 to 32 Amps, 'B' series 10 KA 240 Volts including providing aluminuium thimbles for outgoing cable, complete all as specified. Note : The exact capacity of MCB shall be as directed.

MCB SP, 63 Amps, 'B' series 10 KA 240 Volts including providing aluminuium thimbles for outgoing cable, complete all as specified. Note : The exact capacity of MCB shall be as directed.

Taking down old serviceable/unserviceable Electric meter including meter box from existing position carefully refixing including making good to disturbed surfaces , complete all as specified and as directed.

Re-fixing only,serviceableElectric meter including meter box complete including minor repair to existing fitting occure while dismentling, complete all as specified and as directed.

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 6 Sqmm (1x6sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 6 Sqmm (1x6 sqmm ) cable and one metre of conduit will be measured as one unit.

Sub main wiring with two runs of 4 Sqmm ( 2x4 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 4 Sqmm (1x4sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, complete all as specified and directed. Note:- 2 runs of 4 Sqmm (2x4sqmm ) ,one run of 4 Sqmm (1x4 sqmm ) cable and one metre of conduit will be measured as one unit.

XLPE insulated sheathed armoured heavy duty LT 1100 Volts grade cable with aluminum conductors laid in trenches/pipe, fixed to poles, walls of size 25 sqmm 4 core and testing, including taking down of old cable, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, and for laying of cable or pipes etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and as directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil,complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed.

Double walled corrugated (DWC) pipe of HDPE, PE-100, PN-4 confirming to IS-14930 (Part-ll) alongwith necessary snap fit coupler for interconnection suitable protection of LT cable complete all as specified & directed.

Preparation of soil/ground by uprooting grass/vegetation etc, removing boulders, bebbles etc observed in the earth, leveling the surface flat or in slope at site, complete as specified and directed.

Planting of wild/local grass in the prepared surfaces (incl cost of grass) vide ser item No 163 above, watering upto the healthy growth and further germination complete all as specified and directed.

Supply and planting well grown disease free plants (including cost of plants/trees/shrubs) as appended below including preparing beds not less than 45 cm dia upto a suitable depth from the adjoining ground level and watering for suitable period of time till its healthy growth and further germinations completed all as directed by the Engr-in-Charge and as specified:-

(a) Bottle palm (3-4 Feet tall)

(b) Mor Pankhi (3-4 Feet tall)

(c) Duranta (3-4 Feet tall)

(d) Amaltas (3-4 Feet tall)

(e) Christmas tree (3-4 Feet tall)

(f) Bouganvilea (3-4 Feet tall)

(g) Gulmohar (3-4 Feet tall)

(h) Kachnar (3-4 Feet tall)

(j) Jacranda (3-4 Feet tall)

(k) Silver Oak (3-4 Feet tall) Note-:Cost of good earth/manure etc,watering etc shall to be included in the rates of ser No. 164 & 165.

S&F mild steel tree guard of size 2ft x 2ft x 5ft high Each made up of angle iron frame jali (mesh) as per the sample kept in GE's office and fixed in position with PCC including necessary excavation and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Manning for maintenance of plants/trees, grass lawn and flower beds /hedges etc by deploying well experienced mali 1 No per day from 0800 hrs to 1700 hrs including watering, replacing dead plants & removing wild weeds etc per complete (attendance of mali will be maintained by AGE's office). Notes:- The cost of replacing dead plants is deemed to include in the rates quoted by the contractor.

vmd traders (BID ID -3455704)