PERIODICAL SERVICES AND MISC B/R REPAIRS IN ZONE-II AREA UNDER AGE B/R-II OF GE JAIPUR

Amount

Taking down cement plaster or cement lime plaster on brick, stone surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc complete all as specified & as directed.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers, 1st layer 10 mm thick in CM 1:4 and IInd layer 5 mm thick in CM 1:4 incl mixing of WPC as per manufacturers instruction, on fair faces of brick masonry surfaces or concrete surface, finished even and smooth without using extra cement including necessary scaffolding arrangements up to any height complete all as specified and as directed. Note : WPC Shall be measured and paid seperately

Supply only integral water proofing compund ISI marked complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface of ceiling, chajja etc finished even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal exising treatment on old plastered surfaces of wall by mechanical means thourughly wetted surface to ensure better sticking including sand paper gentle rubbing to obtain smooth surfaces, including all necessary arrangement for execution of work, preparation of surafce and applying two coat of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller complete all as specified and directed .

M&L for preparation of newly plastered surface of walls and applying two coats of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints complete all as specified and directed .

M&L for preparation of old decorated plastered / unplastered surfaces of walls, soffits of chajjas, cornices etc and applying one coat of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller complete all as specified and directed .

M&L for complete removal of existing treatment by mechanical means on old plastered surfaces of walls, including cleaning of any mortar drops, fungus efflorescent salts etc, preparation of surfaces and applying two coats of distemper with distemper oil emulsion white or tinted complete all as specified and directed.

M & L for preparation of new plastered wall surfaces and applying two coat of distemper oil emulsion of approved tint over and including priming plastered surfaces with alkali resistant priming paint complete all as specified and directed .

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceiling and applying two coat of distemper with distemper oil emulsion white or tinted complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparation of old decorated surfaces of ceiling including brooming down and cleaning the surface and applying one coat of white wash complete all as specified and directed

M&L for complete removal of existing treatment by mechanical means on old plastered surfaces of walls, including cleaning of any mortar drops, fungus efflorescent salts etc, preparation of surfaces and applying two coats of cement base paint complete all as specified and directed

M&L for preparation of old decorated plastered / unplastered surfaces of walls, soffits of chajjas, cornices etc and applying one coat of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment on old decorated surfaces of walls, pillars and cornices and applying two coat of white wash complete all as specified and directed.

M & L for comlplete removal of existing treatment old plastered or unplastered decorated surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for preparation of old painted surfaces of wood or wood based materials of any description ot otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified & as directed.

S&F in repair 3mm thick Sheet glass, ordinary quality and glazing with and incl silicon in square n.exc 0.5 Sqm in each pane including hacking out old broken glass (any thickness, size, quality, or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window or door complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed.

M&L for coloured jointfree non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for coloured glazed ceramic tiles 450mm X 350mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for double charge/ultra charge vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.72 sqm but not exc 1.50 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed.

M&L for double charge/ultra charge vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.72 sqm but not exc 1.50 sqm, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including refixing all fittings complete all as specified and directed

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing in SSR complete all as specified and directed

Providing and Fixing Channelled perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 13mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.6. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Manufacturer and approved by the Architect/ Engineer-in-Charge. The panel shall be mounted by tongue and groove mechanism using inside clip on aluminium extruded keel made of Grade 6063-T5 having dimensions 3000(L) x 24(H) x 15.5(W).The keel shall also be used for transition of the butt end of adjacent panel at every 7.2m. INSTALLATION:An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface for fixing Keel. Install Keel vertically using screws and plugs at spacing of not more than 600mm centre-to-centre. The first and last keel should not be more than 150mm from the ends. Trim the tongue of the first bottom panel and install using headless nail with groove side upward. Subsequent panels are installed with tongue side downward by engaging with each other using tongue and groove mechanism and secured by inside clip. Continue this process until required height is achieved. Shorter butt edges need to be joined using industrial/wood glue complete all as specified and directed

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/false ceiling /slabs/ blankets, any thickness, including cover fillets and framing complete all as specified and directed

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with 15mm thick Sierra OP Tegular 15/90 Edge Tiles with Suprafine 15mm face exposed grid. The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 25db as per ASTM E1414, Light Reflectance ≥86% as per ASTM E-1477, Thermal Conductivity k = 0.040 W/mK, Colour Global White, Fire Performance of class A2-s1, d0 according to EN 13501-1 with 15mm Tegular 15/90˚ edge and 8mm drop in module size of 600 x 600mm. The scrim on the face of the tile shall be cleanable and classified as ISO 14644-1 cleanroom class 5. It shall be suitable for Green Building application, with Recycled content of 43%. The tile shall have Environmental Product Declaration as per ISO 14025 and EN 15804+A2. SUSPENSION: The tile shall be laid on Suprafine 38 with 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. All border cross tee/main beam shall be levelled using perimeter fill. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using KCS suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. All border cross tee/main beam shall be levelled using perimeter fill. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum Installation shall be carried out as per KCS recommended procedure. SUSPENSION SYSTEM accessories consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with light Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.55 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability.INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Supply and fix Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with and incl MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing & fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with and incl stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk with steel screws incl fixing 1.5mm thick decorative laminate type-1 of surface finish, colour and pattern as approved by engr-in-Charge and fixing with approved adhesive as per manufacturers instruction all as directed by Engr-In- Charge.

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVCextruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Providing and fixing factory made uPVC white colour Sliding window Three track (Area not exceeding 2.00 sqm each) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories for fixing of window complete all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S &F 4.8mm thick tinted glass ordinary quality and fixed in uPVC doors in sqaures exc 0.5 sqm in each pane complete all as specified and directed.

S &F 4mm thick tinted glass ordinary quality and fixed in uPVC window & Ventilator in sqaures n exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair automatic soap Dispenser, 265 X 118 X 110mm size, 0.8ltr capacity and fixed chromium plated brass screw complete all as specified and directed by Engr In Charge. Make : Jaquar cat part No. : SDR-BLC-DJ0160ASN or equivalent in Parryware roca or kohler as approved by GE

S&F in repair toilet paper holder complete all as specified and directed by Engr In Charge Make Jaquar, cat part No. ACN – CHR -1153S, or equivalent in Parryware roca or kohler as approved by GE

S&F in repair counter top wash hand basin of size: 495x395x150 mm incl waste coupling, bottel trap, divertor/concealed body, exposed part of wall mounted single lever basin mixer and other connected accesosories complete all as specified and directed by Engr In Charge Make : Jaquar, cat part No. JDS – WHT -25909 for WHB, Cat part No. ALD-CHR–233N for concealed Body for Single Lever wall mounted Basin Mixer, cat part No. OPP-CHR-15233NKPM for exposed part of wall mounted single lever basin mixer, cat part No. ALD CHR 705L130 for waste Coupling, cat part No. ALD CHR 769L 300X190 for bottle Trap or equivalent in Parryware roca or kohler as approved by GE

S&F in repair chromium plated tubular towel ring included new chromium plated brass screws & plastic rawl plug complete all as specified and directed by Engr In Charge. Make : Jaquar, CAT Part No.ACN-CHR-1121N or equivalent in Parryware roca or kohler as approved by GE

S&F in repair 15 mm angle/stop valve, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed for iron pipe or for unions complete all as specified and directed. Make : Jaquar CAT Part No. OPP CHR 15053PM or equivalent in Parryware roca or kohler as approved by GE

S&F in repair Corner glass shelf incl chromium plated brass screws complete all as specified and directed. Make : Jaquar, CAT Part No. ACN- CHR 1173 or equivalent in Parryware roca or kohler as approved by GE

S&F in repair vitreous China wall hung EWC, white with concealed cistern, concealed stop cock, switch plate and connected accessories incl connection complete all as specified and directed by Engr In Charge Make : Jaquar CAT No. OPS-WHT-10953B1UFSM for WC and Cat No. JCS-WHT-2431 FP for single piece concealed cestern or equivalent in Parryware roca or kohler as approved by GE

S&F in repair 15 mm bore two way bib tap, cast copper alloy chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed incl health faucet with flexible tube & Hooks incl making connection complete all as specified and directed. Make : Jaquar, CAT Part No. ALD CHR 573 for health faucet and cat part No. OPP CHR 15041PM for two way bib tap or equivalent in Parryware roca or kohler as approved by GE

S&F in repair 15 mm size PVC connections of length 600 mm with PTMT nuts complete all as specified and directed.

S&F in repair rectangle wall mounting mirror of size 18 X 24 inch with integrated LEDs for illumination, typically installed around the frame or behnd the glass, these energy efficeient mirrors provide enhanced lighting for personal grooming and makeup application by reducing shadows and are often available with features like antifog technology, adjustable brightness etc complete all as specified and directed.

Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

Taking down eaves gutters, sanitry PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S & F in repair 100mm dia outlet cast iron floor trap with grating including jointing to wastage pipe fixed in cement concrete 1:2:4 type B-1 and removing of old trap any type and shape complete all as specified and directed.

S&F in repair 100mm dia CP stainless steel grating including jointing with solvent cement complete all as specified and as directed.

M & L Dismantling/ chipping of unsound weak/ loose & cracked concrete/ cement plaster as in soffits of chajjas, ceillings, roof projection etc and cleaning the rusted reinforcement and exposed surface by wire brush, mechanical device or any other established method and applying the rust removing solution of approved make and quality with cotton swab to reinforcement and allowing to dry the same for 24 hrs, brushing of loose particles with wire brush and washing with water and applying bond coat of epoxy bonding agent, while epoxy is wet /tacky spread the fiber net of 80 gsm as reinforcing layer maintinting overlap of 5 cm at seams on damaged surfaces and applying polymer modified mortar having 20 mm avg thickness complete all as specified and as directed. Note :- Repairs to be done by authorised applicator of Asian paint/Dr Fixit/ Fosroc/Pidilite /sika as approved by GE.

Dismantling wrought iron or mild steel, including gates work of any description not otherwise provided for complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe410-W(Gde E-250) Quilaty A complete all as specified and directed.

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks (using old size bricks), straight or curved on plan exc 6m mean radius built in In cement mortar 1:6 complete all as specified and directed

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid bedded and pointed in any mortar complete all as specified and directed .

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for water proofing treatment on roof surface carried out as per following: (i) Surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and applying algae remover to clean all the algae and washing with water (ii) making v groove of crack surface and filling with with polymer modified mortar and plug with PU sealent, repair fine cracks by grouting of diluted coat of latex SBR mixed with water as per manufacturers instruction, repairing of Side gola if any (iii) Applying First coat of primer Latex SBR bonding agent mixed with cement in specified ratio as per manufacturers instruction. (iv) While primer coat is wet, spread the fibre net of 45 gsm as reinforcing layer on primer coating layer and embeded with maintaining overlap of 5 cm at seams (v) Applying second coat of LATEX SBR mixed with cement and water as per manufacturers instruction. (vi) Applying diluted coat of highly elastomeric, UV resistant, single component acrylic waterproof coating of high elongation and 8 degree temperature reduction duly followed by second and third Coat as per specified interval between the coats as per manufacturers instruction complete all as specified and directed. Make:- Asian paint -SmartCare Damp Proof Ultra, Berger-HS Roof Kool & Seal, STP-ShaliUrethane® BTD Plus) Note : (i) Work shall be carried out through authorized applicator of manufacturers only (ii) Material shall be used as per technical data / instruction of manufacturer after written approval of garrison engineer before execution at site and contractor shall submit guarantee of roof treatment work for TEN years

Note:- (a) 50% qty of material reqd for periodical services in this contract shall be procured in advance in seal packed container or bags after approval of the sample. (b) Material of required shade approved by Garrison engineer for the periodical work shall be procured in sealed container and will be opened in presence of Engineer in charge. (c) The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

JAGDAMBA CONSTRUCTION COMPANY (BID ID -3452838)

J.J.ENGINEERING (BID ID -3456995)

M/S MAYANK ASSOCIATE (BID ID -3462092)

Satish kumar and company (BID ID -3462814)