07 Webel IDM IT Park HWH MiscCivil 21 22 06

Amount

Brick work with 1st class bricks in cement mortar (1:4)

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in superstructure

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]

Plastering 15mm

Plastering 20mm

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor).

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. Two coats

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer

Supply fitting fixing 2 track Aluminium sliding window including glass & all supporting accessories.

Supply & fixing 100 mm Vertical blinds including all necessary fittings.

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in any floor as per relevant IS codes.

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (Fe 500)

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joints, angle, channel hollow sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection including all complete. The rate includes the cost of rolled steel section,priming coat, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.

Supplying, fitting & fixing polycarbonate sheet of approved make & brand conforming to IS: 14443-1997 and having 50 micron UV protection layer under co-extrusion technology, Fire rating being B-s1 as per EN13501-1 certification, fitted and fixed with 60mm wide aluminium channel section top and bottom member in dry-glaze sandwitch system, (unit wt. of top and bottom members: 0.375 kg/m & 0.69 kg/m) of approved brand and profile, EPDM quality rubber gaskets, anti dust tape, end closer "C" channel and 75 mm long Self tapping screw being drilled through the centre leg of the bottom section with nuts placed at 300 mm apart without anyway puncturing the polycarbonate sheet, EPDM Washer 16 mm dia & 3 mm thick washer etc complete strictly as per manufacturers specification and direction of Engineer-in- Charge. (Payment to be made on area of finished work) . with 2 wall 6 mm overall thickness ( wt.1.30kg/sqm,Ugvalue being 3.7 W/m2K, Min. cold bending radius of 900 mm). As per direction of EIC.

Supply fitting and fixing aluminium Al glazed Door with floor spring, handle, locking arrangement including all accessories

Providing thermocal or similar type material under roof sheet for heat resistance purpose only. Such material shoud be fixed properly with roofing sheet by nylon wire and bitumen adhesive . Minimum thkness will be 40 mm

Dismantling all types of masonry including cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 250 mtr.

i) Surface Preparation : Step 1 = Cleaning of concrete surface to remove dust, oil, grease including removal of laitance. Step 2 = Construction joint should be located and any shrinkage cracks (if any) should be identified. Step 3 = The construction joint and the shrinkage cracks should be grouted with NSPG and sealed. Step 4 = The joints between the parapet wall and the slab should be sealed by pointing with 1:1 cement sand mortar and cured for 2 days. ii) Skirting joint treatment: Step 5 = Cutting the skirting joint up to 20/10 mm in a v group shape . Then the trip portion fill with the polymer modified mortar. Wall up to 300 mm treated with polymer modified mortar. Patched the surface properly & treated the joint with v groove cutting & followed by mortaring.

Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. bracketsWash basin with stand …………….630 mm X 450 mm in size

Supply fitting & fixing CP Bib cock 20 mm dia

Supply fitting & fixing CP Angular Stop cock 20 mm dia

supply fitting & fixing cpvc 20mm pipeline including all fittings.

supply fitting & fixing waste pipe 32 mm

supply fitting & fixing 100mm pvc pipe

supply fitting and fixing cafeteria Dining table & Bench set

Supply installation of adjustable CRC sloted angle rack approx 2100mm height x 350 mm depth . Easy installation, Helpful in minimizing the storage space & cost, Robust & Durable, High Grade Oil Paint Construction, Number of shelves: 4, Gauge: 20 Gauge, Material: Prime CRC Sheet, Sales package: 1 Standing Shelf Unit,colour will be as per approved specification.

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary

Malasian Wood work in post, furniture, door frame, beading etc including a protective coat of painting at the contact surface .

supply installation of Partly glazed UPVC partition wall , 6mm thk toughned glass,frame thickness 20mm with door all necessary fittings including all as per approved design

Providing and fixing at all height false ceiling of 4mm thick phenol bonded Bamboo Mat board (595x595mm) conforming to IS:13958-1994 including providing and fixing of frame work made of GI angle 25x25x0.4 mm thick all around suitably fixed to wall with the help of dash fastener and hanger frame (600x600 c/c) made GI slotted Tee having powder coating on bottom side (30x25x0.3 mm thick for main member & 25x25x0.3 mm for cross member) connected to ceiling with 2.64mm GI wire and anchor fastener at every junction and also including cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed all complete as per direction of Engineer-in-charge

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping]

12 mm ply

19mm ply

6 mm ply

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge. The rate includes the cost of labour,

Medium Back Staff Chairs For Workstations : Providing and installation of Gale Mid Back chair with synchronized tilting mechanism with singlei-point locking systems with weight release, mesh for back and seat in fabric, adjustable back tilt and pneumatic seat height adjustment, Polypropylene Fixed 'T' arms, Black Nylon Base with 5 star black nylon base with castors with adjustable lumbar support

Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed erpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value > 0.65 should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge.Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U- 1520).

French polishing to wood work including preparing surface (ordinary gloss)

Suplly Fitting & Fixing pre coated/colour coated GI Sheet for roofing,wall etc. including all necessary fittings,staging but excluding cost of frame work . Asper direction of EIC

Supply fitting fixing key board tray,CPU trolley and wire manager for each seating of workstation including all necessary fittings .Payment will be made per seating.

Supply fitting fixing auto hinge/self closing hinge for furniture like cabinet etc.

Supply fitting fixing D type handle for furniture like drawer, cabinet etc.

Supply fitting fixing lock for furniture like drawer, cabinet etc.

RAJAN INFRATEC PVT. LTD.

LABARD INSTRUCHEM PVT. LTD.