SPL REPAIR TO AWPO OFFICE OF STN CELL REPAIRS TO CUPBOARDS OF KITCHEN IN OFFRS QTRS AND REPAIR TO BOUNDARY WALL NEAR GUEST ROOM EMERSION ROAD AT DANAPUR CANTT IN AGE BR II UNDER

Amount

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed

M&L Brick work (Except Brick) with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed

M&L rendering 15 mm thick on fair faces of brick wall in cement mortar (1:6) finished surface even and smooth without using extra cement, complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified and directed.

M&L for preparation of newly plastered surface of wall applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thicknesses, below or above ground level, complete all as specified and directed.

Dismantling of floor, walls, roof tiles including bedding but backing and rubbish off permises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm in floors etc. set and joining in neat cement slurry and pointed in coloured cement to match with shade of tiles , including laid over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramics coloured tiles of size 450x300x 7mm thick in vertical surfaces such as on skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces including 10mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified & directed.

Dismantling wall and ceiling board (fiber, pulp, PVC, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets complete all as specified and as directed.

S &F for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, size of grid 605mm x 605mm complete all as specified and as directed

S&F for hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40X30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

M&L for 6 mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber / GI / Aluminium framework with screws complete all as specified and as directed

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

All as per above item No 16 but exc 1.5 Sqm but n.exc. 4 Sqm each..

S & F powder coated aluminium door shutter (Double or Single) with following specification:- (a) chowkhat frame of size 114.30 x 44.45 x1.29 mm @ 1.139 Kg/RM (b) Style/Vertical member of size 47.62 x 44.45 x 1.90 mm @ 0.991 Kg/RM (c) Top and Middle rail of size 47.62 x 44.45 x 1.90 mm @ 0.991 Kg/RM (d) Bottom Rail of size 114.30 x 44.45 x 1.80 mm @ 1.6 Kg/RM (e) Partialy 9mm thick prelaminated particle board both side decorative (f) Partialy 5 mm thick tinted glass. (g) Aluminum and PVC beading as per requirment as in fixing for paticle board & Glass. (h) Two No.Disk Type Aluminium handle 200 mm long. (i) One No. Mortice lock and joing cleat. complete all as specified and directed .

M&L for double action floor spring hydraulically regulated made up of minimum 1.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S & F powder coated aluminium window sliding shutter three track with following specification:- (a) chowkhat frame of size 92 x 31.75 x1.20 mm @ 0.856Kg/RM (b) Style/Vertical member of size 39 x 20 x 1.0 mm @ 0.342 Kg/RM (c) Top and bottom rail of size 39 x 20 x 1.0 mm @ 0.342 Kg/RM (d) Partialy 0.63 mm dia stainless steel wire netting mosquito proof with fixing arrangment. (e) Partialy 5 mm thick tinted glass fixing with rubber gasket. (f) Aluminum and PVC beading as per requirment as in fixing for paticle board & Glass, joing cleat including locking arrangement. etc complete all as specified and directed .

S&F powder coated anodized aluminium grill (diamond shape of approx size 100x100mm) made out of aluminium flat of size 4x5mm as approved by Engr-in-Charge/GE for window/ ventilators etc complete all as specified & directed.

S&F Solid PVC door frame of size 50mm x47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S & F 28 to 30 mm(stiles) Factory Made Solid PVC Moulded door shutter with particle board core , with 2, 3 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, in frame at site as per specification & drawings as given in SSR part - II (2010 print) on serial page No. 161 complete all as specified and directed.

S&F Butt hinges (ISI marked), medium weight, cold rolled mild steel of size 100 mm complete all as spd and as directed.

S&F 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F Aluminium handles, cast type, anodized 150 mm size ISI Marked complete all as specified and directed.

S & F aluminium alloy anodised, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy size 250 mm large complete all as specified and directed.

Taking up or down of 15 mm dia steel tubing and connections complete all as specified and directed .

Taking up or down of 20 mm dia steel tubing and connections complete all as specified and directed.

S&F Tubes, of 15 mm dia ‘medium grade’ galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors including cutting /chasing in walls etc complete all as specified and directed.

S&F Tubes, of 20 mm dia ‘medium grade’ galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors including cutting /chasing in walls etc complete all as specified and directed.

Cutting chases in brick wall, etc for concealed water tubing ,etc & making good in CM 1:3 , cutting not exc 10 cm girth complete all as specified and directed.

S & F in repair 20mm dia gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repair 450mm long PVC connection of size 15 mm with PTMT nuts etc complete all as specified & directed.

S & F as in repair 15 mm dia angle cock, chromium plated, cast copper alloy, fancy type, screwed down high pressure with capstan head screwed both ends for iron pipe or for union complete all as specified and directed.

S & F as in repair 15 mm dia bib taps chromium plated cast copper alloy fancy type, long shank with capstan head screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Taking down CI/PVC/AC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100/75 mm dia pipe complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc complete all as specified and directed.

S&F PVC (SWR) bend/shoes any radius of 110 mm dia complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl of 110 mm dia complete all as specified and directed.

S&F 75 mm bore PVC (SWR) floor trap, plain with grating including jointing to waste pipe, complete all as specified and directed.

S & F in repairs vitreous china urinals, half stall type , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair vitreous china wash hand basin size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete all as specified and directed.

Supply and fixing in repair 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated , screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F Toilet paper holder complete all as specified and directed.

S&F CP soap dish of standard size as approved complete all as specified and directed.

S&F as in repair vitreous china wash down water closet pan(pedestal pattern), white including white seat cover ( excluding flushing cistern and flush pipe) complete all as specified & directed by Engr-in- Charge.

S&F in repair PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed .

Dismantling water tanks of capacity exc 250 and n exc 500 ltrs complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 500 Ltr capacity including CP tank nipple complete all as specified and directed.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

Taking down old wooden/wood based particle board & S&F 18/19 mm thick high density PVC solid fibre board duly laminated 2mm thick prelaminated PVC sheet on front face (ISI mark) etc in kitchen cupboard etc.

S&F 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete all as specified and directed

S&F 100 mm dia extruded brass handle, fabricated type polished fixed to board complete all as specified and directed.

S&F 2 liver brass cupboard lock grade-I size 65mm etc complete all as specified and directed.

Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft / loose of soil complete all as specified and directed.

Boring holes 3m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

M & L for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, coping, lintels over 1.5 m sapn and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L rendering 15 mm thick on other than fair faces of brick wall in cement mortar (1:6) finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed .

M&L for two coats of weather coat paint on newly plastered surfaces over a coat of primer including preparation of surface complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 50 m but not exc. 250m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for 15-17 mm thick machine cut pre-polished granite stone slab as in skirting / dado, laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab over and including 10 mm thick on backing coat in CM 1:4 complete ,including necessary cutting, grinding, rubbing, polishing rounding to exposed edges complete all as specified and directed.

SINHA CONSTRUCTION