REPAIR REPLACEMENT OF BARRACKS SHEDS AND OTHER TEMP ACCN UNDER BR II UNDER GE NW NOFRA COLABA MUMBAI

Amount

Taking down cement plaster, any description on brick or stone walls and ceiling including racking of joints hacking for key scrubbing down with water etc for storey upto GF to sixth floor incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

M&L for 20mm thick plastering in cement & sand mortar 1:4 in 2 coats (15 mm thick backing coat and 5 mm thick setting coat mixed with water proofing compound) on fair faces of brick work or stone masonary surfaces, finished even and smooth (w/o using extra cement) all as specified and directed (WPC shall be mesured and paid seperately) incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

M&L for 15mm thick plastering in cement & sand mortar 1:6 on fair faces of brick work or stone masonary surfaces, finished even and smooth (w/o using extra cement) all as specified and directed (WPC shall be mesured and paid seperately) incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

Preparation of new plastered surfaces of walls and applying two coats of acrylic emulsion exterior grade (100%) over a coat of primer incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of 1 to 2 mm thick wall care putty complete all as specified and directed by Engineer in charge.

Supply only integral water proofing compound as per IS 2645 complete all as specified and directed by Engineer in charge.

Preparation of old decorated surfaces of walls and applying one coat of acrylic emulsion exterior grade (100%) incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer in charge.

S& F for Framed work such as grills,angle iron, posts, pipe sections, railings etc. with ends of bars shouldered and/or riveted, or forged into spikes; door shutters with gusset plates, braces, etc., to be prepared for hanging or sliding with and including eitherr hooks and hinges or steel hanging door fittings and similar work con- forming to Fe.290.Gde-E-165 at any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

M&L for 1.25 mm thick mild steel, plain, black sheet as in steel door shutters cut to size and welding to angle iron framework in repairs complete all as specified and directed by Engineer in charge..

M&L for preparation of new steel surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

M&L for preparation of old steel surfaces of any description and applying one coat of synthetic enamel paint incl all necessary scaffolding etc complete all as specified and directed by Engineer in charge.

S & F in repair for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer in charge.

S&F in repair for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws in repair, complete all as specified and directed by Engineer in charge.

M&L for 75mm thick PCC 1:2:4 (20mm graded stone aggregate) as in flooring finished with even and fair without using extra cement incl necessary formwork and demolition of old concrete complete all as specified and directed by Engineer in charge.

M &L for 80 mm thick interlocking paver block machine pressed of any size and shape as approved by GE incl 50mm sand cushion and demolition of old paver blocks and removal to store complete all as specified and directed by Engineer in charge.

Demolition of brick work/ stone masonary built cement mortar complete all as specified and directed by Engineer in charge.

M&L Brick work with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar,complete all as specified and directed by Engineer in charge.

M&L for Polished granite stone slab 20mm thick (table rubbed and polished) in steps, jambs, pillar, window cills, cooking platform and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture pigment to match with shade of granite including moulding at front edge complete all as specified and directed by Engineer in charge as in platforms Note : Quality of granite all as approved by GE .

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MD land complete all as specified and directed by Engineer in charge.

M&L for DGVT vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tiles not exceeding 0.36 sqm including over 15mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by the Engineer-in-Charge Make: Somany, Kajaria, Orient bell.

M & L for DGVT vitrified ceramic tiles light shade 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm but as on veretical surfaces such as skirting /dado including 10mm thick backing layer of CM 1:4 for laying floor finishes on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by the Engineer-in-Charge

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick(square/Rectanglar) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floor including 20mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer in charge.

M&L for coloured glazed ceramic tiles 450x300x7 / 350x250 x7 mm mm thick but as on vertical surfaces such as skirting/dado including 15 to 20mm thick backing coat in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer in charge.

M & L for Metal frame suspended 12.5mm thick gypsum false ceiling size 600mm X 600 mm including metal perimeter channel of size 0.50mm thick(having one flange of 20mm and another of 30mm and web of 27mm) along with the perimeter of ceiling, screw fix to block/brickwall/ partition with the help of nylon sleeves then suspending with metal intermediate channel of size 8.0mm thick with two equal flanges each 15mm from the sofit at 900mm c/c with help of sofit cleats and Rawl plug including dismantling of existing ceiling complete all as specified and directed by Engineer in charge.

S&F roof tiles, Mangalore pattern, interlocking at side joints, laid dry including dismatling of tiles complete all as specified and directed by Engineer in charge.

M&L for preparation of old wall surfaces and applying two coats of oil emulsion distemper complete all as specified and directed by Engineer in charge.

M&L preparation of old distempered surfaces of walls and applying one coat of oil emulsion distemper on walls etc complete all as specified and directed by Engineer in charge.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of oil emulsion distemper on ceiling complete all as specified and directed by Engineer in charge.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer in charge.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4.00 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer in charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each complete all as specified and directed by Engineer in charge.

S&F 35mm thick 2nd class HW rail & stile plain framed , panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer in charge.

S&F 35mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (b) ; supplied and fitted to chowkhats of Second class hard wood complete all as specified and directed by Engineer in charge.

M&L for preparation of newly wooden surfaes of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces complete all as specified and directed by Engineer in charge.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed by Engineer in charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per drawings complete all as specified and directed by Engineer in charge.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified and directed by Engineer in charge.

S&Fin repair powder coated (colour of coating as directed) aluminium (minimum 25 micron thickness of coating) of various section as required/suitable for doors, window & partion/Ventilator (sliding /or openable type)etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like jointing cleats, glazing clips, rubber neoprene packing. anodised aluminium snap beading screws etc. rubber beading, clips locking arrangement, handle, sealant etc complete all as specified and directed by Engineer in charge.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed by Engineer in charge.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed by Engineer in charge.

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed by Engineer in charge.

S&F 150 mm size aluminium alloy handles, cast type anodised, ISI marked complete all as specified and directed by Engineer in charge.

S&F 100 mm size aluminium alloy handles, cast type anodised, ISI marked complete all as specified and directed by Engineer in charge.

S&F butt hinges 100 mm stainless steel hinges medium weight and fixed complete all as specified and directed by Engineer in charge.

S&F butt hinges 75 mm stainless steel hinges medium weight and fixed complete all as specified and directed by Engineer in charge.

M & L for MS flat for hold fast. Conforming to Fe-310-0 or Fe-410-0 complete all as specified and directed by Engineer in charge.

S&F 150 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer in charge.

S&F 125 mm long hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer in charge.

Hacking out old broken glass (any thickness, size, quality or description) from iron frames glazed with putty or wooden beads complete all as specified and directed by Engineer in charge. (Note : Work carried out upto 16th floor of building either from inside or from outside)

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer in charge.

S&F 3mm thick sheet glass froasted or obscured one side and glazing with oil putty or wooden beads in square area n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer in charge. (Note : Work carried out upto 16th floor of building either from inside or from outside)

S&F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples incl wooden beading complete all as specified and directed by Engineer in charge.

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers , clips .,including taking down existing GI water tubing complete with all fittings of 15 mm bore, complete all as specified. Note : Quoted Rates shall include scaffolding upto 16th floor

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 20 mm bore fixed to walls or ceilings with saddles/spacers , clips .,including taking down existing GI water tubing complete with all fittings of 20 mm bore, complete all as specified. Note : Quoted Rates shall include scaffolding upto 16th floor

Taking down & Refixing 15mm old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed by Engineer in charge. Note : Quoted Rates shall include scaffolding upto 16th floor

Taking down & Refixing 20mm old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed by Engineer in charge. Note : Quoted Rates shall include scaffolding upto 16th floor

S&F 20mm bore of CPVC pipes having thermal stability for hot & cold water supply including all plain and brass threded fittings fixed of required sizes including with all fittings and fixed to wall /ceilings with suitable clamps, laid in floor or concealed of 20mm size (in high rise building (upto 16th floor)including scaffolding) and incl. taking down old tubes of any desc. complete all as specified and directed by Engineer-in-Charge. Make: Finolex / Prince/ Astral

S&F in repairs vitreous china wash down water closet pan white (pedestal pattern) including plastic sheet cover with nuts and bolts etc complete all as specified and directed by Engineer in charge.

S&F in repairs water closet squattin pan (Orissa pattern) 580x440mm, white with integral foot rests including connecting to trap and to flushing pipe antisyphonage pipe including making good to floor (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer in charge.

S&F vitreous china wash hand basin flat back of size 550x400mm including bracket, brass chromium plated waste coupling of 32 mm bore and pillar tap 15mm bore dia fancy type complete as fixed in repair complete all as specified and directed by Engineer in charge.

S&F 10 ltr capacity PVC syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specified and directed by Engineer in charge.

S&F in repairs CP bib cock 15 mm bore complete all as specified and directed by Engineer in charge.

S&F in repairs fancy type CP Pillar taps 15 mm bore complete all as specified and directed by Engineer in charge.

S&F in repairs CP angular stop cock 15 mm bore complete all as specified and directed by Engineer in charge.

Dismantling water tank of capacity exc. 250 Ltrs but n.exc. 500 ltrs complete all as specified and directed by Engineer in charge.

S&F rotational moulded polythylene water storage loft tank tank of 300 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I complete all as specified and directed by Engineer in charge.

S&F in repairs PVC modular section 20mm thick as in profile including 'C' channels, aluminium all around the profile complete all as specified and directed by Engineer in charge.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms) complete all as specified and directed by Engineer in charge.

S&F 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer in charge.

M&L for PCC 1:2:4 (20mm graded stone aggregate) as in copings, bed blocks, bed plates etc complete all as specified and directed by Engineer in charge.

NATH CONSTRUCTION

SAHU AND SAHU CO.