SPECIAL REPAIRS TO BLDG NOT-16,T-18, T-19 AND T-20 AT ATS BELAGAVI

Amount

Dismantling of Mangalore pattern or similar tiles in roof coverings including ridges compete all as specified and directed.

Dismentling of Battens for tiles, shingles etc, of any size including tilting fillets of spacing exc 15 cm compete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compete all as specified and directed. (Note :- The length of self tapping screw may vary for wooden and steel truss. Contractor to quote rate accordingly.)

M & L pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridges, roof overing/cladding to wall, fixed with self tapping screws compete all as specified and directed. (Note :- The length of self tapping screw may vary for wooden and steel truss. Contractor to quote rate accordingly.)

M & L for Mild steel work a in hold fast, wall ties,bands, straps or similar small articles conforming to Fe-290 Gde E-165 etc.complete all as specified and directed.

M & L for preparation of new steel surfaces of any discription, n exc 10 cm width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified.

Dismantling wall and ceiling boards (Fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets, frame work all as directed.

M & L for powder coated Aluminium snap grid (minimum 50 microns thickness powder coating) of size 605 x 605 mm with anodised aluminium angle of size 25mmx25mm x1.5mm thick and main & cross T of size 40mm x 25mm x 2.0mm thick for false ceiling including fixing of supporting hangers all as specified and directed Note :Cost of hangers will be measured & paid seperately under relevant items of this schedule

S & F Hangers 6 mm dia GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified.

S & F 12 mm thick Gypsum board of size 600 x 600 mm in ceiling fixed with screws and finished with two coats oil bound distemper over a coat of self primer all as per manufaturers instructions complete all as specified and directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc 40 sqcm and over in section in any position (unframed work) complete all as specified and directed.

Dismentling of framed wooden trusses span n exc 10 m of any discription complete all as specified and directed.

S & F Rolled Mild steel in Roof trusses (framed), trussed purlins, rails and fastenings and heavy brackets framing including distance pieces, cleats etc Fe 410-W (Gde E-250) quality B all as specified and directed

M & L Structural steel of plates, Fe-410 W (Gde E-250) Quality-B), channels, square cut or notched (ordinary or counter sunk) forming holes with riveted, bolted or welded attachments all as specified and directed

S & F of Rolled section having Fe 410-W (Gde E-250) quality B as in main and cross beams, hip and jack rafters: purlins where connected to common rafters and running rails and guids for sliding doors: fixed with angle cleats or other connecting plates all as specified and directed

Dismantling posts or struts (wood, steel or RCC) any section , including taking out embedded protion in concrete, brick work, and masonary etc and making good disturbed ground all as directed.

S & F of Steel tubular section for trusses/posts/purlins/rafters including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided compete all as specified and directed.

M & L Plain Cement Concrete 1:2:4 type B1 using 20 mm graded stone aggregate for embedding M S PIPES or similar work all as specified and directed.

M & L Cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in coping including necessary form work compete all as specified and directed.

M & L for preparation of old steel surfaces of any discription, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enemal paint complete all as specified.

Demolition of cement concrete in ground floor and pavings n exc 15 cm thickness (Below or above ground level) compete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises compete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B1 (Using 20 mm graded stone aggregate) as in floor finished without using extra cement compete all as specified and directed.

M & L for Joint free Non skid coloured tiles superior finish grade B-1 quality 7 to 8 mm thick(square/ rectangular) area of each tiles exc.0.18 sqm but not exc 0.38 sqm in floor with rectified edges etc set and jointed in neat cement slury over and including cement screed bed 15 mm thick in CM (1:6) compete all as specified and directed.

M & L for Coloured glazed ceramic tiles economy finish Gde B-II (b) quality of size 300 x 450 x 7 mm thick with rectified edges as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and incl 10 mm thick backing with CM 1:4 compete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick over and including cement screed base of 20 mm thick in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and polishing compete all as specified and directed.

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed 1:4, 10mm thick and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and polishing compete all as specified and directed.

Rubbing and polishing to existing kota stone incluidng waxing to remove all stain, dirts/soil marks etc. all as specified and directed.

M & L Cement concrete type B2, 1:3:6 (40mm graded aggregate) 75 mm thick as in plinth protection including finishing of concrete surface even and smooth without using extra cement and necessary form work complete all as specified and directed.

M & L for hard core of broken stone or boulders of gauge not exceeding 63 mm deposited spread and leveled in layers n exc 15 cm thick, watered and well rammed to a true surface complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring with 75mm thickness complete all as specified and directed.

M & L 100 mm thick PCC 1:2:4 type B1 (Using 20 mm graded stone aggregate) as in floor finished without using extra cement including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified.

M & L for forming contraction (Dummy) joints 65 mm deep x 10 mm wide, filled with seling compound Grade 'B' compete all as specified and directed.

Taking down of chowkats with shutters (without taking off shutters from the frames) n exc 1.5 sqm each all as specified and directed.

Taking down of chowkats with shutters (without taking off shutters from the frames) exc 1.5 sqm and n exc 4 Sqm each all as specified and directed.

Cutting holes in brick/stone/PCC block walls built in cement mortar exc ½ bricks but not exc one brick thick for fixing hold fast and making good dismantled portion in cement concrete 1:2:4, type B1 etc all as directed.

S & F 125 x 60 mm size Pressed steel frames for doors, pressed out of cold rolled mild steel sheets of 1.25 mm thickness as indicated and shall comply with requirements of IS 4351-2003, Specifications for steel door frames; with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S & F 30 mm thick second class hardwood rail & style plain framed pannelled shutter(any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

M & L 2nd class glazed and skeleton shutters, 35 mm thick open rebaed and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc; sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats compete all as specified and directed.

M & L Flush shutters 40 mm thick, solid core construction, with particle board core and plywood face panels, commercial type on both sides compete all as specified and directed.

M & L Painting and preperation of new wooden surfaces applying pink primer and two coats of synthetic enamel paint (ordinary tint) over 10cm width or girth all as specified and directed.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handles, steel tower bolts, steel peg stay and steel frame with glazing bars devetailed or welded complete all as specified and directed.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handles, steel tower bolts, steel peg stay and steel frame complete without glazing bars complete all as specified and directed.

Supply and fix sheet plain glass, ordinary quality, in squares n exc 0.5 sqm for each pane of 4 mm thickness all as specified and directed

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified

S & F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 compete all as specified and directed.

M & L for preparation of new steel surfaces of any discription, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified.

S/F 140 mm floor door stopper of aluminum alloy body and tongue,anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified.

S & F Butt hinges 100 mm long medium Weight cold rolled mild steel and fixed all as specified.

S & F for 300 mm long Aluminium alloy ,anodised sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet, cast of extruded section and fixing bolts and sliding bolts extruded sections or cast aluminium alloy and fixed.

Supply and fixed 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete in mild steel fixed to MS frame or wooden framed all as specified.

S&F 150 mm long extruded aluminium alloy anodised handle fabricated type all as specified.

Supply and fixing in repairs harrison rails, mild steel,chromium plated with fixing brackets, stops roller etc. all as specified and as directed.

M& L for cement concrete 1:2:4 type B-1 using 20mm graded aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating all as specified and as directed.

M & L for 18- 20mm thick green marble jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing polishing rounding to edges as in cills and similar works all as specified and as directed.

M&L for preparation of external old plastered surfaces of walls by complete removal of existing treatment including washing, rubbing and cleaning and applying two coats of antifungal paint over a coat of primer all as specified and directed.

M & L for preparation of external newly plastered surfaces of walls by cleaning and applying two coats of antifungal paint over a coat of primer all as specified and directed.

M & L for complete removal of existing treatment of old surface of wall by scrapping wand washing including perpration of surface by applying a thin layer of wall putty (JK or Birla) and applying two coat of oil bound distemper all as specified and directed

M & L for preparation of newly plastered surface of wall by cleaning and including prepration of surface by applying a thin layer of wall putty (JK or Birla) and applying two coat of oil bound distemper all as specified and directed

S & F in repairs for Plain mild steel wire, galvanised class 3 of 4 mm dia in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. all as specified and as directed.

Taking down cement plaster on brick or stone walls, celing etc incl raking out joints hacking for key, scrubbing down with water etc complete including removing rubbish off the premises all as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided all as directed.

M&L Precast cement concrete 1:2:4 type B1 (20mm agg) for cover Slabs (for man holes, drains etc) including necessary form work setting in cement mortar(1:4) as specified and directed

TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition of brickwork or stone/boulder/block masonary, build in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, all as directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified and as directed.

M & L PCC 1:4:8, type D-2 (using 40mm graded stone aggregate) as in mass concrete complete all as specified and directed.

M & L for pre cast cement concrete block masonry type C1, 1:3:6 (20 mm graded agrregate) solid blocks exc 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified

Rendering 15 mm thick cement plaster in CM 1:4 for fair faces of brickwork or concrete surfaces,walls finished even & smooth without using extra cement all as specified and as directed.

Rendering 10 mm thick cement plaster in CM 1:4 for fair faces of brickwork or concrete surfaces wall finished even & smooth without using extra cement all as specified and as directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds etc.complete all as specified and as directed.

Removal of concrete and plaster debris to a distance 5 Km and depositing where directed at a level n exc 1.50 m above the starting point complete all as directed.

Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar of size 300 mm and taking out of trenches, if required complete all as specified and as directed.

Material and laying of 300 mm Bore Hume pipe, Reinforced concrete pipes, class NP2, laid and jointed complete with collars all as specified and as directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 300 mm bore all as specified and as directed.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 all as specified and as directed.

Mild steel bolts, dia of neck exc 12mm n. exc. 20 mm purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long embedded in RCC complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as directed.

Taking down carefully unserviceable main switches/DB's off size from their position and removing materials from site all as specified and as directed by Engr-in-Charge

Taking down existing sub main wiring with aluminum conductor cable of 2 runs of 4/6/10 sqmm with GI earth wire on and including wooden batten and removing materials from the site and making good distrubed surface of walls and and roofs complete all as specified and as directed by Engr-in-Charge

Material and Labour for point wiring with PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable drawn in and including PVC casing capping 20/25 mm width complete with all accessories including 1.6 mm thick pressed steel terminal boxes with 3 mm thick plastic laminated sheet cover for fixing switch,socket ,regulator etc of suitable size to be fixed on wall respectively including white washing/colour washing/distembering to match the disturbed surfaces including PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable as earth continuvity connected with common earth dolly complete for One light point controlled by one, one way switch 5 Amp complete all as directed

All as per item No 83 above but for one fan point controlled by one, one way switch 5 Amp all as specified and as directed.

All as per item No 83 above but for one 3 pin switch socket outlet 5 amp independent all as specified and as directed.

All as per item Sl No 83 above but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for piont wiring and 2.5 sqmm as in contineous earth wire all as specified and as directed.

M&L complete for switch piano flush button single pole one way 5 Amp 240 V all as specified and as directed.

M&L for switch socket combination 2 in 1,3 pin 5 Amp flush type 240 volts complete all as specified

M&L for switch socket combination 2 in 1,3 pin 16 Amp flush type 240 volts complete all as specified

M&L complete for ceiling rose surface backelite three terminal 240 volts complete all as specified

S&F fan regulator, electronic, step type , flush mounting complete all as specified and as directed.

Supply and Fix REGAL Batten for LED tube with single LED Lamp 1x 20 w, Ultra bright glass LED Tubelight with very high efficacy suited for installation in T5/T8 fitting with lamp holders etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed Make & Model No for Batten :CROMPTON Cat No Regal LED Batten Cat No DIJB12LT8-20and LED Lamp LED Lamp Crompton Cat No LGT8-20-865-2 or equivellent model of other Make

S&F LED building security light made of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP-66 protection with SPD LED street light of 20 Watt all as cat part no .LSTS-20-CDL-M of Crompton make or equivalent make of Bajaj/Philips/Wipro/Havells.with sutable size bracket made to shape of 40 mm dia GI pipe medium grade of 1.4 mtr length including MS clamps 25 x 4 mm - 02 Nos with nut bolts washers all as specified and as directed.

Supply and Fix recessed type LED Light fitting 28 Watts of size 2 x 2 LED edge-lite luminaries suitable for armstrong/grid ceiling complete for low celing application with LED Drive of 28 Watts complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed Model No : Havells Cat No ENDURASLIMPROPLUS2X2PLR28/36WLED840MOD and Drivers Cat Part No. LEDDRIVER36V28WS or equivellent model of other Makes .

Sub main wiring with two single core stranded copper conductor unsheathed PVC insulated FRLS cable 1100V grade with 6 sq mm drawn through and including suitable size of non-metallic PVC rigid conduit/casing caping with one run 6 sqmm copper conductor FRLS cable as earth conductor and conduit accessories fixed up in surface/ recessed as required, including connecting up complete all as specified and directed. NOTE ;- Two runs of 6 sq mm cable and one run of 6 sq mm earth continuity copper conductor and one run of PVC conduit / casing caping shall be measured as one unit

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 12 Way complete all as specified and as directed .

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way complete all as specified and as directed .

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 4 Way complete all as specified and as directed .

S&F sheet metal enclosure factory made single door for DB 240 volts SPN 2 Way complete all as specified and as directed .

M&L complete for MCB SPN 10 - 32 Amps 240 volts, 50 Hz AC supply complete all as specified & directed incl taking down old UNSV one.

M&L complete for MCB SP 06 to 32 Amps 240 volts, 50 Hz AC supply complete all as specified & directed incl taking down old UNSV one.

M&L complete for MCB TPN 32 Amps 240 volts, 50 Hz AC supply including taking down old unserviceable complete all as specified & directed.

Taking down ceilng fan, dismantling blades and removing fan and blades to store, Painting of fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc and refixing ceiling fan and connecting up including provision of cable from ceiling rose or connector of fan all as specified and as directed.

Supply, installation, testing and commissioning of 1 KVA Isolation transformer, single phase, 50 Hz, copper wound, class of insulation A metallic body powder coated designed for Input voltage range 240 +2.5 % and output voltage range 240 + 2.5 %, ratio 1:1, vector group: Dyne 11, efficiency more than 95%, potential difference between neutral to earth less than one volt with all standard fittings, including wall mounted stand for fixing/ keeping isolation transformer indoor type complete all as specified and as directed.

M&L for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in Electrical Plate No 3 of SSR Part-I and testing on completion all as specified and as directed.

M & L for maintenance free chemical earthing Pipe in Pipe technology . Having 01 No GI Pipe in Pipe electrode length 3 mtr , Dia 76 mm filling with 2 Bags/ 60 Kgs EBFC chemical based ENNOV back fill compound or another equivalent compound incl construction of PCC pit and cover, earth lead protection pipe etc all as directed by engr-in-charge. Note-Copper strip will measured and paid seprately.

M&L for 20 x 3 mm Copper Strip for inter connection of earthings and to connect the earthing to the main panel .

Supplying, laying,saddling in wall by using suitable size saddle and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoure d,electric power cables (heavy duty )1100 volts grade with stranded aluminium conductor of size 10 sqmm x 2 core including taking down old unserviceable complete all as specified & directed.

Supply, laying, taking down and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured.electric power cables (Heavy duty) 1100 Volts grade with stranderd aluminium conductor of size 10 sqmm x 4 core including taking down old unserviceable complete all as specified & directed.

Excavation in trenches not exceeding 1.5m wide and 1.5m in depth for laying cables and getting out in hard / dense soil for laying cable/erecting poles all as specified.

Supply and spread river sand for cable cushioning in trenches all as specified in clause 19.75 of SSR Part-I, all as specified.

Supply and laying well burnt sub class B bricks old size bricks, laid flat dry, in trenches with width of the bricks laid to the axis of cable for cable protection complete all as specified and as directed.

Returning and filling in soil including spreading leveling watering and well ramming in layers not exceeding 25cm all as specified.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point.

GI pipes light grade galvanised with all fitting and fixed complete to poles/route/drains etc and ceillings or laid in floors of 50 mm dia complete all as specified and directed.

M/s. VIJAY ELECTRICALS

DHAIRYASIL RAMAKANT DESAI

Manak landmarks

Phoenix Infra

DHANSHRI ENTERPRISES

ASHIRWAD ELECTRICALS