PROVN OF HARDSTANDING FOR REPAIRING VEHICLES OF CERTAIN UNIT AT BHALUKMARA , SPL REP TO BLDG NO P-15A URO AND PROVN OF STORAGE SHED FOR MOB MT STORES AT CERTAIN UNIT OF SARAIBARI AT JORHAT MIL STN UNDER GE JORHAT

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil complete all as specified.

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n.exc 1.5m in depth; for foundation etc. n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out etc complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

Removing excavated materials (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

Earth ( excavated soil ) filling in floors etc including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

M & L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation , filling and mass or lean concrete etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Columns, pillars, piers,posts and struts etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Beams, cantilevers,bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Chajja etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports,overhangs,etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Formwork to chullah hoods, chajjas,troughs and similar items including edges etc. complete all as specified and as directed.

M&L for Formwork to sides of pillars,posts, struts, piers, columns and stanchions etc. complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter etc. complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate) as in floor finishing , finished even and smooth etc complete all as specified and as directed.

M&L for Brick work with sub class‘B’ bricks,straight or curved on plan exc 6m mean radius, built in cement sand mortar 1:6 etc complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement sand mortar 1:4 etc complete all as specified and as directed.

S&F mild steel work as in tubular trusses , purlins, and posts etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 5 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

S&F factory made Steel ventilator with top hung shutter including hinges, steel peg stay, complete etc complete all as specified and as directed.

S&F 35 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, and both faces shall be covered with decorative face veener with lipping / frame to match etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in fixing of holdfast and similar works etc complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section 200mm in length complete all as specified and as directed.

S&F aluminium anodised bow handles of 150 mm size with aluminium anodised screws, cast type etc complete all as specified and as directed.

S&F 3 mm thick, Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane etc complete all as specified and directed.

S&F aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,300 mm etc complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor , overall length of cover plate 150 mm etc complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:3:6) type C1 using 20 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement , complete all as specified and as directed.

M&L for Hardcore ( crushed stone ) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for 25 mm thick Damp proof course in cement sand mortar 1:2 mixed with intrgral water proofing compound @ 3% by the weight of cement ,applied to horizontal or vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and as directed.

S&F factory made pressed steel frames 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc. complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded including cutting holes in old concrete / brick wall and making good in cement sand mortar 1:2 or PCC 1:2:4 type B-1 using 20 mm graded stone aggregate after fixing of windows etc complete all as specified and as directed.

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of on new wooden surface, over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer etc complete all as specified and as directed.

M&L for Rendering 15 mm thick cement plaster in cement sand mortar (1:6) on fair faces of brick work or concrete surfaces , finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 15 mm thick cement plaster in cement sand mortar (1:4) on other than fair faces of brick work or concrete surfaces , finished even and without smooth using extra cement complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash etc complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over and including a coat of alkali resistant primer etc complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting , any gauge,thickness, including nainital or similar pattern etc complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-290 (Gde E-165) complete etc complete all as specified and as directed.

Material and Labour for applying one coat of synthetic enamel paint on old or previously treated surfaces of steel and iron exceeding 10 cm in width or girth including necessary preparation of steel surfaces complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removing debris from site etc complete all as specified and as directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate) as in floor finishing , finished even and smooth etc complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed.

M&L for preparation of old surfaces of walls including scraping down smoke spots, moulds, moss and efforescent salts and trading oil and greasy spots etc including cornices, pilasters etc and applying one coat of white wash etc complete all as specified and as directed.

M&L for preparation of old surfaces of walls including washing , rubbing down and stopping of distempered and painted surfaces and applying one coat of cement base paint etc complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for including removing debris from site etc complete all as specified and as directed.

M&L for RCC 1;2:4 type-B1, ( using 20mm graded stone aggregate) as in slab supported on wall , beams and columns in floor, roofs,landings, balcanies, canopies, deck slabs and in shelves and similar works etc complete all as specified and as directed.

S&F Door closer , aluminium (die cast body) , hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg etc complete all as specified and directed.

S&F 5.5 mm thick, Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane etc complete all as specified and directed.

S&F in repair 12 mm Prelaminated particle board,interior grade , prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with stainless steel screws to timber frame work etc complete all as specified and directed.

S&F Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified etc complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified etc complete all as specified and directed.

S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete etc complete all as specified and as directed.

M&L for PCC type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in coping and similar work including necessary formwork etc complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base, finished even and rough without using extra cement complete all as specified and as directed.

M & L for 100 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring ,laid in alternate panels 2m x 2m finished even and smooth without using extra cement complete all as specified and as directed.

Forming 12 mm thick expansion joints in PCC slab / floor , filled with 100 mm thick pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ etc complete all as specified and as directed.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade ‘A’ etc complete all as specified and as directed.

M&L Point wiring ( Concealed type) with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including 20 mm PVC conduit medium duty of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one 3 pin socket outlet 5/6 Amps and one bell point on independent board controlled by one one way switch. Note:- Cutting / chasing in brickwall / concrete wall for concealed wiring shall only be done with chase cutter machine.

All as per Item No.68.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 2.5 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 15/16 Amps, flush type, 240 volts complete all as specified and as directed.

S&F Decorative ultra slim linear LED batten light fitting with co extruded polycarbonate body enviornmental friendly, energy efficient , E-LITE LED GREEN suitable for 20/22 watt LED 6000K , 240 volts LED tube light ( single side connection ) including 1 x 22 watt LED tube rod etc complete all as specified and directed.Make:- Wipro / Havells / Philips / Crompton / Bajaj.

S&F Exhaust fan , metallic heavy duty AC single phase 230 / 240 volts of weep 300 mm with plastic self closing louver and making necessary electric connection with flexible copper conductor cable 1.5 sqmm 3 core PVC insulated etc complete all as specified and as directed. Make:- Usha / Crompton / Havells / Bajaj.

Supply and fix MCB Distribution board , 240 volts Single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer -in- Charge . Make : Havells, Cat Part No:DHDPSHODRW08 or Legrand Cat part No 5076-10 or equivalent model from make:- Siemens / Schneider / L&T.

Supply and fix MCB SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make: Havells Cat Part No:DHMGCSPF006-032 or Legrand Cat part No 603231 37 or equivalent model from make:- Schneider / Legrand.

Supply and fix MCB SPN, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make: Havells Cat Part No:DHMGCSNF040 or Legrand Cat part No 603248 54 or equivalent model from make:- Schneider / L&T

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F New generation energy saving building security light luminiries housing of versatile pressure die cast aluminium IP-66 with high power LED light 25 watt 230 volts 50 Hz with ballast / charging unit including all accessories , pre-wired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 3 m length ,fixed to pole / wall etc and testing etc complete all as specified and directed.Make:- Wipro Cat part No LR02-291-XXX-57-XX or equivalent make in Havells / Crompton / Bajaj.

MS J B CONSTRUCTION AND CO