Special repair to Bldg No P-26 (OTM Accn) at Udaipur Mil station

Amount

Demolition of cement concrete(unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down wooden chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down wooden chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Material and labour 400x400x7mm thick colour galzed ceramic jointless tiles (non skid) as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material and labour for glazed and coloured ceramic joint free tiles 300 mm X 600 mm x 7 mm thick, as in vertical surfaces such on skirting, dados and riser to steps. etc set and joined in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in cement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Material and labour for machine cut Udaipur green marble 16 to 18 mm thick pre polished (of size not less than 55 cm X 55 cm) in floor, laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste and edge molding over and including cement screed bed 20mm thick in cement mortar (1:4) complete all as specified.

Material and labour for machine cut Udaipur green marble 16 to 18 mm thick pre polished (of size not less than 55 cm X 10 cm) and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste and edge molding over and including cement mortar 10 mm thick in cement mortar (1:4) in skirting complete all as specified.

Material and labour for machine cut Kota stone slab 16-18 mm thick laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.

Material and labour for 50mm thick, PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in plinth protection/PCC path, and paving, finished the surface even and fair without using extra cement, laid in alternate bays, with constn, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand complete all as specified.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

Supply & fixed in repair vitreous china wash hand basin flat back white of size 550mmx400mm with 32 mm dia chromium plated waste coupling including flush pipe etc complete all as specified.

Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified.

S&F vitreous china wash down water closet (Pedestal pattern white with trap (excluding flushing cistern and flush pipe) and making connection with drain and to flushing pipe etc. including plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed by Engr-in-Charge.

S&F CP jet for EWC with PVC connection 15mm x 450mm size with one side CP brass check nuts and rubber washer including wall bracket complete.

Supply and fixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified. (Note : Weight of pillar tap shall not be less than 0.665 Kg) Make: Plumber/Prayag/Pearl/Jaquar Essco

Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, chromium plated, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. (Note : Weight of bib tap shall not be less than 0.575 Kg)

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supply & fixed GI tubing medium grade 15mm dia incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc, and making good the surfaces matching to exsiting surafaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

All as per Srl item No.22 above but 20mm complete all as specified.

Supply and fixed (in repair) stop valves, 15 mm dia pipe, chromium plated, ISI marked, screwed down, high pressure with crutch or butterfly handle (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified.(Note : Weight of bib tap shall not be less than 0.575 Kg)

Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of angle cock shall not be less than 0.575Kg).

Supply and fixing (in repair) two way angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of angle cock shall not be less than 0.575Kg).

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed in repair CP brass soap tray fixed with brass screw complete all as specified.

Supply and fixing for mild steel framed work as in door chowkats /gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides),

Material & Labour for PCC1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast ,back of pressed steel chowkats complete all as specified and directed.

Supply and fixed 35mm thick Flush shutters, solid core construction, with partical board core and plywood face panels, commercial type on both sides complete all as specified.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and fixing factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixing to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30 mm thick (stiles) with 2,4, or 6 raised panel design with 2mm thick moulded PVC seat on the front face and 2mm plane cover PVC seat on back face supply and fixing in frames at site as per specification and drawing.

S&F 100mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed..

Supply and fixing 200 mm mild steel barrel tower bolts, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified.

Supply and fixing mild steel pressed handles, oval type, enameled black 150mm long, complete all as specified.

Supply and fixing 300 mm mild steel sliding door bolts, ISI marked, stove enameled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified

Supply & fixed MS helical door spring 150 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.

S&F steel window box type ERW hollow 'P' section comprising double frame including gazed and glaized and skelton shutter 13mm thick jointed internally with flat iron 25 x 3mm complete including hinges handel tower bolts, stop lugs, grill etc. all as shown in drawing CEJZ TD/20 sheet 1/3 to 3/3 as applicable complete. Note:- (i) Frame shall consist and openable cooler area. (ii) For the purpose of measurement and payment double shutter with frames and grill shall be considered as one unit. (iii) Glazing, wire mesh and painting shall be measured and paid seperately.

Supply & fixed Powder coated aluminium ventilator fixed type without sash bar, aluminium section weighing 0.55 kh/m including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw etc complete all as specified.

Supply & fixed for pwoder coated aluminium grill of 7.00mmx3mm thick section square, rectangular, triangular, circular shape aperture not exc 7 cm in length or width fixed with H or F channel all as specified and directed.

Supply & fixed steel for 5mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample

Supply & fixing of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample as in repair.

Supply & fixing of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repaie complete all as specified.

Supply & fixing of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample as in repair complete all as specified.

Taking down cement plaster from brick walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work, concrete surfaces in cement mortar 1:4 mixed with WPC as per manufacturer’s instructions, finished even and fair, complete all as specified. (Note : WPC shall be measured and paid separately)

Material and labour 5 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick Birla White/JK White wall care putty on plastered for neat and smooth finishing including preparation complete. alll as specified.

Material & Labour for preparing new plastered surfaces and applying three coat of white wash on ceiling complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coat of cement base paint over a coat of primer/white wash complete all as specified.

Material and labour for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceiling complete all as specified.

Material and labour for Preparation of old Plastered or un-plastered surfaces of walls, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on walls complete all as specified.

Complete removal of existing treatment of wall and applying two coat of oil emulsion distemper over 1mm thick Birla White/JK White wall care putty in two layer on plastered surface for neat and smooth finishing complete all as specified and directed.

Complete removal of existing treatment and applying two coat of cement base paint on wall complete all as specified and directed.

Supply & fixed for sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each and glazing with oil putty to steel window complete all as specified.

M&L for two coat of synthetic enamel painting to wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer cpmplete all as specified and directed.

Description all as per ser item No 65 herein before but on steel surface over a coat of red oxide primer complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and directed.

Supply & Fixed for 100mm bore cast iron pipe in any length including jointing with cement complete all as specified.

Supply & Fixed cast iron bend 100mm bore complete all as specified.

Supply & Fixed branch pieces cast iron single (equal or unequal) 100mm bore complete all as specified.

Material and labour in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Dismantling water tanks 500 to 1000 Ltrs capacity (Steel/AC/RCC tanks) & removing from site all as specified.

S & F of rotational moulded HDPE water torage tank 1000 Ltr capacity weight not less than 18 kg (cylindrical vertical cosed top) with threaded lead triple layered in white coloured ISI marked hoisted and fixed in position in position complete.

Supplying & laying 03 coats of Dr. Fixit heavy duty, reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed. Make : Dr. Fixit New coat & Equivalent

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Material & labour for 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Supply only liquid water proofing compound, complete all as specified.

Material and labour Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour Preparation of old painted steel or iron based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in slab supported on wall,beam, cantilevers and kitchen cooking platform complete all as specified.

Material and labour for RCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in chajjas beams etc complete all as specified and directed.

Material and labour for carrying out water proofing treatment for roofs in the following stages and as directed by Engr-in-Charge”. Note: Refer Clause 43 of Particular Specifications on Page No 164.

S&F in repair PVC ball valves high pressure with epoxy coated aluminium rod and high density palstic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-Charge

Supply & Fixed in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed Make:Kirloskar/Zoloto/Upadhyay

S&F in repair fancy type shower rose 125mm dia size of rim and 30cm long CP brass pipe with swivel joint complete all as specified.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge.

M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified (Make of cable: Kalinga/Havells/Anchor) for One light point / Fan/ bell point controlled by one switch.(a) One light point controlled by one 5 Amps switch

All as per item no 88 above but One Fan point controlled by one 5 Amps switch

All as per item no 88 above butOne socket 3 Pin 5A pin socket oulet 5Amps on same board with cables 1.5 Sqmm size

All as per item no 88 above but One socket 3 Pin 5A pin socket oulet 5Amps on indepndent board with cables 1.5 Sqmm size.

All as per item no 88 above butOne socket 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size

All as per item no 88 above but One light point controlled by two 2-way switch

All as per item no 88 above but for One socket 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size for geyser point

S&F switch piano flush type single pole one way 5/6 Amps.

S&F switch piano flush type single pole two way 5/6 Amps.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd

S&F lamp holder Angle / batton type insulated body with back plate and to be fixed on PVC bock. Including dismantling old one.

S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one.

S&F of switch piano15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one.

S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one

S&F ceiling rose surface tpe 3 terminals to be fixed on PVC block including dismantling old one.

S&F LED integrated batten tube light fittings 20/22 Watt 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed

M&L MCB SPN DB sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 8 way including dismantling old one. Make : Havells / Legrand / Schneider/Standard

S&F RCBo'S DP 30mA 230 Volts 32 Amps. Make : Havells/Legrand/Standard/ C&S

S&F MCB SPN 230 Volts 40 Amps. Make : Havells/Legrand/Standard/ C&S

S&F MCB SP 230 Volts 6- 32 Amps. Make : Havells/Legrand/Standard/ C&S

Fixing LED lamp 9W system lumen (NOM) 600 with all accessories all as specified and directed by Engr-in-Charge. Note: LED Bulbs will be issued under Sch 'B"

Hanging only ceiling fan (M.D.supply) and connecting up including provision of cable from ceiling rose or connector to fan

S&F exhaust fans AC single phase 230/240Volts of size 150/200 mm sweep with louver and complete accessories ,including making hole with suitable size for Exhaust Fan, after completion of work, finishing with cement and plastering and repainting with exisitng color all as specified and directed by Engr-in-charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5core

Excavating in trenches n.exc 1.5 m width and n.exc 1.5m in depth for taking out cable and cable cover and getting out in any type of soil

Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point

M&L for sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables. Note :- For the purpose of payment only punned thickness will be measured

Material and labour for stone slab ( patti) roughly hammer dressed stone 25 to 35 mm thick 25 to 30 cm wide and not less than 60 cm long laid dry and abutting each other with gap between adjacem,ent salb not exceeding 10 mm over underground cables for protection.

Taking out old unserviceable protection Pipe and supply and fix light grade 40 mm dia GI pipe fix complete to Wall , Poles etc with suitable clamp for protection of cable complete all as directed

S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x1.5 sqmm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

S&F Submain wiring alongwith earth wire with the following sizes of 2x 4.0 sqmm + 1.25 sqm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

S&F LED security light luminaries of 25 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 1.5 sqmm stranded copper conductor of suitable length as per direction and approved by Engr-in-charge, Make: Crompton or equivalent to phillips/Bajaj

Taking down old Sheet metal enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated made out of 1.6 mm thick CRCA sheet with front side openable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate made out of 2mm thick CRCA sheet steel and earth bolts etc. of size 600x500x200mm all as speceified & directed by Engr-in- charge. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and making good the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item.

Punjab Traders

M/S HARI CONSTRUCTION

L AND J CONSTRUCTION CO.

M/s SUNIL ENTERPRISES

M/S JAGDAMBA ENTERPRISES