BARC/TSD/77/2021-22

Amount

DISMANTLING PLAIN CEMENT CONCRETE (PCC) manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200m lead as per direction of Engineer-in-charge.

DISMANTLING OLD PLASTER OR SKIRTING carefully, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100m lead.

DISMANTLING TILE WORK IN FLOORS AND ROOFS laid in cement mortar including stacking material within 100m lead for thickness of tile up to 25mm etc. complete as directed by Engineer in charge.e.

DISMANTLING TILE WORK IN FLOORS AND ROOFS laid in cement mortar including stacking material within 100m lead for thickness of tiles above 25mm and up to 40mm.

DISMANTLING DOORS, WINDOWS AND CLEAR STOREY OPENINGS (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100m lead (full windows) of area 3.00 Sq.M and below.

DISMANTLING DOORS, WINDOWS AND CLEAR STOREY OPENINGS (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100m lead (full windows) of area beyond 3.00 Sq.M.

LEAD CHARGES FOR LEAD UPTO 30 KM by mechanical transport includinmg loading,unloading, stacking / levelling etc. (Note:Note: The rates in respect of Item Nos 25 to 30 are applicable for NET Quantities arrived at after making deduction for voids @ 30% from corresponding TRUCK Measurement). Note: Trasporting of debries at disposal ground, disposing, stacking, leveling & statutery charges if any will be responsibility of the Contractor and no extra charges shall be paid for the same.

Debris Beyond 4 Km but up to and including 30 Km.)

Providing and laying in position CEMENT CONCRETE OF 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels..

Providing and constructing BRICK WORK in cement mortar using Standard bricks of approved quality / class, make / brand in super structure above plinth up to Floor-II level in all shapes and sizes including curing, raking out joints complete as per specifications and as directed by the Engineer-in-charge. Brickwork in super structure with standard bricks in C.M 1:4 using crushed sand.

Providing and Laying AUTOCLAVED AERATED CEMENT BLOCK MASONRY of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20 m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work.

Providing 15mm THICK INTERNAL PLASTERING USING READY MIX INTERNAL PLASTERING COMPOUND of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Providing 20mm THICK INTERNAL PLASTERING in C.M without cement punning 1:4 (using crushed sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing and fixing 1st quality CERAMIC GLAZED WALL TILES conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing GLAZED VITRIFIED FLOOR TILES in floor and dado of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Using Tiles of size 600 X 600 mm

Providing and laying FLOORING PLASTER OF PARIS 8mm thick over new laid tiles including spreading polythene paper, curing, levelling, removal and disposal of same before cleaning floor, labour, tools etc. complete and as directed by Engineer in charge.

Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (Premoulded and Prepolished) machine cut GRANITE OF TELEPHONE BLACK COLOUR FOR KITCHEN PLATFORMS, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels.

Extra for providing EDGE MOULDING TO 17mm THICK MARBLE STONE / GRANITE SLAB counters, Vanitis etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge. Granite work

Providing WOOD WORK IN FRAMES OF DOORS, WINDOWS, CLEAR STORY OPENINGS and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge. Using

Providing and fixing 35mm THICK FLUSH DOOR SHUTTERS conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Providing and fixing IS:12817 marked STAINLESS STEEL BUTT HINGES of size 125 x 64 x 2.5 mm (heavy weight) of approved make with suitable stainless steel screws etc. complete as directed by the Engineer-in-charge

Supplying, providing and fixing DOOR CLOSER TS 71- DORMA- STD ARM or approved equivalnet with necessary screws, fixing to the aluminium/glass/wooden door complete as per drawing, specifications including all labour, transporting charges etc. & as directed by EIC.

Providing and fixing MORTICE LATCH AND LOCK of approved make with 6 levers and a pair of handles Inside opening LEFT / Right with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing STAINLESS STEEL TOWER BOLTS OF SIZE 250mm X 12mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing ALUMINIUM HANGING HEAVY QUALITY FLOOR DOOR STOPPER ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Supplying, providing and fixing STAINLESS STEEL-304 D-HANDLES (MATT FINISH) OF LENGTH - 300mm, DIAMETER-25mm, suitable S.S. fange , S.S. cap and thickness 16 Guage thickness to brick Walls, R.C.C. surface, Wooden doors etc. including drilling, S.S. Screws of 30mm long ( 6 Nos for each handle) ,cost of labour, tools, tackles ,wooden gutties, plants, transportaion, scaffolding etc. all complete as per site requirement and as directed by Engineer in charge.

Providing and fixing WATER PROOF MARINE PLY (Kit ply, Anchor ply or equivalent) the rates are exclusive screws, washers etc complete providing and fixing hard wood leaping around board in walls etc. By using 12 mm thick water proof marine ply.

Providing and fixing DECORATIVE HIGH PRESSURE 1.0mm THICK LAMINATED SHEET OF PLAIN / WOOD GRAIN in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed by Engineer-In-Charge.

Supplying, Providing and fixing BEADING (ARCHITRAVE) of size 50mm to 65mm wide and 12 mm thick using 2nd class teak wood/water proof marine ply around the door frames with necessary screws and fixing laminated sheet on top etc. complete as directed by the Project Engineer.

Providing and fixing 25mm thick SOLID PVC INTEGRAL SHEET FLUSH DOOR SHUTTER of M/s Jain Irrigation System Ltd. of white colour or as directed by Engineer-in-Charge. Made out of J1054 Integral Foam Sheet and including fixing with 4 Nos 100 mm ISI marked heavy quality stainless steel butt hinges with S.S. necessary screws

Providing and fixing 25 mm S.S. CURTAIN RODS of 1.25mm thick with two SS / Brass brackets fixed with SS / Brass screws and wooden plugs etc.wherever necessary complete.

Providing, supplying and fixing VENTILATION VERTICAL BLINDS (approved) with all accessories and fabricating to required sizes etc as per approved design and approved Fabric complete all as directed by the Project Engineer.

Providing and Supplying SOLID PVC INTEGRAL SHEET Made out of J1054 Integral Foam Sheet of M/s Jain Irrigation System Ltd. of white colour or as directed by Engineer-in-Charge.

12mm thick

18mm thick

25mm thick

Providing and fixing ANODIZED ALUMINIUM WORK FOR DOORS, WINDOWS, VENTILATORS and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for COLOUR ANODIZING / DYED ANODIZING

Providng and fixing Aluminium Grill 10 mm thick "DECO GRILLE" make Model No. DG- 202 in natural Silver anodising of min 15 Micronswith a opening size of 60mm x 45mm and Minimum weight of 4.12 Kg/ Sq.M including providing anfd fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-charge .Aluminium alloy shall be of 6063-T6 with yield strength of minimum 6.5 kg/ sq.mm.

Extra for providing ALUMINIUM GRILL 10mm THICK WITH COLOUR ANODISED by the manufacturer (Champagne, black, Bronze, Gold colours) complete all as per specifications and as directed at site by the Engineer-in-charge

FILLING THE GAP WITH SILICON SEALANT between aluminium frame & adjacent RCC / Brick work / Stone work over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm depth and 5 mm widthe)

Providing and fixing GLAZING IN ALUMINIUM DOORS, WINDOW, VENTILATOR shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-Charge (Cost of snap beading shall be paid in basic item).

With clear float glass panes of 5.00 mm thickness

With tinted colour float glass panes of 5.0 mm thickness

Providing, supplying and fixing S.S. MESH-(MOSQUITO NET) - 0.50MM THICK - 144 APERTURE IN SQ. INCH to aluminium grill / frame including cost of all accessories and fabricating to required sizes etc complete all as directed by the Engineer-in-Charge.

Providing and fixing Approved Quality STAIN LESS STEEL BODY ROLLER WHEELS of approved make for Sliding shutters.

Providing and fixing Approved Quality and shape STAR LOCKS cum Handle of MIDIN or approved equivalent make for Sliding shutters.

Providing and fixing 6mm THICK MIRRORS OF SIZE 600mm X 450mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 6mm THICK MIRRORS of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge.

Providing and fixing in position SUSPENDED FALSE CEILING SYSTEM / PARTITION SYSTEM USING 12mm THICK CALCIUM SILICATE BOARDS (HILUX CEILING SYSTEMS) 100% humidity resistance, incombustible as per BS476 part IV with thermal conductivity of 0.043 w/m KC placed in a suspended grid of size of 600x 600mm made of hot-dipped G.I steel sections wherein the ceiling sections of 0.55 mm thick shall be suspended at 1200 mm centres along the length of ceiling with 4mm dia G.I wires/ 1 mm thick strip hangers made of G.I sheet sections with necessary level adjusters and inter channels of 0.90mm thick with connecting clips and resting on the perifery walls on wall angles of 0.55 mm thickness including providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings and as per directions of Engineer-in-charge The main tees to be suspended from the ceiling/ soffit with the help of metal dash fastners of 6mmx50mm, soffit clits of 25mmx35mmx1.60mm and 4mm dia G.I wire with galvanised spring steel levelling clips/ G.I strip Hangers at 600mm centers . the entire grid system shall be designed to bear a distributed load of minimum 25 kg/Sq.m (Only calcium silicate false ceiling area will be measured for the purpose of payment)

Providing and fixing STAINLESS STEEL SATIN FINISH KITCHEN SINK AISI 304 (18/8) with drain board with over all size of 1145 x 510 mm and bowl size of 560 x 410 mm and 200 mm depth of approved make and model with C.I. brackets and stainless steel waste coupling, fittings, including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever requried.complete as per specifications and as directed by the Engineer-in-charge

Providing, applying wall painting two coats on old work with premium PLASTIC EMULSION PAINT of approved brand to give an even shade with a coat of cement primer, including preparation of the surfaces, scaffolding complete as per specifications and as directed by the Engineer-in-charge

Providing and Painting two coats of SYNTHETIC ENAMEL PAINT on steel surfaces of approved brand and manufacture to give an even shade over a primer coat.including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

SUNIL CONSTRUCTION