GE/CHM-99/2025-2026 PROVN OF GUARD ROOM WITH ALLIED INFRASTRUCTURE UNDER AGE B/R III AT CHANDIMANDIR

Amount

Surface dressing n.exc 15cm deep in hard dense soil complete all as specified and directed

Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removal excavated soil to a distance exceeding 50 metre but n.exc 250 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified & directed.

Excavation over areas in hard/dense soil not exceeding 1.50 metre in depth and getting out complete, all as specified.

providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundations, filling and mass concrete etc., complete all as specified and as directed

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix), using 20mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix), using 20mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix), using 20mm graded crushed stone aggregate) as in Chajja and similar works, all as specified. Note : Reinforcement and form work shall be measured and paid separately

Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix), using 20mm graded crushed stone aggregate)as in Beams, cantilevers, bressummers, lintels over 1.5m span , all as specified and directed.

Reinforced cement concrete type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter , all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surface of flat concrete complete all as specified and directed.

Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for roughly finished flat surfaces of concrete, all as specified.

Form work to soffits of suspended slabs such as roof slabs rough finished surface of concrete flat not exc 200mm thick complete all as specified and directed.

Form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work.

MS TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified & directed. (Stirrups)

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 complete all as specified & directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over brick or concrete surfaces finished even and fair without using extra cement complete, all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and fair without using extra cement complete, all as specified and directed.

Rendering 5mm thick in CM 1:3 on fair faces of concrete/brick surfaces as in ceiling, chajja, facia or similar positions , finished fair and smooth complete all as specified and directed.

Earth filling under floor including spreading and levelling in in layers n.exc 25cm thick complete all as specified & directed.

Hard core of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

75mm thick plain cement concrete type C-2 1:3:6(Using 40mm graded crushed stone aggregates) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring, finished even and fair complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mmx450mmx 7mm thick as in dado, set and jointed in neat cement slurry and grouted in white cement complete as on vertical surfaces over and including 10 mm thick bedding layer in CM 1:4 complete all as specified and directed.

20mm thick Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like, set in 20mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte including moulding on front edge all as specified and directed.

Supply only integral water proofing compound complete all as specified & directed.

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one coat of red oxide primer etc complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290-0 or Fe 165-0, all as specified and directed.

Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square, area not exc 0.5 sq. mtr in each pane,complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including filling of PCC 1:3:6 in hollow frame complete all as specified and directed.

Factory made second class hard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, all as specified and directed.

35mm thick of second class hard wood glazed and Skelton shutter open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc.; Size of members of shutters as specified in SSR Part 1, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

Stainless steel butt hinges, 100mm long fixed to steel chowkhats by welding, bolting, riveting etc, complete all as specified & directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm aluminium handles cast type complete all as specified and directed.

Supply and fixing aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed complete all as specified and directed.

Steel windows , ventilator fixed type with glazing bars, including one shop coat of red oxide zinc chrome primer, complete all as specified & directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

RCC pipes class NP2 200mm dia bore, with collars, ISI marked, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed.

Plain cement concrete type C-2, 1:3:6 using 40mm graded crushed stone aggregate as in bed to drain pipes including cradle of pipe after the pipes are laid and tested , complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

75mm bore PVC (SWR) bend any radius complete all as specified and directed.

110mm bore PVC (SWR) bend any radius complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

PVC (SWR) floor trap 100mm bore, plain with grating including jointing with solvent cement, complete all as specified and directed.

Steel water tubes, 15mm dia bore, medium grade, galvanized, with and including all fittings and fixed complete to walls ceiling or laid in floors, complete all as specified and directed.

Steel water tubes, 20mm dia bore, medium grade, galvanized, with and including all fittings and fixed complete to walls ceiling or laid in floors, complete all as specified and directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest including 'P' or 'S' trap, flush pipe (excluding flushing cistern) and making good to the floor complete all as specified & directed by Engineer-in-charge.

Vitreous China Wash down water closet (pedestal pattern) , white, with and including PVC seat cover, complete all as specified and directed.

PVC valve less syphonic action flushing type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC bend for squat pedastal pattern , complete all as specified & directed.

Vitreous China wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete, all as specified and directed.

Bib tap, fancy type cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Wall mixer, mix for mixing hot or cold water, chromium plated suitable for 15mm bore GI pipe or union, complete all as specified and directed.

Stainless steel grating 127mm complete all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm , complete all as specified and directed.

32mm dia PVC waste pipe with PTMT nut, complete all as specified and directed.

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), complete all as specified and directed.

Soap dish of cast copper alloy, chromium plated (CP), complete all as specified and directed.

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, complete all as specified and directed

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

health faucet (ABS body) mild steel chromiu plated for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook incuding making connections and fixed in position, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with CP bracket guard and railing 60cm long, complete all as specified and directed.

Toilet paper holder, stainless steel, chromium plated fixed in position, complete all as specified and directed.

1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, screwable lid, hoisted and fixed in position, including tank nipple, float valve, ball valve 20mm PTMT, complete all as specified and directed.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complte all as as specified and directed

Vitreous China Urinal, Half stall type, white and including flushing cistern, flush pipe and waste pipe,complete all as specified & directed

Precast concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, and including laid over 25mm thick sand cushioning, complete all as specified and directed

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid over a coat of oil bound bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS. The membrane shall be laid using butane torch and sealing all joints etc having 75mm side lap joint and 100m end lap joint after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying one coat of bituminous aluminium paint @100gm/sqm on top of membrane, complete all as specified & directed.

15mm thick rendering in Cement and Sand mortar 1:4 over roof slab and sunken portion finished even and fair mixed with water proofing compound, including dimantling of the existing roof slab / suken portion complete all as specified. (NOTE : WPC will be measrued and paid separately)

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 88 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 88 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 88 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

LED lamp 9 watts, B-22 type complete all as specified .

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 04 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB , TPN/FP 40 to 100 Amp 415 volts, 16 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

Single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amp MCB 'C' series single pole complet all as specified and directed.

LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete all as specified and directed.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. NOTE : - (i) Two runs of cable, one run of earth wire shall be considered as one running metre (ii) Cutting chases and conduit will be measured and paid separtely (iii) colour code shall be Red for phase, Black for neutral and green for earth

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

25mm dia, rigid non metallic PVC concealed conduit, 'ISI marked', inclusive of all fittings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing accessories such as couplers lock nuts, saddless, pipe hooks etc for wiring, Complete all as specified and directed .

Exhaust fan, steel body AC single Phase. 230V of size 300mm sweep , 1400 rpm, heavy duty with, blades, and frame and louvers including grouting nuts, fastners and provision of flexible coper cable 3 core form ceiling rose to exhaust fan complete all as specified and directed.

Supply, installation, commissioning of water cooler partially stainless steel, electric driven single phase having approx storage and nominal cooling capacity 40/40 ltrs complete all as specified and directed.

Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and provision of flexible copper cable 3 core from ceiling rose to fan complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complet, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

Electric water heater(vertical type geyser), capacity 25 litre, 2 KW BEE 5 Star rated AC single phase, including MS glass lined inner tank, glass coated heating element, high density PUF insulation, Anode rod protection, heavy duty fastner not less than 100mm with suitable size of nut & washer grouted in wall with complete mason work for proper mounting of geyser fastner bolts with all accessories such as safety valve, thermostat, NRV, connection piece etc. making necessary inlet / outlet water connection, testing on load complete all as specified and directed.

Supply and installation evaporative desert coolers (steel body) factory made 22/24 gauge PGI sheet of size100x70x60cm appx, front and side panels are made of same gauge with wood wool pad shaving nominal air flow capacity of 4000 cfm, or nearest size, having exhaust fan motor with copper winding of capacity 280 to 310 watt with 18” steel blade size, and submersible pump of capacity 1.5m head , and powder coated, with all fittings and fixtures as directed by Engr-in-Charge onsite complete all as specified and directed.”(Make-Champion or equivalent.) Note :- The rates are included of material and labour for Fabrication cooler stand size 60x70x80cm ( LxWxH) angle iron of 35x35 x 5mm as directed conforming to Fe-290Gde E-165, including cutting, welding, cross support in upperside and lower side with flat iron or angle iron of 35x35x5 etc, two coats synthetic enamelpaint over one coat redoxide primer, installed in location complete all as specified and directed.

32mm outer dia, double walled corrugated (DWC) HDPE duct pipe pipes of pressure rating 6 kgf/sq. cm conforming to IS 14930 Part-II with anti rodent and non flame propogating properties of approved colour with fittings for cable protection as approved by Engineer-in-charge complete , all as specified and directed

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16sqmm, 2 core, laid in trenches , sleeving through pipes of fixed on poles & wall or laid under floors inlcuding jointing with suitable size of alumunium lugs as specified and directed.

JOGINDER NATH GUPTA AND SONS (BID ID -3500680)